Jump to content

K1 tank

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by MikeTango (talk | contribs) at 09:10, 19 January 2023. The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

"K1A1" redirects here. For the rifle, see Daewoo Precision Industries K1.
K1
K1
TypeMain battle tank
Place of originSouth Korea
Service history
In service
  • K1: 1987–present
  • K1E1: 2014–present
  • K1A1: 2001–2023 (scheduled)
  • K1A2: 2013–present
Used bySee operators
Production history
Designer
Designed
  • K1: 1978–1984
  • K1A1: 1991–1996
Manufacturer
Unit cost
  • K1: ₩2.3 billion (1994)[1]
  • K1A1: ₩4.4 billion (2001)
  • K1A2: ₩6.0 billion
Produced
  • K1: 1987–1997
  • K1E1: 2014–present
  • K1A1: 1999–2010
  • K1A2: 2012–2023 (scheduled)
No. built
  • K1/E1: 1,027
  • K1A1/A2: 484
Specifications
Mass
Length
  • K1: 9.67 m (gun forward)
  • K1A1: 9.71 m (gun forward)
Width3.60 m
Height2.25 m
Crew4
Armor
Main
armament
  • K1: KM68A1 105 mm (47 rounds)
  • K1E1: KM68A1 105 mm (47 rounds)
  • K1A1: KM256 120 mm (32 rounds)
    WIA CN03 120 mm (32 rounds)
  • K1A2: WIA CN03 120 mm (32 rounds)
Secondary
armament
EngineSTX Engine/MTU Friedrichshafen MB871Ka-501 8-cylinder water-cooled turbocharged diesel engine
1200 hp (890 kW) @ 2600 rpm
Power/weight
  • K1: 23.4 hp/ton (17.44 kW/t)
  • K1A1: 22.5 hp/ton (16.77 kW/t)
  • K1A2: 22 hp/ton (16.40 kW/t)
TransmissionHyundai Transys/ZF Friedrichshafen LSG 3000
Automatic, 4 forward, 2 reverse
SuspensionHydropneumatic (wheel 1, 2, 6),
torsion bar (wheel 3, 4, 5)
Ground clearance
  • longitudinal slope: 60 %
  • lateral slope: 30 %
  • vertical: 1.1 m
  • trench: 2.74 m
  • fording: 1.2 m (without snorkel) or 2.2 m (with snorkel)
Operational
range
500 km (cruise)
Maximum speed
  • K1: 65 km/h (40 mph) (roads)
  • K1A1: 60 km/h (37 mph) (roads)
  • 40 km/h (25 mph) (cross-country)

The K1 is a South Korean main battle tank designed by Chrysler Defense (later General Dynamics Land Systems) and Hyundai Precision Industry (later Hyundai Rotem) for the Republic of Korea Armed Forces. The vehicle's design was based on Chrysler's M1 Abrams together with some proven subsystems from M60A3.[3] The K1A1 is an upgunned variant with a 120 mm 44 caliber smoothbore gun, and outfitted with more modern electronics, ballistic computers, fire control systems, and armor. Hyundai Rotem produced 1,511 K1 and K1A1 tanks between 1986 and 2010.

Development

K-1 combat firing practice, 1st Armored Brigade.

In the early 1970s, South Korea received an intelligence report about North Korea locally producing Soviet T-62 tanks. Meanwhile, the U.S. 7th Infantry Division began withdrawing from South Korea from 1969 to 1971 under the Nixon Doctrine. South Korean President Park Chung-hee requested the latest variant of M60 tanks to maintain the balance of power. However, the United States responded by transferring used M48 tanks and providing upgrades instead; South Korea received 25 M48A5s from the United States Forces Korea and numerous M48A3s that were used, but in good condition, during the Vietnam War.[4]

Under the agreement, South Korea received the technical data package (TDP) of M48 Patton and its upgrade kits for 12 major enhancements. Korean engineers were sent to the United States Army Depot in Alabama for training such as armor cast steel wielding and production, precision manufacturing, assembling skills, quality inspection, and test evaluation. Around the same time, Park Chung-hee ordered to develop a domestic tank and personally summoned Chung Ju-yung, the founder of Hyundai Group, to recommend building a tank factory. Chung Ju-yung, thinking that the president asked for a train factory, promised to build one.[note 1] The chairman was shocked after learning about his misunderstanding from the secretary as he was leaving the building.[4][5]

Not satisfied with M48 Patton upgrade, South Korea began looking for a new tank that could overwhelm every North Korean counterpart as the existence of T-62 and its manufacturing facility were confirmed by satellite images in 1976. South Korea first asked Chrysler Defense for a solution to acquire a better tank, and Chrysler suggested the purchasing M60A3 or producing it in South Korea. Because the American offer was an outdated design, South Korea then contacted KraussMaffei of West Germany to receive technology assistance, which KraussMaffei offered a unique tank design based on Leopard 1. Both South Korea and West Germany kept the cooperation in secret, because the two nations believed that the United States would intervene once the information leaks. In 1977, as expected, Chrysler Defense showed interest in the Korean tank project after its engineers became available and wanted to generate more profit after the development of M1 Abrams. This time, Chrysler offered a new tank based on the newest M1 Abrams. Eventually, the American design was chosen, and a memorandum of understanding (MOU) was signed on 6 July 1978 to supply two prototypes, and the executive contract was signed on 1 December 1978.[3][4][5][6]

