5.56×45mm NATO with measurement, left to right: bullet, empty case, complete round with bullet in casing
|Place of origin||United States|
|In service||Since 1962|
|Wars||Since Vietnam War|
|Parent case||.223 Remington|
|Case type||Rimless, bottleneck|
|Bullet diameter||5.70 mm (0.224 in)|
|Neck diameter||6.43 mm (0.253 in)|
|Shoulder diameter||9.00 mm (0.354 in)|
|Base diameter||9.58 mm (0.377 in)|
|Rim diameter||9.60 mm (0.378 in)|
|Rim thickness||1.14 mm (0.045 in)|
|Case length||44.70 mm (1.760 in)|
|Overall length||57.40 mm (2.260 in)|
|Case capacity||1.85 cm3 (28.5 gr H2O)|
|Rifling twist||178 mm or 229 mm (1 in 7 in or 9 in, originally 1 in 14 in)|
|Primer type||Small rifle|
|Maximum pressure (EPVAT)||430.00 MPa (62,366 psi)|
|Maximum pressure (SCATP 5.56)||380.00 MPa (55,114 psi)|
|Test barrel length: 508 mm (20.0 in)
Source(s): NATO EPVAT testing, QuickLOAD, SAAMI, C.I.P.
The 5.56×45mm NATO (official NATO nomenclature 5.56 NATO) is an intermediate cartridge developed in the United States and originally chambered in the M16 rifle. Under STANAG 4172, it is a standard cartridge for NATO forces as well as many non-NATO countries. It is derived from, but not identical to, the .223 Remington cartridge. If the bullet impacts at high enough velocity and yaws in tissue, fragmentation creates a rapid transfer of energy which can result in dramatic wounding effects.
- 1 History
- 2 Cartridge dimensions
- 3 Performance
- 4 5.56 mm NATO versus .223 Remington
- 5 Comparison of 5.56 mm NATO versus 7.62 mm NATO
- 6 Military cartridge types
- 7 Use
- 8 See also
- 9 References
- 10 Further reading
- 11 External links
The previous standard NATO rifle cartridge was the 7.62×51mm NATO, sold commercially as the .308 Winchester rifle cartridge, and designed to replace the .30-06 Springfield rifle cartridge in the U.S. military. At the time of selection, there had been criticism that the 7.62×51mm NATO was too powerful for light weight modern service rifles, causing excessive recoil, and that the weight of the ammunition did not allow for enough rate of fire in modern combat.
The British had extensive evidence with their own experiments into an intermediate cartridge since 1945 and were on the point of introducing a .280 inch (7 mm) cartridge when the selection of the 7.62×51mm NATO was made. The FN company had also been involved. The concerns about recoil and effectiveness were effectively overruled by the US within NATO, and the other NATO nations accepted that standardization was more important at the time than selection of the ideal cartridge. However, whilst the 7.62×51mm NATO round became NATO standard the US was already engaged in research of their own, which ultimately led to the 5.56×45mm NATO cartridge.
During the late 1950s, ArmaLite and other U.S. firearm designers started their individual Small Caliber/High Velocity (SCHV) assault rifle experiments using the commercial .222 Remington cartridge. When it became clear that there was not enough powder capacity to meet U.S. Continental Army Command's (CONARC) velocity and penetration requirements, ArmaLite contacted Remington to create a similar cartridge with a longer case body and shorter neck. This became the .222 Remington Special. At the same time, Springfield Armory's Earle Harvey had Remington create an even longer cartridge case then known as the .224 Springfield. Springfield was forced to drop out of the CONARC competition, and thus the .224 Springfield was later released as a commercial sporting cartridge known as the .222 Remington Magnum. To prevent confusion with all of the competing .222 cartridge designations, the .222 Remington Special was renamed the .223 Remington. After playing with their own proprietary cartridge case design, the .224E1 Winchester, Winchester eventually standardized their case dimensions, but not overall loaded length, with the .222 Remington Special to create a cartridge known as the .224E2 Winchester. With the U.S. military adoption of the ArmaLite M16 rifle in 1963, the .223 Remington was standardized as the 5.56×45mm NATO. As a commercial sporting cartridge the .223 Remington was only introduced in 1964.
The 5.56×45mm cartridge, along the M16 rifle, were initially adopted by U.S. infantry forces as interim solutions to address the weight and control issues experienced with the 7.62×51mm round and M14 rifle. In the late 1950s, the Special Purpose Individual Weapon program sought to create flechette rounds to allow troops to fire sabot-type projectiles to give a short flight time and flat trajectory with a muzzle velocity of 1,200 metres per second (3,900 ft/s) to 1,500 metres per second (4,900 ft/s). At those speeds, factors like range, wind drift, and target movement would no longer affect performance. Several manufacturers produced varying weapons designs, including traditional wooden, bullpup, "space age," and even multi-barrel designs with drum magazines. All used similar ammunition firing a 1.8 mm diameter dart with a plastic "puller" sabot filling the case mouth. While the flechette ammo had excellent armor penetration, there were doubts about their terminal effectiveness against unprotected targets. Conventional cased ammunition was more accurate and the sabots were expensive to produce. The SPIW never created a weapons system that was combat effective, so the M16 was retained, and the 5.56 mm round was kept as the standard U.S. infantry rifle cartridge.
In a series of mock-combat situations testing in the early 1960s with the M16, M14 and AK-47, the Army found that the M16's small size and light weight allowed it to be brought to bear much more quickly. Their final conclusion was that an 8-man team equipped with the M16 would have the same fire-power as a current 11-man team armed with the M14. U.S. troops were able to carry more than twice as much 5.56×45mm NATO ammunition as 7.62×51mm NATO for the same weight, which would allow them a better advantage against a typical NVA unit armed with AK-47s.
|Rifle||Cartridge||Cartridge weight||Weight of loaded magazine||Max. 10 kilogram ammo. load|
|M14||7.62×51mm||393 gr (25.4 g)||20 rd mag @ 0.68 kg||14 mags @ 9.52 kg for 280 rds|
|M16||5.56×45mm||183 gr (11.8 g)||20 rd mag @ 0.3 kg||33 mags @ 9.9 kg for 660 rds|
|AK-47||7.62×39mm||281 gr (18.2 g)||30 rd mag @ 0.92 kg*||10 mags @ 9.2 kg for 300 rds|
(*AK-47 magazines are much heavier than M14 and M16 magazines)
In 1977, NATO members signed an agreement to select a second, smaller caliber cartridge to replace the 7.62×51mm NATO cartridge. Of the cartridges tendered, the 5.56×45mm NATO was successful, but not the 55 gr M193 round used by the U.S. at that time. The wounds produced by the M193 round were so devastating that many consider it to be inhumane. Instead, the Belgian 62 gr SS109 round was chosen for standardization. The SS109 used a heavier bullet with a steel tip and had a lower muzzle velocity for better long-range performance, specifically to meet a requirement that the bullet be able to penetrate through one side of a steel helmet at 600 meters. This requirement made the SS109 (M855) round less capable of fragmentation than the M193 and was considered more humane.
The 5.56×45mm NATO inspired an international tendency towards relatively small sized, light weight, high velocity military service cartridges that produce relatively low bolt thrust and free recoil impulse, favoring light weight arms design and automatic fire accuracy. Similar intermediate cartridges were developed and introduced by the Soviet Union in 1974 (5.45×39mm) and by the People's Republic of China in 1987 (5.8×42mm).
Americans would define the shoulder angle at alpha/2 = 23 degrees. The common rifling twist rate for this cartridge is 178 mm (1 in 7 in) or 229 mm (1 in 9 in), 6 grooves, Ø lands = 5.56 mm, Ø grooves = 5.69 mm, land width = 1.88 mm and the primer type is small rifle.
According to the official NATO proofing guidelines the 5.56×45mm NATO case can handle up to 430 MPa (62,000 psi) piezo service pressure. In NATO regulated organizations every rifle cartridge combo has to be proofed at 125% of this maximum pressure to certify for service issue. This is equal to the C.I.P. maximum pressure guideline for the .223 Remington cartridge, that is the 5.56×45mm NATO parent cartridge.
