Flush toilet

"Water closet" redirects here. For the room in a house with only a toilet, see Toilet (room). For rooms labelled "W.C.", see Public toilet.

Flush toilets can be designed for sitting or for squatting: Top: A flush toilet designed for sitting and cistern; Bottom: A squat toilet, with water tank for flushing (Wuhan, China)

A flush toilet (also known as a flushing toilet, flush lavatory, water closet (WC), or commode in colloquial US English) is a toilet that disposes of human excreta (urine and feces) by using water to flush it through a drainpipe to another location for disposal, thus maintaining a separation between humans and their excreta. Flush toilets can be designed for sitting (in which case they are also called "Western" toilets) or for squatting, in the case of squat toilets. The opposite of a flush toilet is a dry toilet, which uses no water for flushing.

Flush toilets are a type of plumbing fixture and usually incorporate an "S", "U", "J", or "P" shaped bend (called a trap, such as P trap or S trap) that causes the water in the toilet bowl to collect and act as a seal against sewer gases (trapping the gases). Since flush toilets are typically not designed to handle waste on site, their drain pipes must be connected to waste conveyance and waste treatment systems. When a toilet is flushed, the wastewater flows into a septic tank or sewage system and from there to a sewage treatment plant.

A flush toilet is different from a urinal, which is designed to handle only urine; and from a bidet, which can be used for cleansing of the anus, perineum, and genitals after using the toilet.

Operation

A flush toilet bowl during the flushing action

Typical sound of a flush toilet

A typical flush toilet is a fixed, vitreous ceramic bowl (also known as a pan) which is connected to a drain. After use, the bowl is emptied and cleaned by the rapid flow of water into the bowl. This flush may flow from a dedicated tank (cistern), a high-pressure water pipe controlled by a flush valve, or by manually pouring water into the bowl. Tanks and valves are normally operated by the user, by pressing a button, pulling a lever or pulling a chain. The water is directed around the bowl by a molded flushing rim around the top of the bowl or by one or more jets, so that the entire internal surface of the bowl is rinsed with water.

Mechanical flush from a cistern

A typical toilet has a tank fixed above the bowl which contains a fixed volume of water. When the user operates the flush, the entire contents of the tank are discharged rapidly into the toilet bowl, causing the contents of the bowl to be swept or sucked out of the toilet and into the drain. The water may be discharged through a "toilet flapper valve" (not to be confused with a type of check valve) or through a siphon. At the end of the flush, an automatic valve opens to allow the tank to be refilled ready for the next flush.

Mechanical flush from a high pressure water supply

Toilets without cisterns are often flushed through a simple flush valve or "Flushometer" connected directly to the water supply. These are designed to rapidly discharge a limited volume of water when the lever or button is pressed then released.

Manual flush (pour flush)

Another variant of the flush toilet is the pour-flush toilet. This type of flush toilet has no cistern or permanent water supply, but is flushed manually with a few litres of a small bucket. The flushing can use as little as 2–3 litres. This type of toilet is common in many Asian countries. The toilet can be connected to one or two pits, in which case it is called a "pour flush pit latrine" or a "twin pit pour flush pit latrine". It can also be connected to a septic tank.

Flushing systems

The flushing system provides a large flow of water into the bowl. They normally take the form of either fixed tanks of water or flush valves.

Flush tanks

Flush tanks or cisterns usually incorporate a mechanism to release water from the tank and an automatic valve to allow the cistern to be refilled automatically.

This system is suitable for locations plumbed with 1⁄2 inch (13 mm) or 3⁄8 inch (9.5 mm) water pipes which cannot supply water quickly enough to flush the toilet; the tank is needed to supply a large volume of water in a short time. The tank typically collects between 6 and 17 litres (1.3 and 3.7 imp gal; 1.6 and 4.5 US gal) of water over a period of time. The storage tank is usually mounted directly upon the bowl, although some tanks are mounted on the wall a few feet above the bowl in an attempt to increase the flush water pressure as it enters the bowl. Tanks near the ceiling are flushed by means of a dangling pull chain, often with a large ornate handle, connected to a flush lever on the cistern itself. "Pulling the chain" remains a British euphemism for flushing the toilet, although this type of tank or cistern is becoming rare. A similar German expression is Wasser ziehen ("to pull water").

Older installations, known as "high suite combinations", used a high-level cistern (tank), fitted above head height. When more modern close-coupled cistern and bowl combinations were first introduced, these were first referred to as "low suite combinations". Modern versions have a neater-looking low-level cistern with a lever that the user can reach directly, or a close-coupled cistern that is even lower down and fixed directly to the bowl. In recent decades the close coupled tank/bowl combination has become the most popular residential system, as it has been found by ceramic engineers that improved waterway design is a more effective way to enhance the bowl's flushing action than high tank mounting.

Tank fill valve

The ballcock or float valve is often used to regulate the filling of a tank or cistern. When the fluid level drops, the float descends, levering the valve opening and allowing more fluid to enter. Once the float reached the 'full' position, the arm presses the valve shut again.

Tank fill valves are found in all tank-style toilets. The valves are of two main designs: the side-float design and the concentric-float design. The side-float design has existed for over a hundred years. The concentric design has only existed since 1957, but is gradually becoming more popular than the side-float design.

