International System of Units

"SI" redirects here. For other uses, see Si (disambiguation).

For a topical guide, see Outline of the metric system.

The seven SI base units and the interdependency of their definitions. Clockwise from top: kelvin (temperature), second (time), metre (length), kilogram (mass), candela (luminous intensity), mole (amount of substance) and ampere (electric current).

The International System of Units (abbreviated SI from French: Le Système international d'unités) is the modern form of the metric system. It comprises a coherent system of units of measurement built around seven base units, 22 named and an indeterminate number of unnamed coherent derived units, and a set of prefixes that act as decimal-based multipliers. The standards, published in 1960, are based on the metre-kilogram-second system, rather than the centimetre-gram-second system, which, in turn, had several variants. The SI has been declared to be an evolving system; thus prefixes and units are created and unit definitions are modified through international agreement as the technology of measurement progresses, and as the precision of measurements improves. SI is the world's most widely used system of measurement, used in both everyday commerce and science.

The system has been nearly globally adopted. Burma, Liberia and the United States have not adopted SI units as their official system of weights and measures. The U.S. does not commonly use metric units outside of science, medicine, and the government, but has officially defined its customary units in terms of SI units. The United Kingdom has officially adopted a partial metrication policy, with no intention of replacing imperial units entirely. Canada has adopted it for most purposes but imperial units are still legally permitted and remain in common use throughout a few sectors of Canadian society, particularly in the buildings, trades and railways sectors.

History

Main article: History of the metric system

The metric system was first implemented during the French Revolution (1790s) with just the metre and kilogram as standards. In the 1860s British scientists, working through the British Association for the Advancement of Science laid the foundations for a coherent system based on length, mass and time, but the inclusion of electrical units into the system was hampered until 1900 when Giorgi identified the need to define an electrical quantity alongside the original three quantities. Meanwhile, in 1875, the Treaty of the Metre passed custodianship of the prototype kilogram and metre from French to international control. In 1921 the Treaty was extended to include all physics measurements and in 1948 an overhaul of the metric system was set in motion which resulted in the publication of the International System of Units in 1960.

Uncoordinated development

Old boundary stone in Pontebba, marking the former border between Austria-Hungary and Italy; the myriametre (10 km), since deprecated, was in common use in Central Europe during the mid-nineteenth century.

The metric system was developed from 1791 onwards by a group of scientists commissioned by the Assemblée nationale and Louis XVI of France to create a unified and rational system of measures. The group, which included Antoine-Laurent Lavoisier (the "father of modern chemistry") and the mathematicians Pierre-Simon Laplace and Adrien-Marie Legendre, used the principles that had been proposed by the English cleric John Wilkins in 1668 and naming concepts developed from those proposed in 1670 by the French cleric Gabriel Mouton. On 1 August 1793, the National Convention adopted the new decimal metre with a provisional length as well as the other decimal units with preliminary definitions and terms. The law of 7 April 1795 (Loi du 18 germinal, an III) defined the terms gramme and kilogramme which replaced the former terms gravet (correctly milligrave) and grave, and on 22 June 1799, after Pierre Méchain and Jean-Baptiste Delambre completed their survey, the definitive standard metre was deposited in the French National Archives. On 10 December 1799 (a month after Napoleon's coup d'état), the law by which metric system was to be definitively adopted in France was passed.

During the first half of the nineteenth century there was little consistency in the choice of preferred multiples of the base units – typically the myriametre (10,000 metres) was in widespread use in both France and parts of Germany, while the kilogram (1,000 grams) rather than the myriagram was used for mass.

In 1832 Carl Friedrich Gauss implicitly defined a coherent system of units when he measured the earth's magnetic field in absolute units quoted in terms of millimetres, grams, and seconds. In the 1860s James Clerk Maxwell and William Thomson (later Lord Kelvin), working through the British Association for the Advancement of Science formulated the concept of a coherent system of units with base units and derived units. The principal of coherence was successfully used to define a number of units of measure based on the centimetre–gram–second (cgs) system of units (cgs) including the erg for energy, the dyne for force, the barye for pressure, dynamic viscosity in poise and the kinematic viscosity in stokes.

Metre Convention

The desire for international cooperation in metrology led to the signing in 1875 of the Metre Convention, a treaty that established three international organisations to oversee the keeping of metric standards:

• General Conference on Weights and Measures (Conférence générale des poids et mesures or CGPM) – a meeting every four to six years of delegates from all member states;
• International Bureau of Weights and Measures (Bureau international des poids et mesures or BIPM) – an international metrology centre at Sèvres in France; and
• International Committee for Weights and Measures (Comité international des poids et mesures or CIPM) – an administrative committee that meets annually at the BIPM.