The 5.56×45mm NATO SS109/M855 cartridge (NATO: SS109; U.S.: M855) with standard 62 gr. lead core bullets will penetrate approximately 38 to 51 cm (15 to 20 in) into soft tissue in ideal circumstances. As with all spitzer shaped projectiles it is prone to yaw in soft tissue. However, at impact velocities above roughly 762 m/s (2,500 ft/s), it may yaw and then fragment at the cannelure (the crimping groove around the cylinder of the bullet). These fragments can disperse through flesh and bone, inflicting additional internal injuries.
Fragmentation, if or when it occurs, imparts much greater damage to human tissue than bullet dimensions and velocities would suggest. This fragmentation effect is highly dependent on velocity, and therefore barrel length: short-barreled carbines generate less muzzle velocity and therefore lose wounding effectiveness at much shorter ranges than longer-barreled rifles. Proponents of the hydrostatic shock theory contend that the rapid transfer of energy also results in wounding effects beyond the tissue directly crushed and torn by the bullet and fragments. These remote wounding effects are known as hydrostatic shock.
SS109/M855 NATO ball can penetrate up to 3 mm (0.12 in) of steel at 600 meters. According to Nammo, a Norwegian ammunition producer, the 5.56×45mm NATO M995 armour piercing cartridge can penetrate up to 12 mm (0.47 in) of RHA steel at 100 meters.
The Swedish military has measured the bullet velocities of SS109/M855 military cartridges at 4 m (13.1 ft) from the muzzle fired from differing barrel lengths:
|Barrel length||SS109/M855 V4 bullet velocity||V4 velocity loss|
|210 mm (8.3 in)||723 m/s (2,372 ft/s)||41 m/s (135 ft/s)|
|240 mm (9.4 in)||764 m/s (2,507 ft/s)||32 m/s (105 ft/s)|
|270 mm (10.6 in)||796 m/s (2,612 ft/s)||29 m/s (95 ft/s)|
|300 mm (11.8 in)||825 m/s (2,707 ft/s)||18 m/s (59 ft/s)|
|330 mm (13.0 in)||843 m/s (2,766 ft/s)||23 m/s (75 ft/s)|
|360 mm (14.2 in)||866 m/s (2,841 ft/s)||12 m/s (39 ft/s)|
|390 mm (15.4 in)||878 m/s (2,881 ft/s)||14 m/s (46 ft/s)|
|420 mm (16.5 in)||892 m/s (2,927 ft/s)||14 m/s (46 ft/s)|
|450 mm (17.7 in)||906 m/s (2,972 ft/s)||9 m/s (30 ft/s)|
|480 mm (18.9 in)||915 m/s (3,002 ft/s)||7 m/s (23 ft/s)|
|508 mm (20.0 in)||922 m/s (3,025 ft/s)||-|
There has been much criticism of the allegedly poor performance of the bullet on target, especially the first-shot kill rate when the muzzle velocity of the firearms used and the downrange bullet deceleration do not achieve the minimally required terminal velocity over 750 m/s (2,500 ft/s) at the target to cause fragmentation. This wounding problem has been cited in incidents beginning in the Vietnam War, first Gulf War, Somalia, and in the conflicts in Iraq and Afghanistan. In lab testing of the 5.56×45mm NATO standard SS109/M855 cartridge, it has been shown that the bullets do not fragment reliably or consistently from round-to-round, displaying widely variable performance. In several cases, yawing did not begin until 177 to 254 mm (7.0 to 10.0 in) of penetration. This was with all rounds coming from the same manufacturer. This lack of wounding capacity typically becomes an increasingly significant issue as range increases (e.g., ranges over 50 m (55 yd) when using an M4 carbine or 200 m (220 yd) when using an M16 rifle) or when penetrating heavy clothing, but this problem is compounded in shorter-barreled weapons. The 368 mm (14.5 in) barrel of the U.S. military's M4 carbine generates considerably less muzzle velocity than the longer 508 mm (20.0 in) barrel found on the M16 rifle, and terminal performance can be a particular problem with the M4.
The 5.56×45mm NATO standard SS109/M855 cartridge was designed for maximum performance when fired from a 508 mm (20.0 in) long barrel, as was the original 5.56 mm M193 cartridge. Greater length barrels actually result in no improvement or a decrease in muzzle velocities due to the propellant burning characteristics induced pressure versus barrel friction relationship. Shorter barrels produce a greater flash and noise signature, and the addition of a suppressor to a short barreled AR family rifle can make it unreliable, as the reduced time for the propellant to burn in the barrel and higher muzzle pressure levels at the suppressor entrance can cause faster cycling and feeding issues. Unless the gas port can be regulated or adjusted for higher pressures, suppressors for short barreled 5.56×45mm NATO firearms must be larger and heavier than models for standard length rifles to function reliably. SS109/M855 cartridges fired from barrels under about 254 mm (10.0 in) in length do not have enough muzzle velocity energy to cause bullet fragmentation that occurs only at terminal velocities of over 750 m/s (2,500 ft/s) on impact, reducing the wounding capacity.
Combat operations the past few months have again highlighted terminal performance deficiencies with 5.56×45mm 62 gr. M855 FMJ. These problems have primarily been manifested as inadequate incapacitation of enemy forces despite them being hit multiple times by M855 bullets. These failures appear to be associated with the bullets exiting the body of the enemy soldier without yawing and fragmenting.
This failure to yaw and fragment can be caused by reduced impact velocities as when fired from short barrel weapons or when the range increases. It can also occur when the bullets pass through only minimal tissue, such as a limb or the torso of a thin, small statured individual, as the bullet may exit the body before it has a chance to yaw and fragment. In addition, bullets of the SS109/M855 type are manufactured by many countries in numerous production plants.
Although all SS109/M855 types must be 62 gr. FMJ bullets constructed with a steel penetrator in the nose, the composition, thickness, and relative weights of the jackets, penetrators, and cores are quite variable, as are the types and position of the cannelures. Because of the significant differences in construction between bullets within the SS109/M855 category, terminal performance is quite variable – with differences noted in yaw, fragmentation, and penetration depths. Luke Haag's papers in the AFTE Journal (33(1):11–28, Winter 2001) also describes this problem.—
If 5.56 mm bullets fail to upset (yaw, fragment, or deform) within tissue, the results are relatively insignificant wounds, similar to those produced by .22 long rifle bullets – this is true for all 5.56x45mm bullets, including both military FMJ and OTM (open tip match) and civilian JHP/JSP designs used in law enforcement. As expected, with decreased wounding effects, rapid incapacitation is unlikely: enemy soldiers may continue to pose a threat to friendly forces and violent suspects can remain a danger to law enforcement personnel and the public.
This failure of 5.56x45mm NATO bullets to yaw and fragment can be caused by reduced impact velocities as when fired from short-barreled weapons or when the range to the target increases. Failure to yaw and fragment can also occur when the bullets pass through only minimal tissue, such as a limb or the chest of a thin, small statured individual, as the bullet may exit the body before it has a chance to yaw and fragment. Two other yaw issues: Angle-of-Attack (AOA) variations between different projectiles, even within the same lot of ammo, as well as Fleet Yaw variations between different rifles, were elucidated in 2006 by the Joint Service Wound Ballistic Integrated Product Team (JSWB-IPT), which included experts from the military law enforcement user community, trauma surgeons, aero ballisticians, weapon and munitions engineers, and other scientific specialists. These yaw issues were most noticeable at close ranges and were more prevalent with certain calibers and bullet styles — the most susceptible being 5.56x45mm NATO FMJ ammunition like SS109/M855 and M193.—
Despite complaints that the 5.56x45mm NATO round lacks stopping power, others contend that animal studies of the wounding effects of the 5.56×45mm NATO round versus the 7.62×39mm have found that the 5.56x45mm NATO round is more damaging, due to the post-impact behavior of the 5.56 mm projectile resulting in greater cavitation of soft tissues. The US Army contended in 2003 that the lack of close range lethality of the 5.56×45mm NATO was more a matter of perception than fact. With controlled pairs and good shot placement to the head and chest, the target was usually defeated without issue. The majority of failures were the result of hitting the target in non-vital areas such as extremities. However, a minority of failures occurred in spite of multiple hits to the chest.