The side-float design uses a float on the end of a lever to control the fill valve. The float is usually shaped like a ball, so the mechanism is often called a ball-valve or a ballcock (cock in his context is an alternative term for valve; see, for example, stopcock). The float was originally made from copper sheet, but it is now usually plastic. The float is located to one side of the main valve tower or inlet at the end of a rod or arm. As the float rises, so does the float-arm. The arm connects to the fill valve that blocks the water flow into the toilet tank, and shuts off the water when the float reaches a set height. This maintains a constant level in the tank.

One type of concentric float valve. The concentric float valve opens when the fluid level is low, allowing more fluid to enter (Figure 1). When the fluid level returns to the full level, the valve is shut (Figure 2).

The newer concentric-float fill valve consists of a tower which is encircled by a plastic float assembly. Operation is otherwise the same as a side-float fill valve, even though the float position is somewhat different. By virtue of its more compact layout, interference between the float and other obstacles (tank insulation, flush valve, and so on) is greatly reduced, thus increasing reliability. The concentric-float fill valve is also designed to signal to users automatically when there is a leak in the tank, by making much more noise when a leak is present than the older style side-float fill valve, which tends to be nearly silent when a slow leak is present.

Flapper-flush valve

In tanks using a flapper-flush valve, the outlet at the bottom of the tank is covered by a buoyant (plastic or rubber) cover, or flapper, which is held in place against a fitting (the flush valve seat) by water pressure. To flush the toilet, the user pushes a lever, which lifts the flush valve from the valve seat. The valve then floats clear of the seat, allowing the tank to empty quickly into the bowl. As the water level drops, the floating flush valve descends back to the bottom of the tank and covers the outlet pipe again. This system is common in homes in the US and in continental Europe. Recently this flush system has also become available in the UK due to a change in regulations.

Dual flush versions of this design are now widely available. They have one level of water for liquid waste and a higher level for solid waste. In countries such as Australia, Israel, Singapore or Germany which either have limitations on water consumption or where people are keen to save water, dual flush toilets are now common in both homes and public washrooms.

Siphon-flush mechanism

A simplified diagram of a siphonic WC cistern. The siphon is formed of a vertical pipe (1) that links the flush pipe (2) to a domed chamber (3). A perforated disc (4) covered by a flexible plate or flap (5) is joined by the siphon rod (6) to the flush lever (7).

This system, invented by Albert Giblin and common in the UK, uses a storage tank similar to that used in the flapper-flush-valve system above. This flush valve system is sometimes referred to as a valveless system, since no traditional type of valve is required. Some would argue, however, that any system of regulating the flow of a fluid is still technically a valve.

The siphon is formed of a vertical pipe that links the flush pipe to a domed chamber inside the cistern. A perforated disc, covered by a flexible plate or flap, is fitted inside this chamber and is joined by a rod to the flush lever.

Pressing the lever raises the disc, forces water over the top of the siphon into the vertical pipe, and starts the siphonic flow. Water flows through the peforated disc past the flap until the cistern is empty, at which point air enters the siphon and the flush stops.

The advantage of a siphon over the flush valve is that it has no sealing washers that can wear out and cause leaks, so it is favoured in places where there is a need to conserve water.

Until 1 January 2001, the use of siphon-type cisterns was mandatory in the UK to avoid the potential waste of water by millions of leaking toilets with flapper valves but due to EU harmonisation the regulations have changed. These valves can sometimes be more difficult to operate than a "flapper"-based flush valve because the lever requires more torque than a flapper-flush-valve system. This additional torque required at the tank lever is due to the fact that a user must forcefully lift a certain amount of water up into the siphon passageway in order to initiate the siphon action in the tank. Splitting or jamming of the flexible flap covering the perforated disc can also cause the cistern to go out of order.

Dual flush versions of the siphon cistern provide a shorter flush option by allowing air into the siphon to stop the siphonic action before the tank is empty.

The siphon system can also be combined with an air box to allow multiple siphons to be installed in a single trough cistern.

High-pressure or pressure-assisted tanks

Sloan pressure vessel

This system uses water main pressure to pre-pressurize a tank. These may be located inside what otherwise appears to be the more typical ceramic flush tank. A flush cycle begins each time a user flushes the bowl. After a user flushes and the water in the pre-pressurized tank has finished emptying into the bowl, the outlet valve in the plastic tank shuts. Then the high pressure water from the main refills the plastic tank. Inside the tank is an air-filled balloon-like rubber diaphragm. As the higher-pressure mains water enters the tank, the rubber diaphragm is also pressurized and shrinks accordingly.

During flushing, the compressed air inside the diaphragm pushes the water into the bowl at a flow rate which is significantly higher than a tank style gravity-flow toilet. This system requires less water than a gravity-flow toilet- or alternatively can be more effective for a similar amount of water. Pressure-assist toilets are sometimes found in both private (single, multiple, and lodging) bathrooms as well as light commercial installations (such as offices). They seldom clog, but the pressurized tanks require replacement about once every 10 years. They also tend to be noisier - a possible concern for residential settings. Pressure-assist toilets from several companies use 1.4 US gallons (5.3 L) to 1.0 US gallon (3.8 L) per flush.

