A screenshot of CP/M-86
|Developer||Digital Research, Inc./ Gary Kildall|
|Source model||Originally closed source, now open source|
|Latest release||3.1 / 1983|
|Platforms||Intel 8080, Intel 8085, Zilog Z80, Zilog Z8000, Intel 8086, Motorola 68000|
|Kernel type||Monolithic kernel|
|Default user interface||Command-line interface|
|License||Originally proprietary, now BSD-like|
|Official website||Digital Research official CP/M page|
CP/M, originally standing for Control Program/Monitor and later Control Program for Microcomputers, is a mass-market operating system created for Intel 8080/85-based microcomputers by Gary Kildall of Digital Research, Inc. Initially confined to single-tasking on 8-bit processors and no more than 64 kilobytes of memory, later versions of CP/M added multi-user variations and were migrated to 16-bit processors.
The combination of CP/M and S-100 bus computers was loosely patterned on the MITS Altair, an early standard in the microcomputer industry. This computer platform was widely used in business through the late 1970s and into the mid-1980s. CP/M increased the market size for both hardware and software by greatly reducing the amount of programming required to install an application on a new manufacturer's computer. An important driver of software innovation was the advent of (comparatively) low-cost microcomputers running CP/M, as independent programmers and hackers bought them and shared their creations in user groups. CP/M was displaced by MS-DOS soon after the 1981 introduction of the IBM PC.
- 1 Hardware model
- 2 Components of the operating system
- 3 History
- 4 Legacy
- 5 See also
- 6 References
- 7 Further reading
- 8 External links
A minimal 8-bit CP/M system would contain the following components:
- A computer terminal using the ASCII character set
- An Intel 8080 (and later the 8085) or Zilog Z80 microprocessor
- At least 16 kilobytes of RAM, beginning at address 0
- A means to bootstrap the first sector of the diskette
- At least one floppy disk drive
The only hardware system that CP/M, as sold by Digital Research, would support was the Intel 8080 Development System. Manufacturers of CP/M-compatible systems customized portions of the operating system for their own combination of installed memory, disk drives, and console devices. CP/M would also run on systems based on the Zilog Z80 processor since the Z80 was compatible with 8080 code. While the Digital Research distributed core of CP/M (BDOS, CCP, core transient commands) did not use any of the Z80-specific instructions, many Z80-based systems used Z80 code in the system-specific BIOS, and many applications were dedicated to Z80-based CP/M machines.
On most machines the bootstrap was a minimal bootloader in ROM combined with some means of minimal bank switching or a means of injecting code on the bus (since the 8080 needs to see boot code at Address 0 for start-up, while CP/M needs RAM there); for others, this bootstrap had to be entered into memory using front-panel controls each time the system was started.
CP/M used the 7-bit ASCII set. The other 128 characters made possible by the 8-bit byte were not standardized. For example, one Kaypro used them for Greek characters, and Osborne machines used the 8th bit set to indicate an underlined character. WordStar used the 8th bit as an end-of-word marker. International CP/M systems most commonly used the ISO 646 norm for localized character sets, replacing certain ASCII characters with localized characters rather than adding them beyond the 7-bit boundary.
Components of the operating system
In the 8-bit versions, while running, the CP/M operating system loaded into memory had three components:
- Basic Input/Output System or BIOS,
- Basic Disk Operating System or BDOS,
- Console Command Processor or CCP.
The BIOS and BDOS were memory-resident, while the CCP was memory-resident unless overwritten by an application, in which case it was automatically reloaded after the application finished running. A number of transient commands for standard utilities were also provided. The transient commands resided in files with the extension .COM on disk.
The BIOS directly controlled hardware components other than the CPU and main memory. It contained functions such as character input and output and the reading and writing of disk sectors. The BDOS implemented the CP/M file system and some input/output abstractions (such as redirection) on top of the BIOS. The CCP took user commands and either executed them directly (internal commands such as DIR to show a directory or ERA to delete a file) or loaded and started an executable file of the given name (transient commands such as PIP.COM to copy files or STAT.COM to show various file and system information). Third-party applications for CP/M were also essentially transient commands.
The BDOS, CCP and standard transient commands were (ideally) the same in all installations of a particular revision of CP/M, but the BIOS portion was always adapted to the particular hardware. Adding memory to a computer, for example, meant that the CP/M system had to be reinstalled with an updated BIOS capable of addressing the additional memory. A utility was provided to patch the supplied BIOS, BDOS and CCP to allow them to be run from higher memory. Once installed, the operating system (BIOS, BDOS and CCP) was stored in reserved areas at the beginning of any disk which would be used to boot the system. On start-up, the bootloader (usually contained in a ROM firmware chip) would load the operating system from the disk in drive
By modern standards CP/M was primitive, owing to the extreme constraints on program size. With version 1.0 there was no provision for detecting a changed disk. If a user changed disks without manually rereading the disk directory the system would write on the new disk using the old disk's directory information, ruining the data stored on the disk. From version 1.1 or 1.2 onwards, changing a disk then trying to write to it before its directory was read would cause a fatal error to be signalled. This avoided overwriting the disk but required a reboot and loss of the data that was to be stored on disk.
