Tanks of the post–Cold War era

Japanese Type 90 tank at the JGSDF public information center. Note the large bustle area for the autoloader, as well as the configuration of the grenade launchers.

The Post Cold War era is the period in world history from the Collapse of the Soviet Union in 1991 to the present. During the Cold War (1945–1990), the Soviet domination of the Warsaw Pact led to effective standardization on a few tank designs. In comparison, France, Germany, the USA, and the UK had previously developed their own tank designs, but now tried to standardize their designs, while the smaller nations of NATO purchased or adapted these designs.

The fall of communism brought changes as United States Military was forced to cut much of its expenditure, though the level rose again to comparable heights after the War on Terror started in 2001.

After the Cold War, tank development continued into a third-generation main battle tanks and because of the effectiveness of antitank weapons, the technology advanced dramatically as well. Tanks became more survivable and their armour became thicker and much more effective.

It had seen the United States become by far the most powerful country in the world and the rise of China from a relatively weak third world country to a fledgling superpower. It has also seen the merging of most of Europe into one economy.

Overview

File:SolOline-2005-04-27-095150.jpg

A M1A1 Abrams in the Taunus Mountains north of Frankfurt during Exercise Ready Crucible in February 2005.

The main battle tank became the standard as a necessity, as it was realized that smaller medium tanks could carry guns (such as the US 90 mm, Soviet 100 mm, and especially the British L7 105 mm) that could penetrate any practical level of armor at long range. An increasing variety of anti-tank weapons and the perceived threat of a nuclear war prioritized the need for additional armor. The additional armor prompted the design of even more powerful cannons. Typical main battle tanks were as well armed as any other vehicle on the battlefield, highly mobile, and well armored.

Developments in Post Cold War

An American M1 Abrams tank destroyed in Baghdad

In 1974, the United States initiated an impressive programme to modernise its existing tank fleet and start real mass production of the M60A1, and later the M60A3; at the same time the M1 was developed. Budgets for tank design and production picked up during the administration of president Ronald Reagan, following tensions between the United States and the Soviet Union.

In response to infantry-portable and vehicle-mounted ATGMS, ever more capable defences were developed. Spaced armour, composite, explosive reactive armour, and active protection systems—like the Russian Shtora, Drozd, and Arena—were added to old and new tanks. Despite these improvements the larger missiles remained highly effective against tanks. This was demonstrated in 1991 when in a friendly fire incident, Hellfire anti-tank missiles destroyed one of the latest M1 Abrams tanks.

Gulf War/Iraq war

US Army recognition poster of T-54/55 series tanks

The Gulf War saw the US Marines still charging in with their M60 Pattons while the rest of the tank forces had Abrams. The Iraqi forces were initially regular army units, equipped with tanks such as T-54/55 tanks and T-62s. The Coalition main battle tanks, such as the U.S. M1 Abrams, British Challenger 1, and Kuwaiti M-84AB were vastly superior to the Chinese Type 69 and domestically built T-72 tanks used by the Iraqis, with crews better trained and armoured doctrine better developed.

US M1 Abrams tanks from the 3rd Armored Division along the Line of Departure.

The majority of Iraqi armored forces still used old Chinese Type 59s and Type 69s, Soviet-made T-55s from the 1950s and 1960s, and some poor quality Asad Babil tanks (domestically assembled tank based on Polish T-72 hulls with other parts of mixed origin). These machines were not equipped with up-to-date equipment, such as thermal sights or laser rangefinders, and their effectiveness in modern combat was very limited.

The Iraqis failed to find an effective countermeasure to the thermal sights and sabot rounds used by the Coalition tanks. This equipment enabled them to engage and destroy Iraqi tanks from more than three times the range that Iraqi tanks could engage coalition tanks. The Iraqi crews used training rounds against the U.S. and British tanks. These rounds (purchased in great number during the Iran-Iraq War due to their cheap price) had soft steel penetrators and thus no hope of penetrating the advanced Chobham Armour of the Coalition tanks.