New toilets that use similar pressure-assist technology along with a bowl and trapway designed to enhance the siphon effect use only 0.8 US gallons (3.0 L) per flush, or 0.5 US gallons (1.9 L) / 0.95 US gallons (3.6 L) for dual flush models. This design is also much quieter than other pressure-assist or flushometer toilets.

Tankless style with high-pressure (flushometer) valve

Main article: Flushometer

In 1906, William Sloan first made his "flushometer" style toilet flush valve, incorporating his patented design, available to the public. The design proved to be very popular and efficient, and remains so to this day. Flushometer toilet flush valves are still often installed in commercial restrooms, and are frequently used for both toilets and urinals. Since they have no tank, they have zero recharge time, and can be used immediately by the next user of the toilet. They can be easily identified by their distinctive chrome pipe-work, and by the absence of a toilet tank or cistern, wherever they are employed.

Some flushometer models require the user to either depress a lever or press a button, which in turn opens a flush valve allowing mains-pressure water to flow directly into the toilet bowl or urinal. Other flushometer models are electronically triggered, using an infrared sensor to initiate the flushing process. Typically, on electronically triggered models, an override button is provided in case the user wishes to manually trigger flushing earlier. Some electronically triggered models also incorporate a true mechanical manual override which can be used in the event of the failure of the electronic system. In retrofit installations, a self-contained battery-powered or hard-wired unit can be added to an existing manual flushometer to flush automatically when a user departs.

Once a flushometer valve has been flushed, and after a preset interval, the flushometer mechanism closes the valve and stops the flow. The flushometer system requires no storage tank, but requires a high volume of water in a very short time. Thus a 3⁄4 inch (22 mm) pipe at minimum, or preferably a 1-inch (29 mm) pipe, must be used, but as the high volume is used only for a short duration, very little water is used for the amount of flushing efficacy delivered. Water main pressures must be above 30 pounds per square inch (2.1 bar). While the higher water pressure employed by a flushometer valve does scour the bowl more efficiently than a gravity-driven system, and while fewer blockages typically occur as a result of this higher water pressure, flushometer systems still require approximately the same amount of water as a gravity system to operate (1.6 gpf).

Bowl design

Four common types of WC pan: washdown (figure 1); washout (figure 2); double-trap siphonic (figure 3); single-trap siphonic with jet (figure 4).

The "bowl" or "pan" of a toilet is the receptacle that receives bodily waste. A toilet bowl is most often made of a ceramic, but can sometimes be made of stainless steel or composite plastics. Toilet bowls are mounted in any one of three basic manners: above-floor mounted (pedestal), wall mounted (cantilever), or in-floor mounted (squat toilet).

Within the bowl, there are three main waterway design systems: the siphoning trapped system (found primarily in North American residential installations, and in North American light commercial installations), the non-siphoning trapped system (found in most other installations both inside and outside of North America), and the valve-closet system (found in many specialty applications, such as in trains, planes, buses, and other such installations around the world). Older style toilets called "washout" toilets are now only found in a few locations.

Siphonic bowls

Single trap siphonic toilet

A simplified cross-section through a siphonic toilet. The arrows show the flow of the flush water through the rim and jet into the bowl and out through the elongated S-shaped siphon.

The siphonic toilet is perhaps the most popular design in North America for residential and light commercial toilet installations. Some other terms for these types of toilets are "siphon jet" and "siphon wash". All siphonic toilets incorporate an "S" shaped waterway.

Standing water in the bowl acts as a barrier to sewer gas coming out of the sewer through the drain, and also as a receptacle for waste. Sewer gas is vented through a separate vent pipe attached to the sewer line. The water in the toilet bowl is connected to the drain by a hollow drain pipe shaped like an extended "S", which curves up behind the bowl and down to the drain. The portion of the channel behind the bowl is arranged as a siphon tube, whose length is greater than the depth of the water in the bowl. The top of the curving tube limits the height of the water in the bowl before it flows down the drain. The waterways in these toilets are designed with slightly smaller diameters than a non-siphonic toilet, so that the waterway will naturally fill up with water each time it is flushed, creating the siphon action.

At the top of the toilet bowl is a rim with many angled drain holes that are fed from the tank, which fill, rinse, and induce swirling in the bowl when it is flushed. Some designs use a large hole in the front of the rim to allow faster filling of the bowl. There may also be a siphon jet hole about 1.0 inch (2.54 cm) diameter in the bottom of the toilet.

If the toilet is flushed from a tank, a large holding cistern is mounted above the toilet, containing approximately 1.2 to 1.6 U.S. gallons (4.5 to 6.1 L) of water in modern designs. This tank is built with a large drain 2.0 to 3.0 inches (5.08 to 7.62 cm) diameter hole at its bottom covered by a flapper valve that allows the water to rapidly leave the holding tank when the flush is activated. Alternatively, water may be supplied directly via a flush valve or "flushometer".