Initially the convention only covered standards for the metre and the kilogram, new prototypes of which were manufactured by the British firm by Johnson, Matthey & Co and accepted by the GCPM in 1889. It was only in 1921 that the convention was extended to include all physical units that the CGPM was able to address inconsistencies in the way that the metric system had been used.

Towards SI

In the nineteenth century attempts to produce a coherent set of electrical units was beset with difficulties.

William Thomson, later Lord Kelvin, who, with James Clerk Maxwell, was one of the most influential figures in the theoretical development of the metric system.

At the close of the nineteenth century three different systems of units of measure existed for electrical measurements – a CGS-based system for electrostatic units (also known as the Gaussian system), a CGS-based system for electromechanical units and an MKS-based system (the "International system") for electrical distribution systems. In 1900 Giovanni Giorgi published a paper in which he advocated using a fourth base unit alongside the existing three base units. The fourth unit could be either electric current or voltage or electrical resistance.

James Clerk Maxwell, who, with William Thomson, later Lord Kelvin, was one of the most influential figures in the theoretical development of the metric system.

In the late nineteenth and early twentieth centuries a number of non-coherent units of measure were developed such as the Pferdestärke or "metric horsepower" for power, the darcy for permeability and the use of "millimetres of mercury" for the measurement of both barometric and blood pressure. All these units incorporate standard gravity in their definitions.

At the end of Second World War, a number of different systems of measurement were in use throughout the world. Some of these systems were metric system variations, whereas others were based on customary systems of measure. It was recognised that additional steps were needed to promote a worldwide measurement system. After representations by the International Union of Pure and Applied Physics (IUPAP) and by the French Government, the 9th General Conference on Weights and Measures (CGPM), in 1948, asked the International Committee for Weights and Measures (CIPM) to conduct an international study of the measurement needs of the scientific, technical, and educational communities.

Based on the findings of this study, the 10th CGPM in 1954 decided that an international system should be derived from six base units to provide for the measurement of temperature and optical radiation in addition to mechanical and electromagnetic quantities. The six base units that were recommended are the metre, kilogram, second, ampere, degree Kelvin (later renamed kelvin), and candela. In 1960, the 11th CGPM named the system the International System of Units, abbreviated SI from the French name, [Le Système international d'unités] Error: {{Lang}}: text has italic markup (help). The BIPM has also described SI as "the modern metric system". The seventh base unit, the mole, was added in 1971 by the 14th CGPM.

SI Brochure and conversion factors

File:SI Brochure Cover.jpg

Cover of brochure The International System of Units

The CGPM have published a brochure, the 8th edition of which appeared in 2006, in which the various recommendations that make up SI have been codified. This brochure leaves some scope for local interpretation, particularly in respect of language. The United States National Institute of Standards and Technology has produced a version of the CGPM document (NIST SP 330) which clarifies local interpretation in respect of English-language publications that use American English and another document (NIST SP 811) that gives general guidance for the use of SI in the United States.

The writing and maintenance of the CGPM brochure is carried out by one of the consultative committees of the International Committee for Weights and Measures (CIPM) – the Consultative Committee for Units (CCU). The CIPM nominates the chairman of this committee, but its membership is made up of representatives of various other international bodies rather than CIPM or CGPM nominees. This committee also provides a forum for the bodies concerned to provide input to the CIPM in respect of on-going enhancements to SI. In 2010 the CCU proposed a number of changes to the definitions of the base units used in SI. The CIPM meeting of October 2010 found that the proposal was not complete, and it is expected that the CGPM will consider the full proposal in 2014.

The definitions of the terms 'quantity', 'unit', 'dimension' etc. that are used in the SI Brochure are those given in the International Vocabulary of Metrology, a publication produced by the Joint Committee for Guides in Metrology (JCGM), a working group consisting of eight international standards organisations under the chairmanship of the director of the BIPM. The quantities and equations that define the SI units are now referred to as the International System of Quantities (ISQ), and are set out in the ISO/IEC 80000 Quantities and Units.

Appendix B of NIST SP 811, a list of conversion factor between SI and customary units, is an extension to the SI Brochure.

Units and prefixes

The International System of Units consists of a set of base units, a set of derived units, some of which have special names and a set decimal-based multipliers that are denoted as prefixes. The term "SI Units" includes all three categories, but the term "coherent SI units" includes only base units and coherent derived units.

