South African Class 19E

South African Class 19E
No. 19-009, 19-054 and 19-067 at the Richards Bay Locomotive Depot, 8 December 2013
Type and origin Power type Electric Designer Mitsui Builder Union Carriage & Wagon Model Mitsui 19E Build date 2007-2011 Total produced 110
Specifications Configuration: ​  • AAR B-B  • UIC Bo'Bo' Gauge 3 ft 6 in (1,067 mm) Cape gauge Wheel diameter 1,250 mm (49.2 in) Length: ​  • Over couplers 18,300 mm (60 ft 0.5 in) Axle load 26,000 kg (57,000 lb) Adhesive weight 104,000 kg (229,000 lb) Loco weight 104,000 kg (229,000 lb) max Power supply Catenary Current pickup(s) Pantographs Loco brake Air, Regenerative &Rheostatic Train brakes Air Couplers AAR knuckle
Performance figures Maximum speed 120 km/h (75 mph) operating 132 km/h (82 mph) by design Power output: ​  • Continuous 3,000 kW (4,000 hp) Tractive effort: ​  • Starting 392 kN (88,000 lbf)  • Continuous 300 kN (67,000 lbf)
Career Operators Transnet Freight Rail Class 19E Power class 3 kV DC & 25 kV AC/50Hz Number in class 110 Numbers 19-001 to 19-110 Delivered 2009 First run 2009

The Transnet Freight Rail Class 19E of 2009 is a South African electric locomotive.

In 2009, Transnet Freight Rail placed the first of 110 Class 19E single-cab dual-voltage 3 kV DC and 25 kV AC electric locomotives with a Bo-Bo wheel arrangement in service on the Coalink line from Ermelo to Richards Bay.

Manufacturer

The dual-voltage 3 kV DC and 25 kV AC Class 19E is the product of a joint venture by Mitsui for the design, Toshiba for the electrical equipment, Union Carriage and Wagon (UCW) for the bodies and the RSD division of DCD-Dorbyl for the bogies. It was locally manufactured by UCW in Nigel, Gauteng. Road testing on the Class 19E started in August 2008.

Characteristics

The Class 19E was the first South African AC locomotive to incorporate regenerative as well as rheostatic electric braking. While, with the notable exception of the Class 18E, regenerative braking was used on all South African 3 kV DC mainline locomotives dating back all the way to the introduction of the Class 1E in 1925, all earlier 25 kV and 50 kV AC South African locomotives made use of rheostatic braking only.

The locomotive features Toshiba-made 3-phase AC motors, powered through Insulated-gate bipolar transistor (IGBT) control. It is a dual voltage locomotive, designed to operate on either 3 kV DC or 25 kV AC and, to facilitate automatic trouble-free transition on the run, it is equipped with onboard voltage detectors. Like the earlier Classes 7E1, 7E4, 9E, 11E, 15E and 18E electric locomotives, these engines have driving cabs at one end only, since they would only be utilised in multi-unit consists.

As on the dual voltage Classes 20E and 21E, the main electric circuit is automatically selected in either AC or DC mode, based on the voltage of the overhead contact wire feeding the locomotive. To facilitate automatic trouble-free transition on the run, the locomotive is equipped with onboard voltage detectors, while the overhead wire is equipped with two wooden isolators and a 3 metres (10 feet) length of neutral wire to separate the AC and DC feeds. The neutral section is connected to the rails, which serve as the return conductor on electrified lines.

The transition process requires that the locomotive should be switched off automatically before it reaches the isolators and the unpowered overhead wire section, and automatically restarted after exiting from under the unpowered wire. This is done by a pair of track magnets, one on either side of the neutral overhead wire and spaced 45 metres (148 feet) apart. The two magnets are mounted with their polarities reversed in relation to each other and they activate a magnetic relay, located underneath the locomotive, to do the switching off and restarting.

By July 2009, Transnet Freight Rail (TFR) had taken delivery of the first three Class 19E locomotives, and UCW intended to deliver between six and eight new units per quarter.

Service

The Class 19E locomotives were placed in service on the 580 kilometres (360 miles) long Coalink line from Ermelo to Richards Bay, to haul export coal from forty-four coal mines in Mpumalanga to the Richards Bay Coal Terminal (RBCT), the export coal harbour in Richards Bay, KwaZulu-Natal. In the process, it relieved some Classes 7E, 7E1 and 7E3 electric locomotives on the Coalink Line for use elsewhere.

Illustration

• 
  No. 19-011 at Ermelo, Mpumalanga, 18 September 2010