The rapid influx of water into the bowl causes the standing water in the bowl to rise and fill the S-shaped siphon tube mounted in the back of the toilet. This starts the toilet's siphonic action. The siphon action quickly “pulls” nearly all of the water and waste in the bowl and the on-rushing tank water down the drain in about 4–7 seconds —it flushes. When most of the water has drained out of the bowl, the continuous column of water through the siphon is broken when air enters the siphon tube. The toilet then gives its characteristic gurgle as the siphonic action ceases and no more water flows out of the toilet.

A "true siphonic toilet" can be easily identified by the noise it makes. If it can be heard to suck air down the drain at the end of a flush, then it is a true siphonic toilet. If not, then it is either a double trap siphonic or a non-siphonic toilet.

If water is poured slowly into the bowl it simply flows over the rim of the waterway and pours slowly down the drain—thus the toilet does not flush properly.

After flushing, the flapper valve in the water tank closes or the flush valve shuts; water lines and valves connected to the water supply refill the toilet tank and bowl. Then the toilet is again ready for use.

Double trap siphonic toilet

A double-trap siphonic WC. Water enters at (A) sucking air into the aspirator (B) from the siphon leg (E) before passing into the rim (C) and into the pan (D). Water from the first trap in the bowl (F) is sucked through the siphon and out through the second trap (G) to the drain.

The double trap siphonic toilet is a less common type that is exceptionally quiet when flushed. There is a device known as an aspirator which uses the flow of water on a flush to suck air from the cavity between the two traps, reducing the air pressure there to create the siphon which sucks water and waste from the toilet bowl. Towards the end of the flush the aspirator ceases being covered in water, thus allowing air into the cavity between traps to break the siphon without the noise while the final flush water fills the pan.

Non-siphonic bowls

Washdown toilet

Washdown toilets are the most common form of pedestal and cantilever toilets outside North America. The bowl has a large opening at the top which tapers down to a water trap at the base. It is flushed from the top by water discharged through a flushing rim or jets. The force of the water flowing into the bowl washes the waste through the trap and into the drains.

Washdown bowls developed from earlier "hopper" closets, which were simple conical bowls connected to a drain. However, feces is typically excreted towards the back of the toilet, rather than the exact center, and the backs of the hoppers were prone to becoming soiled. The modern washdown bowl has a steeply sloping back and a more gently sloping or curving front, so the water trap is off-center, towards the rear of the toilet. With this "eccentric cone" design, most feces drops into the pool of water at the base of the bowl, rather than onto the surface of the toilet. Early washdown closets had a large water area at the base to minimize soiling, which required a large volume of water to clear them effectively. Modern bowls have a smaller area, which reduces the volume of water needed to flush them.

Washout toilet

A washout toilet which holds fecal matter in a shallow depression until flushed.

Washout, or Flachspüler ("shallow flush"), toilets have a flat platform with a shallow pool of water. They are flushed by a jet of water from the back that drives excreta into the trap below. From there, the water flow removes it into the sewage system. An advantage of the design is that users will not get splashed from below. Washout toilets have a shallow pool of water into which waste is deposited, with a trapped drain just behind this pool. Waste is cleared out from this pool of water by being swept over into the trap (usually either a P-trap or an S-trap) and then beyond into a sewer by water from the flush. Washout pans were amongst the first types of ceramic toilets invented and since the early 1970s are now only found in a decreasing number of localities in continental Europe. A washout toilet is a kind of flush toilet which was once predominantly used in Germany, Austria and France. It was patented in Britain by George Jennings in 1852 and remained the standard toilet type in Britain throughout the 19th century.

Examples of this type of toilet can be found in Australia, Austria, the Czech Republic, Germany, Hungary, the Netherlands, and some regions of Poland, although it is becoming less common.

One disadvantage of this design is that it may require the more intense use of a toilet brush to remove bits of feces that may have left marks on the shelf^{[citation needed]}. Additionally, this design presents the disadvantage of creating a strong lingering odor since the feces are not submerged in water immediately after excretion. Similar designs are found in some early toilets in the US, one particular brand being labeled the "Grand Niagara", as the flushing of the shelf created a waterfall effect into the drain chamber.^{[citation needed]}

Squat toilet

Main article: Squat toilet

Example of a squat toilet in Rome, Italy

In many parts of Asia, people traditionally use the toilet in a squatting position. This applies to defecation and urination by males and females. Therefore, homes and public washrooms have squat toilets, with the toilet bowl installed in the floor. This has the advantages of not needing an additional toilet seat and also being more convenient for cultures where people use water to wash their genitals instead of toilet paper. However, Western-style toilets that are mounted at sitting height and have a plastic seat have become popular as well. Many public washrooms have both squatting and sitting toilets.

In western countries, instructions have been put up in some public toilets on the correct use of a sitting-style toilet. This is to avoid breaking the toilet or seat if someone attempts to squat on the edges.

In India, the "Anglo-Indian" design allows the same toilet to be used in the sitting or the squatting position.

Valve closet

The valve closet has a valve or flap at the exit of the bowl, often with a watertight seal to retain a pool of water in the pan. When the toilet is flushed, the valve is opened and the water in the pan flows rapidly out of the bowl into the drains, carrying the waste with it.