The majority of the complexity in CP/M was isolated in the BDOS, and to a lesser extent, the CCP and transient commands. This meant that by porting the limited number of simple routines in the BIOS to a particular hardware platform, the entire OS would work. This significantly reduced the development time needed to support new machines, and was one of the main reasons for CP/M's widespread use. Today this sort of abstraction is common to most OSs (a hardware abstraction layer), but at the time of CP/M's birth, OSs were typically intended to run on only one machine platform, and multilayer designs were considered unnecessary.
Console Command Processor
The Console Command Processor, or CCP, accepted input from the keyboard and conveyed results to the terminal. CP/M itself would work with either a printing terminal or a video terminal. All CP/M commands had to be typed in on the command line. The console would most often display the
A> prompt, to indicate the current default disk drive. When used with a video terminal, this would usually be followed by a blinking cursor supplied by the terminal. The CCP would await input from the user.
A CCP internal command, of the form drive letter followed by a colon, could be used to select the default drive. For example, typing
B: and pressing enter at the command prompt would change the default drive to B, and the command prompt would then become
B> to indicate this change.
Commands took the form of a keyword followed by a list of parameters separated by spaces or special characters. Similar to a Unix shell builtin, if an internal command was recognized, it was carried out by the CCP itself. Otherwise it would attempt to find an executable file on the currently logged disk drive and (in later versions) user area, load it, and pass it any additional parameters from the command line. These were referred to as "transient" programs. On completion, CP/M would reload the part of the CCP that had been overwritten by application programs — this allowed transient programs a larger memory space.
The commands themselves could sometimes be obscure. For instance, the command to duplicate files was named
PIP (Peripheral-Interchange-Program), the name of the old DEC utility used for that purpose. The format of parameters given to a program was not standardized, so that there was no single option character that differentiated options from file names. Different programs could and did use different characters.
Basic Disk Operating System
The Basic Disk Operating System, or BDOS, provided access to such operations as opening a file, output to the console, or printing. Application programs would load processor registers with a function code for the operation, and addresses for parameters or memory buffers, and call a fixed address in memory. Since the address was the same independent of the amount of memory in the system, application programs would run the same way for any type or configuration of hardware.
Basic Input Output System
These included reading or writing single characters to the system console and reading or writing a sector of data from the disk. The BDOS handled some of the buffering of data from the diskette, but before CP/M 3.0 it assumed a disk sector size fixed at 128 bytes, as used on single-density 8-inch floppy disks. Since most 5.25-inch disk formats used larger sectors, the blocking and deblocking and the management of a disk buffer area was handled by model-specific code in the BIOS.
Customization was required because hardware choices were not constrained by compatibility with any one popular standard. For example, some manufacturers used separate computer terminal, while others designed a built-in integrated video display system. Serial ports for printers and modems could use different types of UART chips, and port addresses were not fixed. Some machines used memory-mapped I/O instead of the 8080 I/O address space. All of these variations in the hardware were concealed from other modules of the system by use of the BIOS, which used standard entry points for the services required to run CP/M such as character I/O or accessing a disk block. Since support for serial communication to a modem was very rudimentary in the BIOS or may have been absent altogether, it was common practice for CP/M programs that used modems to have a user-installed overlay containing all the code required to access a particular machine's serial port.
File names were specified as a string of up to eight characters, followed by a period, followed by a file name extension of up to three characters ("8.3" filename format). The extension usually identified the type of the file. For example,
.COM indicated an executable program file, and
.TXT indicated a file containing ASCII text.
Each disk drive was identified by a drive letter, for example drive
A and drive
B. To refer to a file on a specific drive, the drive letter was prefixed to the file name, separated by a colon, e.g.
A:FILE.TXT. With no drive letter prefixed, access was to files on the current default drive.
The "8.3" filename format and the drive letter + colon combination survived into MS-DOS. The drive letter + colon convention has survived in Microsoft Windows and is still used today. In addition, file extensions (for example,
.com (a compiled file), or
.exe (an executable file)) are still used to identify file types on many operating systems.
File size was specified as the number of 128-byte records (directly corresponding to disk sectors on 8-inch drives) occupied by a file on the disk. There was no generally supported way of specifying byte-exact file sizes. The current size of a file was maintained in the file's File Control Block (FCB) by the operating system. Since many application programs (such as text editors) prefer to deal with files as sequences of characters rather than as sequences of records, by convention text files were terminated with a control-Z character (ASCII SUB, hexadecimal 1A). Determining the end of a text file therefore involved examining the last record of the file to locate the terminating control-Z. This also meant that inserting a control-Z character into the middle of a file usually had the effect of truncating the text contents of the file.
With the advent of larger removable and fixed disk drives, disk de-blocking formulas were employed which resulted in more disk blocks per logical file allocation block. While this allowed for larger file sizes, it also meant that the smallest file which could be allocated increased in size from 1KB (on single-density drives) to 2KB (on double-density drives) and so on, up to 32KB for a file containing only a single byte. This made for inefficient use of disk space if the disk contained a large number of small files.
