Rockwell X-30
| X-30 NASP | |
|---|---|
| |
| Artist's Concept of the X-30 entering orbit | |
| Role | SSTO aerospaceplane |
| Manufacturer | Rockwell International |
| Status | Cancelled 1993 |
| Primary user | NASA |
| Number built | 0 |
| Developed into | X-43 |
The X-30 National Aero-Space Plane (NASP) was a United States project to create a single-stage-to-orbit (SSTO) spacecraft. It was cancelled before a prototype was built.
Development
NASP came from the "Copper Canyon" project, in Defense Advanced Research Projects Agency (DARPA), running from 1982 to 1985. In his 1986 State of the Union address, President Ronald Reagan called for "a new Orient Express that could, by the end of the next decade, take off from Dulles Airport, accelerate up to 25 times the speed of sound, attaining low earth orbit or flying to Tokyo within two hours."
Research suggested a maximum speed of Mach 8 for scramjet based aircraft, as the vehicle would generate heat due to atmospheric friction, which would thus cost considerable energy. The project showed that much of this energy could be recovered by passing hydrogen over the skin and carrying the heat into the combustion chamber: Mach 20 then seemed possible. The result was a program funded by NASA, and the United States Department of Defense (funding was approximately equally divided between NASA, DARPA, the US Air Force, the Strategic Defense Initiative Office (SDIO) and the US Navy).[1]
McDonnell Douglas, Rockwell International, and General Dynamics competed to develop technology for a hypersonic air-breathing SSTO vehicle. Rocketdyne and Pratt & Whitney competed to develop engines.
In 1990, the companies joined under the leadership of Rockwell International to develop the craft to deal with the technical and budgetary obstacles. Development on the X-30, as it was then designated, continued until 1993, when it was terminated amid budget cuts and technical concerns.
Design
The X-30 configuration was a highly integrated engine. The shovel-shaped forward fuselage generated a shock wave to compress air before it entered the engine. The aft fuselage formed an integrated nozzle to expand the exhaust. The engine between was a scramjet engine. At the time, however, no scramjet engine of the kind was close to operational.
The aerodynamic configuration was an example of a waverider. Most of the lift was generated by the fuselage by compression lift. The "wings" were small fins providing trim and control. This configuration was efficient for high-speed flight, but would have made take-off and slow-speed flight difficult.
Temperatures on the airframe were expected to be 1800 °F (980 °C) over a large part of the surface, with maximums of over 3000 °F (1650 °C) on the leading edges and portions of the engine. This required the development of high temperature lightweight materials, including alloys of titanium and aluminum called gamma and alpha titanium aluminide, advanced carbon/carbon composites, and titanium metal matrix composite (TMC) with silicon carbide fibers. Titanium matrix composites were used by McDonnell Douglas to create a representative fuselage section called "Task D". The Task D test article was four feet high by eight feet wide by eight feet long. A carbon/epoxy cryogenic hydrogen tank was integrated with the fuselage section and the whole assembly, including volatile and combustible hydrogen, was successfully tested with mechanical loads and a temperature of 1500 °F (820 °C) in 1992, just before program cancellation.
Despite progress in developing the necessary structural and propulsion technology, NASA still had substantial hurdles to overcome. The Department of Defense wanted it to carry a crew of two and even a small payload. The demands of being a man-rated vehicle, with the instrumentation, environmental control system, and safety equipment, made X-30 larger, heavier, and more expensive than required for a technology demonstrator. The result was a cancellation of the X-30 and a move toward a more modest hypersonic program that culminated in the unmanned X-43 "Hyper-X", which is virtually an unmanned scaled-down X-30. A large, detailed scale mock up of the X-30 was built by engineering students at Mississippi State University's Raspet Flight Research Lab in Starkville, Mississippi. The mock-up is on display at the Aviation Challenge campus of the U.S. Space Camp facility in Huntsville, Alabama.
Specifications (X-30 as designed)
 |
This aircraft article is missing some (or all) of its specifications. If you have a source, you can help Wikipedia by adding them. |
General characteristics
- Length: 314.0 ft (95.7 m)
- Diameter: 52.0 ft (15.8 m)
- Empty weight: 132,000 lb (59,874 kg)
- Gross weight: 300,000 lb (136,078 kg)
- Powerplant: 1 × Scramjet , 314,700 lbf (1,400 kN) thrust
Performance
- Maximum speed: 23,000 mph (37,000 km/h, 20,000 kn)
- Maximum speed: Mach 30indefinite (orbital)
- Service ceiling: 1,500,000 ft (460,000 m)
- Wing loading: 200 lb/sq ft (980 kg/m2) (Takeoff), 40 lb/ft² (950 kg/m²) (Reentry)
- Thrust/weight: 1.049
- Stage 1: 1 x X-30.
- Isp: 1,550 sec
- Burn time: 886 sec
- Propellants: Air/Slush LH2 [1]
See also
Aircraft of comparable role, configuration, and era
- NASA X-43 (essentially a down-scaled model)
- Tupolev Tu-2000
- HOTOL
References
American X-Vehicles (.pdf)
External links