Between 1979 and 1980, several MOUs were signed between the two nations, mostly regarding intellectual rights and royalty payments. According to the MOU, the United States will provide its state-of-art Special Armor Package (SAP), in which the material and protection is identical to M1 Abrams, while limiting Koreans from access until the installation due to national security reasons. Exporting of K1 is strictly controlled and needs authorization from the United States as many sensitive systems are installed, and South Korea requires to pay royalty to Chrysler Defense. Also, 44 designated parts (gradually reduced to 14) cannot be changed without United States approval, and some parts must be purchased periodically. In addition, South Korea will have the rights on, and limited to, the technologies developed uniquely with the money provided by South Korea, while Chrysler also claims the rights to use in the future. On the other hand, South Korea benefitted on the development cost from the cooperation with Chrysler; South Korea paid $60 million for the prototype development, far below than $700 million spent on M1 Abrams. However, Hyundai Precision Industry, which planned to produce the tank at its new factory, was excluded from direct involvement in designing the tank, and it was the biggest problem since Koreans had never produced tanks before. Under these conditions, Koreans will be unable to produce tanks as they do not understand the structure and technology of the tank even with prototypes in hand.[3]

From October 1980 to April 1981, Chrysler had three meetings with Hyundai to confirm the required operational capability (ROC), and presented a small scale mock-up along with reports. During the production of the prototypes, Chrysler Defense was sold to General Dynamics Land Systems (GDLS) in March 1982. A total of 2 prototypes named ROKIT (Republic of Korea Indigenous Tank) were produced with designations PV-1 (MTR - mobility test rig) and PV-2 (FTR - firepower test rig) in 1983 after 3 years of the development, and went trial at Aberdeen Proving Ground based on American military standards. During the trial, PV-1 failed to climb longitudinal slope of 60%, experienced fire on 1,200 hp Teledyne Continental Motors AVCR-1790 engine, and had issues on its transmission. PV-2 also reported issues with its fire control system; LOS (line of sight) was shaking due to frost in winter season, taking too long for warmup, interference from electromagnetic waves, and lockup of the ballistic computer. Protection tests were done on separately built ballistic hull and turret, which showed some flaws during the test. Eventually, the known problems were fixed and improved by the time of delivery of the two prototypes. At the end, GDLS transferred the PV-1 along with 1,370 pages of blueprints and the TDP, but the number of blueprints was insufficient for manufacturing.[5][6]

During the trial, a team of Korean engineers from Hyundai Precision Industry was dispatched to join Chrysler's developer team to look over the progress. Although the contract limits technological access to Koreans, engineers from both nations freely shared information during friendship interactions including a classified specification of M1 Abrams. When the upper management of Chrysler found out about this, they built a wall in the office to prevent information leakage. However, Koreans managed to obtain significant data during their 3 years of presence at the facility. In addition, the manufacturing team of Hyundai came for a tour to the American tank factory to understand how to build a tank factory. Koreans could only go to the specified path, but they memorized types of machineries and calculated the required sizes of the facility by counting the footsteps, which helped them to build the new factory at Changwon.[5][6]

In 1983, Hyundai accepted GDLS' new offer, and acquired special welding of armor plates, assembly of major devices, and weapon testing technologies. 30 engineers from GDLS were also sent to Korea, and participated in producing and testing preproduction models. From September 1984 to August 1985, a total of 5 XK1s were completed (2 for the Agency for Defense Development, 2 for the ROK Army, and 1 for the Army logistics), and went for further testing in South Korea. However, Hyundai realized that GDLS had made a crucial mistake by providing outdated blueprints that did not reflect the latest fixes, and XK1s began to experience the same issues they saw from early prototypes. In addition, the lack of detailed blueprints forced Korean engineers to rework the tank and create 5 thousands design changes and 10 thousands pages of blueprints. The biggest change during this process was the switching of the mobility system from American to German, in which the design change was done by GDLS. The air-cooled AVCR-1790 had lower torque thus unable to drive at high incline angles, and also experienced fire several times, which contributed to unexpected fire tests that proved survivability of the tank. For this reason, the MTU Friedrichshafen MB871Ka-501 water-cooled engine and the ZF Friedrichshafen LSG 3000 transmission were chosen for the new power pack.[6][7][8] These preproduction variants entered service with South Korean military in February 1986.[5][9]

On the other hand, Hughes' GPSS (Gunner's Primary Sight System) continuously saw issues with low accuracy and operational uses, while Hughes forced South Koreans to give up localization of the GPSS by doubling up the price when licensing. GDLS, which acquired Hughes in 1985, revealed that the system uses parts from Canada, West Germany, and Switzerland, and thus requires time-consuming multi-national cooperation in order to solve to problem. In 1986, another contract was signed between Hyundai and GDLS for updating the GPSS, increasing the cost of the gunner's sight, and this unsatisfactory lead South Koreans to look for alternative options immediately. In April 1987, the K1 tank test evaluation for conditional mass production was completed, and serial production began in September 1987. On 18 September, the tank was given the nickname 88-Tank by South Korean president Chun Doo-hwan to celebrate upcoming 1988 Summer Olympics.[5][6][7][10][11][12]

A total of 1,027 K1s were produced between 1986 and 1997 in 3 batches with design changes on each batch. Since 1995, the K1s received their first depot maintenance at Hyundai Precision Industry in the order of production (10 year cycle). The work includes the application of 3rd batch updates on the earlier produced vehicles.[5][13]

