Hard disk drive

Hard disk drive

An IBM hard disk drive with the metal cover removed. The platters are highly reflective.
Date invented	September 13 1956
Invented by	Reynold Johnson
Connects to	Controller (typically on motherboard) via one of: PATA (IDE) interface SCSI interface SATA interface SAS interface Controller (typically found on servers) via one of: FCAL interface SCSI interface Controller (formerly common, now disused) via one of: ESDI interface ST-506 interface
Market Segments	Desktop Mobile Enterprise Consumer Other/Miscellaneous

A hard disk drive (HDD), commonly referred to as a hard drive or hard disk, is a non-volatile storage device which stores digitally encoded data on rapidly rotating platters with magnetic surfaces. Strictly speaking, "drive" refers to a device distinct from its medium, such as a tape drive and its tape, or a floppy disk drive and its floppy disk. Early HDDs had removable media; however, an HDD today is typically a sealed unit with fixed media.

HDDs were originally developed for use with computers. In the 21st century, applications for HDDs have expanded beyond computers to include digital video recorders, digital audio players, personal digital assistants, digital cameras, and video game consoles. In 2005 the first mobile phones to include HDDs were introduced by Samsung and Nokia. The need for large-scale, reliable storage, independent of a particular device, led to the introduction of configurations such as RAID arrays, network attached storage (NAS) systems and storage area network (SAN) systems that provide efficient and reliable access to large volumes of data.

Technology

File:Hard drive.svg

A hard disk drive stores information on one or more rigid, flat, disks. The disks are mounted on a spindle, with spaces in between, and a motor on the bottom end of the spindle. To read and write to the surface of the disks, the drive uses a small electro-magnet assembly, referred to as a head, located on the end of an actuator arm. There is one head for each platter surface on the spindle. The disks are spun at a very high speed to allow the head to move quickly over the surface of the disk. Towards the other end of the actuator arm is a pivot point, and at the end is a voice coil, which moves the head. Above and below each voice coil is a rare earth magnet. This allows the head to move towards the center of the disk or towards the outside, in a radial pattern.

A cross section of the magnetic surface in action. In this case the binary data encoded using frequency modulation.

The disk controller uses a digital-to-analog converter to control the flow of electricity through the voice coil(s) located on the of the actuator arm. The voice coil acts as an electromagnet; it produces a magnetic field that interacts with magnetic fields of the magnet located above and below the voice coil, which causes the voice coil to move the actuator arm, and in turn the head located on the opposite end of the actuator arm. So as the voice coil is pushed towards one end, the assembly moves the head towards the center, and when the voice coil is pushed towards the other end, the heads move towards the outside edge of the disk, or the heads are parked. The digital-to-analog converter allows the disk controller to move the head in tiny steps in either direction.

The disks are made of a non-magnetic material, usually aluminum or glass, and are coated with a very thin layer of magnetic material. Older disks used iron(III) oxide as the magnetic material, but current disks use a cobalt-based alloy.

The inside of a hard disk drive with the disk(s) and spindle motor hub removed. To the left of center is the actuator arm. A read-write head is at the end of the arm. The head slider is located just behind the head, on the underside of the arm. The orange wires on the side of the arm, connect the heads to the drives controller. The pivot point is the round bolt seen just before the metal plate. The semi-circular metal plate, top left corner, is one of the permanent magnets that are used in moving the arm. The voice coil is located underneath, with a second magnet below.The air filter is within the plastic housing in the bottom left.

The magnetic surface of each platter is divided into many small sub-micrometre-sized magnetic regions, each of which is used to encode a single binary unit of information. In today's HDDs each of these magnetic regions is composed of a few hundred magnetic grains. Each magnetic region forms a magnetic dipole which generates a highly localized magnetic field nearby. The write head magnetizes a magnetic region by generating a strong local magnetic field nearby. Early HDDs used the same inductor that was used to read the data as an electromagnet to create this field. Later versions of inductive heads included metal in Gap (MIG) heads and thin film heads. In today's heads, the read and write elements are separate but in close proximity on the head portion of an actuator arm. The read element is typically magneto-resistive while the write element is typically thin-film inductive.

Hard disk drives are sealed to prevent dust and other sources of contamination from interfering with the operation of the hard disks heads. The hard drives are not air tight, but rather utilize an extremely fine air filter, to allow for air inside the hard drive enclosure. The spinning of the disks causes the air to circulate forcing any particulates to become trapped on the filter. The spinning of the disks, also allows the hard disk heads to float above the surface of the disk surface using the same air currents. See Bernoulli's principle.