In the Iraqi war in 2003, an Iraqi division the 6th Armored Division of the Iraqi Army. which was equipped with T-55s and BMP-1s defending the control of key bridges over the Euphrates River and the Saddam Canal at Nasiriyah, were decimated by US Marines with M1 Abrams, and the division as a unit rendered incapable for combat during the Battle of Nasiriyah in March 2003, during the invasion.

An Asad Babil abandoned after facing the final US thrust into Baghdad

In addition to the T-54/55 and T-62 tanks that Iraq had, the most feared to US amoured forces were the T-72 tanks in the Iraqi forces. Only Republican Guard divisions were equipped with Iraqi-modified T-72s. Many of the Iraqi T-72s were dug-in or hidden in groves, and then used to ambush the US or British tanks. In the war, the Iraqi T-72s were the preferred target for Apache helicopters and A-10s, in an attempt to diminish the combat power of Republican Guard divisions. The only chance for the Asad Babil T-72s against American tanks was to lure them to close range combat, or trying to ambush them from dug-in positions.

But even in those conditions, the M1s usually prevailed, as proven in circumstances like the Battle of Baghdad, and the drive to the capital, where dozens of Iraqi MBTs were obliterated, or near Mahmoudiyah, south of Baghdad, April 3, 2003, (Iraqi Freedom) when US tanks engaged their counterparts from just 50 yards, shattering seven enemy T-72s without losses. The Lion of Babylon T-72 was utterly outclassed by the M1 Abrams, the Challenger and by any other contemporary Western main battle tank during the 2003 invasion of Iraq.

Post Cold War Main Battle tanks

T-80

Russian T-80 at the Victory Day Parade 2005

Main article: T-80

The Russian T-80 is a third-generation main battle tank (MBT) designed and manufactured in the Soviet Union. A development of the T-64, it entered service in 1976 and was the first production tank to be equipped with a gas turbine engine for main propulsion. The T-80U was last produced in a factory in Omsk, Russia, while the T-80UD and further-developed T-84 continue to be produced in Ukraine. The T-80 and its variants are in service in Belarus, Cyprus, Kazakhstan, Pakistan, Russia, South Korea, and Ukraine. The original T-80 design uses a 1,000 horsepower gas turbine instead of a 750 horsepower diesel engine, although some later variants of the T-80 revert to diesel engine usage. The gearbox is different, with five forward and one reverse gear, instead of seven forward and one reverse. Suspension reverts from pneumatic to torsion bar, with six forged steel-aluminium rubber-tyred road wheels on each side, with the tracks driven by rear sprockets. The glacis is of laminate armour and the turret is armoured steel. The turret houses the same 125 mm 2A46 smoothbore gun as the T-72, which can fire anti-tank guided missiles as well as regular ordnance. The tracks are slightly wider and longer than on the T-64 giving lower ground pressure.

The main gun is fed by the Korzina automatic loader. This holds up to 28 rounds of two-part ammunition in a carousel located under the turret floor. Additional ammunition is stored within the turret. The ammunition comprises the projectile (APFSDS, HEAT or HE-Frag) plus the propellant charge, or the two part missile. The autoloader is an effective, reliable, combat tested system which has been in use since the mid-1960s. The propellant charge is held inside a semi-combustible cartridge case made of a highly flammable material - this is consumed in the breech during firing, except for a small metal baseplate.

A disadvantage highlighted during combat in Chechnya was the vulnerability of the T-80BV to catastrophic explosion. The reason given by US and Russian experts is the vulnerability of stored semi-combustible propellant charges and missiles when contacted by the molten metal jet from the penetration of a HEAT warhead, causing the entire ammunition load to explode.

Leopard 2

Leopard 2A5 of the German Army (Heer)

Main article: Leopard 2

The Leopard 2 was the German main battle tank (Kampfpanzer) developed by Krauss-Maffei replaced the earlier Leopard 1 as the main battle tank of the German Army. Various versions have served in the armed forces of Germany and twelve other European countries, as well as several non-European nations. The Leopard 2 first saw combat in Kosovo with the German Army and has also seen action in Afghanistan with the Danish and Canadian ISAF forces.