General characteristics

The K1 retains most of the features of the M1 Abrams, but also shows differences. Its main armament is a licensed M68A1 105 mm 52 caliber tank gun under designation KM68A1 by Hyundai Precision Industry, and carries 47 rounds of ammunitions at the hull and turret as it lacks bustle storage in the rear of the turret, which is filled with radio systems. The main gun is assisted by 16-bit fire control system and digital ballistic calculator. The tank has either M2 Browning or SNT Dynamics K6 12.7x99 mm NATO on commander's hatch mount, a M60D 7.62×51mm NATO machine gun on loader's hatch mount, and a M60E2-1 7.62×51mm NATO coaxial machine gun for gunner as secondary armaments.[14][15]

The K1 has size of 9.67 m (length with gun forward) x 3.60 m (width) x 2.25 m (height), and weighs 51.1 t or 51.5 t.[15] It is powered by German power pack consisting 1,200 hp (23.5 hp/t) from MTU Friedrichshafen MB871Ka-501 8-cylinder water-cooled turbocharged diesel engine licensed by Ssangyong Heavy Industries (now STX Engine) and ZF Friedrichshafen LSG 3000 transmission licensed by Hyundai Precision Industry (now Hyundai Transys). The tank can drive at a maximum speed of 65 km on paved roads and 40 km on cross-country with 500 km cruising range. Its chassis uses hybrid suspension combining hydropneumatic suspension on wheels 1, 2, and 6 and torsion bar on wheels 3, 4, and 5. It allows the tank to use kneeling to supplement the depression of the main gun, which is limited by the small sized turret, to minus 10 degrees, and provides crew comfortability on rough terrains.[7][8][14][15][16] For comparison, M1 Abrams is 9.77 m x 3.66 m x 2.37 m, and weighs 54 t.

The Gun/Turret Drive and Stabilization System (GTDSS) measures and compensates yawing and pitching, which occur on uneven and curved roads for gun turret to be capable of the precise fire while running. The GTDSS consists elevation servo system, elevation drive system, reference gyro, traverse servo system, traverse drive system, feed-forward gyro, electronic unit for gun and turret drive, and steering handle for artillery man. The system is locally produced in South Korea by Dongmyeong Heavy Industries (now Mottrol) since 1992.[17]

The gunner's sight was initially a problematic Hughes GPSS, which uses a Nd:YAG laser rangefinder, a similar model used for the M1 Abrams. Despite Koreans having decided to upgrade the existing GPSS, Samsung Electronics signed a deal with Texas Instruments to supply and locally produce the GPTTS (Gunner's Primary Tank Thermal Sight) in 1986. Hyundai originally planned to install GPTTS in 1987, but serious problems such as a failure of the laser rangefinder forced Hyundai to postpone the plan. Due to the delays, a total of 445 K1s were manufactured with imported Hughes GPSS until 1991. Meantime, after failing to repair the GPTTS, Texas Instruments gave access to technology to the Agency for Defense Development. Within a year, a combined team managed to fix the sight and further improve it by increasing the sight's distance from 2 km to 3 km. Samsung Electronics began supplying the GPTTS in 1991. Later, during the parliamentary investigation, it was found that there were lobbies involved in selecting the GPTTS, leading to a selection of the product without proper testing, which caused an additional development cost of 16 billion KRW on the sight. Regardless of the involvement of lobbies, upgraded GPTTS showed superior performance when shooting the hidden target behind the smoke screen, which the GPSS failed to do so during the test on 2 September 1993. The GPTTS uses a carbon dioxide laser range finder, which is safer to the human eye upon being hit by the laser, while Nd:YAG can blind the victim. However, the GPTTS was a complex and heavier system. Ironically, access to GPTTS technology enabled Koreans to design their own gunner's sight. The ADD began the research in 1992 for domestic gunner's sight (later known as KGPS: Korean Gunner's Primary Sight) using the Raman laser believing such technology would be used for future weapon systems. In 1995, by the time Koreans were at the end stage of development, Europe announced it would use Raman lasers for tanks followed by the United States.[12][18][19][20][21]

The commander's sight is from SFIM (now SAGEM) of France, and it has a hunter killer ability that allows tank crews to engage multiple targets at once by allowing the commander to search 360 degrees and direct the main gun.[7][12][14] The hunter killer feature was a major difference compared to the M1 Abrams, which becomes available on later M1A2 upgrades. The commander's sight was not, however, equipped with light amplification or thermal optics, which led to the commander to rely on personal night vision goggles for night operation, while the gunner's sight was equipped with a thermal observation device, which meant that the K1 had superior sensors until the introduction of the M1A2.

The Special Armor Package (SAP) is a classified composite armor used for the K1 tanks crafted by the United States using identical materials and technologies used on the armor of M1 Abrams. Its specifications are strictly restricted for public release, and limits South Koreans from accessing the armor. The SAP is applied on the turret and the front of the hull. Meanwhile, the side of the hull is protected with additional RHA plates, which provide protection to all types of 115 mm ammunition fired from T-62 in the hands of North Korea by the time of the development.[7] According to the media report, frontal armor of the K1 baseline is between 400 and 500 mm against KE projectiles.[22] Smoke grenade launchers are located on each outer side of the turret front. The vehicle is also equipped with a fire-extinguishing system in the engine room, where the system notifies crews to activate automatic extinguishers when a thermometer detects a critical temperature.[14] The extinguishant used is Halon1301, commonly used by western main battle tanks. The vehicle lacks an overpressure system for CBRN defense, thus requires tank crews to wear personal protective gears to operate in chemical, biological, radiological and nuclear warfare environments.