Using rigid disks and sealing the unit allows much tighter tolerances than in a floppy disk drive. Consequently, hard disk drives can store much more data than floppy disk drives and access and transmit it faster. In 2007, a typical enterprise, i.e. workstation HDD might store between 160 GB and 1 TB of data (as of local US market by July 2007), rotate at 7,200 or 10,000 revolutions per minute (RPM), and have a sequential media transfer rate of over 80 MB/s. The fastest enterprise HDDs spin at 15,000 RPM, and can achieve sequential media transfer speeds up to and beyond 110 MB/s. Mobile, i.e., Laptop HDDs, which are physically smaller than their desktop and enterprise counterparts, tend to be slower and have less capacity. In the 1990s, most spun at 4,200 RPM. In 2007, a typical mobile HDD spins at 5,400 RPM, with 7,200 RPM models available for a slight price premium.

Hard drives are precise devices, moving at very high speed, and a number of analogies have been made to try to describe this. One analogy, proposed by Scott Mueller, says:

...to such a scale, the heads in this typical hard disk would be about [...] equal to the Sears Tower if it were tipped over sideways. These skyscaper sized heads would float on a cushion of air that to scale would only be 5mm thick (about 0.2") while [...] circling the Earth once every 5 seconds!

— Scott Mueller, Upgrading and Repairing PCs, 17th edition

Capacity and access speed

PC hard disk drive capacity (in GB). The plot is logarithmic, so the fit line corresponds to exponential growth.

The exponential increases in disk space and data access speeds of HDDs have enabled the commercial viability of consumer products that require large storage capacities, such as the TiVo personal video recorder and digital music players. In addition, the availability of vast amounts of cheap storage has made viable a variety of web-based systems with extraordinary capacity requirements, such as the search and email systems offered by companies like Google.

The main way to decrease access time is to increase rotational speed, while the main way to increase throughput and storage capacity is to increase areal density. A vice president of Seagate Technology projects a future growth in disk density of 40% per year. Access times have not kept up with throughput increases, which themselves have not kept up with growth in storage capacity.

As of 2006, disk drives include perpendicular recording technology, in the attempt to enhance recording density and throughput.

The first 3.5" HDD marketed as able to store 1 TB is the Hitachi Deskstar 7K1000. The drive contains five platters at approximately 200 GB each, providing 935.5 GiB of usable space. Hitachi has since been joined by Samsung and Seagate in the 1 TB drive market.

Standard Name	Width	Largest capacity to date (2007)	Platters (Max)
5.25" FH	146 mm	47 GB	14
5.25" HH	146 mm	19.3 GB	4
3.5"	102 mm	1.2 TB	5
2.5"	69.9 mm	320 GB	3
1.8" (PCMCIA)	54 mm	160 GB
1.8" (ATA-7 LIF)	53.8 mm

Capacity measurements

The capacity of an HDD can be calculated by multiplying the number of cylinders by the number of heads by the number of sectors by the number of bytes/sector (most commonly 512). On ATA drives bigger than 8 gigabytes, the values are set to 16383 cylinder, 16 heads, 63 sectors for compatibility with older operating systems. It should be noted that the values for cylinder, head & sector reported by a modern drive are not the actual physical parameters since, amongst other things, with zone bit recording the number of sectors varies by zone.

Hard disk drive manufacturers specify disk capacity using the SI prefixes mega, giga, and tera and their abbreviations M, G and T, respectively. Byte is typically abbreviated B.

Operating systems frequently report capacity using the same abbreviations but with a binary interpretation. For instance, the prefix mega can also mean 2²⁰ (1,048,576), which is approximately 1,000,000. Similar usage has been applied to prefixes of greater magnitude. This results in a discrepancy between the disk manufacturer's stated capacity and what the system reports. The difference becomes much more noticeable in the multi-gigabyte range. For example, Microsoft Windows reports disk capacity both in decimal to 12 or more significant digits and with binary prefixes to 3 significant digits. Thus a disk specified by a disk manufacturer as a 30 GB disk might have its capacity reported by Windows 2000 both as "30,065,098,568 bytes" and "28.0 GB" The disk manufacturer used the SI definition of "giga", 10⁹ to arrive at 30 GB; however, because the utilities provided by Windows define a gigabyte as 1,073,741,824 bytes (2³⁰ bytes), the operating system reports capacity of the disk drive as 28.0 GB.