Minor modifications and the installation of the gunner's thermal sight were worked into the second batch of 450 vehicles Leopard 2 designated the A1; 248 by Krauss-Maffei (Chassis Nr. 10211 to 10458) and 202 by Mak (Chassis Nr. 20173 to 20347). Deliveries of the 2A1 models started in March 1982 and ended in November 1983. The two most notable changes were the modification of the ammunition racks to be identical to those in the M1 Abrams, and redesigned fuel filters that reduced refuelling time.

The most widespread version of the Leopard 2 family, the 2A4 models included more substantial changes, including an automated fire and explosion suppression system, an all-digital fire control system able to handle new ammunition types, and improved turret with flat titanium/tungsten armour. All the older models were also upgraded to 2A4 standard.

The 2A4 was also license manufactured in Switzerland as the Panzer 87 "Leopard" or Pz 87. This version included Swiss-built 7.5 mm Mg 87 machine guns and communications equipment, and featured improved NBC protection system. Switzerland operated 380 Pz 87 tanks.

At the turn of the century, Germany and the Netherlands found themselves with large stocks of tanks they had no need for after the end of the Cold War. These tanks were sold to NATO or friendly armies around the world. Among these were Austria, who received 114 vehicles, Canada (107), Chile (140), Denmark (51), Finland (139), Greece (183), Norway (52), Poland (128), Portugal (37), Singapore (96), Spain (108), Sweden (160), and Turkey (339) were among the buyers of the surplus tanks.

Challenger 2

British Challenger 2 Tank of the Royal Scots Dragoon Guards (Squadron D).

Main article: Challenger 2

The Challenger 2 is the British main battle tank (MBT) currently in service and was designed and built by the British company Vickers Defence Systems (now known as BAE Systems Land and Armaments).

Challenger 2 is an extensive redesign of the Challenger 1. Although the hull and automotive components seem similar, they are of a newer design and build than those of the Challenger 1, and fewer than 5% of components are interchangeable. Challenger 2 replaced Challenger 1 in service with the British Army and is also used by the Royal Army of Oman. It has seen operational service in Bosnia, Kosovo and Iraq.

In June 1991, after competition with other tank manufacturers' designs (including the M1A2 Abrams and the Leopard 2 (Improved)), the MoD placed a £520 million order for 127 MBTs and 13 driver training vehicles. An order for a further 259 tanks and 9 driver trainers (worth £800 million) was placed in 1994. Oman ordered 18 Challenger 2s in 1993 and a further 20 tanks in November 1997.

Challenger 2 entered service with the British Army in 1998 (with the 2nd Royal Tank Regiment in Germany), with the last delivered in 2002. It is expected to remain in service until 2035. It serves with the Royal Scots Dragoon Guards, the Royal Dragoon Guards, the Queen's Royal Hussars, the King's Royal Hussars and the 2nd Royal Tank Regiment, each of which is the tank unit of an armoured or a mechanised brigade. One squadron of the 1st Royal Tank Regiment uses Challenger 2 in a training and demonstration role.

Merkava Mark III and IV

Merkava IIID Baz fires – the Baz Fire-control system increases the Merkava's accuracy and lethality

Main article: Merkava

The Israel Defense Forces Merkava Mark III was introduced in December 1989, and had upgrades to the drivetrain, powertrain, armament, and electronic systems. The most prominent addition was the incorporation of the locally developed IMI 120 mm gun. This gun and a larger 1,200 horsepower (890 kW) diesel engine increased the total weight of the tank to 65 tonnes (143,000 lb), but the larger engine increased the maximum cruising speed to 60 km/h (37 mph).

The turret was re-engineered for movement independent of the tank chassis, allowing it to track a target regardless of the tank's movement.