File modification time stamps were not supported in releases up to CP/M 2.2, but were an optional feature in MP/M and CP/M 3.0.
CP/M 2.2 had no sub-directories in the file structure, but provided 16 numbered user areas to organize files on a disk. To change user one had to simply type "User X" at the command prompt, X being the number of the user wanted; security was non-existent and not believed to be necessary. The user area concept was to make the single-user version of CP/M somewhat compatible with multi-user MP/M systems. A common patch for the CP/M and derivative operating systems was to make one user area accessible to the user independent of the currently set user area. A USER command allowed the user area to be changed to any area from 0 to 15. User 0 was the default. If one changed to another user, such as USER 1, the material saved on the disk for this user would only be available to USER 1; USER 2 would not be able to see it or access it. However, files stored in the USER 0 area were accessible to all other users; their location was specified with a prefatory path, since the files of USER 0 were only visible to someone logged in as USER 0. The user area feature arguably had little utility on small floppy disks, but it was useful for organizing files on machines with hard drives. The intent of the feature was to ease use of the same computer for different tasks. For example, a secretary could do data entry, then, after switching USER areas, another employee could use the machine to do billing without their files intermixing.
Transient Program Area
The read/write memory between address 0100 hexadecimal and the lowest address of the BDOS was the Transient Program Area (TPA) available for CP/M application programs. Although all Z80 and 8080 processors could address 64 kilobytes of memory, the amount available for application programs could vary, depending on the design of the particular computer. Some computers used large parts of the address space for such things as BIOS ROMs, or video display memory. As a result, some systems had more TPA memory available than others. Bank switching was a common technique that allowed systems to have a large TPA while switching out ROM or video memory space as needed. CP/M 3.0 allowed parts of the BDOS to be in bank-switched memory as well.
CP/M came with a Dynamic Debugging Tool, nicknamed DDT (after the insecticide, i.e. a bug-killer), which allowed memory and program modules to be examined and manipulated, and allowed a program to be executed one step at a time.
CP/M originally did not support the equivalent of terminate and stay resident program as under DOS. Programmers could write software that could intercept certain operating system calls and extend or alter their functionality. Using this capability, programmers developed and sold auxiliary desk accessory programs, such as SmartKey, a keyboard utility to assign any string of bytes to any key. CP/M 3, however, added support for dynamically loadable Resident System Extensions (RSX), and similar solutions (like RSM) were also retrofitted to CP/M 2.2 systems by third-parties.
Although CP/M provided some hardware abstraction to standardize the interface to disk I/O or console I/O, typically application programs still required installation to make use of all the features of such equipment as printers and terminals. Often these were controlled by escape sequences which had to be altered for different devices. For example, the escape sequence to select bold face on a printer would have differed among manufacturers, and sometimes among models within a manufacturer's range. This procedure was not defined by the operating system; a user would typically run an installation program that would either allow selection from a range of devices, or else allow feature-by-feature editing of the escape sequences required to access a function. This had to be repeated for each application program, since there was no central operating system service provided for these devices.
The initializing codes for each model of printer had to be written into the application. To use a program such as Wordstar with more than one printer (say, a fast dot matrix printer or a slower but presentation-quality daisy wheel printer), a separate version of Wordstar had to be prepared, and one had to load the Wordstar version that corresponded to the printer selected (and exiting and reloading to change printers).
This section needs additional citations for verification. (January 2009) (Learn how and when to remove this template message)
The beginning and CP/M's heyday
Gary Kildall originally developed CP/M during 1974, as an operating system to run on an Intel Intellec-8 development system, equipped with a Shugart Associates 8-inch floppy disk drive interfaced via a custom floppy disk controller. It was written in Kildall's own PL/M (Programming Language for Microcomputers). Various aspects of CP/M were influenced by the TOPS-10 operating system of the DECsystem-10 mainframe computer, which Kildall had used as a development environment.
CP/M originally stood for "Control Program/Monitor", a name which implies a resident monitor—a primitive precursor to the operating system. However, during the conversion of CP/M to a commercial product, trademark registration documents filed in November 1977 gave the product's name as "Control Program for Microcomputers". The CP/M name follows a prevailing naming scheme of the time, as in Kildall's PL/M language, and Prime Computer's PL/P (Programming Language for Prime), both suggesting IBM's PL/I; and IBM's CP/CMS operating system, which Kildall had used when working at the Naval Postgraduate School.
This renaming of CP/M was part of a larger effort by Kildall and his wife/business partner to convert Kildall's personal project of CP/M and the Intel-contracted PL/M compiler into a commercial enterprise. The Kildalls intended to establish the Digital Research brand and its product lines as synonymous with "microcomputer" in the consumer's mind, similar to what IBM and Microsoft together later successfully accomplished in making "personal computer" synonymous with their product offerings. Intergalactic Digital Research, Inc. was later renamed via a corporation change-of-name filing to Digital Research, Inc.