Base units

Main article: SI base unit

Base units are the building blocks of SI – all other units of measure can be derived from the base units. When Maxwell first introduced the concept of a coherent system, he identified three quantities that could be used as base units – mass, length and time. Giorgi later identified the need for an electrical base unit – theoretically electrical current, potential difference, electrical resistance, electrical charge or any one of a number of other units could have been used as the base unit with the remaining units being then defined by the laws of physics – the unit of electric current was chosen for SI. The remaining three base units were added later.

SI base units

Unit name	Unit symbol	Quantity	Definition (Incomplete)	Dimension symbol
metre	m	length	Original (1793): ⁠1/10000000⁠ of the meridian through Paris between the North Pole and the EquatorFG Current (1983): The distance travelled by light in vacuum in ⁠1/299792458⁠ of the duration of 9192631770 periods of the radiation corresponding to the transition between the two hyperfine levels of the ground state of the caesium 133 atom	L
kilogram	kg	mass	Original (1793): The grave was defined as being the weight [mass] of one cubic decimetre of pure water at its freezing point.FG Current (1889): The mass of the International Prototype Kilogram	M
second	s	time	Original (Medieval): ⁠1/86400⁠ of a day Current (1967): The duration of 9192631770 periods of the radiation corresponding to the transition between the two hyperfine levels of the ground state of the caesium 133 atom	T
ampere	A	electric current	Original (1881): A tenth of the electromagnetic CGS unit of current. [The [CGS] emu unit of current is that current, flowing in an arc 1 cm long of a circle 1 cm in radius creates a field of one oersted at the centre.]. IEC Current (1946): The constant current which, if maintained in two straight parallel conductors of infinite length, of negligible circular cross-section, and placed 1 m apart in vacuum, would produce between these conductors a force equal to 2×10−7 newton per metre of length	I
kelvin	K	thermodynamic temperature	Original (1743): The centigrade scale is obtained by assigning 0° to the freezing point of water and 100° to the boiling point of water. Current (1967): The fraction 1/273.16 of the thermodynamic temperature of the triple point of water	Θ
mole	mol	amount of substance	Original (1900): The molecular weight of a substance in mass grams.ICAW Current (1967): The amount of substance of a system which contains as many elementary entities as there are atoms in 0.012 kilogram of carbon 12.	N
candela	cd	luminous intensity	Original (1946):The value of the new candle is such that the brightness of the full radiator at the temperature of solidification of platinum is 60 new candles per square centimetre Current (1979): The luminous intensity, in a given direction, of a source that emits monochromatic radiation of frequency 540 × 1012 hertz and that has a radiant intensity in that direction of 1/683 watt per steradian.	J
Note The original definitions of the various base units in the above table were made by the following authorities: FG = French Government IEC = International Electrical Congress ICAW = International Committee on Atomic Weights

Derived units

Main article: SI derived unit

Derived units are formed from multiplication and division of the seven base units and other derived units and are unlimited in number; for example, the SI derived unit of speed is metres per second (symbol m/s). Some derived units have special names; for example, the unit of resistance, the ohm (symbol Ω), is uniquely defined by the relation Ω = m²⋅kg⋅s⁻³⋅A⁻², which follows from the definition of the quantity electrical resistance. The radian and steradian, once given special status, are now considered dimensionless derived units.

Named units derived from SI base units

Name	Symbol	Quantity	Relationship with other units	Dimension symbol
hertz	Hz	frequency	1/s	T−1
radian	rad	angle	m/m	dimensionless
steradian	sr	solid angle	m2/m2	dimensionless
newton	N	force, weight	kg⋅m/s2	M⋅L⋅T−2
pascal	Pa	pressure, stress	N/m2	M⋅L−1⋅T−2
joule	J	energy, work, heat	N⋅m = C⋅V = W⋅s	M⋅L2⋅T−2
watt	W	power, radiant flux	J/s = V⋅A	M⋅L2⋅T−3
coulomb	C	electric charge or quantity of electricity	s⋅A	T⋅I
volt	V	voltage, electrical potential difference, electromotive force	W/A = J/C	M⋅L2⋅T−3⋅I−1
farad	F	electric capacitance	C/V	M−1⋅L−2⋅T4⋅I2
ohm	Ω	electric resistance, impedance, reactance	V/A	M⋅L2⋅T−3⋅I−2
siemens	S	electrical conductance	1/Ω = A/V	M−1⋅L−2⋅T3⋅I2
weber	Wb	magnetic flux	J/A	M⋅L2⋅T−2⋅I−1
tesla	T	magnetic field strength	V⋅s/m2 = Wb/m2 = N/(A⋅m)	M⋅T−2⋅I−1
henry	H	inductance	V⋅s/A = Wb/A	M⋅L2⋅T−2⋅I−2
degree Celsius	°C	temperature relative to 273.15 K	K	Θ
lumen	lm	luminous flux	cd⋅sr	J
lux	lx	illuminance	lm/m2	L−2⋅J
becquerel	Bq	radioactivity (decays per unit time)	1/s	T−1
gray	Gy	absorbed dose (of ionizing radiation)	J/kg	L2⋅T−2
sievert	Sv	equivalent dose (of ionizing radiation)	J/kg	L2⋅T−2
katal	kat	catalytic activity	mol/s	T−1⋅N