The earliest type of toilet, the valve closet is now rarely used for water-flush toilet systems. More complicated in design than other toilets, this design has lower reliability and is more difficult to maintain or repair. The most common use for valve closets is now in portable closets for caravans, camping, trains, and aircraft, where the flushing fluid is recycled. This design is also used in train carriages for use in areas where the waste is allowed to be simply dumped between the tracks (the flushing of such toilets is generally prohibited when the train is in a station).

Simple valve closets are used on most older style Russian trains, made in Eastern Germany (Ammendorf factory, design dated probably to the 1950s), employing a pan-like shutter valve at the base of the pan and discharging waste directly onto the trackbed below. Usage of this type of toilet is permitted only while the train is moving, and outside of major cities. These designs are being phased out, together with the old trains, and are being replaced with modern vacuum systems.

The British singer Ian Wallace composed and performed the humorous song "Never Do It at the Station", which mentioned the old-fashioned trackbed dumping toilets which were still in use during the mid-20th century in Britain. The song first advised frugal travelers to save money by avoiding pay toilets in train stations, but also reminded polite passengers not to use the onboard "loo" while the train was stopped at a station.

Low-flow and high-efficiency flush toilets

Main articles: Low flush toilet and Dual flush toilet

Since 1994, there is a significant move towards using less water for flushing flush toilets. This has resulted in the emergence of low flush toilet designs and local or national standards on water consumption for flushing. In addition, some people modify their existing high flush toilet to use less water by placing a brick or water bottle into the toilet's water tank. Other modifications are often done on the water system itself (such as by using greywater), or a system that pollutes the water less; hence more efficient use of the water is accomplished.

Urine diversion flush toilets, which were developed in Sweden, save water by using less water, or even no water, for the urine flush compared to about six litres for the feces flush.

US standards for new toilets

Pre-1994 residential and pre-1997 commercial flush toilets in the United States typically used 3.4 US gallons (13 L) of water per flush (gpf or lpf). In 1992, the United States Congress passed the Energy Policy Act of 1992, which mandated that beginning in 1994 common flush toilets use only 1.6 US gallons (6.1 L). In response to the Act, manufacturers produced low-flow toilets, which many consumers did not like because they often required more than one flush to remove solids. People unhappy with the reduced performance of the low-flow toilets resorted to driving across the border to Canada or Mexico, or buying salvaged toilets from older buildings. Manufacturers responded to consumers' complaints by improving the toilets. The improved products are generally identified as high efficiency toilets or HETs. HETs possess an effective flush volume of 1.3 US gallons (4.9 L) or less. HETs may be single-flush or dual-flush. A dual-flush toilet permits its user to choose between two amounts of water, depending on whether they generated solid or liquid waste. Some HETs are pressure-assisted (or power-assisted or pump-assisted or vacuum-assisted).

The performance of a flush-toilet may be rated by a Maximum Performance (MaP) score. The low end of MaP scores is 250 (250 grams of simulated fecal matter). The high end of MaP scores is 1000. A toilet with a MaP score of 1000 should provide trouble-free service. It should remove all waste with a single flush; it should not plug; it should not harbor any odor; it should be easy to keep clean. The United States Environmental Protection Agency uses a MaP score of 350 as the minimum performance threshold for HETs. 1.6 gpf toilets are also sometimes referred as ULF (Ultra Low Flow) toilets.

Methods used to make up for the inadequacies of low flow toilets include using thinner toilet paper, plungers, and adding extra cups of water to the bowl manually.

Maintenance and hygiene

Clogging

If clogging occurs, it is usually the result of an attempt to flush unsuitable items, or too much toilet paper. Flushing of large amounts of hair should also be avoided. However, clogging can occur spontaneously due to limescale fouling of the drain pipe, or by overloading the stool capacity of the toilet. Stool capacity varies among toilet designs and is based on the size of the drainage pipe, the capacity of the water tank, the velocity of a flush, and the method by which the water attempts to vacate the bowl of its contents. The size and consistency of the stool is also a contributing, but hard-to-predict factor.

In some countries, clogging has become more frequent due to regulations that require the use of small-tanked low-flush toilets in attempt to conserve water. Sometimes, three to four flushes periodically during the use of a low-flush toilet may be required to prevent clogging, thus using more water than larger-tanked toilets. Designs which increase the velocity of flushed water or improve the travel path can improve low-flow reliability.

Partial clogging is particularly insidious, as it is usually not discovered immediately, but only later by an unsuspecting user trying to flush a loaded toilet. Overflowing of the water mixed with excrement may then occur, depending on the bowl volume, tank capacity and severity of clogging. For this reason, rooms with flush toilets may be designed as wet rooms, with a second drain on the floor, and a shower head capable of reaching the whole floor area. Common means to remedy clogging include use of a toilet plunger, drain cleaner, or a plumber's snake.

Aerosols

Main article: Toilet plume

Studies have shown aerosol droplets are produced by flushing the toilet, that enter the air of the room. No proven cases of infection have been found, and the risk is unknown. A Fecal-oral route was demonstrated for aerosol droplets that are produced by flushing the toilet. These aerosols are also called "toilet plume" and can spread various germs, viruses, and other pathogens. For this reason, experts recommend users close the toilet seat lid, if available, prior to flushing.

