This article needs additional citations for verification. (February 2012) (Learn how and when to remove this template message)
This article's factual accuracy is disputed. (March 2017) (Learn how and when to remove this template message)
A firearm malfunction is the failure of a firearm to operate as intended for causes other than user error. Malfunctions range from temporary and relatively safe situations, such as a casing that didn't eject, to potentially dangerous occurrences that may permanently damage the gun and cause injury or death. Improper handling of certain types of malfunctions can be very dangerous. The basic rules of firearms safety should be followed at all times to minimize the risk to shooters and bystanders.  Proper cleaning and maintenance of a firearm plays a big role in preventing malfunctions. 
- 1 Cartridge malfunctions
- 2 Mechanical malfunctions
- 3 Prevention
- 4 See also
- 5 References
Case head separation
Case head separation occurs when the walls of the casing become thin or fatigued. Upon firing the round, the case separates into two pieces near the head. It is not uncommon with brass that has been reloaded several times.
A dud (also a misfire or failure to fire) occurs when the trigger is pulled but the primer or powder in the cartridge malfunctions, causing the firearm not to discharge. Dud rounds can still be dangerous and should be deactivated and disposed of properly.
A hang fire (also delayed discharge) is an unexpected delay between the triggering of a firearm and the ignition of the propellant. Whenever a firearm fails to fire, but has not clearly malfunctioned, a hang fire should be suspected. When this occurs, the correct procedure is to keep the firearm pointed downrange or in a safe direction for thirty to sixty seconds, then remove and safely discard the round (which is now a dud as explained above if the primer was struck, otherwise the gun itself may have malfunctioned). The reason for this is that a round functioning outside of the firearm, or in the firearm with the action open (out-of-battery discharge), could cause a serious fragmentation hazard.
A squib load (also squib round, squib, squib fire, insufficient discharge, incomplete discharge) is an extremely dangerous malfunction that happens when a fired projectile does not carry enough force and becomes stuck in the gun barrel instead of exiting it. In the case of semi-automatic or automatic weapons, this can cause subsequent rounds to impact the projectile obstructing the barrel, which can cause a catastrophic failure of the structural integrity of the firearm, posing a threat to the operator or bystanders. The bullet from a squib stuck in the barrel must never be cleared by subsequently attempting to fire a live or blank round into an obstructed barrel. Blank rounds use a type of powder different from that of other rounds, and generate much more pressure, which, combined with the presence of the projectile obstructing the barrel may cause the firearm to fail catastrophically.
Mechanical malfunctions of a firearm (commonly called jams) include failures to feed, extract, or eject a cartridge; failure to fully cycle after firing; and failure of a recoil- or gas-operated firearm to lock back when empty (largely a procedural hazard, as "slide lock" is a visual cue that the firearm is empty). In extreme cases, an overloaded round, blocked barrel, poor design and/or severely weakened breech can result in an explosive failure of the receiver, barrel, or other parts of the firearm.
Failure to feed
This section's factual accuracy is disputed. (March 2017) (Learn how and when to remove this template message)
Failure to Feed (FTF) is when a firearm fails to feed the next round into the firing chamber. Failure to feed is common when the shooter does not hold the firearm firmly (known as limp wristing), when the slide is not fully cycled by the preceding round, or due to problems with the magazine.
Hammer follow occurs when the disconnector allows the hammer to follow the bolt and firing pin into battery, sometimes causing the firing mechanism to function without pulling the trigger. This is usually a result of extreme wear or outright breakage of firing mechanism components, and can result in uncontrollable "full-auto" operation, in which multiple rounds are discharged following a single pull of the trigger.
A slamfire is a premature, unintended discharge of a firearm that occurs as a round is being loaded into the chamber, when the bolt "slams" forward (hence the name), as a result of the firing pin having not been retracted into the bolt, or from the firing pin being carried forward by the momentum of returning to battery. Similarly to a hammer follow malfunction, this can result in uncontrollable "full-auto" operation.
Failure to extract
A failure to extract occurs when the casing of the just-fired round is not successfully extracted from the chamber. This can be caused by an overly-dirty chamber, broken extractor claw, case rim failures, or several other causes.
Failure to eject
A failure to eject (FTE) occurs when the casing of the just-fired round is extracted from the chamber, but is not ejected from the firearm, causing the next round to fail to feed, or the slide/bolt to fail to return to battery. A stovepipe is common type of FTE.
A stovepipe or smokestack typically occurs in pump action, semi-automatic, and fully automatic firearms that fire from a closed bolt, when an empty cartridge case gets caught partway out of the ejection port instead of being thrown clear. Stovepipes can be caused by a malfunctioning or defective extractor or ejector, or when the shooter does not hold the firearm firmly enough for the action to function fully, known as limp wristing, or due to reloads that are not sufficiently powerful to fully cycle the action, etc.
Double feed (Type 3 Malfunction)
A double feed occurs when an expended round is in the chamber AND the slide picks up a second round from the magazine mashing it into the first. This can be caused by a broken extractor or a broken casing left behind in the chamber, and to be cleared could require simple tools.
A firearm is "in-battery" when the slide/bolt is in the normal firing position. A firearm is "out-of-battery" when the slide/bolt/action is not fully seated in the normal firing position, typically because it did not cycle fully after firing (called "returning to battery"). Most modern firearms are designed to not be capable of firing when significantly out-of-battery. As such, a firearm that is out-of-battery typically cannot be fired, which is why this is a type of firearm malfunction.
A dangerous situation can occur when a chambered round fires when the firearm is out-of-battery (called an out-of-battery discharge). The cartridge casing is not sufficiently strong to contain the pressure of firing by itself; it relies on the walls of the chamber and the bolt face to help contain the pressure. When the firearm is out-of-battery, the round is not fully chambered, or the bolt face is not against the rear of the cartridge, and if the round is fired in this situation, the case will fail, causing high-pressure hot gasses, bits of burning powder, and fragments of the casing itself to be thrown at high-speed from the firearm. This can be a serious hazard to the operator of the firearm, and any bystanders.
Some mechanical malfunctions are caused by poor design and cannot easily be avoided. Some malfunctions with cartridges can be attributed to poor quality or damaged ammunition (often due to improper storage, exposure to moisture). Many malfunctions, however, can be prevented by proper cleaning and maintenance of the firearm.
This article is missing information about solutions and procedures.(March 2017)