Bore (wind instruments)

Two instruments distinguished solely by bore

Difference may not be visible externally

In music, the bore of a wind instrument (including woodwind and brass) is its interior chamber. This defines a flow path through which air travels, which is set into vibration to produce sounds. The shape of the bore has a strong influence on the instrument's timbre.

Bore shapes

The cone and the cylinder are the two idealized shapes used to describe the bores of wind instruments. Other shapes are not generally used, as they tend to produce dissonant, anharmonic overtones and an unmusical sound. Instruments may consist of a primarily conical or cylindrical tube, but begin in a mouthpiece, and end in a rapidly-expanding "flare" or "bell". This flare reduces the acoustic impedance mismatch between the instrument and the air, allowing the instrument to transmit sound to the air more effectively.^[1]

These shapes affect the prominence of harmonics associated with the timbre of the instrument. A bore that flares from the mouthpiece reduces resistance to the breath, while a bore that narrows from the mouth increases it, compared to a cylinder.

Cylindrical bore

The diameter of a cylindrical bore remains constant along its length. The acoustic behavior depends on whether the instrument is stopped (closed at one end and open at the other), or open (at both ends). For an open pipe, the wavelength produced by the first normal mode (the fundamental note) is approximately twice the length of the pipe. The wavelength produced by the second normal mode is half that, that is, the length of the pipe, so its pitch is an octave higher; thus an open cylindrical bore instrument overblows at the octave. This corresponds to the second harmonic, and generally the harmonic spectrum of an open cylindrical bore instrument is strong in both even and odd harmonics. For a stopped pipe, the wavelength produced by the first normal mode is approximately four times the length of the pipe. The wavelength produced by the second normal mode is one third that, i.e. the 4/3 length of the pipe, so its pitch is a twelfth higher; a stopped cylindrical bore instrument overblows at the twelfth. This corresponds to the third harmonic; generally the harmonic spectrum of a stopped cylindrical bore instrument, particularly in its bottom register, is strong in the odd harmonics only. Modern brass instruments however generally make use of the full length of the instrument for every pitch, and are therefore significantly affected by the effects of the mouthpiece and bell. These modify the instrument's resonances to closely resemble that of a conical pipe, even if the bore is mostly cylindrical.^[2]

Instruments having a cylindrical, or mostly cylindrical, bore include:

Chalumeau
Clarinet
Cornamuse
Crumhorn
Flute (Boehm system — open)
Recorder (renaissance and some modern recorders)
Kortholt
Rackett (renaissance)
Trumpet
Trombone

Conical bore

The diameter of a conical bore varies linearly with distance from the end of the instrument. A complete conical bore would begin at zero diameter—the cone's vertex. However, actual instrument bores approximate a frustum of a cone. The wavelength produced by the first normal mode is approximately twice the length of the cone measured from the vertex. The wavelength produced by the second normal mode is approximately equal to the length of the cone, so its pitch is an octave higher. Therefore, a conical bore instrument, like one with an open cylindrical bore, overblows at the octave and generally has a harmonic spectrum strong in both even and odd harmonics.

Instruments having a conical, or approximately conical, bore include:

Alphorn
Bassoon
Conch shell
Cornet
Dulcian
Euphonium
Flugelhorn
Flute (pre-Boehm)
French Horn
Recorder (baroque and most contemporary recorders)
Oboe
Rackett (baroque)
Rauschpfeife
Saxhorn
Saxophone
Shawm
Trembita
Tuba
Uilleann pipes

Woodwinds

Sections of the bores of woodwind instruments deviate from a true cone or a cylinder. For example, although oboes and oboes d'amore are similarly pitched, they have differently shaped terminal bells. Accordingly, the voice of the oboe is described as "piercing" as compared to the more "full" voice of the oboe d'amore.

Although the bore shape of woodwind instruments generally determines their timbre, the instruments' exterior geometry typically has little effect on their voice. In addition, the exterior shape of woodwind instruments may not overtly match the shape of their bores. For example, while oboes and clarinets may outwardly appear similar, oboes have a conical bore while clarinets have a cylindrical bore.

The bore of a baroque recorder has a "reversed" taper, being wider at the head and narrower at the foot of the instrument.^[3] Most contemporary recorders also have such a conical bore as they are made very similar to baroque recorders. However, multiple renaissance, medieval and also modern recorders have a cylindrical bore. Some tin flageolets also have a reverse taper.

Brasses

Brass instruments also are sometimes categorized as conical or cylindrical, though most in fact have cylindrical sections between a conical section (the mouthpiece taper or leadpipe) and a non-conical, non-cylindrical flaring section (the bell). Benade gives the following typical proportions:^[4]

	Trumpet	Trombone	Horn
Mouthpiece taper	21%	9%	11%
Cylindrical part	29%	52%	61%
Bell	50%	39%	28%

These proportions vary as valves or slides are operated; the above numbers are for instruments with the valves open or the slide fully in. This deviation from standard models of cylindrical and conical tubes means normal mode frequencies of brass instruments do not correspond to integer multiples of the first mode, which is not used for playing. The higher modes however do correspond fairly to integer multiples of a "fictitious fundamental" which can often still be played as a pedal tone.^[5] Players of brasses (in contrast to woodwinds) are able to "lip" notes up or down substantially, and on some instruments make use of privileged frequencies (pedal tones and false tones), to obtain in-tune notes outside of the range allowed for by the normal modes.^[4]

Sources

^ "sound - Steady-state waves | Britannica". www.britannica.com.
^ "Producing a harmonic sequence of notes with a trumpet". hyperphysics.phy-astr.gsu.edu.
^ Barr, Chris. "Differences Between Conical And Cylindrical Bore Instruments?". Sonic Function.
^ ^a ^b Benade, Arthur H. (1992). Horns, Strings, and Harmony. New York: Dover. p. 192.
^ "The Pedal Tone". hyperphysics.phy-astr.gsu.edu.

v t e Brass instruments
Modern	Trumpet Contrabass Bass Piccolo Pocket trumpet Fanfare trumpet Firebird Flumpet Cornet Soprano cornet Horn Bugle French horn German horn Vienna horn Wagner tuba Trombone Contrabass Bass Alto Soprano Superbone Cimbasso Saxhorn Baritone horn Alto/Tenor horn Flugelhorn Fiscorn Kuhlohorn Tuba Subcontrabass tuba Euphonium Double bell euphonium
Antiquated	Clarion Cornett Cornettino Mute cornett Tenor cornett Cornu Dord Natural horn Post horn Natural trumpet Baroque trumpet Buccina Slide trumpet Buccin Sackbut Helicon Soprano helicon Ophicleide Serpent Sudrophone Saxtuba Saxotromba Bazooka Jazzophone
Indigenous	Alphorn Nabal Vuvuzela Nyele Carnyx Shofar Sringa Tibetan horn Wazza
Marching	Mellophone Marching baritone horn Marching euphonium Trombonium Sousaphone Contrabass bugle
Parts/technique	Valves Piston valve Rotary valve Mutes Hand-stopping Embouchure Mouthpiece Falset Pedal tone Bore Valve oil Crook Leadpipe Water key Axial flow valve Harmonic series
Ensembles	Brass band British brass band Balkan brass Brass quintet Drum and bugle corps (classic) Drum and bugle corps (modern)
Players	(all) Trumpeters Jazz trumpeters Horn players Classical trombonists Jazz trombonists Euphonium players Tubists
Other	Pitch of brass instruments Brass section Horn section List of euphonium, baritone horn and tenor horn manufacturers