History

Main article: History of hard disk drives

IBM 62PC "Piccolo" HDD, circa 1979 - an early 8" disk

For many years, HDDs were large, cumbersome devices, more suited to use in the protected environment of a data center or large office than in a harsh industrial environment (due to their delicacy), or small office or home (due to their size and power consumption). Before the early 1980s, most HDDs had 8-inch (20 cm) or 14-inch (35 cm) platters, required an equipment rack or a large amount of floor space (especially the large removable-media disks, which were often referred to as "washing machines"), and in many cases needed high-current or even three-phase power hookups due to the large motors they used. Because of this, HDDs were not commonly used with microcomputers until after 1980, when Seagate Technology introduced the ST-506, the first 5.25-inch HDD, with a capacity of 5 megabytes. In fact, in its factory configuration, the original IBM PC (IBM 5150) was not equipped with a hard disk drive.

Most microcomputer HDDs in the early 1980s were not sold under their manufacturer's names, but by OEMs as part of larger peripherals (such as the Corvus Disk System and the Apple ProFile). The IBM PC/XT had an internal HDD, however, and this started a trend toward buying "bare" disks (often by mail order) and installing them directly into a system. Hard disk drive makers started marketing to end users as well as OEMs, and by the mid-1990s, HDDs had become available on retail store shelves.

While internal disks became the system of choice on PCs, external HDDs remained popular for much longer on the Apple Macintosh and other platforms. The first Apple Macintosh built between 1984 and 1986 had a closed architecture that did not support an external or internal hard drive. In 1986, Apple added a SCSI port on the back, making external expansion easy. External SCSI drives were also popular with older microcomputers such as the Apple II series, and were also used extensively in servers, a usage which is still popular today. The appearance in the late 1990s of high-speed external interfaces such as USB and FireWire has made external disk systems popular among PC users once again, especially for laptop users, users that install Linux in the additional external unit and users who move large amounts of data between two or more areas. Most HDD makers now make their disks available in external cases.

Hard disk drive characteristics

5.25" MFM 110 MB HDD (2.5" ATA 6495 MB HDD, US & UK pennies for comparison)

Capacity of a hard disk drive is usually quoted in gigabytes. Older HDDs quoted their smaller capacities in megabytes.

The data transfer rate at the inner zone ranges from 44.2 MB/s to 74.5 MB/s, while the transfer rate at the outer zone ranges from 74.0 MB/s to 111.4 MB/s. An HDD's random access time ranges from 5 ms to 15 ms.

The physical size of a hard disk drive is quoted in inches. The majority of HDDs used in desktops today are 3.5" wide, while those used in laptops are 2.5" wide. As of early 2007, manufacturers have started selling SATA and SAS 2.5 inch drives for use in servers and desktops.

An increasingly common form factor is the 1.8" ATA-7 LIF form factor used inside digital audio players and subnotebooks, which provide up to 160GB storage capacity at low power consumption and are highly shock-resistant. A previous 1.8" HDD standard exists, for 2–5GB sized disks that fit directly into a PC card expansion slot. From these, the smaller 1" form factor was evolved, which is designed to fit the dimensions of CF Type II, which is also usually used as storage for portable devices including digital cameras. 1" was a de facto form factor led by IBM's Microdrive, but is now generically called 1" due to other manufacturers producing similar products. There is also a 0.85 inch form factor produced by Toshiba for use in mobile phones and similar applications, including SD/MMC slot compatible HDDs optimized for video storage on 4G handsets.

The size designations are more nomenclature than descriptive. The names refer to the width of the disk inserted into the drive rather than the actual width of the entire drive. A 5.25" drive has an actual width of 5.75", a 3.5" drive 4", a 2.5" drive 2.75". A 1.8" drive can have different widths, depending on its form factor. A PCMCIA drive has a width of 54 mm, while an ATA-7 LIF form factor drive has a width of 53.85 mm.

A hard disk is defined to be at "full height" if its height is 3.25". It is "half height" at a height of 1.625". A "slim height" or "low profile" HDD has a height of 1". "Ultra low profile" drives can have heights of 0.75", 0.67", 0.49" or 0.37".