Operational history

On 19 June 1995, the United States and South Korea agreed in exporting of the K1 to third countries during the defense talks. Hyundai Precision Industry planned to sell 70 tanks to Malaysia. The price of the K1 was increased to $2.8 billion KRW in 1995.[note 2][23][24][25] The K1 was displayed in Malaysia at DSA 1996 on 23–26 April 1996.[26][27] To suit the jungle environment of Malaysia, Hyundai suggested a 47.9 t variant K1M based on the K1; the tank carries a total of 41 rounds, and is equipped with KGPS for the gunner's sight and overpressure device for CBRN protection. The K1 competed against Polish PT-91 Twardy of Bumar-Labedy and Ukrainian T-84 of KMDB. Initially, the K1 was favored by Malaysia, but the high price and Malaysia's economic crisis caused by the 1997 Asian financial crisis led to selection of Polish PT-91.[28][29][13]

On 7 June 1999, Hyundai Precision Industry announced to co-develop K1 tank simulator for weaponry with the ADD to lower the training cost.[30] On 19 February 2001, Hyundai Mobis (formerly Hyundai Precision Industry) announced that the simulator was completed and supplied to the military on 19 February 2001. Simulators are expected to decrease training costs from 20 billion KRW to 1.4 billion KRW per 1,000 trainees every year.[31]

On 28 October 1999, Samsung Electronics and Thomson-CSF agreed to create a joint venture with each company investing and holding 50% of the shares. Thomson-CSF will receive technology transfer of Samsung's defense products such as communication equipment, satellite communication systems and terminals, fire control system, detection and tracking devices, radar guidance equipment, and gunner's sight (KGPS), while Samsung will gain access to Thomson-CSF's network for overseas exports.[32] In February 2000, Samsung Thomson-CSF was created, and it was renamed to Samsung Thales on 26 February 2001.[33]

On 27 February 2003, Ssang Yong Information and the ADD developed an IETM (interactive electronic technical manual) in four CD-ROMs that contain twenty books of technical manual for the K1A1 using domestically developed software for the first time.[34] On 26 September, the ADD announced the development of insensitive gunpower that does not explode in shock, fire, or heat that can occur in the transport, storage, and operation of warheads and ammunition.[35]

On 21 October 2004, it was revealed that South Korea was developing depleted uranium tank munitions between 1983 to 1987. South Korea eventually halted the development after the United States learned about the project in 1987.[36]

On 6 August 2010, during a live firing exercise at Paju, a round exploded in the barrel of a K1's 105 mm gun, destroying the gun, but leaving crew uninjured. This was reported to be the latest in a series of such accidents since the K1 entered service.[37]

In December 2020, the Agency for Defense Development (ADD) commenced a program to develop unmanned versions of the K1 tank and K9 Thunder. Hyundai Rotem was contracted to develop the unmanned tank by 2024.[38][39]

K1A1

K1A1 tanks of the 20th Mechanized Infantry Division of ROK Army is maneuvering through rough terrain.

In 1985, South Korea exercised for K1 upgrade plan report, which was included in the previous contract. GDLS responded with an upgraded model with a 120 mm smoothbore gun similar to M1A1 Abrams. In the late 1980s, South Korea received multiple intelligence reports about North Korea purchasing T-72 tanks, which had a 125 mm smoothbore cannon. The intelligence report turned out to be false decades later. However, it alerted South Korea at that time as a 125 mm smoothbore could fire from a farther distance and have higher penetration compared to a 105 mm rifled cannon. Therefore, South Korean government requested the ADD to make a new tank equipped with a 120 mm cannon. In 1988, the ADD launched exploration development, and began official system development with Hyundai Precision Industry in 1991.[14][40]

The ADD and Hyundai submitted a plan to redesign the tank by replacing most parts with the latest technology. However, the plan was rejected by the military as such an upgrade would require a budget over the limit, and too luxurious for a conscription army. Therefore, the ADD and Hyundai changed the plan by focusing on the weaponry by increasing the caliber to 120 mm. Since South Korea does not know the specification of 120 mm cannon, it decided to compare the cannons from the United States, Germany, France, and Israel, while ammunition was competed between the United States, which was a German design, and Israel. On 10 March 1994, Poongsan Corporation was selected as the main supplier of the 120 mm tank ammunition. In September 1994, despite Israeli IMI 120 mm gun showed better performance, easier logistics access made South Korea to license produce American M256 120 mm smoothbore, which was based on German Rheinmetall Rh-120, as designation KM256. Meanwhile, on October 10, 1996, ADD announced that it would develop domestic 120mm ammunition without receiving technology transfer from foreign countries.[40][41][42][43][44]

On 7 October 1994, the ADD reported at the parliamentary inspection that the KGPS, fitted with a Raman laser rangefinder, was tested on the K1 and showed good performances. It is expected to be tested on an upgraded prototype in 1996.[45]

The delivery ceremony of the K1A1 prototype was held on 3 April 1996. The major improvement was firepower, which was increased from 300 mm penetration at 1.2 km to 600 mm penetration at 2 km. South Korea expects to mass-produce K1A1 in 1997.[46] On 9 October, the ADD announced the development of the KGPS, which was developed by the technologies gained during the GPTTS upgrades.[12][47]