Companies chose to support CP/M because of its large library of software. The Xerox 820 ran the operating system because "where there are literally thousands of programs written for it, it would be unwise not to take advantage of it", Xerox said. By 1984 Columbia University used the same source code to build Kermit binaries for more than a dozen different CP/M systems, plus a generic version. The operating system was described as a "software bus", allowing multiple programs to interact with different hardware in a standardized way. Programs written for CP/M were typically portable among different machines, usually requiring only the specification of the escape sequences for control of the screen and printer. This portability made CP/M popular, and much more software was written for CP/M than for operating systems that ran on only one brand of hardware. One restriction on portability was that certain programs used the extended instruction set of the Z80 processor and would not operate on an 8080 or 8085 processor. Another was graphics routines, especially in games and graphics programs, which were generally machine specific as they used direct hardware access for speed, bypassing the OS and BIOS (this was also a common problem in early DOS machines).
Bill Gates claimed that the Apple II family with a Z-80 SoftCard was the single most-popular CP/M hardware platform. Many different brands of machines ran the operating system, some notable examples being the Altair 8800, the IMSAI 8080, the Osborne 1 and Kaypro luggables, and MSX computers. The best-selling CP/M-capable system of all time was probably the Amstrad PCW. In the UK, CP/M was also available on Research Machines educational computers (with the CP/M source code published as an educational resource), and for the BBC Micro when equipped with a Z80 co-processor. Furthermore, it was available for the Amstrad CPC series, the Commodore 128, TRS-80, and later models of the ZX Spectrum. CP/M 3 was also used on the NIAT, a custom handheld computer designed for A.C. Nielsen's internal use with 1 Mbytes of SSD memory.
WordStar, one of the first widely used word processors, and dBase, an early and popular database program for small computers, were originally written for CP/M. Two early outliners, KAMAS (Knowledge and Mind Amplification System) and its cut-down successor Out-Think (without programming facilities and retooled for 8080/V20 compatibility) were also written for CP/M, though later rewritten for MS-DOS. Turbo Pascal, the ancestor of Borland Delphi, and Multiplan, the ancestor of Microsoft Excel, also debuted on CP/M before MS-DOS versions became available. Visicalc, the first-ever spreadsheet program, was made available for CP/M. Another company, Sorcim, created its SuperCalc spreadsheet for CP/M, which would go on to become the market leader and de facto standard on CP/M. Supercalc would go on to be a competitor in the spreadsheet market in the MS-DOS world. AutoCAD, a CAD application from Autodesk debuted on CP/M. A host of compilers and interpreters for popular programming languages of the time (such as BASIC, Borland's Turbo Pascal and FORTRAN) were available, among them several of the earliest Microsoft products.
CP/M software often came with installers that adapted it to a wide variety of computers. Most forms of copy protection were ineffective on the operating system, and the source code for BASIC programs was easily accessible. The lack of standardized graphics support limited video games, but various character and text-based games were ported, such as Telengard, Gorillas (video game), Hamurabi, Lunar Lander, along with early interactive fiction including the Zork series and Colossal Cave Adventure. A text adventure specialist, Infocom was one of the few publishers to consistently release their games in CP/M format. Lifeboat Associates started collecting and distributing user-written "free" software. One of the first was XMODEM, which allowed reliable file transfers via modem and phone line. The last significant program native to CP/M was the outline processor KAMAS.
No standard 5 1/4-inch CP/M disk format existed. While the 8-inch single-density floppy disk format (so-called "distribution format") was standardized, various 5 1/4-inch formats were used depending on the characteristics of particular systems and to some degree the choices of the designers. CP/M supported options to control the size of reserved and directory areas on the disk, and the mapping between logical disk sectors (as seen by CP/M programs) and physical sectors as allocated on the disk. There were many ways to customize these parameters for every system but once they had been set, no standardized way existed for a system to load parameters from a disk formatted on another system.
JRT Pascal, for example, provided versions on 5 1⁄4-inch disk for North Star, Osborne, Apple, Heath hard sector and soft sector, and Superbrain, and a single 8-inch version. Certain disk formats were more popular than others. The Xerox 820's became widely supported, for example; much software was available on it, and other computers such as the Kaypro II were compatible with the format. No single manufacturer, however, prevailed in the 5 1⁄4-inch era of CP/M use, and disk formats were not portable between hardware manufacturers. A software manufacturer had to prepare a separate version of the program for each brand of hardware on which it was to run. With some manufacturers (Kaypro is an example), there was not even standardization across the company's different models. Because of this situation, disk format translation programs, which allowed a machine to read many different formats, became popular and reduced the confusion, as did programs like Kermit which allowed transfer of data and programs from one machine to another using the serial ports that most CP/M machines had.
The fragmented CP/M market, requiring distributors either to stock multiple formats of disks or to invest in multiformat duplication equipment, compared with the more standardized IBM PC disk formats, was a contributing factor to the rapid obsolescence of CP/M after 1981.
Although graphics-capable S-100 systems existed from the commercialization of the S-100 bus, CP/M did not provide any standardized graphics support until 1982 with GSX (Graphics System Extension). Owing to the small memory available, graphics was never a common feature associated with 8-bit CP/M operating systems. Most systems could only display rudimentary ASCII art charts and diagrams in text mode or by using a custom character set.