Some have contended that shot placement is the most important parameter in determining the lethality of a bullet. Shots to the central nervous system and major blood vessels are the primary forms of incapacitation. Difficulty with the 5.56x45mm NATO at range can be attributed to training, as only a few nations taught shooting beyond 200–300 meters to regular soldiers. At a marksmanship training workshop held in Spain in March 2010, some participants went from using 150 rounds over 28 hours to engage targets out to 200 meters, to using 1,000 rounds over two weeks engaging targets out to 400 meters. Sweden and Canada had requirements to shoot 3-5 rounds, respectively, in the prone or kneeling position at 100 meters with a max dispersion of 150 mm (5.9 in). Due to their inability to adjust rifle fire for dispersion, target movement, unknown ranges, and wind drift, Swedish ISAF units relied on .50 BMG heavy machine guns for long-range. The effect of barrel length is also questioned. A barrel length reduction of 59 percent results in a reduced muzzle velocity for 5.56x45mm NATO ball of only 21 percent. The length differences between a 508 mm (20.0 in) M16 barrel and 368 mm (14.5 in) M4 barrel results in a trajectory difference of 16 mm (0.63 in) at 250 m. A bullet fired from an M16 has a greater terminal velocity than one from an M4 only up to 50 meters longer distance. Time of flight difference from the two barrel lengths is 2 cm (0.79 in) per meter per second at 300 meters. Underperformance can be attributed to errors in range estimation, target lead, wind, firing position, and stress under fire, which are factors that can be resolved through training.
Advances have been made in 5.56 mm ammunition. The U.S. Military had adopted for limited issue a 77-grain (5.0 g) "Match" bullet, type classified as the Mk 262. The heavy, lightly constructed bullet fragments more violently at short range and also has a longer fragmentation range. Originally designed for use in the Mk 12 SPR, the ammunition has found favor with special forces units who were seeking a more effective cartridge to fire from their M4A1 carbines. Commercially available loadings using these heavier (and longer) bullets can be prohibitively expensive and cost much more than military surplus ammunition. Additionally, these heavy-for-caliber loadings sacrifice even more penetrative ability than the M855 round (which has a steel penetrator tip). Performance of 5.56×45 mm military ammunition can generally be categorized as almost entirely dependent upon velocity in order to wound effectively. Heavy OTM bullets enhance soft tissue wounding ability at the expense of hard-target/barrier penetration.
U.S. Special Forces had sought to create a round that had increased power out of carbine M4 barrels and compact SCAR-L barrels, while increasing hard target performance. Developmental efforts led to the creation of the Mk318. The bullet uses an open-tip design to inflict damage on soft tissue, and has a brass rear to penetrate hard targets. The tip and lead core fragments consistently even out of short barrels, while the rear moves through once the front impacts. It has more consistent performance because it is not yaw-dependent like the M855; the nose fragments upon impact and solid rear penetrator continues to move relatively straight. This makes the Mk318 effective against personnel with or without body armor. The round also increases accuracy, from 3-5 minute of angle with the M855 from an M4A1 barrel to 1.71 MOA at 300 yards and 1.67 MOA at 600 yards from a 14 in (360 mm) SCAR-L barrel.
For general issue, the U.S. Army adopted the M855A1 round in 2010 to replace the M855. The primary reason was pressure to use non-lead bullets. The lead slug is replaced by a copper alloy slug in a reverse-drawn jacket, with a hardened steel penetrator extending beyond the jacket, reducing lead contamination to the environment. The M855A1 offers several improvements other than being lead-free. It is slightly more accurate, has better consistency of effect in regards to wounding ability, and has an increased penetrating capability. The round can better penetrate steel, brick, concrete, and masonry walls, as well as body armor and sheet metal. It penetrates 3⁄8 in (9.5 mm) of mild steel at 350 meters, which the M855 can only do at 160 meters. The propellant burns faster, which decreases the muzzle flash and gives a higher muzzle velocity, an important feature when fired from a short barreled M4 carbine. Though the M855A1 is more expensive to produce, its increased performance compensates. One possible danger is that it generates more pressure in the chamber when fired, slightly increasing the risk of catastrophic failure of the weapon, though this has yet to occur.
The U.S. Marines adopted the Mk318 in early 2010 due to delays with the M855A1. This was a temporary measure until the M855A1 was available for them, which occurred in mid-2010 when the Army began to receive the rounds. Both the Mk138 and M855A1 weigh the same and have similar performance, and both have better performance than the M855 against all targets. SOCOM spent less money developing the Mk318 and is marginally better than the M855A1 in some situations, but costs more per round. The Army spent more developing the M855A1 which performs as well or nearly as well as the Mk318, but is cheaper per round and has the advantage of being lead-free. While SOCOM constantly looks for better equipment, the Army and Marines have far more troops to supply and buys more ammunition.
If the 5.56mm bullet is moving too slowly to reliably fragment on impact, the wound size and potential to incapacitate a person is greatly reduced. There have been numerous attempts to create an intermediate cartridge that addresses the complaints of 5.56 NATO's lack of stopping power along with lack of controllability seen in rifles firing 7.62 NATO in full auto. Some of alternative cartridges like the 6.8mm Remington SPC focused on superior short-range performance by sacrificing long-distance performance due to relatively short engagement distances typically observed in modern warfare. Others, like the 6.5mm Grendel, are attempts at engineering an all purpose cartridge that could replace both the 5.56 and 7.62 NATO rounds. The 300 AAC Blackout (7.62×35mm) round was designed to have the power of the 7.62×39mm to use in an M4 platform using M4-type magazines. None of these cartridges gained any significant traction beyond sport shooting communities. While both the 6.8 SPC and 6.5 Grendel perform better than the 5.56 NATO, they have their own drawbacks, including lower muzzle velocity and decreased magazine capacity. The 6.8 SPC's short and light bullet has poor long-range ballistics and a poor ballistic coefficient, and the 6.5 Grendel's case has poor ergonomics and a larger case diameter.
By late 2004, the 6.8 mm SPC was in limited use with U.S. Special Operators. However, it was not adopted for widespread use due to resistance from officials on changing calibers and the development of the 6.5 Grendel, which had better accuracy past 500 meters. In 2007, both the U.S. SOCOM and the U.S. Marine Corps decided not to field weapons chambered in 6.8 mm due to logistical and cost issues.
General Purpose Cartridge
The conflict in Afghanistan has caused a fundamental shift in the consideration of small-arms cartridge use. Previously, the normal maximum range for small-arms engagements was around 300 meters. In Afghanistan, Taliban fighters with PKM machine guns and Dragunov SVD sniper rifles launched half their attacks between 300 and 900 meters. Over a quarter of engagements took place between 500 and 900 meters. British soldiers were initially only armed with 5.56 mm L85A2 rifles, L86A2 light support weapons, and L110A1 Para light machine guns. The L85/86 had an effective range of 300 meters and the L110A1 had an effective range of 200–300 meters. Over half of small-arms engagements took place beyond the effective range of standard British infantry weapons, and 70 percent were beyond the effective range of a short barreled M4 Carbine. 5.56 mm rounds also have poor suppressive effects against concealed positions at those ranges. The suppressive effect of a small-arms bullet is directly proportional to the loudness of the sonic bang it generates, which in turn that is directly proportional to its size. 5.56 mm rounds have half the suppressive radius of 7.62 mm rounds, which can be further decreased by wind drift at long-range. Complaints are compounded by laboratory tests that reveal that 85 percent of SS109/M855 bullets do not yaw until at least 120 mm (4.7 in) of penetration, which would be most of the way through the body.
