The 68HC11 (6811 or HC11 for short) is an 8-bit microcontroller (µC) family introduced by Motorola in 1985. Now produced by NXP Semiconductors, it descended from the Motorola 6800 microprocessor by way of the 6809. It is a CISC microcontroller. The 68HC11 devices are more powerful and more expensive than the 68HC08 microcontrollers, and are used in automotive applications, barcode readers, hotel card key writers, amateur robotics, and various other embedded systems. The MC68HC11A8 was the first MCU to include CMOS EEPROM.
|Motorola 68HC11 registers|
Internally, the HC11 instruction set is upward compatible with the 6800, with the addition of a Y index register. (Instructions using the Y register have opcodes prefixed with the byte 0x18). It has two eight-bit accumulators, A and B, two sixteen-bit index registers, X and Y, a condition code register, a 16-bit stack pointer, and a program counter. In addition, there is an 8 x 8-bit multiply (A x B), with full 16-bit result, and Fractional/Integer 16-bit by 16-bit Divide instructions. A range of 16-bit instructions treat the A and B registers as a combined 16-bit D register for comparison (X and Y registers may also be compared to 16-bit memory operands), addition, subtraction and shift operations, or can add the B accumulator to the X or Y index registers. Bit test operations have also been added, performing a logical AND function between operands, setting the correct conditions codes, but not modifying the operands.
Different versions of the HC11 have different numbers of external ports, labeled alphabetically. The most common version has five ports, A, B, C, D, and E, but some have as few as 3 ports (version D3). Each port is eight-bits wide except for D, which is six bits (in some variations of the chip, D also has eight bits). It can be operated with an internal program and RAM (1 to 768 bytes) or an external memory of up to 64 kilobytes. With external memory, B and C are used as address and data bus. In this mode, port C is multiplexed to carry both the lower byte of the address and data.
In the early 1990s Motorola produced an evaluation board kit for the 68HC11 with several UARTs, RAM, and an EPROM. The cost of the evaluation kit was $68.11.
The standard monitor for the HC11 family is called BUFFALO, "Bit User Fast Friendly Aid to Logical Operation." It can be stored in on-chip ROM, EPROM, or external memory (also typically EPROM). BUFFALO is available for most 68HC11 family derivatives as it generally only depends upon having access to a single UART (SCI, or Serial Communications Interface, in Motorola parlance). BUFFALO can also run on devices that do not have internal non-volatile memory, such as the 68HC11A0, A1, E0, E1, and F1 derivatives.
A MC68HC24 port replacement unit is available for the HC11. When placed on the external address bus, it replicates the original functions of B and C. Port A has input capture, output compare, pulse accumulator, and other timer functions; port D has serial I/O, and port E has an analog to digital converter (ADC).
- Official 68HC11 Reference Manual
- Hambley, Allan R.(2011). Electrical Engineering: Principles and Applications, Pearson Higher Education. p. 417. Digitized by Google. Retrieved on May 17, 2012.
- M68HC11 Reference Manual
- comp.dsp. 1 Oct. 1996
- Handy Board Hardware
- Freescale 68HC11 (Legacy) Part Info
- Wytec 68HC11 Development Board
- A fully synthesizable VHDL implementation of the HC11 CPU
- Digital Core Design 68HC11E - HDL IP Core
- Digital Core Design 68HC11F - HDL IP Core
- Digital Core Design 68HC11K - HDL IP Core
- Win/Linux-based freeware macro cross-assembler (ASM11)
- 4MHz-bus 68HC11F1-based board