Integrity

An IBM HDD head resting on a disk platter. Since the drive is not in operation, the head is simply pressed against the disk by the suspension.

The HDD's spindle system relies on air pressure inside the enclosure to support the heads at their proper flying height while the disk rotates. An HDD requires a certain range of air pressures in order to operate properly. The connection to the external environment and pressure occurs through a small hole in the enclosure (about 0.5 mm in diameter), usually with a carbon filter on the inside (the breather filter, see below). If the air pressure is too low, then there is not enough lift for the flying head, so the head gets too close to the disk, and there is a risk of head crashes and data loss. Specially manufactured sealed and pressurized disks are needed for reliable high-altitude operation, above about 10,000 feet (3,000 m). This does not apply to pressurized enclosures, like an airplane pressurized cabin. Modern disks include temperature sensors and adjust their operation to the operating environment. Breather holes can be seen on all disks — they usually have a sticker next to them, warning the user not to cover the holes. The air inside the operating disk is constantly moving too, being swept in motion by friction with the spinning platters. This air passes through an internal recirculation (or "recirc") filter to remove any leftover contaminants from manufacture, any particles or chemicals that may have somehow entered the enclosure, and any particles or outgassing generated internally in normal operation. Very high humidity for extended periods can corrode the heads and platters. If the disk uses "Contact Start/Stop" (CSS) technology to park its heads on the platters when not operating, increased humidity can also lead to increased stiction (the tendency for the heads to stick to the platter surface). This can cause physical damage to the platter and spindle motor and cause head crash.

Close-up of a hard disk head resting on a disk platter, and its suspension. A reflection of the head and suspension are visible beneath on the mirror-like disk.

Due to the extremely close spacing between the heads and the disk surface, any contamination of the read-write heads or platters can lead to a head crash — a failure of the disk in which the head scrapes across the platter surface, often grinding away the thin magnetic film. For giant magnetoresistive (GMR) heads in particular, a minor head crash from contamination (that does not remove the magnetic surface of the disk) still results in the head temporarily overheating, due to friction with the disk surface, and can render the data unreadable for a short period until the head temperature stabilizes (so called "thermal asperity," a problem which can partially be dealt with by proper electronic filtering of the read signal). Head crashes can be caused by electronic failure, a sudden power failure, physical shock, wear and tear, corrosion, or poorly manufactured platters and heads. In most desktop and server disks, when powering down, the heads are moved to a landing zone, an area of the platter usually near its inner diameter (ID), where no data are stored. This area is called the CSS (Contact Start/Stop) zone. However, especially in old models, sudden power interruptions or a power supply failure can sometimes result in the device shutting down with the heads in the data zone, which increases the risk of data loss. In fact, it used to be procedure to "park" the hard disk before shutting down your computer. Newer disks are designed such that either a spring (at first) or (more recently) rotational inertia in the platters is used to safely park the heads in the case of unexpected power loss.

The hard disk's electronics control the movement of the actuator and the rotation of the disk, and perform reads and writes on demand from the disk controller. Modern disk firmware is capable of scheduling reads and writes efficiently on the platter surfaces and remapping sectors of the media which have failed. Also, most major hard disk and motherboard vendors now support self-monitoring, analysis, and reporting technology (S.M.A.R.T.), which attempt to alert users to impending failures.

However, not all failures are predictable. Normal use eventually can lead to a breakdown in the inherently fragile device, which makes it essential for the user to periodically back up the data onto a separate storage device. Failure to do so can lead to the loss of data. While it may be possible to recover lost information, it is normally an extremely costly procedure, and it is not possible to guarantee success in the attempt. A 2007 study published by Google suggested very little correlation between failure rates and either high temperature or activity level. While several S.M.A.R.T. parameters have an impact on failure probability, a large fraction of failed drives do not produce predictive S.M.A.R.T. parameters. S.M.A.R.T. parameters alone may not be useful for predicting individual drive failures.

Landing zones

Microphotograph of a hard disk head. The size of the front face (which is the "trailing face" of the slider) is about 0.3 mm × 1.0 mm. The (not visible) bottom face of the slider is about 1.0 mm × 1.25 mm (so called "nano" size) and faces the platter. One functional part of the head is the round, orange structure in the middle - the lithographically defined copper coil of the write transducer. Also note the electric connections by wires bonded to gold-plated pads.