Weapons like the 7.62 mm Mk 14 Enhanced Battle Rifle and Mk 48 machine gun became increasingly utilized by U.S. troops, as their need for effective fire beyond 500 meters was considered worth the weight increase. British troops turned to carrying the 7.62 mm L7A2 GPMG and L129A1 marksman rifle. The 7.62 NATO cartridge is larger, heavier, and produces three to four times as much recoil as the 5.56. This makes it difficult to fire in rapid semi-automatic mode and almost uncontrollable on automatic. Users of the SCAR-H battle rifle claim that only the first round of an automatic burst would hit the target. Retaining both the 5.56 for close-range fighting and the 7.62 for long-range has its disadvantages, as only half the squad would be well-equipped for each situation. This also hurts logistics and the ability to interchange ammunition, as a squad would be armed with magazine-fed 5.56 and 7.62 rifles, and belt-fed 5.56 and 7.62 machine guns.
There are several ways to address 5.56 mm deficiencies. One is to improve the load of the bullet. The U.S. has developed the Mk 262, Mk318, and M855A1 to give better performance from short barreled carbines, improve barrier penetration, and give more reliable terminal effectiveness. However, they have similar exterior ballistics to the M855 and do not meet the need for long-range coverage, as the rounds are limited by the small size and power of the cartridge. Furthermore, the open-tip designs and fragmentation ability of the rounds may not be accepted by other NATO countries due to their interpretation of Declaration III of the Hague Convention. Another way would be to return entirely to the 7.62×51mm cartridge. The principle 7.62 round is the M80, which delivers terminal effectiveness through its size and power. It does not yaw rapidly on impact and although it has a longer range, it has poor long-range performance due to its relatively light bullet, which sheds velocity quickly. A low-recoil loading could be adopted for rifles, like the 138 gr (8.9 g) bullet used in the Japanese Howa Type 64, while keeping full-power M80 rounds for machine guns and marksman rifles. The disadvantages with this are interchangeability in combat would be difficult because the rifles' gas systems would need to be adjusted to use the different ammo types, the ammunition load for riflemen would be doubled, and the weight of machine gun ammo would be the same. The open-tipped Mk319 loading has good terminal effectiveness and barrier penetration, but greater weight and recoil still limits the usefulness of 7.62 mm rounds. Another option would be to keep the 7.62 for long-range use, and replace the 5.56 for short to medium-range use. The 6.8×43mm SPC has better terminal effectiveness and barrier penetration with little increased weight or recoil. The 6.8 mm round was kept short and relatively light to keep its overall length the same as the 5.56, so longer-range performance is limited.
A more radical alternative is to create a new cartridge that can replace both rounds. This concept has become known as a General Purpose Cartridge (GPC), which could create one common round for a dismounted infantry section. With the size and performance class of the 6.8 mm for short-range, balancing the right caliber and bullet could theoretically match the long-range performance of the 7.62 with much lower weight and recoil. There have been several attempts to create and adopt a general purpose cartridge. The U.S. had previously sought to adopt a reduced power, general-purpose cartridge with the .276 Pedersen in the early 1930s. It was intended to replace the .30-06 Springfield but was rejected in 1932 because of large stocks of available .30-06 ammunition. The U.S. Army also felt it offered insufficient long-range performance, as their mindset was for long-range semi-automatic fire. The British created a reduced-power round with the .280 British for trials to select NATO's first standard rifle and machine gun cartridge. The bullet had less weight and recoil than the American 7.62×51mm and had more energy at long range, but was defeated by the U.S. insistence of their cartridge to be powerful enough to replace the .30-06 in machine guns. In the 1970s, the U.S. created the 6 mm SAW round for use in a squad automatic weapon. Because of logistics concerns over adopting a third rifle caliber, development was abandoned when a better 5.56 mm round was promised, which arrived as the M855.
A comparison of M80 7.62 mm, M855 5.56 mm, 115 gr 6.8 mm SPC, and 123 gr 6.5 Grendel shows very different performances. 7.62 mm starts out very powerful at the muzzle, but drops significantly out to 1,000 meters. 6.8 mm is more powerful than 5.56 mm, but also decreases with range due to its short bullet. 6.5 mm starts with similar power to 6.8 mm, but has slightly greater energy than 7.62 mm at 1,000 meters. The 6.5 Grendel's low-drag, lead-cored bullet is longer and more aerodynamic, giving it a flatter trajectory and less wind drift despite its lower muzzle velocity. 6.8 SPC and 6.5 Grendel were designed to be the same length as the 5.56 to fit in a converted AR-15 rifle, constraining certain bullet designs. A new GPC in a new family of weapons would not be constrained. While the 6.5 Grendel appears to fill the role of a GPC, it achieves the required performance through a long barrel and heavy lead-cored bullet. Out of a shorter carbine barrel, it would need an even heavier round for the same ballistics. It is constrained by its overall length if a lead-free round were made, as it would need to be longer to be the same weight as the lead-cored round, which would require filling up more case space and losing propellant; even more would be lost using tracer bullets. If a light hybrid polymer/metal case were to be used, it would be thicker and further reduce propellant space. The desire for lead-free cartridges and lighter case designs mean that even though the 6.5 Grendel has better performance than most existing rounds, it does not have the case capacity to match 7.62 mm performance, and so cannot be the GPC.
The United States Army Armament Research, Development and Engineering Center (ARDEC) Small Caliber Munitions Technology Branch released the results of tests carried out to determine the optimum caliber for a military rifle in March 2011. 5.56 mm and 7.62 mm rounds were tested against 6 mm, 6.35 mm, and 6.8 mm rounds, all loaded with lead-free copper and steel bullets. Criteria examined included: penetration; terminal effectiveness; accuracy; initial, retained, and striking energy; wind drift; stowed kills; and recoil. The study found that the 6.35 and 6.8 calibers comprehensively outperformed the others in their overall balance of characteristics. In 2012, a study from the U.S. Army Marksmanship Unit (AMU) concluded that the optimum cartridge for a future infantry carbine should have a length and diameter greater than 5.56×45mm, be 6.5 mm caliber, have a muzzle energy of 2,500 J (1,800 ft·lb), and use low-drag bullets (G7 BC of .250+) to provide better long-range performance over the 7.62 mm with more retained velocity and energy, a flatter trajectory, and less wind drift. A Small Arms Intermediate Caliber Study done by the Canadian Department of Applied Military Science as part of their Small Arms Modernization and Replacement Project shows similar findings. They compared the ballistics of NATO 5.56 mm and 7.62 mm with commercial 6.5 mm and 6.8 mm rounds. Their conclusion was that 6.5 mm rounds with low-drag bullets had the best long-range performance and resistance to external factors.
Two 6.5 mm cartridge designs, one lead-free weighing 7 g (110 gr) and one lead-cored weighing 8 g (120 gr), have both been calculated to outperform M80 7.62 mm and M855 5.56 mm out to 1,000 meters, with all fired from 20 in barrels. At that distance, the 6.5 mm rounds have higher velocities, more energy, and more armor and barrier penetration. 7.62 drops 15 meters and 5.56 drops 17 meters below the line of sight, while both 6.5 rounds drop 12.5 meters. Against a 10 mph cross-wind at that range, 7.62 is blown sideways 4.25 m and 5.56 moves 5.4 m, while the 8 gram and 7 gram 6.5 rounds move 3 m and 3.3 m respectively. Time of flight for 7.62 is 2.1 seconds to travel 1,000 meters, while 5.56 takes 2.2 seconds, and both 6.5 rounds take 1.9 seconds. The 5.56 cartridge has the advantages of being the lightest and having the least recoil, but poor performance at long range makes it incapable of fulfilling the role of a GPC.
A general purpose cartridge used by U.S. forces would likely be lead-free and have a steel penetrator like the M855A1. European cartridges would need to comply with their interpretations of the Hague and Geneva Conventions, likely having a jacket that fully encloses the nose and sides of the bullet and doesn't expand or readily fragment on impact. Ball rounds would need to penetrate intermediate barriers and maintain its trajectory after passing through. Armor-piercing and tracer rounds also need to be developed. The GPC could be utilized through the Lightweight Small Arms Technologies effort to develop cased telescoped ammunition and caseless ammo, as well as weapons to fire them. Creating a lighter form of ammunition and new weapons would be a missed opportunity if current projectiles were used with their known deficiencies.