In 1979, a multi-user compatible derivative of CP/M was released. MP/M allowed multiple users to connect to a single computer, using multiple terminals to provide each user with a screen and keyboard. Later versions ran on 16-bit processors.
The last 8-bit version of CP/M was version 3, often called CP/M Plus, released in 1983. It incorporated the bank switching memory management of MP/M in a single-user single-task operating system compatible with CP/M 2.2 applications. CP/M 3 could therefore use more than 64 kB of memory on an 8080 or Z80 processor. The system could be configured to support date stamping of files. The operating system distribution software also included a relocating assembler and linker. CP/M 3 was available for the last generation of 8-bit computers, notably the Amstrad PCW, the ZX Spectrum +3, the Commodore 128, and the Radio Shack TRS-80 Model 4.
The 16-bit world
There were versions of CP/M for some 16-bit CPUs as well.
The first version in the 16-bit family was CP/M-86 for the Intel 8086, which was soon followed by CP/M-68K for the Motorola 68000. The original version of CP/M-68K in 1982 was written in Pascal/MT+68k, but it was ported to C later on. At this point the original 8-bit CP/M became known by the retronym CP/M-80 to avoid confusion. In ca. 1982/1983 there was also a port to the Zilog Z8000 for the Olivetti M20, written in C, named CP/M-8000.
CP/M-86 was expected to be the standard operating system of the new IBM PCs, but DRI and IBM were unable to negotiate development and licensing terms. IBM turned to Microsoft instead, and Microsoft delivered PC DOS based on a CP/M clone, 86-DOS. Although CP/M-86 became an option for the IBM PC after DRI threatened legal action, it never overtook Microsoft's system.
When Digital Equipment Corporation put out the Rainbow 100 to compete with IBM, it came with CP/M-80 using a Z80 chip, CP/M-86 or MS-DOS using an 8088 microprocessor, or CP/M-86/80 using both. The Z80 and 8088 CPUs ran concurrently. A benefit of the Rainbow was that it could continue to run 8-bit CP/M software, preserving a user's possibly sizable investment as they moved into the 16-bit world of MS-DOS.
CP/M-68K, already running on the Motorola EXORmacs systems, was initially to be used in the Atari ST computer, but Atari decided to go with a newer disk operating system called GEMDOS. CP/M-68K was also used on the SORD M68 and M68MX computers.
These 16-bit versions of CP/M required application programs to be re-compiled for the new CPUs—or, if they were written in assembly language, to be translated using tools like Digital Research's XLT86, a program written by Gary Kildall in 1981, which translated .ASM source code for the Intel 8080 processor into .A86 source code for the Intel 8086. Using global data flow analysis on 8080 register usage, the translator would also optimize the output for code size and take care of calling conventions, so that CP/M-80 and MP/M-80 programs could be ported to the CP/M-86 and MP/M-86 platforms automatically. XLAT86 itself was written in PL/I-80 and was available for CP/M-80 platforms as well as for DEC VMS (for VAX 11/750 or 11/780).
MS-DOS takes over
Many expected that CP/M would be the standard operating system for 16-bit computers. In 1980 IBM approached Digital Research, at Bill Gates' suggestion, to license a forthcoming version of CP/M for its new product, the IBM Personal Computer. Upon the failure to obtain a signed non-disclosure agreement, the talks failed, and IBM instead contracted with Microsoft to provide an operating system. The resulting product, MS-DOS, soon began outselling CP/M.
Many of the basic concepts and mechanisms of early versions of MS-DOS resembled those of CP/M. Internals like file-handling data structures were identical, and both referred to disk drives with a letter (
B:, etc.). MS-DOS's main innovation was its FAT file system. This similarity made it easier to port popular CP/M software like WordStar and dBase. However, CP/M's concept of separate user areas for files on the same disk was never ported to MS-DOS. Since MS-DOS had access to more memory (as few IBM PCs were sold with less than 64 KB of memory, while CP/M could run in 16 KB if necessary), more commands were built into the command-line shell, making MS-DOS somewhat faster and easier to use on floppy-based computers.
Although one of the first peripherals for the IBM PC was a SoftCard-like expansion card that let it run 8-bit CP/M software, CP/M rapidly lost market share as the microcomputing market moved to the IBM-compatible platform, and it never regained its former popularity. Byte magazine, at the time one of the leading industry magazines for microcomputers, essentially ceased covering CP/M products within a few years of the introduction of the IBM PC. For example, in 1983 there were still a few advertisements for S100 boards and articles on CP/M software, but by 1987 these were no longer found in the magazine. InfoWorld described the unsuccessful efforts at introducing CP/M based home computers in 1983 and in 1986 stated that Kaypro had stopped production of their 8-bit CP/M-based models to concentrate on sales of MS-DOS compatible systems, long after most other vendors had ceased production of new equipment and software for CP/M.
Later versions of CP/M-86 made significant strides in performance and usability and were made compatible with MS-DOS. To reflect this compatibility the name was changed, and CP/M-86 became DOS Plus, which in turn became DR-DOS.