History

See also: History of water supply and sanitation

Ancient flush toilet systems

Dholavira Sophisticated Water Reservoir, evidence for hydraulic sewage systems in the ancient Indus Valley Civilization.

Toilets that used water were used in the Indus Valley Civilization. The cities of Harappa and Mohenjo-daro had a flush toilet in almost every house, attached to a sophisticated sewage system. See also Sanitation of the Indus Valley Civilisation. They also appear in Knossos and Akrotiri of the ancient Minoan civilization from the 2nd millennium BC.

Primitive forms of flush toilets have been found to exist since ancient Neolithic times. The oldest neolithic village in Britain, dating from circa 31st century BC, Skara Brae, Orkney, used a form of hydraulic technology for sanitation. The village's design used a river and connecting drainage system to wash waste away.

Similar toilets were in use throughout the Roman Empire from the 1st through 5th centuries AD. A very well-preserved example are the latrines at Housesteads on Hadrian's Wall in Britain. Such toilets did not flush in the modern sense, but had a continuous stream of running water to wash away waste. With the fall of the Roman Empire, these toilet systems fell into disuse.

Development of the flush toilet

Alexander Cumming's 1775 patent for the S-trap, which laid the foundations for the modern flush toilet.

In 1596, Sir John Harington (1561–1612) published A New Discourse of a Stale Subject, Called the Metamorphosis of Ajax, describing a forerunner to the modern flush toilet installed at his house at Kelston in Somerset. The design had a flush valve to let water out of the tank, and a wash-down design to empty the bowl. He installed one for his godmother Queen Elizabeth I at Richmond Palace.

With the onset of the Industrial Revolution and related advances in technology, the flush toilet began to emerge into its modern form. A crucial advance in plumbing was the S-trap, invented by the Scottish mechanic Alexander Cumming in 1775, and still in use today. This device uses the standing water to seal the outlet of the bowl, preventing the escape of foul air from the sewer. His design had a sliding valve in the bowl outlet above the trap. Two years later, Samuel Prosser applied for a British patent for a "plunger closet".

Joseph Bramah's improved version was the first practical flush toilet.

Prolific inventor Joseph Bramah began his professional career installing water closets (toilets) that were based on Alexander Cumming's patented design of 1775. He found that the current model being installed in London houses had a tendency to freeze in cold weather. In collaboration with a Mr Allen, he improved the design by replacing the usual slide valve with a hinged flap that sealed the bottom of the bowl.

He also developed a float valve system for the flush tank. Obtaining the patent for it in 1778, he began making toilets at a workshop in Denmark Street, St Giles. The design was arguably the first practical flush toilet, and production continued well into the 19th century, used mainly on boats.

Industrial production

Thomas William Twyford was one of the leading marketers of flush toilets in their first boom of popularity after the Great Exhibition of 1851.

It was only in the mid-19th century, with growing levels of urbanisation and industrial prosperity, that the flush toilet became a widely used and marketed invention. This period coincided with the dramatic growth in the sewage system, especially in London, which made the flush toilet particularly attractive for health and sanitation reasons.

George Jennings established a business manufacturing water closets, salt-glaze drainage, sanitary pipes and sanitaryware at Parkstone Pottery in the 1840s, where he popularized the flush toilet to middle class. At The Great Exhibition at Hyde Park held from 1 May to 15 October 1851, George Jennings installed his Monkey Closets in the Retiring Rooms of The Crystal Palace. These were the first public pay toilets (free ones did not appear until later), and they caused great excitement. During the exhibition, 827,280 visitors paid one penny to use them; for the penny they got a clean seat, a towel, a comb, and a shoe shine. "To spend a penny" became a euphemism (now archaic) for going to the toilet.

George Jennings trademark on his manufactures.

When the exhibition finished and moved to Sydenham, the toilets were to be closed down. However, Jennings persuaded the organisers to keep them open, and the toilet went on to earn over £1000 a year. He opened the first underground convenience at the Royal Exchange in 1854. He received a patent in 1852 for an improved construction of water-closet, in which the pan and trap were constructed in the same piece, and so formed that there was always a small quantity of water retained in the pan itself, in addition to that in the trap which forms the water-joint. He also improved the construction of valves, drain traps, forcing pumps and pump-barrels. By the end of the 1850s building codes suggested that most new middle-class homes in British cities were equipped with a water closet.

Another pioneering manufacturer was Thomas William Twyford, who invented the single piece, ceramic flush toilet. The 1870s proved to be a defining period for the sanitary industry and the water closet; the debate between the simple water closet trap basin made entirely of earthenware and the very elaborate, complicated and expensive mechanical water closet would fall under public scrutiny and expert opinion. In 1875, the "wash-out" trap water closet was first sold and was found as the public's preference for basin type water closets. By 1879, Twyford had devised his own type of the "wash out" trap water closet, he titled it the "National", and became the most popular wash-out water closet.

Flush toilets were widely available from the mid to late 19th century. Although Thomas Crapper did not invent the flush toilet, he was a leading manufacturer.