5.56 mm NATO versus .223 Remington
The 5.56 mm NATO and .223 Remington cartridges and chamberings are similar but not identical. While the cartridges are identical other than powder load, the chamber leade, i.e. the area where the rifling begins, is cut to a sharper angle on some .223 commercial chambers. Because of this, a cartridge loaded to generate 5.56mm pressures in a 5.56mm chamber may develop pressures that exceed SAAMI limits when fired from a short-leade .223 Remington chamber.
The dimensional specifications of 5.56 NATO and .223 commercial brass casings are identical. The cases tend to have similar case capacity when measured, with variations chiefly due to brand, not 5.56 vs .223 designation. The result of this is that there is no such thing as "5.56 brass" or ".223 brass", the differences in the cartridges lie in pressure ratings and in chamber leade length, not in the shape or thickness of the brass.
In July 2012, the Army solicited a request for vendors to supply alternative cartridge cases to reduce the weight of an M855A1 5.56 mm round by at least 10 percent, as well the for 7.62 NATO and .50 BMG rounds. The cartridge cases must maintain all performance requirements when fully assembled, be able to be used by the Lake City Army Ammunition Plant, must be manufactured in quantities totaling approximately 45 million per year. Polymer-cased ammunition is expected as a likely lightweight case technology. A hybrid polymer/metal version of a conventional cartridge case would be thicker than regular cases and reduce the amount of space for the propellant.
C.I.P. defines the maximum service and proof test pressures of the .223 Remington cartridge equal to the 5.56 mm NATO, at 430 MPa (62,366 psi). This differs from the SAAMI maximum pressure specification for .223 Remington of 380 MPa (55,114 psi), due to CIP test protocols measuring pressure using a drilled case, rather than an intact case with a conformal piston, along with other differences. NATO uses NATO EPVAT pressure test protocols for their small arms ammunition specifications.
Because of these differences in methodology, the CIP pressure of 430 MPa (62,366 psi) is the same as a SAAMI pressure of 380 MPa (55,114 psi), which is reflected in US Military specifications for 5.56 mm NATO, which call for a mean maximum pressure of 55,000 PSI (when measured using a protocol similar to SAAMI).
These pressures are generated and measured using a chamber cut to 5.56 NATO specifications, including the longer leade. Firing 5.56mm NATO from a chamber with a shorter .223 Remington leade can generate pressures in excess of SAAMI maximums.
The 5.56 mm NATO chambering, known as a NATO or mil-spec chamber, has a longer leade, which is the distance between the mouth of the cartridge and the point at which the rifling engages the bullet. The .223 Remington chambering, known as SAAMI chamber, is allowed to have a shorter leade, and is only required to be proof tested to the lower SAAMI chamber pressure. To address these issues, various proprietary chambers exist, such as the Wylde chamber (Rock River Arms) or the ArmaLite chamber, which are designed to handle both 5.56×45mm NATO and .223 Remington equally well. The dimensions and leade of the .223 Remington minimum C.I.P. chamber also differ from the 5.56 mm NATO chamber specification.
Using commercial .223 Remington cartridges in a 5.56 mm NATO chambered rifle should work reliably, but until recently, it was believed this was less accurate than when fired from a .223 Remington chambered gun due to the longer leade. Although that may have been true in the early 1960s when the two rounds were developed, recent testing has shown that with today's ammunition, rifles chambered in 5.56mm can also fire .223 ammunition every bit as accurately as rifles chambered in .223 Remington, and the 5.56mm chamber has the additional advantage of being able to safely fire both calibers. Using 5.56 mm NATO mil-spec cartridges (such as the M855) in a .223 Remington chambered rifle can lead to excessive wear and stress on the rifle and even be unsafe, and SAAMI recommends against the practice. Some commercial rifles marked as ".223 Remington" are in fact suited for 5.56 mm NATO, such as many commercial AR-15 variants and the Ruger Mini-14 (marked ".223 cal"), but the manufacturer should always be consulted to verify that this is acceptable before attempting it, and signs of excessive pressure (such as flattening or gas staining of the primers) should be looked for in the initial testing with 5.56 mm NATO ammunition.
It should also be noted that the upper receiver (to which the barrel with its chamber are attached) and the lower receiver are entirely separate parts in AR-15 style rifles. If the lower receiver has either .223 or 5.56 stamped on it, it does not guarantee the upper assembly is rated for the same caliber, because the upper and the lower receiver in the same rifle can, and frequently do, come from different manufacturers – particularly with rifles sold to civilians or second-hand rifles.
In more practical terms, as of 2010 most AR-15 parts suppliers engineer their complete upper assemblies (not to be confused with stripped uppers where the barrel is not included) to support both calibers in order to satisfy market demand and prevent any potential problems.
Comparison of 5.56 mm NATO versus 7.62 mm NATO
|Cartridge||Model||Cartridge size||Cartridge weight||Bullet weight||Velocity||Energy|
|5.56mm NATO||M855||5.56×45mm||12.31 g (190 gr)||4.02 g (62 gr)||945.5 m/s (3,100 ft/s)||1,797 J|
|7.62mm NATO||M80||7.62×51mm||25.40 g (392 gr)||9.33 g (147 gr)||838.0 m/s (2,749 ft/s)||3,275 J|
Benefits of the 5.56 NATO claimed over the 7.62 NATO are equal lethality against soft targets, half the mass and volume, reduced recoil, noise, and muzzle flash, better penetration of metal plates, flatter trajectory and shorter time of flight out to 700 meters, weapons chambered for it are lighter, and higher hit probability. Hit probability refers to a soldier being able to concentrate on stance, weapon control, aiming, and trigger pull in spite of their weapon's recoil and noise, which has a noticeable difference between the two cartridges. While the 7.62 mm has twice the energy of the 5.56 mm, it is only required if the target is protected by armor. Both rounds will normally pass right through an enemy out to over 600 m. A 5.56 mm round fired from a 20 in (510 mm) barrel has a flatter trajectory than a 7.62 mm round from the same barrel length. A 7.62 mm round from a 20 in barrel has the same trajectory as a 5.56 mm round fired from the 14.5 in (370 mm) barrel of an M4. A typical 7.62 NATO-chambered weapon has a barrel length of 20 in, and reaches half of its velocity after 80 mm (3.1 in) of travel down the bore. Shortening the barrel for close-quarters use results in decreased muzzle velocity and increased muzzle pressure.
Military cartridge types
- Cartridge, Ball, F1 (Australia): 5.56×45mm FN SS109 equivalent produced by Thales Australia, formerly Australian Defence Industries (ADI).
- Cartridge, Ball, F1A1 (Australia): 5.56×45mm with optimized projectile having a modified boat tail length and meplat diameter, redesigned case thickness, new primer cup design, and AR2210V01 propellant. [green tip]
- Cartridge, Blank, F3 (Australia): 5.56×45mm Blank cartridge produced by Thales Australia, formerly Australian Defence Industries (ADI).
- Cartridge, Ball, SS109 (Belgium): 5.56x45mm 61-grain [3.95 g] Semi-Armor-Piercing cartridge w/. steel penetrator produced by Fabrique Nationale. Adopted in 1979 as the NATO standard.
- Cartridge, Ball, C77 (Canada): 5.56×45mm FN SS109 equivalent used in the C7, C8 and C9 type weapons. Made by General Dynamics Canada.
- Cartridge, Blank, C79 (Canada): 5.56×45mm blank cartridge used in the C7, C8 and C9 type weapons. Also made by General Dynamics Canada.
- Cartridge, Ball, DM11 (Germany): 5.56×45mm 4.1 g dual core ball cartridge w/steel core, produced by RUAG Ammotec. [green tip]
- Cartridge, Tracer, DM21 (Germany): 5.56×45mm tracer compliment to DM11, also produced by RUAG Ammotec. [orange tip]
- Cartridge, Ball, L2A1 (United Kingdom): 5.56×45mm M193 equivalent produced by Radway Green.