On 9 June 1998, the Ministry of Defense announced that mass production of K1A1 would begin in 1999, 2 years behind schedule due to 1997 Asian financial crisis that decreased the defense budget.[48][49] On 15 November 1999, Hyundai Precision Industry signed an estimate of 1 trillion KRW contract to produce K1A1.[50] The first K1A1 release ceremony was held on 12 October 2001. The tank weighs 53.2 t and has a length of 9.71 m (gun forward), and each tank costs 4.4 billion KRW.[51]

Unlike the K1, the newly upgraded design was made only by Korean engineers. Originally, GDLS wanted to participate in the K1 series to maintain its level of influence, and it proposed a partnership for the project due to concerns about Koreans lacking such skills. However, South Korean engineers declined the offer, and decided to take full responsibility on the project even if it fails, because they could learn about the main battle tank throughout the process and to maximize localization by reducing the technological reliance from GDLS. In the end, GDLS transferred the TDP, and sent a small team of engineers to South Korea for a 50 man-day contract, but the contract was never needed.[14][40]

Despite the similar look, the K1A1 is made of completely different materials and carries more advanced subsystems.[14][40] The K1A1 can easily be distinguished from the K1 by the shape of the gun, location of the co-axial machinegun, shape of the commander's sight, and overall angular shape of the turret (the K1A1 has more curved surfaces than the K1). The 120 mm smoothbore gun of K1A1 is thicker than the K1's 105 mm rifled gun and has a thicker thermal sleeve a third of the way from the base of the gun. The co-axial machinegun on K1A1 is located at a much higher point compared to the K1. The K1A1 also features a somewhat cone-shaped day/night KGPS compared to day-only sight of the K1, which has a plain, tube-like appearance to it.

K1 & K1A1 comparison
Variants K1 (early) K1 (late) K1A1
Main gun KM68A1 105 mm rifled (47 rounds) KM256 120 mm smoothbore (32 rounds)
Firepower (estimate) 300 mm penetration at 1.2 km 600 mm penetration at 2 km
Commander's sight from SFIM KCPS
Gunner's sight GPSS GPTTS KGPS
Protection (estimate) SAP 400–500 mm vs KE KSAP 600 mm vs KE
Weight 51.1 t 51.5 t 53.2 t
Maximum speed 65 km/h 60 km/h

Firepower

K1A1 in firing exercise.

The most important upgrade was switching the main gun from a 105 mm KM68A1 rifled (47 rounds) to a 120 mm KM256 smoothbore (32 rounds), which is produced under license by Hyundai Precision Industry (now Hyundai WIA), mounted on the domestically upgraded turret.[40] In addition, South Korea began to deploy K276 120 mm armour-piercing fin-stabilized discarding sabot (APFSDS) ammunition with the most sophisticated tungsten heavy alloy penetrators during that time, created after several technological breakthroughs that were new to the world. Benefitted by domestic tungsten processing technologies from abundant deposits, Korean engineers invented self-sharpening process on the tungsten heavy alloy, which the process was only achievable from depleted uranium (DU) penetrators, by applying microstructure control and multi-stage heat treatment after 4 years of development between in 1990 to 1993 with 1.1 billion KRW budget. Most penetrators in the world receive a single heat treatment, while Korean penetrators are treated 20 times using the new technology, which increases impact toughness by 300%. The self-sharpening effect increases penetration by 8–16% compared to regular penetrators, and compensates 6–10% less penetration from material disadvantage against DU, providing firepower of that of DU ammunition in a DU particles-free environment. South Korea holds related patents on 6 other nations,[note 3] and the technology was on the U.S. Army Master Plan in 1997 and 1998 as a technology to acquire from outside the United States.[14][52]

Electronics and sensors

The systems were upgraded from 16-bit to 32-bit, and were designed using upgraded computers including 32-bit digital ballistic calculators.[53]

The new gunner's sight KGPS consists of a stabilization device that allows better accuracy for aiming and shooting during maneuvers, a thermal imaging device and a daytime optical device for day and night observation, and a laser rangefinder that measures the range of the captured target. The sharpness and magnification of the thermal imager and daytime optical system have been increased, making it possible to observe and identify the target from a greater distance. In particular, the screen display method of the thermal imager has been improved for enhanced night combat capability. The laser rangefinder uses an eye-safe Raman laser, which gives excellent distance measurement ability while providing crew safety during crew training. In addition, the sight has a recording feature for the gunner to check the location of the aiming point during actual shooting or non-shooting training, enhancing the training effect and verifying the results. The thermal imaging device can be operated independently for convenience, thus allowing the tank to shoot even in the event of a malfunction of the thermal. The daytime optical system image is displayed in natural color, making it convenient to observe. The power consumption is reduced by about 40% compared to the previous model, which increases operational time with the engine off to maximize stealth kill.[12][47][40] It has a daytime magnification of 1 to 10 times, and a far-infrared thermal magnification of 3 to 10 times.[52]

The new commander's sight KCPS (Korean Commander's Panoramic Sight) was developed in 1999 and has a thermal sight for night operation.[54] However, both KGPS and KCPS heavily rely on foreign parts and were reported to have an average localization rate of 27.6% in the year 2004.[55]

Protection

The SAP was changed to a more protective Korean Special Armor Plate (KSAP)[56] as well as switching American RHA to Korean domestic armor steel.[57] Although the exact specification is classified, it was reported that the KSAP provides a protection level of 600 mm against KE ammunition for the frontal armor.[22][40] In addition, the exterior of the K1A1 has nuts that were not seen on the K1, hinting a structural difference from previous version. This is different from the way Americans installed and welded SAP directly to prevent Koreans from technically accessing the armor during the K1 production.[58][59][60][note 4] Moreover, a captain of the ROK Army Armor School mentioned about the combination of explosive reactive armor (ERA) with composite material being used for the armor of K1A1.[61] In 1996, South Korea acquired 1,250 hp variant Russian domestic specification T-80Us along with Kontakt-5 ERAs, and T-80Us contributed in developing Korean domestic ERAs and enhancing armor technology.[62][63] Therefore, based on the available sources, K1A1 is fitted with domestic armor, in which the technology has influence from American M1 Abrams and Russian T-80U, and ERAs are located behind the outer shell of the tank.