By the 1880s, the free-standing water closet was sold and quickly gained popularity; the free-standing water closet was able to be cleaned more easily and was therefore a more hygienic water closet. Twyford's "Unitas" model was free standing and made completely of earthenware. Throughout the 1880s he submitted further patents for improvements to the flushing rim and the outlet. Finally in 1888, he applied for a patent protection for his "after flush" chamber; the device allowed for the basin to be refilled by a lower quantity of clean water in reserve after the water closet was flushed. The modern pedestal "flush-down" toilet was demonstrated by Frederick Humpherson of the Beaufort Works, Chelsea, England in 1885.

The leading companies of the period issued catalogues, established showrooms in department stores and marketed their products around the world. Twyford had showrooms for water closets in Berlin, Germany; Sydney, Australia; and Cape Town, South Africa. The Public Health Act 1875 set down stringent guidelines relating to sewers, drains, water supply and toilets and lent tacit government endorsement to the prominent water closet manufacturers of the day.

Contrary to popular legend, Sir Thomas Crapper did not invent the flush toilet. He was, however, in the forefront of the industry in the late 19th century, and held nine patents, three of them for water closet improvements such as the floating ballcock. His flush toilets were designed by inventor Albert Giblin, who received a British patent for the "Silent Valveless Water Waste Preventer", a siphon discharge system. Crapper popularized the siphon system for emptying the tank, replacing the earlier floating valve system which was prone to leaks.

Spread and further developments

Although flush toilets first appeared in Britain, they soon spread to the Continent. The first such examples may have been the three "waterclosets" installed in the new town house of banker Nicolay August Andresen on 6 Kirkegaten in Christiania, insured in January 1859. The toilets were probably imported from Britain, as they were referred to by the English term "waterclosets" in the insurance ledger. Another early watercloset on the European continent, dating from 1860, was imported from Britain to be installed in the rooms of Queen Victoria in Ehrenburg Palace (Coburg, Germany); she was the only one who was allowed to use it.

In America, the chain-pull indoor toilet was introduced in the homes of the wealthy and in hotels, soon after its invention in England in the 1880s. Flush toilets were introduced in the 1890s. William Elvis Sloan invented the Flushometer in 1906, which used pressurized water directly from the supply line for faster recycle time between flushes. The Flushometer is still in use today in public restrooms worldwide. The vortex-flushing toilet bowl, which creates a self-cleansing effect, was invented by Thomas MacAvity Stewart of Saint John, New Brunswick in 1907. Philip Haas of Dayton, Ohio, made some significant developments, including the flush rim toilet with multiple jets of water from a ring and the water closet flushing and recycling mechanism similar to those in use today.

The company Caroma in Australia developed the Duoset cistern with two buttons and two flush volumes as a water-saving measure in 1980. Modern versions of the Duoset are now available worldwide, and save the average household 67% of their normal water usage.

Manufacture

Toilet with an elevated cistern of water and a chain attached to the tank to release water and flush the waste away

A toilet's body is typically made from vitreous china, which starts out as an aqueous suspension of various minerals called a slip. It takes about 20 kilograms (44 lb) of slip to make a toilet.

This slip is poured into the space between plaster of Paris molds. The toilet bowl, rim, tank and tank lid require separate molds. The molds are assembled and set up for filling and the slip-filled molds sit for about an hour after filling. This allows the plaster molds to absorb moisture from the slip, which makes it semisolid next to the mold surfaces but lets it remain liquid further from the surface of the molds. Then, the workers remove plugs to allow any excess liquid slip to drain from the cavities of the mold (this excess slip is recycled for later use). The drained-out slip leaves hollow voids inside the fixture, using less material to keep it both lighter and easier to fire in a kiln. This molding process allows the formation of intricate internal waste lines in the fixture; the drain's hollow cavities are poured out as slip.

At this point, the toilet parts without their molds look like and are about as strong as soft clay. After about one hour the top core mold (interior of toilet) is removed. The rim mold bottom (which includes a place to mount the holding tank) is removed, and it then has appropriate slanted holes for the rinsing jets cut, and the mounting holes for tank and seat are punched into the rim piece. Valve holes for rapid water entry into the toilet are cut into the rim pieces. The exposed top of the bowl piece is then covered with a thick slip and the still-uncured rim is attached on top of the bowl so that the bowl and hollow rim are now a single piece. The bowl plus rim is then inverted, and the toilet bowl is set upside down on the top rim mold to hold the pieces together as they dry. Later, all the rest of the mold pieces are removed. As the clay body dries further it hardens more and continues to shrink. After a few hours, the casting is self-supporting, and is called greenware.

After the molds are removed, workers use hand tools and sponges to smooth the edges and surface of the greenware, and to remove the mold joints or roughness: this process is called "fettling". For large scale production pieces, these steps may be automated. The parts are then left outside or put in a warm room to dry, before going through a dryer at about 93 °C (199 °F), for about 20–36 hours.