- Cartridge, Ball, L2A2 (United Kingdom): 5.56×45mm FN SS109 equivalent produced by Radway Green.
- Cartridge, Tracer, L1A1 (United Kingdom): 5.56×45mm tracer compliment to L2A1, produced by Radway Green. [red tip]
- Cartridge, Tracer, L1A2 (United Kingdom): 5.56×45mm tracer compliment to L2A2, produced by Radway Green. [red tip]
- Cartridge, Caliber 5.56 mm, Ball, M193 (United States): 5.56×45mm 55-grain [3.56 g] ball cartridge.
- Cartridge, Caliber 5.56 mm, Grenade, M195 (United States): 5.56×45mm grenade launching blank.
- Cartridge, Caliber 5.56 mm, Tracer, M196 (United States): 5.56×45mm 54-grain [3.43 g] tracer cartridge. [red or orange tip].
- Cartridge, Caliber 5.56 mm, Dummy, M199 (United States): 5.56x45mm dummy cartridge, non firing, indented case.
- Cartridge, Caliber 5.56 mm, Blank, M200 (United States): 5.56×45mm violet-tipped blank cartridge.
- Cartridge, Caliber 5.56 mm, Ball, M202 (United States): 5.56×45mm 58-grain FN SSX822 cartridge.
- Cartridge, Caliber 5.56 mm, Ball, XM287 (United States): 5.56×45mm 68-grain ball cartridge produced by Industries Valcartier, Inc. An Improved version was also produced designated XM779.
- Cartridge, Caliber 5.56 mm, Tracer, XM288 (United States): 5.56×45mm 68-grain tracer cartridge produced by Industries Valcartier, Inc. An Improved version was also produced designated XM780.
- Cartridge, Caliber 5.56 mm, Grenade, M755 (United States): 5.56×45mm grenade launching blank specifically for the M234 launcher.
- Cartridge, Caliber 5.56 mm, Ball, XM777 (United States): 5.56×45mm ball cartridge.
- Cartridge, Caliber 5.56 mm, Tracer, XM778 (United States): 5.56×45mm tracer cartridge.
- Cartridge, Caliber 5.56 mm, Ball, M855 (United States): 5.56×45mm 62-grain FN SS109-equivalent ball cartridge with a steel penetrator tip over a lead core in a partial copper jacket. [green tip]
- Cartridge, Caliber 5.56 mm, Ball, M855 Lead Free (United States): 62-grain bullet with a steel penetrator tip over a tungsten-composite core in a partial copper jacket. Primarily used during training in countries with strict lead disposal laws. [green tip]
- Cartridge, Caliber 5.56 mm, Ball, M855A1 (United States): 62-grain bullet w/ a 19-grain steel penetrator tip over a copper alloy core. [bronze tip]
- Cartridge, Caliber 5.56 mm, Tracer, M856 (United States): 5.56×45mm 63.7-grain FN L110 tracer cartridge. Provides red visible light and lacks a steel penetrator. [orange tip]
- Cartridge, Caliber 5.56 mm, Tracer, M856A1 (United States): 5.56×45mm 56-grain Lead Free Slug (LFS) Tracer with similar ballistic performance to the M855A1 and improved trace to range consistency.
- Cartridge, Caliber 5.56 mm, Plastic, Practice, M862 (United States): Short Range Training Ammo (SRTA) has a smaller charge than standard ball, reducing its aimed range to 250 meters, and fires a plastic bullet. The M2 training bolt must be used in the M16 Rifle / M4 Carbine when using SRTA for the weapon to cycle properly due to its lower power. It is used during training on shooting ranges near built-up or populated areas. [Brass primer, Aluminum case and Blue plastic projectile].
- Cartridge, Caliber 5.56 mm, Armor Piercing, M995 (United States): 5.56×45mm 52-grain AP cartridge with a tungsten core. [black tip].
- Cartridge, Caliber 5.56 mm, Tracer, XM996 (United States): 5.56×45mm so-called "Dim Tracer" with reduced effect primarily for use with night vision devices. [red tip?]
- Cartridge, Caliber 5.56 mm, Frangible, MK 255 Mod 0 (United States): 5.56×45mm 62-grain Reduced Ricochet Limited Penetration (RRLP) round with copper/polymer composite core for training and operational use.
- Cartridge, Caliber 5.56 mm, Special Ball, Long Range, Mk 262 Mod 0/1 (United States): 5.56×45mm 77-grain Open-Tipped Match/Hollow-Point Boat-Tail cartridge. Mod 0 features Sierra Matchking bullet, while Mod 1 features either Nosler or Sierra bullet.
- Cartridge, Caliber 5.56 mm, MK318 MOD 0 enhanced 5.56 mm ammunition (United States): 5.56×45mm 62-grain Open-Tipped Match Boat-Tail cartridge.
- Cartridge, 5.56 mm, Ball, MLU-26/P (United States): Early USAF designation for 5.56×45mm ball cartridge produced by Remington.
- Cartridge, 5.56 x 45 mm, Ball, M1A3 (South Africa): 56-grain FMJ Ball round based on the M193 cartridge. It was used with the R4 assault rifle.
In 1970, NATO decided to standardize a second rifle caliber. Tests were conducted from 1977 to 1980 using U.S. XM177 5.56 mm, Belgian SS109 5.56 mm, British 4.85x49mm, and German 4.7x33mm caseless. No weapon could be agreed upon, as many were prototypes, but the SS109 was found to be the best round and standardized on October 28, 1980. The SS109 was developed in the 1970s for the FN FNC rifle and the FN Minimi machine gun. To increase the range of the Minimi, the round was created to penetrate 3.5 mm of steel at 600 meters. The SS109 had a steel tip and lead rear and was not required to penetrate body armor. Barrels required at least a 1:9 in rifle twist, but needed a 1:7 in rifle twist to fire tracer ammunition. The U.S. designated the SS109 cartridge the M855 and first used it in the M16A2 rifle. The 62-grain round was heavier than the previous 55-grain M193. While the M855 had better armor penetrating ability, it is less likely to fragment after hitting a soft target. This lessens kinetic energy transfer to the target and reduces wounding capability. The M855 is yaw dependent, meaning it depends on the angle upon which it hits the target. If at a good angle, the round turns as it enters soft tissue, breaking apart and transferring its energy to what it hits. If impacting at a bad angle, it could pass through and fail to transfer its full energy. The SS109 was made to pierce steel helmets at long range from the Minimi, not improve terminal performance on soft tissue from rifles or carbines. In Iraq, troops that engaged insurgents at less than 150 yards found that M855 rounds did not provide enough stopping power. In addition to not causing lethal effects with two or more rounds, they did not effectively penetrate vehicle windshields, even with many rounds fired at extremely close range. In Afghanistan, troops found that M855 rounds also suffered at long ranges. Although 5.56 mm rifles have an effective range of 450–600 meters, the M855 bullet's performance falls off sharply beyond 300 meters. The ranges are even shorter for short-barreled carbines. Half of small-arms attacks were launched from 300-900 meter ranges. An M855 fired from an M4 Carbine has severely degraded performance beyond 150 meters.
The maximum effective point target range of an M4 carbine with M855 rounds is 500 meters, with a maximum effective area target range of 600 meters. These mark the greatest distances the rounds can be expected to accurately hit the target, not the ranges that they have terminal effectiveness against them. Because the M855 is yaw dependent it requires instability in flight to deform upon hitting the target. It is the most stable in flight between 150–350 meters, potentially lessening its effectiveness if it strikes an enemy between those distances. In addition to this, tests have shown that 5.56 mm bullets fragment most reliably when traveling faster than 2,500 ft/s (760 m/s). From full-length 20 in rifle and machine gun barrels, rounds are kept above this velocity out to 200 meters. An M855 from an M4 has a muzzle velocity of 2,970 ft/s (910 m/s), but that is reduced to 2,522 ft/s (769 m/s) by 150 meters. Even if it impacts at optimum speeds, 70 percent of 5.56 mm bullets will not begin to yaw until 4.7 in (120 mm) of tissue penetration. 15 percent more begin to yaw after that distance, so up to 85 percent of rounds that hit do not start to fragment until nearly 5 in of penetration. Against small statured or thin combatants, the M855 has little chance of yawing before passing through cleanly and leaving a wound cavity no bigger than the bullet itself. The factors of impact angle and velocity, instability distance, and penetration before yaw reduce the round's predictable effectiveness considerably in combat situations.
