Jump to content

IATF 16949

From Wikipedia, the free encyclopedia

This is an old revision of this page, as edited by 213.172.134.164 (talk) at 13:10, 21 June 2024 (→Certification). The present address (URL) is a permanent link to this revision, which may differ significantly from the current revision.

IATF 16949:2016 is a technical specification aimed at the development of a quality management system which provides for continual improvement, emphasizing defect prevention and the reduction of variation and waste in the automotive industry supply chain and assembly process. It is based on the ISO 9001 standard and the first edition was published in June 1999 as ISO/TS 16949:1999.[1] IATF 16949:2016 replaced ISO/TS 16949 in October 2016.[2][3]

The standard was prepared by the International Automotive Task Force (IATF) and the "Technical Committee" of ISO. It harmonises the country-specific regulations of quality management systems.[4]

About 30 percent of the more than 100 existing motorcar manufacturers follow the requirements of the norm but especially the large Asian manufacturers have differentiated and have their own requirements for the quality management systems of their corporate group and their suppliers.[citation needed]

IATF 16949 applies to the design/development, production and, when relevant, installation and servicing of automotive-related products.

The requirements are intended to be applied throughout the supply chain. For the first time vehicle assembly plants will be encouraged to seek IATF 16949 [certification].

Historical background

Many suppliers (OEMs) were asked by the car manufacturers to build and certify their quality management system according to the rules and regulations of their own country organizations, such as:

  • VDA (Germany)
  • AIAG (North America)
  • AVSQ (Italy)
  • FIEV (France)
  • SMMT (UK)

But due to this regulation a supplier needed to provide two different certificates for Daimler and Chrysler (VDA 6.1 for Germany and QS 9000 America), even though the supplier delivered only to a single company. These complexities accelerated the need for harmonization.

Contents of the specification

The aim of the standard is to improve the system and process quality to increase customer satisfaction, to identify problems and risks in the production process and supply chain, to eliminate their causes and to examine and take corrective and preventive measures for their effectiveness.[5] The focus is not on the discovery, but on the avoidance of errors.

The ten main chapters of the standards are:

  • Chapter 1: Scope
  • Chapter 2: Normative References
  • Chapter 3: Terms and Definitions
  • Chapter 4: Context of the Organization
  • Chapter 5: Leadership
  • Chapter 6: Planning
  • Chapter 7: Support
    Includes Resources (personnel, infrastructure, equipment), Competence, Communication and Documented Information (record retention, engineering specifications)
  • Chapter 8: Operation
    Includes Requirements, Design & Development, Control of Production and Release of Products & Services
  • Chapter 9: Performance Evaluation
  • Chapter 10: Improvement

The process-oriented approach to business processes that is addressed in the ISO 9001:2015 is the base of the standard. It looks at the business processes in a process environment in which there are interactions and interfaces that need to be recognized, mapped and controlled by the quality management system. Additionally the gateways to the exterior (to sub-suppliers, customers and to remote locations) are defined. The Standard distinguishes between customer-oriented processes, supporting processes and management processes. This process-oriented approach is intended to improve the overview of the whole process. This is not an isolated process, but a combination of all interacting business processes which affect the quality performance of a firm.

A key requirement of IATF 16949:2016 is the fulfillment of customer-specific requirements, set up by the automotive manufacturer in addition to the quality management system of their suppliers. This may have decisively contributed to the worldwide recognition of the IATF standard by many manufacturers.

Certification

The IATF 16949 standard can be applied throughout the supply chain in the automotive industry. Certification takes place on the basis of the certification rules issued by the International Automotive Task Force (IATF). The certificate is valid for three years and must be confirmed annually (as a minimum) by an IATF certified auditor (3rd Party Auditor) of an IATF recognized certification body. Re-certification is required at the expiry of the three-year period. Certification pursuant to IATF 16949 is intended to build up or enforce the confidence of a (potential) customer towards the system and process quality of a (potential) supplier. Today, a supplier without a valid certificate has little chance of supplying a Tier 1 supplier and certainly no chance of supplying a car manufacturer with standard parts, if indeed that OEM is a participating member of the IATF (most Japan OEM are members of JAMA and not members of the IATF).[6]

Certification bodies include:

References

  1. ^ "ISO/TS 16949:1999".
  2. ^ IATF 16949:2016, accessed 21 February 2021
  3. ^ "IATF 16949:2016". Automotive Industry Action Group (AIAG). 2016-10-03. Retrieved 2016-11-11.
  4. ^ Cassel, Michael (2007). ISO/TS 16949 QM in der Automobilindustrie umsetzen. Germany: Carl Hanser Verlag. p. 1.
  5. ^ Kartha, C.P. (2004). "A comparison of ISO 9000:2000 quality system standards, QS9000, ISO/TS 16949 and Baldrige criteria". The TQM Magazine. 16 (5): 336. doi:10.1108/09544780410551269.
  6. ^ "Global Supplier". Daimler. 2002. p. 17.
  • ISO/TS 16949:2009 Quality management systems—Particular requirements for the application of ISO 9001:2008 for automotive production and relevant service part organizations
Retrieved from "https://en.wikipedia.org/w/index.php?title=IATF_16949&oldid=1230223045"