After the surfaces are smoothed, the bowls and tanks are sprayed with glaze of various kinds to get different colors. This glaze is designed to shrink and contract at the same rate as the greenware while undergoing firing. After being sprayed with glaze, the toilet bowls, tanks, and lids are placed in stacks on a conveyor belt or "car" that slowly goes through a large kiln to be fired. The belt slowly moves the glaze-covered greenware into a tunnel kiln, which has different temperature zones inside it starting at about 200 °C (392 °F) at the front, increasing towards the middle to over 1,200 °C (2,190 °F) degrees and exiting around out 90 °C (194 °F). During the firing in the kiln, the greenware and glaze are vitrified as one solid finished unit. Transiting the kiln takes glaze-covered greenware around 23–40 hours.

After the pieces are removed from the kiln and fully cooled, they are inspected for cracks or other defects. Then, the flushing mechanism may be installed on a one-piece toilet. On a two-piece toilet with a separate tank, the flushing mechanism may only be placed into the tank, with final assembly at installation.

A two-piece attaching seat and toilet bowl lid are typically mounted over the bowl to allow covering the toilet when it is not in use and to provide seating comfort. The seat may be installed at the factory, or the parts may be sold separately and assembled by a plumbing distributor or the installer.

Water usage

The bowl drain is visible at the rear of the bowl, connected to the waste pipe.

The amount of water used by conventional flush toilets usually make up a significant portion of personal daily water usage: for example, it could be as much as 50 liters (13 U.S. gal) per person per day if a person flushes his or her toilet five times per day with 10 liters per flush.

Modern low-flush toilet designs allow the use of much less water per flush —4.5 to 6 liters (1.2 to 1.6 U.S. gal) per flush.

Some users do not flush their toilets after urination, in order to save water.

Dual flush toilets allow the user to select between a flush for urine or feces, saving a significant amount of water over conventional units. The flush handle on some of these toilets is pushed up for one kind of flush and down for the other. In other designs, a segmented flush pushbutton is used; pressing the smaller section releases less water.

Flushing with non-potable water sources

Raw water flushing, including seawater flushing, is a method of water conservation, where raw water, such as seawater, is used for flush toilets. Such systems are used in places such as the majority of cities and towns in Hong Kong (see water supply and sanitation in Hong Kong), Gibraltar, and Avalon, California, United States. Heads (on ships) are typically flushed with seawater.

Flush toilets may, if plumbed for it, use greywater (water previously used for washing dishes, laundry and bathing) for flushing rather than potable water (drinking water).

Etymology

Water closet

The term "water closet" ("WC") was an early term for an interior or exterior room with a flushing toilet in contrast with an earth closet usually outdoors and requiring periodic emptying as "night soil". Originally, the term "wash-down closet" was used. The term "water closet" was coined in England around 1870. It did not reach the United States until the 1880s. Around this time, only luxury hotels and wealthy people had indoor private bathrooms. By 1890 in the US, there was increased public awareness of the theory of disease and of carelessly disposed human waste being contaminated and infectious.

Originally, the term "bath-room" referred only to the room where the bathtub was located (usually a separate room not housing a toilet), but this connotation has changed in common North American usage. In the UK, the terms "bathroom" and "toilet" are used to indicate distinct functions, even though bathrooms in modern homes often include toilets. The term "water closet" was probably adopted because in the late 19th century, with the advent of indoor plumbing, a toilet displaced an early clothes closet, closets being renovated to easily accommodate the spatial needs of a commode. Early indoor toilets had in fact been known as garderobes because they actually were used to store clothes, as the smell of ammonia was found to deter fleas and moths.

The term "water closet" now often refers to a room that has both a toilet and other plumbing fixtures such as a sink or a bathtub. Plumbing manufacturers often use the term "water closet" to differentiate toilets from urinals. American plumbing codes refer to a toilet as a "Water Closet" or a "WC". Many European languages refer to a toilet as a "water" or "WC". The Royal Spanish Academy Dictionary accepts "váter" as a name for a toilet or bathroom, which is derived from the British term "water closet". In French, the expression aller aux waters ("to go to the waters") derives from "water closet". "w.-c." is used in the French language, pronounced /ve.se/. Likewise the Romanian word "veceu", pronounced /vetʃeu/, derives from a shortened version of the abbreviation. In German, the expression "Klo" (first syllable of "Kloset") is used alongside "WC"

In many Asian countries and China in particular, "WC" is used as a universal name for the toilet; many Chinese people will make a hand sign with the forefinger and thumb held in the shape of a "C" while the remaining 3 fingers of the same hand are extended to represent a "W", thus indicating where they are going or perhaps to explain where someone has gone.

Society and culture

Swirl direction myth

It is a commonly held misconception that when flushed, the water in a toilet bowl swirls one way if the toilet is north of the equator and the other way if south of the equator, due to the Coriolis effect – usually, counter clockwise in the northern hemisphere, and clockwise in the southern hemisphere. In reality, the direction that the water takes is much more determined by the direction that the bowl's rim jets are pointed, and it can be made to flush in either direction in either hemisphere by simply redirecting the rim jets during manufacture. On the scale of bathtubs and toilets, the Coriolis effect is too weak to be observed except under carefully controlled laboratory conditions.

See also

• Dry toilet
• Public toilet
• Sanitation
• Toilets in Japan
• Thomas Maddock, started the American indoor toilet industry