The next development was the Israel Defense Forces Merkava Mark IV tank which is the most recent upgrade of the Merkava tank and has been in development since 1999. The upgrade's development was announced in an October 1999, however, new Merkava Mark IIIs continued to be produced until 2003. The first Merkava IVs were in production in limited numbers by the end of 2004.

The Merkava Mark III

The more advanced, Merkava Mark III Baz model, with weaponry highlighted

Merkava Mark III Dor Dalet BAZ Kasag, the most advanced Merkava III variant

Variants of the Merkava Mark III

Merkava Mark IV is first publicly introduced and seen in Yad La-Shiryon during Israeli Independence Day celebrations in 2002.

Merkava Mark IV (foreground)

Merkava Mark IV of the 401st Brigade during a training exercise.

The Merkava Mark IV

The model has a new fire-control system, the El-Op Knight Mark 4. Removable modular armor, from the Merkava Mark IIID, is used on all sides, including the top and a V-shaped belly armor pack for the underside. This modular system is designed to allow for damaged tanks to be rapidly repaired and returned to the field.

Tank rounds are stored in individual fire-proof canisters, which reduce the chance of cookoffs in a fire inside the tank. The turret is "dry"; no active rounds are stored in it.

Some features, such as hull shaping, exterior non-reflective paints, and shielding for engine heat plumes mixing with air particles to confuse enemy thermal imagers, were carried over from the IAI Lavi program of the Israeli Air Force to make the tank harder to spot by heat sensors and radar.

The Mark IV includes the larger 120 mm main gun of the previous versions but can fire a wider variety of ammunition, including HEAT and sabot rounds like the APFSDS kinetic energy penetrator, using an electrical semi-automatic revolving magazine for 10 rounds. It also includes a much larger 12.7 mm machine gun for anti-vehicle operations (most commonly used against technicals).

The new fire-control system enables the Merkava to shoot down helicopters such as the Russian Mil Mi-24 and the French Gazelle, both of which are used by Israel's neighbors.

The Mark IV has the Israeli-designed "TSAWS (Tracks, Springs, and Wheels System)" caterpillar track system, called "Mazkom" (Template:Lang-he) by troops. This system is designed to endure the harsh basalt rock conditions of Lebanon and the Golan Heights with minimal "track-shedding".

The tank carries the Israeli Elbit Systems BMS (Battle Management System; Hebrew: צי"ד), a centralised system that takes data from tracked units and UAVs in theater, displays it on color screens, and distributes it in encrypted form to all other units equipped with BMS in a given theater.

Type 90 tank

Japanese Type 90 tank

Main article: Type 90 Kyū-maru

The Japanese Type 90 tank, main battle tank (MBT) of the Japan Ground Self-Defense Force (JGSDF) as of 2011 was designed and built by Mitsubishi Heavy Industries as a replacement for all deployed Type 61 and Type 74 tanks, and entered service in 1990.

With the exception of the 120 mm smoothbore gun, which is made under licence from Rheinmetall of Germany, the Type 90 and its subsystems are all designed and built in Japan, leading to higher per unit costs for comparable models from NATO countries such as the M1 Abrams and the Challenger 2.

The profile of the Type 90 is similar to the original German Leopard 2 without the sloped armor, (Leopard 2 to 2A4) but unlike the Leopard 2, the Type 90 uses modular ceramic and steel composite armor, common in contemporary post-1990s tank designs. The adoption of modular composite armor design facilitates the upgrading and exchange of the armor, and its frontal armor is tested to be effective against JM-33 120 mm APFSDS projectiles from the L44 gun, while the side armor of the turret is capable of defeating up to 35 mm APDS (Armor penetration of 90 millimeters of RHA at one kilometer) projectiles.

The Type 90 is smaller than most main battle tanks with a height of 2.33 meters, a width of 3.33 meters, and weighing in at 50.2 tonnes.

