Simultaneous multithreading
![]() |
Simultaneous multithreading, often abbreviated as SMT, is a technique for improving the overall efficiency of superscalar CPUs with hardware multithreading. SMT permits multiple independent threads of execution to better utilize the resources provided by modern processor architectures.
Details
Multithreading is similar in concept to preemptive multitasking but is implemented at the thread level of execution in modern superscalar processors.
Simultaneous multithreading (SMT) is one of the two main implementations of multithreading, the other form being temporal multithreading. In temporal multithreading, only one thread of instructions can execute in any given pipeline stage at a time. In simultaneous multithreading, instructions from more than one thread can be executing in any given pipeline stage at a time. This is done without great changes to the basic processor architecture: the main additions needed are the ability to fetch instructions from multiple threads in a cycle, and a larger register file to hold data from multiple threads. The number of concurrent threads can be decided by the chip designers, but practical restrictions on chip complexity have limited the number to two for most SMT implementations.
Because the technique is really an efficiency solution and there is inevitable increased conflict on shared resources, measuring or agreeing on the effectiveness of the solution can be difficult. Some researchers have shown that the extra threads can be used to proactively seed a shared resource like a cache, to improve the performance of another single thread, and claim this shows that SMT is not just an efficiency solution. Others use SMT to provide redundant computation, for some level of error detection and recovery.
However, in most current cases, SMT is about hiding memory latency, efficiency and increased throughput of computations per amount of hardware used.
Taxonomy
In processor design, there are two ways to increase on-chip parallelism with less resource requirements: one is superscalar technique which tries to increase Instruction Level Parallelism (ILP), the other is multithreading approach exploiting Thread Level Parallelism (TLP).
Superscalar means executing multiple instructions at the same time while chip-level multithreading (CMT) executes instructions from multiple threads within one processor chip at the same time. There are many ways to support more than one thread within a chip, namely:
- Interleaved multithreading: Interleaved issue of multiple instructions from different threads, also referred to as Temporal multithreading. It can be further divided into fine-grain multithreading or coarse-grain multithreading depending on the frequency of interleaved issues. Fine-grain multithreading -- such as in a barrel processor -- issues instructions for different threads after every cycle, while coarse-grain multithreading only switches to issue instructions from another thread when the current executing thread causes some long latency events (like page fault etc.). Coarse-grain multithreading is more common for less context switch between threads. For example, Intel's Montecito processor uses coarse-grain multithreading, while Sun's UltraSPARC T1 uses fine-grain multithreading. For those processors that have only one pipeline per core, interleaved multithreading is the only possible way, because it can issue at most one instruction per cycle.
- Simultaneous multithreading (SMT): Issue multiple instructions from multiple threads in one cycle. The processor must be superscalar to do so.
- Chip-level multiprocessing (CMP or multicore): integrates two or more superscalar[citation needed] processors into one chip, each executes threads independently
- Any combination of multithreaded/SMT/CMP
The key factor to distinguish them is to look at how many instructions the processor can issue in one cycle and how many threads from which the instructions come. For example, Sun Microsystems' UltraSPARC T1 (known as "Niagara" until its November 14, 2005 release) is a multicore processor combined with fine-grain multithreading technique instead of simultaneous multithreading because each core can only issue one instruction at a time.
Historical implementations
While multithreading CPUs have been around since the 1950s, simultaneous multithreading was first researched by IBM in 1968. The first major commercial microprocessor developed with SMT was the Alpha 21464 (EV8). This microprocessor was developed by DEC in coordination with Dean Tullsen of the University of California, San Diego, and Susan Eggers and Hank Levy of the University of Washington. The microprocessor was never released, since the Alpha line of microprocessors was discontinued shortly before HP acquired Compaq which had in turn acquired DEC. Dean Tullsen's work was also used to develop the "Hyper-threading" (or "HTT") versions of the Intel Pentium 4 microprocessors, such as the "Northwood" and "Prescott".