Prefixes

Main article: Metric prefix

A prefix may be added to a unit to produce a multiple of the original unit. All multiples are integer powers of ten, and beyond a hundred(th) all are integer powers of a thousand. For example, kilo- denotes a multiple of a thousand and milli- denotes a multiple of a thousandth; hence there are one thousand millimetres to the metre and one thousand metres to the kilometre. The prefixes are never combined, and multiples of the kilogram are named as if the gram was the base unit. Thus a millionth of a metre is a micrometre, not a millimillimetre, and a millionth of a kilogram is a milligram, not a microkilogram.

Standard prefixes for the metric units of measure (multiples)

Prefix name	N/A	deca	hecto	kilo	mega	giga	tera	peta	exa	zetta	yotta	ronna	quetta
Prefix symbol		da	h	k	M	G	T	P	E	Z	Y	R	Q
Factor	100	101	102	103	106	109	1012	1015	1018	1021	1024	1027	1030

Standard prefixes for the metric units of measure (submultiples)

Prefix name	N/A	deci	centi	milli	micro	nano	pico	femto	atto	zepto	yocto	ronto	quecto
Prefix symbol		d	c	m	μ	n	p	f	a	z	y	r	q
Factor	100	10−1	10−2	10−3	10−6	10−9	10−12	10−15	10−18	10−21	10−24	10−27	10−30

Non-SI units accepted for use with SI

Main article: non-SI units accepted for use with SI

Although, in theory, SI can be used for any physical measurement, it is recognized that some non-SI units still appear in the scientific, technical and commercial literature, and will continue to be used for many years to come. In addition, certain other units are so deeply embedded in the history and culture of the human race that they will continue to be used for the foreseeable future. The CIPM has catalogued a number of such non-SI units accepted for use with SI and published them in the SI Brochure thereby ensuring that their use is consistent across the globe. These units have been grouped as follows:

One litre, originally defined as being the volume of one kilogram of water at freezing point, was redefined in 1960 as being equivalent to this cube and has also been classed as a "Non-SI units accepted for use with the SI"
Since each side of the cube is 10 cm in length rather than one metre, the litre is not a coherent unit of measure with respect to SI.

• Non-SI units accepted for use with the SI (Table 6):

Certain units of time, angles and legacy non-SI metric units have a long history of consistent use. Most of mankind has used the day and its non-decimal subdivisions as a basis of time and, unlike the foot or the pound, these were the same regardless of where it was being measured. The radian, being ⁠1/2π⁠ of a revolution has mathematical niceties, but is cumbersome for navigation, and, as with time, the units used in navigation have a large degree of consistency around the world. The tonne, litre and hectare were adopted by the CGPM in 1879 and have been retained as units that may be used alongside SI units, having been given unique symbols. The catalogued units are

minute, hour, day, degree of arc, minute of arc, second of arc, hectare, litre and tonne

• Non-SI units whose values in SI units must be obtained experimentally (Table 7).

Physicists often use units of measure that are based on natural phenomena, particularly when the quantities associated with these phenomena are many orders of magnitude greater than or less than the equivalent SI unit. The most common ones have been catalogued in the SI brochure together with consistent symbols and accepted values, but with the caveat that their physical values need to be measured. :

electronvolt, dalton/unified atomic mass unit, astronomical unit, speed of light, Planck constant and electron mass

• Other non-SI units (Table 8):

A number of non-SI units that had never been formally sanctioned by the CGPM have continued to be used across the globe in many spheres including health care and navigation. As with the units of measure in Tables 6 and 7, these have been catalogued by the CIPM in the SI brochure to ensure consistent usage, but with the recommendation that authors who use them should define them wherever they are used.

bar, millimetre of mercury, ångström, nautical mile, barn, knot, neper and [deci]bel

• Non-SI units associated with the CGS and the CGS-Gaussian system of units (Table 9)

The SI manual also catalogues a number of legacy units of measure that are used in specific fields such as geodesy and geophysics or are found in the literature, particularly in classical and relativistic electrodynamics where thay have certain advantages: The units that are catalolgued are:

erg, dyne, poise, stokes, stilb, phot, gal, maxwell, gauss and œrsted.