On June 24, 2010, the United States Army announced it began shipping its new 5.56 mm cartridge, the M855A1 Enhanced Performance Round, to active combat zones. During testing, the M855A1 performed better than M80 7.62×51mm NATO ball ammunition against certain types of targets (particularly hardened steel), blurring the performance differences that previously separated the two cartridges. The US Army Picatinny Arsenal stated that the new M855A1 offers improved hard target capability, more consistent performance at all distances, enhanced dependability, improved accuracy, reduced muzzle flash, and higher velocity compared to the M855 round. Further, the Army stated the new M855A1 ammunition is tailored for use in M4 carbines, but should also give enhanced performance in M16 rifles and M249 light machine guns. The new 62-grain (4 g) projectile or bullet used in the M855A1 round has a copper core with a 19-grain (1.2 g) steel "stacked-cone" penetrating tip. The M855A1 cartridge is sometimes referred to as "green ammo" because it fires a lead free projectile. It is not necessarily more lethal than the M855, but performs more consistently every time it hits a soft target and retains its performance at longer distances. The EPR can penetrate a 3⁄8 in (9.5 mm) thick steel barrier from an M4 at 350 meters and from an M16 at 400 meters. Ballistics for both rounds are similar and don't require weapons to be re-zeroed, but if they are the EPR can be slightly more accurate. The steel-tip penetrator of the M855A1 is noticeably separated from the jacket of the bullet and can spin, but this is part of the design and does not affect performance. The M855A1 costs only 5 cents more per round than the M855. The M855A1 bullet has a greater length than the M855. Because steel and copper are less dense than lead, the bullet is lengthened inside the case to achieve the same weight as its predecessor.
The M855A1 was put on hold in August 2009 due to the experimental bismuth-tin alloy core exhibiting undependable ballistics at high temperatures. The US Army has since replaced the bismuth-tin alloy core with one of solid copper eliminating the heat issue. The United States Marine Corps purchased 1.8 million rounds in 2010, with plans to adopt the round to replace the interim MK318 SOST rounds used in Afghanistan when the M855A1 project was delayed.
On a media day at Aberdeen Proving Ground on May 4, 2011, reports were given about the M855A1's performance in the field since it was issued 11 months earlier. One primary advantage given by the round is its consistent performance against soft targets. While the older M855 was yaw-dependant, which means its effectiveness depends on its yaw angle when it hits a target, the M855A1 delivers the same effectiveness in a soft target no matter its yaw angle. The new SMP-842 propellant in the round burns quicker in the shorter M4 carbine barrel, ensuring less muzzle flash and greater muzzle velocity. The M855A1 was able to penetrate 3⁄8 inch (9.5 mm) of steel plate at 300 meters. The round even penetrated concrete masonry units, similar to cinder blocks, at 75 meters from an M16 and at 50 meters from an M4, which the M855 could not do at those ranges. Its accuracy is maintained and sometimes increased, as it was able to shoot a 2 inch group at 600 meters. February 2011 was the first time the M855A1 was used more than the M855, and approximately 30 million M855A1 rounds have been fielded from June 2010 to May 2011.
The M855A1 was put to the test at the 2012 National Rifle Association's National High-Power Rifle Championship at Camp Perry, Ohio in August 2012. The shooter for the Army was Rob Harbison, a contractor supporting small caliber ammunition capability development at Fort Benning Georgia. This was a special event for the Project Manager for Maneuver Ammunition Systems and the Army's Maneuver Center of Excellence as it was an opportunity to showcase the capabilities of the Enhanced Performance Round. With an M16 loaded with M855A1 ammo, Harbison fired a perfect 200 points in the Coast Guard Trophy Match, which is 20 shots fired from the sitting position at 200 yards, finishing 17th out of 365 competitors. He also scored a perfect 100 on the final string of ten shots during the Air Force Cup Trophy Match, fired at 600 yards from the prone position, which is 10 shots in a row within the 12-inch, 10-point ring at 600 yards with combat ammunition. Harbison was happy with the performance of the EPR, with his scores showing that the Army's newest general purpose round is accurate enough to go toe-to-toe in the competition with the best ammo that can be bought or hand-loaded. Harbison even said, "I don't think I could have scored any higher if I was using match-grade competition ammunition."
Since its introduction, the M855A1 has been criticized for its propellant causing increased fouling of the gun barrel. Post-combat surveys have reported no isses with the EPR in combat. A series of tests found no significant difference in fouling between the old M855 and the M855A1. However, manufacturers have reported "severe degradation" to barrels of their rifles using the M855A1 in tests. The Army attributes pressure and wear issues with the M855A1 to problems with the primer, which they claim to have addressed with a newly designed primer. The round does increase the chamber pressure from 55,000 psi to 62,000 psi.
From June 2010 to June 2013, issuing of the M855A1 Enhanced Performance Round removed 1,994 metric tons of lead from the waste stream. 2.1 grams (32 gr) of lead are eliminated from each M855A1 projectile.
The Mk 262 is a match quality round manufactured by Black Hills Ammunition made originally for the Special Purpose Rifle (SPR). It uses a 77-grain (5.0 g) Sierra MatchKing bullet that is more effective at longer ranges than the standard issue M855 round.
Two versions of the round have been procured to date. Initial production runs, designated Mark 262 Mod 0, lacked a cannelure. Subsequent production, designated Mk 262 Mod 1, added a cannelure to the bullet for effective crimping.
According to US DoD sources, the Mk 262 round is capable of making kills at 700 meters. Ballistics tests found that the round caused "consistent initial yaw in soft tissue" between 3-4 in at ranges from 15 feet to 300 meters. Apparently it is superior to the standard M855 round when fired from an M4 or M16 rifle, increasing accuracy from 3-5 minute of angle to 2 minute of angle. It evidently possesses superior stopping power, and can allow for engagements to be extended to up to 700 meters when fired from an 18 inch barrel. It appears that this round can drastically improve the performance of any AR15 platform weapon chambered to .223/5.56 mm. Superior accuracy, wounding capacity, stopping power and range power has made this the preferred round of many Special Forces operators, and highly desirable as a replacement for the older, Belgian-designed 5.56×45mm M855 NATO round. In one engagement, a two-man special forces team reported 75 kills with 77 rounds. The Mk 262 has a higher ballistic coefficient than the M855 of (G7) .190, meaning it loses less velocity at long-range. Hard target penetration is slightly decreased.
Mk318 Mod 0
Following early engagements in Afghanistan and Iraq, U.S. Special Operations Forces reported that M855 ammunition used in M4A1 rifles was ineffective. In 2005, the Pentagon issued a formal request to the ammunition industry for “enhanced” ammunition. The only business that responded was the Federal Cartridge Company, owned by Alliant Techsystems. Working with the Naval Surface Warfare Center Crane Division, the team created performance objectives for the new ammo: increased consistency from shot to shot regardless of temperature changes, accuracy out of an M4A1 better than 2 minute of angle (2 inches at 100 yards, 3.9 inches at 300 yards), increased stopping power after passing through “intermediate barriers” like walls and car windshields, increased performance and decreased muzzle flash out of shorter barrel FN SCAR rifles, and costs close to the M855. The first prototypes were delivered to the government in August 2007. Increased velocity and decreased muzzle flash were accomplished by the type of powder used. The design of the bullet was called the Open Tip Match Rear Penetrator (OTMRP). The front of it is a hollow point backed up by a lead core, but the lead core only goes about halfway down the length of the bullet, while the rear half is solid brass. When the bullet hits a hard barrier, the front half of the bullet smooshes against the barrier, breaking it so the penetrating half of the bullet can go through and hit the target. With the lead section penetrating the target and the brass section following, it was referred to as a "barrier blind" bullet. Special Forces role in counter-terror operations allow them to follow certain law enforcement guidelines, so they could use hollow point rounds without violating the Hague Convention.