Spring tension from the head mounting constantly pushes the heads towards the platter. While the disk is spinning, the heads are supported by an air bearing and experience no physical contact or wear. In CSS drives the sliders carrying the head sensors (often also just called heads) are designed to reliably survive a number of landings and takeoffs from the media surface, though wear and tear on these microscopic components eventually takes its toll. The heads typically land in a "landing zone" that does not contain user data. Most manufacturers design the sliders to survive 50,000 contact cycles before the chance of damage on startup rises above 50%. However, the decay rate is not linear—when a disk is younger and has fewer start-stop cycles, it has a better chance of surviving the next startup than an older, higher-mileage disk (as the head literally drags along the disk's surface until the air bearing is established). For example, the Seagate Barracuda 7200.10 series of desktop hard disks are rated to 50,000 start-stop cycles. This means that no failures attributed to the head-platter interface were seen before at least 50,000 start-stop cycles during testing.

Around 1995 IBM pioneered a technology where a landing zone on the disk is made by a precision laser process (Laser Zone Texture = LZT) producing an array of smooth nanometer-scale "bumps" in a landing zone, thus vastly improving stiction and wear performance. This technology is still largely in use today (2006). In most mobile applications, the heads are lifted off the platters onto plastic "ramps" near the outer disk edge, thus eliminating the risks of wear and stiction altogether and greatly improving non-operating shock performance. All HDDs use one of these two technologies. Each has a list of advantages and drawbacks in terms of loss of storage space, relative difficulty of mechanical tolerance control, cost of implementation, etc.

IBM created a technology for their ThinkPad line of laptop computers called the Active Protection System. When a sudden, sharp movement is detected by the built-in motion sensor in the Thinkpad, internal hard disk heads automatically unload themselves into the parking zone to reduce the risk of any potential data loss or scratches made. Apple later also utilized this technology in their PowerBook, iBook, MacBook Pro, and MacBook line, known as the Sudden Motion Sensor. Toshiba has released similar technology in their laptops.

Access and interfaces

Hard disk drives are accessed over one of a number of bus types, including ATA (IDE, EIDE), Serial ATA (SATA), SCSI, SAS, and Fibre Channel. Bridge circuitry is sometimes used to connect hard disk drives to busses that they cannot communicate with natively, such as IEEE 1394 and USB.

Back in the days of the ST-506 interface, the data encoding scheme was also important. The first ST-506 disks used Modified Frequency Modulation (MFM) encoding, and transferred data at a rate of 5 megabits per second. Later on, controllers using 2,7 RLL (or just "RLL") encoding increased the transfer rate by fifty percent, to 7.5 megabits per second; it also increased disk capacity by fifty percent.

Many ST-506 interface disk drives were only specified by the manufacturer to run at the lower MFM data rate, while other models (usually more expensive versions of the same basic disk drive) were specified to run at the higher RLL data rate. In some cases, a disk drive had sufficient margin to allow the MFM specified model to run at the faster RLL data rate; however, this was often unreliable and was not recommended. (An RLL-certified disk drive could run on a MFM controller, but with 1/3 less data capacity and speed.)

Enhanced Small Disk Interface (ESDI) also supported multiple data rates (ESDI disks always used 2,7 RLL, but at 10, 15 or 20 megabits per second), but this was usually negotiated automatically by the disk drive and controller; most of the time, however, 15 or 20 megabit ESDI disk drives weren't downward compatible (i.e. a 15 or 20 megabit disk drive wouldn't run on a 10 megabit controller). ESDI disk drives typically also had jumpers to set the number of sectors per track and (in some cases) sector size.

SCSI originally had just one speed, 5 MHz (for a maximum data rate of 5 megabytes per second), but later this was increased dramatically. The SCSI bus speed had no bearing on the disk's internal speed because of buffering between the SCSI bus and the disk drive's internal data bus; however, many early disk drives had very small buffers, and thus had to be reformatted to a different interleave (just like ST-506 disks) when used on slow computers, such as early IBM PC compatibles and early Apple Macintoshes.

ATA disks have typically had no problems with interleave or data rate, due to their controller design, but many early models were incompatible with each other and couldn't run in a master/slave setup (two disks on the same cable). This was mostly remedied by the mid-1990s, when ATA's specification was standardised and the details began to be cleaned up, but still causes problems occasionally (especially with CD-ROM and DVD-ROM disks, and when mixing Ultra DMA and non-UDMA devices).