ZCPR (the Z80 Command Processor Replacement) was introduced on February 2, 1982 as a drop-in replacement for the standard Digital Research console command processor (CCP) and was initially written by a group of computer hobbyists who called themselves "The CCP Group". They were Frank Wancho, Keith Petersen (the archivist behind Simtel at the time), Ron Fowler, Charlie Strom, Bob Mathias, and Richard Conn. Richard was, in fact, the driving force in this group (all of whom maintained contact through email).
ZCPR1 was released on a disk put out by SIG/M (Special Interest Group/Microcomputers), a part of the Amateur Computer Club of New Jersey.
ZCPR2 was released on February 14, 1983. It was released as a set of ten disks from SIG/M. ZCPR2 was upgraded to 2.3, and also was released in 8080 code, permitting the use of ZCPR2 on 8080 and 8085 systems.
ZCPR3 was released on Bastille Day, July 14, 1984, as a set of nine disks from SIG/M. The code for ZCPR3 could also be compiled (with reduced features) for the 8080 and would run on systems that did not have the requisite Z80 microprocessor.
In January 1987, Richard Conn stopped developing ZCPR, and Echelon asked Jay Sage (who already had a privately enhanced ZCPR 3.1) to continue work on it. Thus, ZCPR 3.3 was developed and released. ZCPR33 no longer supported the 8080 series of microprocessors, and added the most features of any upgrade in the ZCPR line.
Features of ZCPR as of version 3 included:
- I/O redirection
- flow control
- named directories
- search paths
- custom menus
- on line help
ZCPR3.3 also included a full complement of utilities with considerably extended capabilities. While enthusiastically supported by the CP/M user base of the time, ZCPR alone was insufficient to slow the demise of CP/M.
A number of behaviors exhibited by Microsoft Windows are a result of backward compatibility to MS-DOS, which in turn attempted some backward compatibility with CP/M. The drive letter and 8.3 filename conventions in MS-DOS (and early Windows versions) were originally adopted from CP/M. The wildcard matching characters used by Windows (? and *) are based on those of CP/M, as are the reserved filenames used to redirect output to a printer ("PRN:"), and the console ("CON:"). The drive names A and B were used to designate the 2 floppy disk drives that CP/M systems typically used; when hard drives appeared they were designated C, which survived into MS-DOS as the
C:\> command prompt. Also, the control character marking the end of some text files can also be attributed to CP/M.
Source code releases
In 2001 Caldera released CP/M's source code under an open source license, allowing redistribution and modification, via Tim Olmstead's "The Unofficial CP/M Web site". In October 2014, to mark the 40th anniversary of the first presentation of CP/M, the Computer History Museum released early source code versions of CP/M.
- Eagle Computer
- List of machines running CP/M
- Multiuser DOS
- Amstrad CP/M Plus character set
- CP/M collection is back online with an Open Source licence Archived 2017-09-01 at the Wayback Machine. The Register, November 26, 2001
- Mann, Stephen (1983-08-15). "CP/M Plus, a third, updated version of CP/M". InfoWorld. 5 (33): 49ff. ISSN 0199-6649.
- Shustek, Len (2016-08-02). "In His Own Words: Gary Kildall". Remarkable People. Computer History Museum. Archived from the original on 2016-12-17.
- Kildall, Gary Arlen (2016-08-02) . Kildall, Scott; Kildall, Kristin, eds. "Computer Connections: People, Places, and Events in the Evolution of the Personal Computer Industry" (Manuscript, part 1). Kildall Family. Archived from the original on 2016-11-17. Retrieved 2016-11-17.
- Newton, Harry (2000). Newton's Telecom Dictionary. New York, NY: CMP Books. p. 228. ISBN 1-57820-053-9.
- "OLDCOMPUTERS.COM Compupro 8/16". Archived from the original on 2016-01-03.
- Cole, Maggie (1981-05-25). "Gary Kildall and the Digital Research Success Story". InfoWorld. Palo Alto, CA. 3 (10): 52–53. ISSN 0199-6649.
- Freiberger, Paul (1982-07-05). "History of microcomputing, part 3: software genesis". InfoWorld. Palo Alto, CA. 4 (26): 41. ISSN 0199-6649.
- "The Official Book for the Commodore 128".
Since CP/M was one of the first operating systems, a large number of hobbyists, hackers, and esoteric programmers purchased CP/M computers and began to write programs for themselves... It was offered on the free market in the form of floppy disks distributed at computer "user groups".
- "CP/M emulators for DOS". www.retroarchive.org/cpm. Luis Basto. Archived from the original on 2016-07-09. Retrieved 2016-07-06.
- Kildall, Gary A. (June 1975), CP/M 1.1 or 1.2 BIOS and BDOS for Lawrence Livermore Laboratories,
An excerpt of the BDOS.PLM file header in the PL/M source code of CP/M 1.1 or CP/M 1.2 for Lawrence Livermore Laboratories (LLL):
[...] /* C P / M B A S I C I / O S Y S T E M (B I O S) COPYRIGHT (C) GARY A. KILDALL JUNE, 1975 */ [...] /* B A S I C D I S K O P E R A T I N G S Y S T E M (B D O S) COPYRIGHT (C) GARY A. KILDALL JUNE, 1975 */ [...]