Mobility

Both the torsion bar and hydropneumatic suspension were enhanced to withstand the recoil of the new 120 mm cannon. The vehicle can move at a speed of 60–65 km/h.[14][40]

Variants and upgrades

A K1 88-Tank disembarks from a U.S. Navy Landing Craft Air Cushion during RSOI/Foal Eagle 2004.
The K1 ARV being in use when replacing a tank engine
  • ROKIT: Acronym for the Republic of Korea Indigenous Tank. Experimental prototype by Chrysler Defense. 2 vehicles (PV-1 and PV-2) were produced.
  • XK1: Preproduction prototype by Hyundai Precision Industry. 5 vehicles were produced, and entered service in 1986.
  • K1: First production variant. 1,027 units built between 1987 and 1997 (445 with GPSS and 582 with GPTTS) in 3 batches. To be upgraded to K1E1 by 2026.
    • K1M: Proposed export variant for Malaysia.
    • K1 PIP: Upgraded K1.
      • K1E1: Further upgraded K1. Production began in December 2013, and the first K1E1 rolled out on 7 July 2014. The upgrade will be similar to that of K1A2. All K1 will be upgraded to K1E1 by 2026.[64] The name was inherited from the K1A1 prototype, the K1E1.[65]
      • K1E2: As of August 2018, the K1E2 type is planned to be improved. It is expected to be upgraded to a large-scale repair (renovation) in 2024. The main improvement point is the replacement of the new armored upgrading of the protection, installation of the positive pressure device, acceleration of 10% upgrade (1200 hp engine to 1320 hp) or change 1500 hp engine, Introduction of RWS, etc.[66]
  • K1A1: First major enhanced variant. 484 units built between 1999 and 2010 in 2 batches.[67] To be upgraded to K1A2 by 2023.
    • K1A2: Upgraded K1A1. Originally named as K1A1 PIP. Developed from 2008 to 2010, and mass-production started in 2012. First upgraded vehicle was rolled out on 20 December 2013. Technology benefit from K2 Black Panther has been applied to this model. It features additional systems such as a digital battlefield control system, IFFS, and front and rear surveillance cameras. With its improved real-time information sharing, inter-combat vehicle operation, friendly fire prevention and driver operability. All K1A1 will be upgraded to K1A2 by 2022.[64][65]
  • K1 ARV: The K1 Armored Recovery Vehicle is based on the K1 tank. It has a crane, winch and dozer system built on the vehicle.[68] It was developed with assistance from Krupp Maschinenbau Kiel GmbH (now Rheinmetall Landsysteme GmbH) between 1988 and 1992, with first deployment in 1993.[68]
  • K1 AVLB: The K1 Armoured Vehicle-Launched Bridge variant uses a scissor-type bridge system mounted on the chassis. It was developed from 1988 to 1992 with help from Vickers Defense Systems.[69]
  • K600 CEV: The K1 Combat Engineer Vehicle is based on the K1A1/A2 chassis, mounting a mine plough, an excavator arm on the right side, and a lane marking system. Development is expected to be completed in June 2018 and begin production in 2019.[70]

Operators

Map of operators of K1 or its variants
 South Korea
Received 1,027 K1 between 1987 to 1997, and 484 K1A1 between 1999 to 2010.[13] All K1/K1A1 are being upgraded to K1E1/K1A2 variants.

See also

Notes

  1. ^ Korean word tank and train are written and spoken exactly the same: 전차 (jeoncha). Only difference is their Hanja: tank (戰車) vs train (電車)
  2. ^ Presumably batch 3 price.
  3. ^ Japan, United Kingdom, United States, and 3 other unspecified nations.
  4. ^ Later produced batch of the K1 also shows nuts on the exterior, but there is no direct evidence of changing armor type.