Writing unit symbols and the values of quantities

Before 1948, the writing of metric quantities was haphazard. In 1879, the CIPM published recommendations for writing the symbols for length, area, volume, and mass, but it was outside its domain to publish recommendations for other quantities. Beginning in about 1900, physicists who had been using the symbol "μ" for "micrometre" (or "micron"), "λ" for "microlitre", and "γ" for "microgram" started to use the symbols "μm", "μL" and "μg", but it was only in 1935, a decade after the revision of the Metre Convention that the CIPM formally adopted this proposal and recommended that the symbol "μ" be used universally as a prefix for 10⁻⁶.

In 1948, the ninth CGPM approved the first formal recommendation for the writing of symbols in the metric system when the basis of the rules as they are now known was laid down. When, in 1960, the International System of Units was introduced, the rules that were put in place in 1948 were adapted for use with the new system. Since then the rules, apart from some minor modifications, have remained in place.

Writing the unit names

The CGPM rules state that the names of units follow the grammatical rules associated with common nouns: in English and in French they start with a lowercase letter (e.g., newton, hertz, pascal), even when the symbol for the unit begins with a capital letter. This also applies to "degrees Celsius", since "degree" is the unit. In German, however, the names of units, just like all German nouns, start with capital letters. The spelling of unit names is a matter for the guardians of the language concerned – the official British and American spellings for certain SI units differ – British English uses the spelling deca-, metre, and litre whereas American English uses the spelling deka-, meter, and liter, respectively.

Likewise, the plural form of units follow the grammar of the language concerned: in English, the normal rules of English grammar are used. e.g. "henries" is the plural of "henry". However the units lux, hertz, and siemens have irregular plurals in that they remain the same in both their singular and plural form.

In English, when unit names are combined to denote multiplication of the units concerned, they are separated with a hyphen or a space (e.g. newton-metre or newton metre). The plural is formed by converting the last unit name to the plural form (e.g. ten newton-metres).

Representation of SI units in Chinese and Japanese

Chinese expressway distances road sign in eastern Beijing. Although the primary text is in Chinese, the distances use the internationally recognised numerals and symbols.

Japanese and Chinese script use logograms rather than letters, and the rules for the writing unit names have been adapted to suit the languages.

In Japanese: Individual Kanji exist for some SI units, namely metre, litre, and gram, with the prefixes from kilo- (1000) to milli- (1/1000), yielding 21 (3×7) characters. These were created in Japan in the late 19th century (Meiji period) by choosing characters for the basic units – 米 "metre", 升 "litre", and 克 "gram" – and for the prefixes – 千 "kilo-, 1000", 百 "hecto-, 100", 十 "deca-, 10", 分 "deci-, 1/10", 厘 "centi-, 1/100", and 毛 "milli-, 1/1000" – and then combining them to form a single character, such as 粁 (米+千) for kilometre (in the case of no prefix, the base character alone is used). The entire metre series, for example, is 粁, 粨, 籵, 米, 粉, 糎, 粍.

In Chinese: The basic units are 米 mǐ "metre", 升 shēng "litre", 克 kè "gram", and 秒 mǐao "second". Some sample prefixes are 分 fēn "deci", 厘 lí "centi", 毫 háo "milli", and 微 wēi "micro". These are not combined into a single character, so for example centimetres are simply 厘米 límǐ.

The symbols for the metric units are internationally recognised Latin characters or, in respect of "Ω" or "μ", Greek characters.

Writing unit symbols and the values of quantities

Although the writing of unit names is language-specific, the writing of unit symbols and the values of quantities is consistent across all languages and as such the SI brochure has specific rules in respect of writing them. The guideline produced by NIST clarifies language-specific areas in respect of American English that were left open by the SI brochure, but is otherwise identical to the SI brochure.

General rules

General rules for writing SI units and quantities apply to text that is either hand-written or produced using an automated process:

• Symbols are mathematical entities, not abbreviations and as such do not have an appended period/full stop (.) unless the rules of grammar demand one for another reason such as denoting the end of a sentence.
• A prefix is part of the unit, and its symbol is prepended to the unit symbol without a separator (e.g., "k" in "km", "M" in "MPa", "G" in "GHz"). Compound prefixes are not allowed.
• Symbols for derived units formed by multiplication are joined with a centre dot (⋅) or a non-break space; e.g., N⋅m or N m.
• Symbols for derived units formed by division are joined with a solidus (/), or given as a negative exponent. E.g., the "metre per second" can be written m/s, m s⁻¹, m⋅s⁻¹, or ⁠m/s⁠. Only one solidus should be used; e.g., kg/(m⋅s²) and kg⋅m⁻¹⋅s⁻² are acceptable, but kg/m/s² is ambiguous and unacceptable.

