GWR 4200 Class

GWR 4200 Class
Preserved 4200 Class no. 4247 on the Gloucestershire Warwickshire Railway
Type and origin Power type Steam Designer Churchward Builder GWR Build date 1910-1923
Specifications Configuration: ​  • Whyte 2-8-0T Gauge 4 ft 8+1⁄2 in (1,435 mm) standard gauge Driver dia. 4 ft 7+1⁄2 in (1,410 mm) Loco weight 81 long tons 12 cwt (182,800 lb or 82.9 t) Fuel type Coal Boiler pressure 200 psi (1,400 kPa) Cylinders two outside Cylinder size 18+1⁄2 in × 30 in (470 mm × 762 mm)
Performance figures Tractive effort 31,450 lbf (139,900 N)
Career Power class GWR: D BR: 7F Axle load class GWR: Red Disposition Five preserved, remainder scrapped

The Great Western Railway (GWR) 4200 Class is a class of 2-8-0T steam locomotives.

History

Development

After the GWR took over operations and then absorbed the various South Wales based railways from the late 1800s, operational practice on most was defined by moving heaving coal trains on sharp, steep and undulating tracks. Thus many of these railways - especially the dominant Taff Vale Railway - specified and used an 0-6-2T, which gave maximum tractive effort whilst riding well on the undulating track.

With coal trains increasing in size and scale, the GWR needed to develop a more powerful locomotive to meet these requirements, on what were relatively short haul routes. Thus in 1906, Chief Engineer G.J. Churchward took the basic design of his GWR 2800 Class, and adapted it. After proposing a 2-8-2T design, Churchward developed the UK's first 2-8-0 Tank engine, through concerns that the longer frames required for a 2-8-2T would restrict operation in the South Wales Valleys.

Churchward upgraded the power of the design, modifying the frames to hold a GWR standard No.4 boiler over the 2800 Class standard No.1. The flanges of the second and third driving wheels were made thinner, and the coupling rods between the third and fourth sets of driving wheels used spherical joints, all to create side play and hence flexibility in operations. The prototype No.4201 was out shipped from Swindon Works in 1910 under Lot No.142, with a straight back bunker capable of containing three tonnes of coal. In 14months of testing, it easily proved itself capable of negotiating curves down to 2 chains (130 ft; 40 m) in radius.

Operations

Put into production in 1912 under Lot No.187, the first locomotives were No.s 4202 - 4221, which had both top feed boilers and curved upper bodies to their coal bunkers to provide 3.5 tonnes of coal carrying capacity. Working 1000+ ton coal trains through the South Wales Valleys, from coal mines to ports, the large boilers and restricted loading gauge resulted in narrow side tanks. Although passing numerous water stops along their routes, because of the class’s heavy water consumption and limited tank capacity, they were nicknamed “Water Carts”. 105 4200s were built between 1910 and 1923.

Modifications

In 1919, from Lot No.213 (4262 - 4285) onwards, the coal bunker was built six inches taller, increasing coal capacity to 4 tons. In 1921, having also run out of allocation numbers, the class received its first major upgrade. Increasing cylinder diameter from 18.5 inches (470 mm) to 19 inches (480 mm) increased tractive effort to 33,170 pounds, thus creating the distinctive later GWR 5205 Class.

The last batch of the 5205 Class produced pre-World War 2 were lot No.266 of 1930, producing No's 5275-5294. However, due to the Stock Market Crash of 1929, and a resultant down turn in coal exports to Europe, a number of the 4200 Class having been returned to Swindon for overhaul, had in fact been stored there. To increase their operational ability across the wider GWR network, Chief Engineer Charles Collett took the board-agreed decision to alter this batch in production to 2-8-2T by adding a bolt-on 4 feet (1.22 m) extension to the frames to accommodate a pair of rear trailing wheels, which took the coal capacity up to 6 tons and water tanks to 2500 gallons. This created the GWR 7200 Class 2-8-2T. Due to demands from the Operational Department for more of the 7200 Class, from the stored 4200 Class locomotives at Swindon, fourteen were rebuilt between 1937 and 1939 as 7200 Class locomotives. Although operationally banned from certain goods yards, most 7200's found work across the GWR system, mostly deployed on iron ore and stone trains from Banbury.

In later years many of the remaining 4200's were upgraded to 5205 specification with outside steam pipes, larger cylinders and in some cases curved frames at the front end.

Withdrawal

All bar one, No.4224, passed in the ownership of British Railways on nationalisation. By the end of steam on the former GWR system, 18 were still working at the start of 1965, the last withdrawn being No.4268 in August 1965.

Preservation

Five have been preserved, with all rescued from Woodham Brothers scrapyard in Barry, Vale of Glamorgan, South Wales.

Number	Year Built	Withdrawn	Location	Status	Notes
4247			Bodmin and Wenford Railway	Operational	In 5205 specification, outside steampipes but straight footplate. Left Barry in April 1985.
4248			Swindon Steam Railway Museum	Static museum exhibit	In 5205 specification. Left Barry in May 1986. Conserved rather than restored, on show dismantled as if it were "in the Swindon Works."
4253			Kent and East Sussex Railway	Under restoration	Has 5275 style footplate with a raised section over the cylinders. Left Barry in August 1987, stored at Pontypool and Blaenavon Railway until 2011, then sold to group from K&ESR.
4270			Gloucestershire Warwickshire Railway	Operational	Retains original inside steam pipes. Left Barry in July 1985, owned by Jeremy Hosking.
4277 Hercules			Dartmouth Steam Railway	Operational	Retains original inside steam pipes. Left Barry in June 1986.

Models

In 2012, Hornby released models of the 4200 class in both BR black and GWR green.