Serial ATA does away with master/slave setups entirely, placing each disk on its own channel (with its own set of I/O ports) instead.

FireWire/IEEE 1394 and USB(1.0/2.0) HDDs are external units containing generally ATA or SCSI disks with ports on the back allowing very simple and effective expansion and mobility. Most FireWire/IEEE 1394 models are able to daisy-chain in order to continue adding peripherals without requiring additional ports on the computer itself.

Disk families used in personal computers

Notable disk families include:

• Bit Serial Interfaces — These families connected to a hard disk drive controller with three cables, one for data, one for control and one for power. The HDD controller provided significant functions such as serial to parallel conversion, data separation and track formatting, and required matching to the drive in order to assure reliability.
  • ST506 used MFM (Modified Frequency Modulation) for the data encoding method.
  • ST412 was available in either MFM or RLL (Run Length Limited) variants.
  • ESDI (Enhanced Small Disk Interface) was an interface developed by Maxtor to allow faster communication between the PC and the disk than MFM or RLL.
• Word Serial Interfaces — These families connect to a host bus adapter (today typically integrated into the "South Bridge") with two cables, one for data/control and one for power. The earliest versions of these interfaces typically had a 16 bit parallel data transfer to/from the drive and there are 8 and 32 bit variants. Modern versions have serial data transfer. The word nature of data transfer makes the design of a host bus adapter significantly simpler than that of the precursor HDD controller.
  • Integrated Drive Electronics (IDE) was later renamed to ATA, and then later, PATA ("parallel ATA", to distinguish it from the new serial ATA interface, SATA). The name comes from the way early families had the HDD controller external to the disk. Moving the HDD controller from the interface card to the disk helped to standardize interfaces, including reducing the cost and complexity. The 40 pin IDE/ATA connection of PATA transfers 16 bits of data at a time on the data cable. The data cable was originally 40 conductor, but later higher speed requirements for data transfer to and from the hard drive led to an "ultra DMA" mode, known as UDMA, which required an 80 conductor variant of the same cable; the other conductors provided the grounding necessary for enhanced high-speed signal quality. The interface for 80 pin only has 39 pins, the missing pin acting as a key to prevent incorrect insertion of the connector to an incompatible socket, a common cause of disk and controller damage.
  • EIDE was an unofficial update (by Western Digital) to the original IDE standard, with the key improvement being the use of DMA ("Direct memory access") to transfer data between the disk and the computer without the involvement of the CPU, an improvement later adopted by the official ATA standards. By directly transferring data between memory and disk, DMA does not require the CPU/program/operating system to leave other tasks idle while the data transfer occurs.
  • SCSI (Small Computer System Interface) was an early competitor with ESDI, originally named SASI for Shugart Associates. SCSI disks were standard on servers, workstations, and Apple Macintosh computers through the mid-90s, by which time most models had been transitioned to IDE (and later, SATA) family disks. Only in 2005 did the capacity of SCSI disks fall behind IDE disk technology, though the highest-performance disks are still available in SCSI and Fibre Channel only. The length limitations of the data cable allows for external SCSI devices. Originally SCSI data cables used single ended data transmission, but server class SCSI could use differential transmission, and then Fibre Channel (FC) interface, and then more specifically the Fibre Channel Arbitrated Loop (FC-AL), connected SCSI HDDs using fibre optics. FC-AL is the cornerstone of storage area networks, although other protocols like iSCSI and ATA over Ethernet have been developed as well.
  • SATA (Serial ATA). The SATA data cable has one data pair for differential transmission of data to the device, and one pair for differential receiving from the device, just like EIA-422. That requires that data be transmitted serially. The same differential signaling system is used in RS485, LocalTalk, USB, Firewire, and differential SCSI.
  • SAS (Serial Attached SCSI). The SAS is a new generation serial communication protocol for devices designed to allow for much higher speed data transfers and is compatible with SATA. SAS uses serial communication instead of the parallel method found in traditional SCSI devices but still uses SCSI commands for interacting with SAS

Acronym	Meaning	Description
SASI	Shugart Associates System Interface	Predecessor to SCSI
SCSI	Small Computer System Interface	Bus oriented that handles concurrent operations.
SAS	Serial Attached SCSI
ATA	Advanced Technology Attachment	Successor to ST-412/506/ESDI by integrating the disk controller completely onto the device. Incapable of concurrent operations.
SATA	Serial ATA
ST-506		Seagate interface
ST-412		Seagate interface (minor improvement over ST-506)
ESDI	Enhanced Small Disk Interface	Faster and more integrated than ST-412/506, but still backwards compatible

Manufacturers

Seagate 3.5 inch 40 GB HDD.