Acceleration due to gravity.
Note the lower case letters (neither "metres" nor "seconds" were named after people), the space between the value and the units and the superscript "2" to denote "squared"

• The first letter of symbols for units derived from the name of a person is written in upper case, otherwise they are written in lower case. For example, the unit of pressure is named after Blaise Pascal, so its symbol is written "Pa" but the symbol for mole is written "mol". Thus "T" is the symbol for teslas, a measure of magnetic field strength and "t" the symbol for tonnes, a measure of mass. Since 1979 the litre may exceptionally be written using either an upper case "L" or a lower case "l", a decision prompted by the similarity of the lower case letter "l" to the numeral "1", especially with certain type-faces or English-style handwriting. The American National Institute of Standards and Technology recommends that within the United States "L" be used rather than "l".
• Symbols of units do not have a plural form; e.g., "25 kg", not "25 kgs".
• Upper-case and lower-case prefixes are not interchangeable – the quantities "1 mW" and "1 MW" represent two different quantities, the former is the typical power requirement of a hearing aid and the latter typical power requirement of a suburban train.
• The 10th resolution of CGPM in 2003 declared that "the symbol for the decimal marker shall be either the point on the line or the comma on the line." In practice, the decimal point is used in English-speaking countries and most of Asia, and the comma in most of Latin America and in continental European languages.
• Spaces should be used as a thousands separator (1000000) in contrast to commas or periods (1,000,000 or 1.000.000) in order to reduce confusion resulting from the variation between these forms in different countries.
• Any line-break inside a number, inside a compound unit, or between number and unit should be avoided. Where this is not possible, line breaks should coincide with thousands separators.
• Since the value of "billion" and "trillion" can vary from language to language, the dimensionless terms 'ppb' (parts per billion) and 'ppt' (parts per trillion) should be avoided. However, no alternative is suggested in the SI Brochure.

Printing SI symbols

Further rules are specified in respect of production of text using printing presses, word processors, typewriters and the like.

• Symbols are written in upright (Roman) type (m for metres, s for seconds), so as to differentiate from the italic type used for quantities (m for mass, s for displacement). By consensus of international standards bodies, this rule is applied independent of the font used for surrounding text.
• The value of a quantity is written as a number followed by a space (representing a multiplication sign) and a unit symbol; e.g., "2.21 kg", "7.3×10² m²", "22 K". This rule explicitly includes the per cent sign (%). Exceptions are the symbols for plane angular degrees, minutes and seconds (°, ′ and ″), which are placed immediately after the number with no intervening space.
• In Chinese, Japanese, and Korean language computing (CJK), some of the commonly used units, prefix-unit combinations, or unit-exponent combinations have been allocated predefined single characters taking up a full square. Unicode includes these in its CJK Compatibility and Letter like Symbols subranges for back compatibility, without necessarily recommending future usage. These are summarised in Unicode symbols. The cursive ℓ, a letter-like symbol, has been used in a number of countries in addition to China and Japan as a symbol for the litre but this is not currently recommended by any standards body.
• In print, the space used as a thousands separator (commonly called a thin space) is typically narrower than that used between words.

Realisation of units

A silicon sphere for the Avogadro project used for measuring the Avogadro constant to a relative uncertainty of 2×10⁻⁸ or less.

Metrologists carefully distinguish between the definition of a unit and its realisation. The definition of each base unit of the SI is drawn up so that it is unique and provides a sound theoretical basis on which the most accurate and reproducible measurements can be made. The realisation of the definition of a unit is the procedure by which the definition may be used to establish the value and associated uncertainty of a quantity of the same kind as the unit. A description of the practical realisation (French: Mise en pratique) of the base units are given in an electronic appendix to the SI brochure.

The published mise en pratique is not the only way in which a base unit can be determined: the SI brochure states that "any method consistent with the laws of physics could be used to realise any SI unit." In the current (2012) exercise to overhaul the definitions of the base units, various consultative committees of the CIPM have required that more than one mise en pratique shall be developed for determining the value of each unit. In particular:

• At least three separate experiments be carried out yielding values having a relative standard uncertainty in the determination of the kilogram of no more than 5×10⁻⁸ and at least one of these values should be better than 2×10⁻⁸. Both the Watt balance and the Avogadro project should be included in the experiments and any differences between these be reconciled.
• When determining the kelvin, the relative uncertainty of Boltzmann constant derived from two fundamentally different methods such as acoustic gas thermometry and dielectric constant gas thermometry be better than one part in 10⁻⁶ and that these values be corroborated by other measurements.