AMX Leclerc

Main article: AMX Leclerc

The AMX Leclerc is the French main battle tank (MBT) built by GIAT, now Nexter of France. It was named in honour of General Philippe Leclerc de Hauteclocque who led the French element of the drive towards Paris while in command of the Free French 2nd Armoured Division (2ème DB) in World War II.

A Leclerc Main Battle Tank on manoeuvres.

The Leclerc is equipped with a GIAT (Nexter) CN120-26 120mm smoothbore cannon. This cannon is capable of firing the same NATO standard 120mm rounds as the German Leopard 2 and US M1 Abrams, but in practice only French-produced ammunition is issued. The gun is insulated with a thermal sleeve and has an automatic compressed-air fume extraction system instead of the usual bore evacuator. The Leclerc has a unique autoloading system which was specifically designed for it, and reduces the crew to three by eliminating the human loader. The turret of the Leclerc was designed around the auto-loading system in order to avoid the problems common to other tanks with an autoloader. The Leclerc autoloader allows a rate of fire of 12 shots per minute and holds 22 rounds of ready ammunition; it can accommodate up to six different types of ammunition at once, although like most autoloader systems it cannot change ammunition types once a round has been loaded. The most common types are the armour piercing fin-stabilised discarding sabot (APFSDS) with a tungsten core and the high explosive anti-tank (HEAT) round. There are 18 other rounds available for reload. A Leclerc tank can fire while traveling at a speed of 50 km/h on a target 4,000 metres away. The gun is 52 calibres long instead of the 44 calibres common on most tanks of the Leclerc's generation, giving the rounds a higher muzzle velocity.

The Leclerc is also equipped with a 12.7 mm coaxial machine gun and a remote-controlled 7.62mm machine gun, whereas most other NATO tanks use 7.62mm weapons for both their coaxial and top machine gun mounts; the major exception is the American M1 Abrams, which has a 7.62mm coaxial machine gun and two top-mounted machine guns, one 7.62mm and one 12.7mm.

The Leclerc has the GALIX combat vehicle protection system from GIAT, which fires a variety of smoke grenades and infra red screening rounds, as well as anti-personnel grenades.

The hull and the turret are made of welded steel fitted with modular armour, which can be replaced easily for repair or upgraded over the years. The French army in the late seventies rejected Chobham armour as being overly specialised in its optimisation to defeat hollow charge-weapons; it therefore opted to develop their own composite arrangement to defeat both hollow charge and sabot round. Due to the introduction of modernized threats, the batch 3 has a new armour package, including composite armor, titanium insert and on the sides of the turret, ERA blocks.

In service only since 1992 (after the Persian Gulf War), the Leclerc has no notable experience in true warzone environments, but has seen deployment on multiple low-intensity conflicts, including 15 Leclerc stationed in Kosovo (KFOR) and others in Lebanon (UNIFIL) in the context of UN peace-keeping operations, where their performance was judged satisfactory by French officials.

Until 2010, 13 Leclerc were deployed in the south Lebanon for a peacekeeping mission with UNIFIL.

C1 Ariete

Italian Ariete main battle tank of the Italian Army

Main article: C1 Ariete

The C1 Ariete main battle tank of the Italian Army, was developed by a consortium formed by Iveco-Fiat and Oto Melara (aka CIO, Consorzio Iveco Oto Melara). The chassis and engine were produced by Iveco, while the turret and fire-control system were produced by Oto Melara.The Ariete is mounted with a 120 mm smoothbore Oto Melara cannon, autofrettaged and stress-hardened to increase durability over extended periods of fire, allowing the use of APFSDS and HEAT rounds.

The Ariete's armour is a steel and composite blend, similar to the British Challenger 2 and the American M1 Abrams.

The Ariete features two side-mounted, electronically fired grenade launchers. Each launcher consists of four barrels which can be intermixed with either smoke or chaff grenades. The smoke grenades are capable of shrouding the tank from visual or thermal detection, while the chaff grenades disperse the tank's radar cross section. The tank is fully NBC protected.