The technological resources and know-how required for modern drive development and production mean that as of 2007, over 98% of the world's HDDs are manufactured by just a handful of large firms: Seagate, Western Digital, Samsung, and Hitachi (which owns the former disk manufacturing division of IBM). Fujitsu continues to make mobile- and server-class disks but exited the desktop-class market in 2001. Toshiba is a major manufacturer of 2.5-inch and 1.8-inch notebook disks. ExcelStor is a small HDD manufacturer.

Dozens of former HDD manufacturers have gone out of business, merged, or closed their HDD divisions; as capacities and demand for products increased, profits became hard to find, and the market underwent significant consolidation in the late 1980s and late 1990s. The first notable casualty of the business in the PC era was Computer Memories Inc. or CMI; after an incident with faulty 20 MB AT disks in 1985, CMI's reputation never recovered, and they exited the HDD business in 1987. Another notable failure was MiniScribe, who went bankrupt in 1990 after it was found that they had engaged in accounting fraud and inflated sales numbers for several years. Many other smaller companies (like Kalok, Microscience, LaPine, Areal, Priam and PrairieTek) also did not survive the shakeout, and had disappeared by 1993; Micropolis was able to hold on until 1997, and JTS, a relative latecomer to the scene, lasted only a few years and was gone by 1999, after attempting to manufacture HDDs in India. Their claim to fame was creating a new 3" form factor drive for use in laptops. Quantum and Integral also invested in the 3" form factor; but eventually gave up as this form factor failed to catch on. Rodime was also an important manufacturer during the 1980s, but stopped making disks in the early 1990s amid the shakeout and now concentrates on technology licensing; they hold a number of patents related to 3.5-inch form factor HDDs.

• 1988: Tandem Computers sold its disk manufacturing division to Western Digital (WDC), which was then a well-known controller designer.
• 1989: Seagate Technology bought Control Data's high-end disk business, as part of CDC's exit from hardware manufacturing.
• 1990: Maxtor buys MiniScribe out of bankruptcy, making it the core of its low-end disk division.
• 1994: Quantum bought DEC's storage division, giving it a high-end disk range to go with its more consumer-oriented ProDrive range, as well as the DLT tape drive range.
• 1995: Conner Peripherals, which was founded by one of Seagate Technology's co-founders along with personnel from MiniScribe, announces a merger with Seagate, which was completed in early 1996.
• 1996: JTS merges with Atari, allowing JTS to bring its disk range into production. Atari was sold to Hasbro in 1998, while JTS itself went bankrupt in 1999.
• 2000: Quantum sells its disk division to Maxtor to concentrate on tape drives and backup equipment.
• 2003: Following the controversy over mass failures of its Deskstar 75GXP range, HDD pioneer IBM sold the majority of its disk division to Hitachi, who renamed it Hitachi Global Storage Technologies (HGST).
• December 21, 2005: Seagate and Maxtor announced an agreement under which Seagate would acquire Maxtor in an all stock transaction valued at $1.9 billion. The acquisition was approved by the appropriate regulatory bodies, and closed on May 19, 2006.
• 2007: Hitachi releases the 1TB (1024 Gigabytes (GB) = 1 Terabyte (TB) ) Hitachi Deskstar 7k100.
• 2007: Western Digital (WDC) acquire Komag U.S.A, a thin-film media manufacturer, for USD 1 Billion.

See also

• Click of death
• Data recovery
• Disk Usage
• Disk formatting
• Hybrid drive
• Native command queuing
• PRML
• Solid state drive
• Superparamagnetism

External links

• Factfile: Hard disk drive - How they work from the BBC
• The Hard Disk That Changed The World at MSNBC
• TechEncyclopedia about Hard Disks
• Hard disk interfaces pinouts
• War of the Disks: Hard Disk Drives vs. Flash Solid State Disks Despatches from the magneto / flash wars
• PC Doctor takes you inside a hard drive
• Failure Trends in a Large Disk Drive Population : Disk Failures report by Google Labs
• Hard Disk Myths
• Disk Introduction: Detailed Introduction of the Disks with Graphic Details.
• Describing a c.1975 HDD