Post 1960 changes

The preamble to the Metre Convention read "Desiring the international uniformity and precision in standards of weight and measure, have resolved to conclude a convention ...". Changing technology has led to an evolution of the definitions and standards that has followed two principal strands - changes to SI itself and clarification of how to use units of measure that are not part of SI, but are still nevertheless used on a worldwide basis.

Changes to the SI

Since 1960 the CGPM has made a number of changes to SI. These include:

• The 13th CGPM (1967) renamed the "degree Kelvin" (symbol °K) to the "Kelvin" (symbol K)
• The 14th CGPM (1971) added the mole (symbol mol) to the list of base units.
• The 14th GCPM (1971) added the pascal (symbol Pa) for pressure and the siemens (symbol S) for electrical conductance to the list of named derived units.
• The 15th CGPM added the becquerel (symbol Bq) for "activity referred to a radionuclide" and the gray (symbol Gy) for ionizing radiation to the list of named derived units
• In order to distinguish between "absorbed dose" and "dose equivalent", the 16th CGPM added the sievert (symbol Sv) to the list of named derived units as the unit of dose equivalent.
• The 16th CGPM (1979) clarified that in a break with convention either the letter "L" or the letter "l" may be used as a symbol for the litre.

A sphygmomanometer - the traditional device that measures blood pressure using mercury in a manometer. Pressures are recorded in "millimetres of mercury"

• The 21st CGPM (1999) added the katal (symbol kat) for catalytic activity to the list of named derived units.
• In its original form (1960), the SI defined prefixes for values ranging from the pica (symbol p) having a value of 10⁻¹² to the tera (symbol T) having a value of 10¹². The list was extended at the 12th CGPM (1964), the 15th CGPM (1975) and at the 19th CGPM (1991) to give the current range of prefixes.

In addition, advantage was taken of developments in technology to redefine many of the base units enabling the use of higher precision techniques.

Retention of non-SI units

Although, in theory, SI can be used for any physical measurement, it is recognized that some non-SI units still appear in the scientific, technical and commercial literature, and will continue to be used for many years to come. In addition, certain other units are so deeply embedded in the history and culture of the human race that they will continue to be used for the foreseeable future. The CIPM has catalogued such units and included them in the SI brochure so that they can be used consistently.

The first such group are the units of time and of angles and certain legacy non-SI metric units. Most of mankind has used the day and its subdivisions as a basis of time with the result that the second, minute, hour and day, unlike the foot or the pound, were the same regardless of where it was being measured. The second has been catalogued as an SI unit, its multiples as units of measure that may be used alongside the SI. The measurement of angles has likewise had a long history of consistent use - the radian, being 1⁄2π of a revolution has mathematical niceties, but is cumbersome for navigation, hence the retention of the degree, minute and second of arc. The tonne, litre and hectare were adopted by the CGPM in 1879 and have been retained as units that may be used alongside SI units, having been given unique symbols.

Physicists often use units of measure that are based on natural phenomena such as the speed of light, the mass of a proton (approximately one dalton), the charge of an electron and the like. These too have been catalogued in the SI brochure with consistent symbols, but with the caveat that their physical values need to be measured.

In the interests of standardising health-related units of measure used in the nuclear industry, the 12th CGPM (1964) accepted the continued use of the curie (symbol Ci) as a non-SI unit of activity for radionuclides; the becquerel, sievert and gray were adopted in later years. Similarly, the millimetre of mercury (symbol mmHg) was retained for measuring blood pressure.

International trade

Main articles: Metrication in the United States and Metrication in the United Kingdom

One of the European Union's (EU) objectives is the creation of a single market for trade. To achieve this objective, the EU standardised on using SI as the legal units of measure. As of 2009, it has issued two units of measurement directives, which catalogued the units of measure that might be used for, amongst other things, trade: the first was Directive 71/354/EEC issued in 1971, which required member states to standardise on SI rather than use the variety of cgs and mks units then in use. The second was Directive 80/181/EEC issued in 1979, which replaced the first and gave the United Kingdom and the Republic of Ireland a number of derogations from the original directive.

The directives gave a derogation from using SI units in areas where other units of measure had either been agreed by international treaty, or were in universal use in worldwide trade. They also permitted the use of supplementary indicators alongside, but not in place of the units catalogued in the directive. In its original form, Directive 80/181/EEC had a cut-off date for the use of such indicators, but with each amendment this date was moved until, in 2009, supplementary indicators have been allowed indefinitely.

"New SI"

Main article: New SI definitions

Relations between proposed SI units definitions (in colour) and seven physical constants (in grey) with fixed numerical values in the proposed system.