References

  1. ^ "北韓무력부 독자적 軍예산 편성". Yonhap News Agency. 21 July 1994. Archived from the original on 24 December 2022. Retrieved 24 December 2022.
  2. ^ "K1A1 Main Battle Tank(MBT)" (PDF). Hyundai Rotem. Archived from the original (PDF) on 21 March 2012. Retrieved 31 January 2012.
  3. ^ a b c Defense Media Agency (17 January 2016). "[첨단국가의 초석, 방위산업] 한국형 전차 K1 개발사 ①". 국방TV. Archived from the original on 11 December 2022. Retrieved 11 December 2022.
  4. ^ a b c Defense Media Agency (15 January 2016). "[첨단국가의 초석, 방위산업] 한국형 전차 개발의 씨앗, M48 개조사업". 국방TV. Archived from the original on 24 December 2022. Retrieved 24 December 2022.
  5. ^ a b c d e f g Korea Defense Industry Association (1 May 1998). "방산업체 소개-자주 국방의 선봉 현대정공(주)" (PDF). Defense and Technology (국방과기술). Archived from the original (PDF) on 27 September 2022. Retrieved 27 September 2022.
  6. ^ a b c d e Defense Media Agency (17 January 2016). "[첨단국가의 초석, 방위산업] 한국형 전차 K1 개발사 ②". 국방TV. Archived from the original on 11 December 2022. Retrieved 11 December 2022.
  7. ^ a b c d e Defense Media Agency (17 September 2016). "[첨단국가의 초석, 방위산업] 한국형 전차 K1 개발사 ③". 국방TV. Archived from the original on 25 September 2022. Retrieved 25 September 2022.
  8. ^ a b Shin In-ho (20 April 2020). "K1 주력전차". Kookbangilbo. Archived from the original on 24 December 2022. Retrieved 24 December 2022.
  9. ^ Kim Jeong-tae (23 December 2002). "[기업] 로템 연말 군부대 위문 방문". Money Today. Archived from the original on 28 September 2022. Retrieved 28 September 2022.
  10. ^ Oh Dong-ryong (10 October 2008). "차세대 戰車 '흑표' 생산하는 현대로템". The Chosun Ilbo. Archived from the original on 20 September 2022. Retrieved 20 September 2022.
  11. ^ Yoon Jong-bo (18 September 1987). "전두환 대통령 한국형 88전차 명명식[윤종보]". MBC. Archived from the original on 29 November 2020. Retrieved 29 November 2020.
  12. ^ a b c d e Kim Gwan-yong (23 April 2016). "[e-무기]미국산 불량품 고치다 탄생한 한국형 전차의 '눈'". Edaily. Archived from the original on 22 May 2022. Retrieved 22 May 2022.
  13. ^ a b c "방산수출 지원과 정부기관 간 약정". Kookbang Ilbo. 16 November 2020. Archived from the original on 24 December 2022. Retrieved 24 December 2022.
  14. ^ a b c d e f g h i "지상전의 왕자 K1A1전차". Defense Media Agency. 21 July 2009. Archived from the original on 21 September 2022. Retrieved 21 September 2022.
  15. ^ a b c "지상전투의 핵심 한국형 K-1 전차" (PDF). Korea Defense Industry Association. 1 May 1995. pp. 8–9. ISSN 1227-1705. Archived from the original (PDF) on 23 September 2022. Retrieved 23 September 2022.
  16. ^ Kim Dong-Jin (1 May 1991). "전차의 소개와 발전추세(1)" (PDF). Korea Defense Industry Association. pp. 80–86. ISSN 1227-1705. Archived from the original (PDF) on 23 September 2022. Retrieved 23 September 2022.
  17. ^ "Defense Applications & Solutions" (PDF). Mottrol. Archived from the original (PDF) on 30 December 2022. Retrieved 30 December 2022. p. 5
  18. ^ Park Je-wan (8 October 2020). "[단독 / 레이더P] 육군 주력전차 10대중 2대 포수조준경 고장…부품 없어 최장 8년 무력화". Maeil Business Newspaper. Archived from the original on 7 January 2023. Retrieved 7 January 2023.
  19. ^ "육군납품 포수조준경 GPTTS 제품성능 문제없다...삼성전자". Korea Economic Daily. 6 September 1993. Archived from the original on 7 January 2023. Retrieved 7 January 2023.
  20. ^ "<焦點> 國監 쟁점 상위위-1". Yonhap News Agency. 10 October 1994. Archived from the original on 24 August 2022. Retrieved 24 August 2022.
  21. ^ "國會 국정감사 계속(종합)". Yonhap News Agency. 7 October 1994. Archived from the original on 24 August 2022. Retrieved 24 August 2022.
  22. ^ a b Yoon Hee-hoon (10 October 2016). "[방산 현장을 가다]⑥ 명품 전차 반열에 우뚝 'K2'... 현대로템을 가다". Chosun Biz. Archived from the original on 11 October 2016. Retrieved 11 October 2016.
  23. ^ "한국형 K-1전차, 제3국 수출 합의". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  24. ^ "현대정공 K-1전차 수출 추진". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  25. ^ 成耆洪기자. ""방산업체 高價무기 수출 3년간 전무"". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  26. ^ "말레이시아 防産전시회에 한국관설치". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  27. ^ 기자, 文炳勳. "한국의 방위산업". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  28. ^ 기자, 金昌會. "대외경제조정위원회 개최". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  29. ^ 鄭鶴九기자. "국감현장-국방위". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  30. ^ 이경욱기자. "현대정공, 전차포술 모의훈련장비 개발 착수". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  31. ^ "[거래소] 현대모비스 "전차 포술 모의훈련기 개발·납품"". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  32. ^ 박상현기자. "삼성전자-톰슨, 방산 합작계약". n.news.naver.com (in Korean). Retrieved 2022-09-24.