- Kildall, Gary A. (January 1980). "The History of CP/M, THE EVOLUTION OF AN INDUSTRY: ONE PERSON'S VIEWPOINT". Dr. Dobb's Journal of Computer Calisthenics & Orthodontia. pp. 6–7. Archived from the original on 2016-11-24. Retrieved 2013-06-03.
[...] The first commercial licensing of CP/M took place in 1975 with contracts between Digital Systems and Omron of America for use in their intelligent terminal, and with Lawrence Livermore Laboratories where CP/M was used to monitor programs in the Octopus network. Little attention was paid to CP/M for about a year. In my spare time, I worked to improve overall facilities [...] By this time, CP/M had been adapted for four different controllers. [...] In 1976, Glenn Ewing approached me with a problem: Imsai, Incorporated, for whom Glenn consulted, had shipped a large number of disk subsystems with a promise that an operating system would follow. I was somewhat reluctant to adapt CP/M to yet another controller, and thus the notion of a separated Basic I/O System (BIOS) evolved. In principle, the hardware dependent portions of CP/M were concentrated in the BIOS, thus allowing Glenn, or anyone else, to adapt CP/M to the Imsai equipment. Imsai was subsequently licensed to distribute CP/M version 1.3 which eventually evolved into an operating system called IMDOS. [...]
- "CP/M Builtin Commands". discordia.org.uk. Archived from the original on 2008-04-12. Retrieved 2009-01-28.
- "CP/M Dynamic Debugging Tool", "Archived copy". Archived from the original on 2015-06-17. Retrieved 2014-08-29.; "Archived copy" (PDF). Archived (PDF) from the original on 2014-10-28. Retrieved 2014-08-29.; "Archived copy". Archived from the original on 2015-12-08. Retrieved 2014-08-29., all retrieved 2014-08-29
- "Whole Earth Software Catalog". Archived from the original on 2015-07-04.
- CP/M Plus (CP/M Version 3) Operating System Programmers Guide (PDF) (2 ed.). Digital Research. April 1983 [January 1983]. Archived (PDF) from the original on 2016-11-25. Retrieved 2016-11-25.
- Lieber, Eckhard; von Massenbach, Thomas (1987). "CP/M 2 lernt dazu. Modulare Systemerweiterungen auch für das 'alte' CP/M". c't (part 1) (in German). Heise Verlag (1): 124–135.
- Lieber, Eckhard; von Massenbach, Thomas (1987). "CP/M 2 lernt dazu. Modulare Systemerweiterungen auch für das 'alte' CP/M". c't (part 2) (in German). Heise Verlag (2): 78–85.
- Huck, Alex (2016-10-09). "RSM für CP/M 2.2" (in German). Archived from the original on 2016-11-25. Retrieved 2016-11-25.
- Johnson, Herbert (2009-01-04). "CP/M and Digital Research Inc. (DRI) History". www.retrotechnology.com. Archived from the original on 2008-08-20. Retrieved 2009-01-28.
- Warren, Jim (April 1976). "First word on a floppy-disk operating system". Dr. Dobb's Journal. Menlo Park, CA. 1 (4): 5. Subtitle: Command language & facilities similar to DECSYSTEM-10.
- Digital Research (1978). "CP/M". Pacific Grove, Calif.: Digital Research. OCLC 221485970. Archived from the original on 2016-03-23.
- Wise, Deborah (1982-05-10). "Mainframe makers court third-party vendors for micro software". InfoWorld. pp. 21–22. Archived from the original on 2015-03-18. Retrieved 2015-01-25.
- da Cruz, Frank (1984-04-27). "New release of KERMIT for CP/M-80". Info-Kermit Digest (Mailing list). Kermit Project, Columbia University. Retrieved 2016-02-23.
- Swaine, Michael (1997-04-01). "Gary Kildall and Collegial Entrepreneurship". Dr. Dobb's Journal. Archived from the original on 2007-01-24. Retrieved 2006-11-20.
- Bunnell, David (February 1982). "The Man Behind The Machine? / A PC Exclusive Interview With Software Guru Bill Gates". PC Magazine. p. 16. Archived from the original on 2013-05-09. Retrieved 2012-02-17.
- Mace, Scott (9–16 January 1984). "IBM PC clone makers shun total compatibility". InfoWorld. pp. 79–81. Archived from the original on 16 March 2015. Retrieved 2015-02-04.
- Pournelle, Jerry (June 1983). "Zenith Z-100, Epson QX-10, Software Licensing, and the Software Piracy Problem". BYTE. 8 (6). p. 411. Archived from the original on 2014-06-09. Retrieved 2013-10-20.
- Loguidice, Bill (2012-07-28). "More on Avalon Hill Computer Games on Heath/Zenith platforms". Armchair Arcade. Archived from the original on 2015-07-23. Retrieved 2015-07-22.
- Sblendorio, Francesco (2015-12-01). "Gorillas for CP/M". Archived from the original on 2016-02-05. Retrieved 2015-07-22.
- Pournelle, Jerry (April 1982). "The Osborne 1, Zeke's New Friends, and Spelling Revisited". BYTE. p. 212. Archived from the original on October 26, 2013. Retrieved October 19, 2013.