When the metre was redefined in 1960, the kilogram was the only SI base unit that relied on a specific artefact. Moreover, after the 1996–1998 recalibration, a clear divergence between the various prototype kilograms was observed.

At its 23rd meeting (2007), the CGPM mandated the CIPM to investigate the use of natural constants as the basis for all units of measure rather than the artifacts that were then in use. At a meeting of the CCU held in Reading, United Kingdom in September 2010, a resolution and draft changes to the SI brochure that were to be presented to the next meeting of the CIPM in October 2010 were agreed to in principle. The proposals that the CCU put forward were:

• In addition to the speed of light, four constants of nature – Planck's constant, an elementary charge, Boltzmann constant and Avogadro's number – be defined to have exact values.
• The international prototype kilogram be retired
• The current definitions of the kilogram, ampere, kelvin and mole be revised.
• The wording of the definitions of all the base units be tightened up

The CIPM meeting of October 2010 found that "the conditions set by the General Conference at its 23rd meeting have not yet been fully met. For this reason the CIPM does not propose a revision of the SI at the present time". The CIPM did however sponsor a resolution at the 24th CGPM in which the changes were agreed in principle and which were expected to be finalised at the CGPM's next meeting in 2014.

See also

Dimensional analysis History of measurement International vocabulary of metrology ISO/IEC 80000 List of international common standards Long and short scales Names of large numbers Names of small numbers		Non-SI units mentioned in the SI Order of magnitude SI base unit SI derived unit Metric prefixes List of scientific units named after people
Organisations
Institute for Reference Materials and Measurements (IRMM)		CODATA
Standards and conventions
Coordinated Universal Time (UTC) ISO/IEC 80000		Unified Code for Units of Measure

References

• [SI Brochure] International Bureau of Weights and Measures (2006), The International System of Units (SI) (PDF) (8th ed.), ISBN 92-822-2213-6, archived (PDF) from the original on 4 June 2021, retrieved 16 December 2021
• [NIST 330] Thompson, Ambler; Taylor, Barry N. (2008). The International System of Units (SI) (Special publication 330) (PDF). Gaithersburg, MD: National Institute of Standards and Technology. Retrieved 18 June 2008.

• [NIST] Thompson, Ambler; Taylor, Barry N. (2008). Guide for the Use of the International System of Units (SI) (Special publication 811) (PDF). Gaithersburg, MD:: National Institute of Standards and Technology.{{cite book}}: CS1 maint: extra punctuation (link)

Further reading

• International Union of Pure and Applied Chemistry (1993). Quantities, Units and Symbols in Physical Chemistry, 2nd edition, Oxford: Blackwell Science. ISBN 0-632-03583-8. Electronic version.
• BW Petley (2004). Symbols, Units, Nomenclature, & Fundamental Physical Constants. IUPAP-39. [1]
• Unit Systems in Electromagnetism
• MW Keller et al. Metrology Triangle Using a Watt Balance, a Calculable Capacitor, and a Single-Electron Tunneling Device
• “The Current SI Seen From the Perspective of the Proposed New SI”. Barry N. Taylor. Journal of Research of the National Institute of Standards and Technology, Vol. 116, No. 6, Pgs. 797–807, Nov–Dec 2011.

External links

Official

• BIPM Bureau International des Poids et Mesures (SI maintenance agency) (home page)
  • BIPM brochure (SI reference)
• ISO 80000-1:2009 Quantities and units – Part 1: General
• NIST Official Publications
  • NIST Special Publication 330, 2008 Edition: The International System of Units (SI)
  • NIST Special Publication 811, 2008 Edition: Guide for the Use of the International System of Units
  • NIST Special Pub 814: Interpretation of the SI for the United States and Federal Government Metric Conversion Policy
• Weights and Measures Act, Canada
• IEEE/ASTM SI 10-2002 Standard for Use of the International System of Units (SI): The Modern Metric System (ANSI approved, joint IEEE/ASTM standard)
• Rules for SAE Use of SI (Metric) Units
• National Physical Laboratory, UK

Information

• ‹The template Curlie is being considered for deletion.› International System of Units at Curlie
• EngNet Metric Conversion Chart Online Categorised Metric Conversion Calculator
• U.S. Metric Association. 2008. A Practical Guide to the International System of Units

History

• LaTeX SIunits package manual gives a historical background to the SI system.

Research

• The metrological triangle
• Recommendation of ICWM 1 (CI-2005)

Pro-metric advocacy groups

• The UK Metric Association
• The US Metric Association
• Canadian Metric Association
• Metrication US

Pro-customary measures pressure groups

• ‹The template Curlie is being considered for deletion.› Pro-customary measures groups at Curlie