  33. ^ "[인터뷰] 박태진 삼성탈레스 사장". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  34. ^ "쌍용정보, 국방 기술교범 디지털화 SW 개발". n.news.naver.com (in Korean). Retrieved 2022-09-26.
  35. ^ "차기전차용 열상센서.둔감화약 개발". n.news.naver.com (in Korean). Retrieved 2022-09-26.
  36. ^ 권박효원. ""원자력연, 80년대 열화우라늄탄 개발"". n.news.naver.com (in Korean). Retrieved 2022-12-04.
  37. ^ "Main gun on K1 tank explodes during live fire drill". Yonhap News Agency. 6 September 2010. Archived from the original on 26 March 2012. Retrieved 8 September 2010.
  38. ^ Kim, Dae Y. (11 August 2020). "South Korea to develop unmanned technologies for K1 MBT and K9 SPHs". Janes. Retrieved 20 March 2021.{{cite news}}: CS1 maint: url-status (link)
  39. ^ Kim, Dae Y. (6 January 2021). "Hyundai Rotem aims to roll out unmanned K1 MBT testbed by 2024". Janes. Retrieved 20 March 2021.{{cite news}}: CS1 maint: url-status (link)
  40. ^ a b c d e f g h [첨단국가의 초석, 방위산업] 한국형 전차 K1A1, retrieved 2022-09-19
  41. ^ 李瑄根특파원. "한국, 독일 무기에 관심". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  42. ^ "K-1전차 120mm 탄약 주생산업체 선정". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  43. ^ 李面照기자. "--국방위". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  44. ^ 成耆洪기자. ""잠수함 잡는 신형 輕어뢰 2001년 개발"(종합)". n.news.naver.com (in Korean). Retrieved 2022-09-21.
  45. ^ "國會 국정감사 계속(종합)". n.news.naver.com (in Korean). Retrieved 2022-09-19.
  46. ^ "한국형 120mm K-1 성능개량전차 첫 선". n.news.naver.com (in Korean). Retrieved 2022-09-20.
  47. ^ a b "전차포수조준경,熱영상장비 첫 개발". n.news.naver.com (in Korean). Retrieved 2022-09-20.
  48. ^ 李盛漢기자. "국방예산 실질삭감 1조3천억-戰力증강사업 손질 불가피". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  49. ^ "잠수함.유도미사일 사업 내년 추진". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  50. ^ 안승섭기자. "현대정공, 1조원 규모 K1A1전차 공급계약". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  51. ^ "국산 K1A1 전차, 실전 배치". n.news.naver.com (in Korean). Retrieved 2022-09-25.
  52. ^ a b "국방과학연구소 50주년". www.add.re.kr (in Korean). Retrieved 2022-09-26.
  53. ^ "한국형 K1전차 성능 개량 K1A1 전차개발 출고식". n.news.naver.com (in Korean). Retrieved 2022-09-24.
  54. ^ 유기자, 이. "155mm 자주포등 5건 최우수방산개발품 선정". n.news.naver.com (in Korean). Retrieved 2022-09-24.
  55. ^ "삼성탈레스 국방위 국감". n.news.naver.com (in Korean). Retrieved 2022-09-24.
  56. ^ "Special Armor Plate for K1A1 Tank, K2 Tank, Altay Tank". Samyang Comtech. Archived from the original on 2 September 2022. Retrieved 2 September 2022.
  57. ^ Seo Ho-geun (November 2020). "K계열 전차 장갑의 성능개량 필요성과 기술추세". The Korean Institute of Defense Technology. Archived from the original on 19 April 2021. Retrieved 19 April 2021.
  58. ^ "88전차를 기억하십니까.. K1". 네이버 블로그 | 앙마의 밀리터리 (in Korean). Retrieved 2022-09-24.
  59. ^ "지상전 최상위 포식자는 아직 나야.. K1A1". 네이버 블로그 | 앙마의 밀리터리 (in Korean). Retrieved 2022-09-24.
  60. ^ "K1 계열 전차의 포탑상면 볼트와 포방패 주변 너트에 대해 짤막하게". 네이버 블로그 | 성진호걸(腥塵好girl) (in Korean). Retrieved 2022-09-24.
  61. ^ 국방일보. "우리는 고구려 철갑기병 후예". 국방일보. Retrieved 2022-09-24.
  62. ^ 국방일보. "차관급 다수 편성, 대외 협력시 격 더 올라가". 국방일보. Retrieved 2022-09-24.
  63. ^ 국방일보. "두 개의 안테나·4색 위장 무늬... 디테일이 살아있다". 국방일보. Retrieved 2022-09-24.
  64. ^ a b "2022년까지 K1A1→ K1A2로 개량" (in Korean). The Korea Defense Daily. Archived from the original on 5 March 2017. Retrieved 21 May 2014.
  65. ^ a b "K1A2·K1E1, 성능개량으로 강해지는 전차!". Hyundai Rotem. 22 May 2020. Archived from the original on 16 June 2022. Retrieved 16 June 2022.
  66. ^ "(권홍우 선임기자의 무기 이야기)K1전차 개량 '환갑'까지...2024년부턴 에어컨도" (in Korean). Seoul Economy. 10 August 2018. Archived from the original on 14 August 2018. Retrieved 10 August 2018.
  67. ^ 김상범. ""국방부 국회승인 안거치고 26개사업 전력증강비 12조 늘려"". n.news.naver.com (in Korean). Retrieved 2022-12-08.
  68. ^ a b K1 ARV. Archived 2008-02-20 at the Wayback Machine Retrieved on 9 January 2008.
  69. ^ K1 AVLB. Archived 2008-02-20 at the Wayback Machine Retrieved on 9 January 2008.
  70. ^ Hyundai Rotem advances armoured armada Archived 2015-12-23 at the Wayback Machine – Shephardmedia.com, 22 October 2015.
Wikimedia Commons has media related to Type 88 K1.
Retrieved from "https://en.wikipedia.org/w/index.php?title=K1_tank&oldid=1134568483"