- Johnson-Laird, Andy (1983). "3". The programmer's CP/M handbook. Berkeley, CA: Osborne/McGraw-Hill. ISBN 0-88134-103-7.
- "Now: A Complete CP/M Pascal for Only $29.95!". BYTE (advertisement). December 1982. p. 11. Archived from the original on 2016-07-21. Retrieved 2016-10-01.
- Derfler, Frank J. (1982-10-18). "Kaypro II—a low-priced, 26-pound portable micro". InfoWorld. p. 59. Archived from the original on 2014-01-01. Retrieved 2013-10-22.
- Fager, Roger; Bohr, John (September 1983). "The Kaypro II". BYTE. p. 212. Archived from the original on 2014-03-02. Retrieved 2013-10-20.
- "Radio Shack Computer Catalog RSC-12 page 28". www.radioshackcomputercatalogs.com. Tandy/Radio Shack. Archived from the original on 2016-10-13. Retrieved 2016-07-06.
- Olmstead, Tim; Chaudry, Gaby. "Digital Research Source Code". Archived from the original on 2016-02-05.
- Kildall, Gary Arlen (1982-09-16). "Running 8-bit software on dual-processor computers" (PDF). Electronic Design: 157. Archived (PDF) from the original on 2017-08-19. Retrieved 2017-08-19.
- Snyder, John J. (June 1983). "A DEC on Every Desk?". BYTE. pp. 104–106. Archived from the original on 2015-01-02. Retrieved 2015-02-05.
- "M 68 / M 68 MX". Archived from the original on 2016-03-06.
- Digital Research (1981): XLT86 - 8080 to 8086 Assembly Language Translator - User's Guide Archived 2016-11-18 at the Wayback Machine.. Digital Research Inc, Pacific Grove
- Pournelle, Jerry (March 1984). "New Machines, Networks, and Sundry Software". BYTE. p. 46. Archived from the original on 2015-02-02. Retrieved 2013-10-22.
- Walter Isaacson, The Innovators: How a Group of Inventors, Hackers, Geniuses, and Geeks Created the Digital Revolution (2014, Simon & Schuster, ISBN 978-1476708690), page 358
- Mary Bellis, Inventors of the Modern Computer Series, The History of the MS-DOS Operating Systems, Microsoft, Tim Paterson, and Gary Kildall (accessed Sept 9, 2010)
- Magid, Lawrence J. (February 1982). "Baby Blue". PC. p. 49. Archived from the original on 2015-03-18. Retrieved 2015-01-04.
- Scott Mace, CP/M Eludes Home Market, InfoWorld, June 1984 page 46
- Nancy Groth, Kaypro is retreating on CP/M, InfoWorld February 1986, page 6
- Chen, Raymond. "Why does MS-DOS use 8.3 filenames instead of, say, 11.2 or 16.16?". The Old New Thing. Archived from the original on 2011-09-22. Retrieved 2010-12-17.
- Chen, Raymond. "How did wildcards work in MS-DOS?". The Old New Thing. Archived from the original on 2011-05-08. Retrieved 2010-12-17.
- Chen, Raymond. "What's the deal with those reserved filenames like NUL and CON?". The Old New Thing. Archived from the original on 2010-08-02. Retrieved 2010-12-17.
- Chen, Raymond. "Why do text files end in Ctrl+Z?". The Old New Thing. Archived from the original on 2011-02-06. Retrieved 2010-12-17.
- "The Unofficial CP/M Web Site". Archived from the original on 2016-02-03.
- "CP/M Collection is Back Online with an Open Source Licence". The Register. 2001-11-26. Archived from the original on 2017-09-01.
- "License Agreement". Archived from the original on 2015-09-24.
- "License Agreement". Archived from the original on 2015-09-14.
- Laws, David (2014-10-01). "Early Digital Research CP/M Source Code". Computer History Museum. Archived from the original on 2015-07-27. Retrieved 2015-07-25.
- ZCPR3, The Manual by Richard Conn: ISBN 0-918432-59-6
- comp.os.cpm FAQ (also present at this Digital Research related site)
- Z-System Corner: Tenth Anniversary of ZCPR - part of The Computer Journal, issue 54
|Wikimedia Commons has media related to CP/M.|
- Digital Research official CP/M page
- The origin of CP/M's name at the Wayback Machine (archived June 11, 2008)
- The origin of CP/M's name
- CP/M at Curlie (based on DMOZ)
- CP/M Main Page - Technical information site
- CP/M Internals - CP/M internals
- The Unofficial CP/M Web site - Includes source code
- Triumph of the Nerds - This PBS series includes the details of IBM's choice of Microsoft DOS over Digital Research's CP/M for the IBM PC
- Gaby's Homepage for CP/M and Computer History - includes ZCPR materials
- N8VEM Google Group - An active group (2009) building open source CP/M boards, peripherals and wireless links.
- "Create a complete CP/M machine with RS-232 port using only 9 ICs". Archived from the original on 2012-06-20. Retrieved 2010-01-24. - By Grant Searle
- Intel iPDS-100 Using CP/M-Video