Modern commercial implementations
The Intel Pentium 4 was the first modern desktop processor to implement simultaneous multithreading, starting from the 3.06GHz model released in 2002, and since introduced into a number of their processors. Intel calls the functionality Hyper-Threading Technology (HTT), and provides a basic two-thread SMT engine. Intel claims up to a 30% speed improvement compared against an otherwise identical, non-SMT Pentium 4. The performance improvement seen is very application dependent, and some programs actually slow down slightly when HTT is turned on due to increased contention for resources such as bandwidth, caches, TLBs, re-order buffer entries, etc. This is generally the case for poorly written data access routines that cause high latency intercache transactions (cache thrashing) on multi-processor systems. Programs written before multiprocessor and multicore designs were prevalent commonly did not optimize cache access because on a single CPU system there is only a single cache which is always coherent with itself. On a multiprocessor system each CPU or core will typically have its own cache, which is interlinked with the cache of other CPU/cores in the system to maintain cache coherency. If thread A accesses a memory location [00] and thread B then accesses memory location [01] it can cause an intercache transaction particularly where the cache line fill exceeds 2 bytes, as is the case for all modern processors.
The latest MIPS architecture designs include an SMT system known as "MIPS MT". MIPS MT provides for both heavyweight virtual processing elements and lighter-weight hardware microthreads. RMI, a Cupertino-based startup, is the first MIPS vendor to provide a processor SOC based on 8 cores, each of which runs 4 threads. The threads can be run in fine-grain mode where a different thread can be executed each cycle. The threads can also be assigned priorities.
The IBM POWER5, announced in May 2004, comes as either a dual core DCM, or quad-core or oct-core MCM, with each core including a two-thread SMT engine. IBM's implementation is more sophisticated than the previous ones, because it can assign a different priority to the various threads, is more fine-grained, and the SMT engine can be turned on and off dynamically, to better execute those workloads where an SMT processor would not increase performance. This is IBM's second implementation of generally available hardware multithreading.
Although many people reported that Sun Microsystems' UltraSPARC T1 (known as "Niagara" until its 14 November 2005 release) and the upcoming processor codenamed "Rock" (to be launched ~2009 [1]) are implementations of SPARC focused almost entirely on exploiting SMT and CMP techniques, Niagara is not actually using SMT. Sun refers to these combined approaches as "CMT", and the overall concept as "Throughput Computing". The Niagara has 8 cores, but each core has only one pipeline, so actually it uses fine-grained multithreading. Unlike SMT, where instructions from multiple threads share the issue window each cycle, the processor uses a round robin policy to issue instructions from the next active thread each cycle. This makes it more similar to a barrel processor. Sun Microsystems' Rock processor is different, it has more complex cores that have more than one pipeline.
The Intel Atom, released in 2008, is the first Intel product to feature SMT (marketed as Hyper-Threading) without supporting instruction reordering, speculative execution, or register renaming. Intel reintroduced Hyper-Threading with the Nehalem microarchitecture, after its absence on the Core microarchitecture.
Disadvantages
Simultaneous multithreading cannot improve performance if any of the shared resources are limiting bottlenecks for the performance. In fact, some applications run slower when simultaneous multithreading is enabled. Critics argue that it is a considerable burden to put on software developers that they have to test whether simultaneous multithreading is good or bad for their application in various situations and insert extra logic to turn it off if it decreases performance. Current operating systems lack convenient API calls for this purpose and for preventing processes with different priority from taking resources from each other [2].
There is also a security problem with simultaneous multithreading. It has been proven that it is possible for one application to steal a cryptographic key from another application running in the same processor by monitoring its cache use [3].
See also
- Temporal multithreading, another implementation of hardware multithreading
- Thread (computer science), the fundamental software entity scheduled by the operating system kernel to execute on a CPU or processor (core)
- Symmetric multiprocessing, where the system (or partition of a larger computer hardware platform) contains more than one CPU or processor (core) and where the operating system kernel is not limited to which of the available CPUs (cores) a given thread can be scheduled to execute on
References
- LE Shar and ES Davidson, "A Multiminiprocessor System Implemented through Pipelining", Computer Feb 1974
- D.M. Tullsen, S.J. Eggers, and H.M. Levy, "Simultaneous Multithreading: Maximizing On-Chip Parallelism," In 22nd Annual International Symposium on Computer Architecture, June, 1995
- D.M. Tullsen, S.J. Eggers, J.S. Emer, H.M. Levy, J.L. Lo, and R.L. Stamm, "Exploiting Choice: Instruction Fetch and Issue on an Implementable Simultaneous Multithreading Processor," In 23rd Annual International Symposium on Computer Architecture, May, 1996