Arjun

Indian Arjun main battle tank

Main article: Arjun (tank)

The Arjun (Sanskrit: अर्जुन) is India's third generation main battle tank developed by India's Defence Research and Development Organization (DRDO), for the Indian Army. The tank is named for Arjun, a character in the Indian epic, Mahabharata.

The Arjun features a 120 mm main rifled gun with indigenously developed APFSDS ammunition, one 7.62 mm coaxial machine gun, and a 12.7 mm machine gun. It is powered by a single MTU multi-fuel diesel engine rated at 1,400 hp, and can achieve a maximum speed of 70 km/h (43 mph) and a cross-country speed of 40 km/h (25 mph). It has a four-man crew: commander, gunner, loader and driver. Automatic fire detection and suppression and NBC protection systems are included. All-round anti-tank warhead protection by the newly developed Kanchan armour is claimed to be much higher than available in comparable third generation tanks.

Al-Khalid

[[File:Al-Khalid IDEAS 2012.jpg|thumb|left|Pakistan[[main battle tank] Al-Khalid MBT on display at IDEAS 2012 in November 2012]]]

Main article: Al-Khalid (tank)

The Al-Khalid tank (Template:Lang-ur—Al-Xālid Ṫaiŋk, pronounced [əl-ˈxɑːlɪd̪ ʈæːŋk] lit. The Immortal Tank) and MBT-2000 refers to the main battle tank of Pakistan of jointly developed variants made by Pakistan and China during the 1990s. About 300 Al-Khalid tanks were in service with the Pakistan Army as of 2009. Operated by a crew of three and armed with a 125 mm smooth-bore tank gun that is reloaded automatically, the tank uses a modern fire-control system integrated with night-fighting equipment and is capable of firing many types of anti-tank rounds as well as guided anti-tank missiles. Al-Khalid is named after the 7th-century Muslim commander Khalid bin al-Walid (592-642 AD).

An evolution of Chinese and Soviet tanks, the design is considerably smaller and lighter than most Western main battle tanks. It is based on the Chinese Type 90-II, which combined technologies from several Soviet and Western tanks. The Al-Khalid is unusual in that it was designed to be adaptable for manufacture, so that it can be easily integrated with a variety of foreign engines and transmissions. The current production variant of the Al-Khalid uses a diesel engine and transmission supplied by the KMDB design bureau of Ukraine. The first production models entered service with the Pakistan Army in 2001.

Type 99

Chinese Type 99 tank

Main article: Type 99

The Chinese Type 99 tank (Chinese: 99式; pinyin: Jiǔjiǔ shì), also known as ZTZ-99 and WZ-123, was developed from the Type 98G (in turn, a development of the Type 98), is a third generation main battle tank (MBT) of the Chinese People's Liberation Army. It is made to compete with other modern tanks and is currently the most advanced MBT fielded by China.

Small-scale production of the Type 98 was begun in time for the tank to be featured in the PRC's National Day parade in 1999.

Following the completion of the Type 98, research into improved versions of the tank continued within the Chinese government. These programs produced the Type 98G, a refined iteration of the Type 98 with a better reliability record. At the end of 2001, the first batch of 40 Type 98G tanks entered service with the regular Army. The Type 98G eventually gave rise to what is now known as the Type 99, which was officially revealed by the government in 2001. The final version of the Type 99 included a 1,500-horsepower engine, as opposed to its immediate predecessor's 1,200-horsepower powertrain. Also added were a Leopard 2A5-style sloped-arrow armor plate on the front of the turret, and additional composite armor layers on the sides.

In part due to its high cost, the tank is not expected to be deployed in large numbers, unlike earlier Chinese designs such as the Type 59. Because of the limited nature of its production, the Type 99 is currently only operated by the PLA's most elite divisions.

See also

• History of the tank
• Tanks in World War I
• Comparison of World War I tanks
• Tanks of the interwar period
• Tanks in World War II
• Comparison of early World War II tanks
• Cold War Tanks
• Post-Cold War Tanks
• Armoured fighting vehicle