Officially designated the Mk318 Mod 0 "Cartridge, Caliber 5.56mm Ball, Carbine, Barrier", and called SOST (Special Operations Science and Technology) ammunition, the 62-grain bullet fragments consistently, even out of a 10.5 in barrel. The lead portion fragments in the first few inches of soft tissue, then the solid copper rear penetrates 18 in of tissue (shown though ballistic gelatin) while tumbling. Out of a 14 in barrel, the Mk318 has a muzzle velocity of 2,925 fps.
In February 2010, the U.S. Marine Corps adopted the Mk318 for use by infantry. To be fielded by an entire branch of the military, the round is classified as having an "open-tip" bullet, similar to the M118LR 7.62 NATO round. The SOST bullet uses a “reverse drawn” forming process. The base of the bullet is made first, the lead core is placed on top of it, and then the jacketing is pulled up around the lead core from bottom to tip. Conventional, and cheaper, bullets are made with the method of the jacket drawn from the nose to an exposed lead base. The reverse drawn technique leaves an open tip as a byproduct of the manufacturing process, and is not specifically designed for expansion or to affect terminal ballistics. The Pentagon legally cleared the rounds for Marine use in late January. The Marines fielded the Mk318 gradually and in small numbers. Initial studies showed that insurgents hit by it suffered larger exit wounds, although information was limited. SOST rounds were used alongside M855 rounds in situations where the SOST would be more effective. In July 2010, the Marines purchased 1.8 million M855A1 Enhanced Performance Rounds in, addition to millions of Mk318 rounds in service, as part of its effort to replace its M855 ammo.
5.6mm Gw Pat 90
The 5.6mm Gw Pat 90 or GP 90 (5.6 mm Rifle Cartridge 90), is the standard round used by the Swiss military in its rifle, the SIG SG 550. The cartridge is also known as the Cart 5.6mm 90 F to the French and Italian speaking Swiss militiamen. The Swiss refer to the round as the 5.6 mm Gw Pat 90, although it is interchangeable with the 5.56×45mm NATO and .223 Remington round. The Gw Pat 90 is optimized for use in 5.56 mm (.223 in) caliber barrels with a 254 mm (1:10 in) twist rate.
The Gw Pat 90 was designed for the SIG SG 550 when it came into production in 1987, replacing the SIG SG 510. Previous experience of a change in standard rifle had proved that changing the distance of fire for the training ranges was more expensive than the design of a new ammunition; this prompted the design of a cartridge nominally capable at 300 meters. The cartridge was also designed to reduce pollution by controlling lead emissions. The bullet was originally clad with a nickel alloy jacket, however, this was found to cause excessive barrel wear, so in 1998 the nickel jackets were replaced with tombac jackets. In addition, in 1999 a copper plug was added to the base of the bullet to address environmental concerns.
The ammunition is currently (2009) produced by RUAG Ammotec, a subsidiary of the RUAG group. The ammunition is manufactured in three variations: the standard FMJ round, the tracer round, and a blank round.
The FMJ cartridge has a Copper-Zinc alloy case and uses a double base propellant. The bullet is a 4.1 g (63 gr) tombac jacketed FMJ projectile with a G1 ballistic coefficient of 0.331 (ICAO) / 0.337 (Army Metro). The projectile contains approximately 95% Pb, 2% Sb, 3% Cu, and was designed for terminal ballistic instability. The required accuracy for Gw Pat 90 ammunition out of factory test barrels is 63 mm (0.72 MOA) for 10 rounds (100% radius measurement method) out to 300 m. The Gw Pat 90 cartridge dimensions are in accordance with the civilian C.I.P. standards for the .223 Remington C.I.P. chambering.
The Gw Pat 90 is used both in the Swiss military and in sport shooting. The very high level of individual training in the Swiss militia (every single soldier bearing a weapon has to shoot for qualification once a year; see Gun politics in Switzerland) and the overall use of the Gw Pat 90 by the many Swiss citizens who shoot in competitions and for amusement has resulted in significant input on its usage. Over 1 billion cartridges have been produced as of 2005.
- Express (weaponry)
- NATO EPVAT testing
- Table of pistol and rifle cartridges by year
- List of rifle cartridges
- "C.I.P. decisions, texts and tables – free current C.I.P. CD-ROM version download (ZIP and RAR format)". Archived from the original on 29 September 2008. Retrieved 2008-10-17.
- US Mil-spec MIL-C-9963F
- NATO Infantry Weapons Standardization, Per G. Arvidsson, ChairmanWeapons & Sensors Working GroupLand Capability Group 1 – Dismounted Soldier NATO Army Armaments Group
- Miller-Keane, Marie T. O'Toole (1997). Miller-Keane encyclopedia and dictionary of medicine, nursing, and allied health (6th ed. ed.). Philadelphia: Saunders. ISBN 0721662781.
- Chamberlin FT, Gun Shot Wounds, in Handbook for Shooters and Reloaders, Vol. II, Ackley PO, ed., Plaza Publishing, Salt Lake City, Utah, 1966.
- Sturtevant B, Shock Wave Effects in Biomechanics, Sadhana, 23: 579–596, 1998.
- American Rifle: A Biography, Alexander Rose (2009) p. 375-376
- Barnes, Frank C. (1972). Cartridges of the World. Northfield Il: DBI Books. p. 37. ISBN 0-695-80326-3.
- Assault Rifles and Their Ammunition: History and Prospects by Anthony G. Williams
- Springfield Armory Museum – Collection Record
- Dockery, Kevin (2007). Future Weapons. p. 102.
- Jane's Infantry Weapons 1986–1987, pg. 362
- International Legal Initiatives to Restrict Military Small Arms Ammunition W. Hays Parks∗ Copyright 2010 by W. Hays Parks International Committee of the Red Cross (ICRC) pages 1–18" (Which list International Committee of the Red Cross, Austria, Argentina, Belgium, Bolivia, Bulgaria, Burundi, Cambodia, Cyprus, Germany, Ireland, Latvia, Lithuania, Luxembourg, Mauritius, Mexico, Romania, Samoa, Slovenia, Sweden, Switzerland, etc. as parties that consider the 55 gr M193 round to be inhumane)
- Ian V. Hogg, Military Small Arms of the 20th Century, 1981
- International Legal Initiatives to Restrict Military Small Arms Ammunition W. Hays Parks∗ Copyright 2010 by W. Hays Parks International Committee of the Red Cross (ICRC) page 1-18"
- The Small Arms Review vol.10, no.2 November 2006.
- Intermediate power ammunition for automatic assault rifles
- NATO EPVAT testing
- Wound Ballistics: Basics and Applications edited by Beat P. Kneubuehl. p. 128. (2011)
- "Reading Gunshot Patterns". NIH.gov. National Institute of Health. Retrieved 14 October 2010.
- PATTERNS OF MILITARY RIFLE BULLETS by Martin L. Fackler
- Pd Igman D.D. Konjic Bosnia And Herzegovina : Ammunition. Igman.co.ba. Retrieved on 2011-01-08.
- 5.56mm (.22 Cal), nammo.com
- The Case for a General-Purpose Rifle and Machine Gun Cartridge (GPC) by Anthony G Williams
- Is there a problem with the lethality of the 5.56 NATO caliber?
- Wounding Info
- Barrel Length Studies in 5.56mm NATO Weapons - SAdefensejournal.com, 8 February 2012
- Do We Need a New Service Rifle Cartridge? - SAdefensejournal, 6 January 2012
-  Acta Chir Scand Suppl. 1982;508:211–21.
-  PROJECT MANAGER SOLDIER WEAPONS SOLDIER WEAPONS ASSESSMENT TEAM REPORT 6-03
- Is There a Problem with the Lethality of the 5.56 NATO Caliber? - SAdefensejournal.com, 6 January 2012
- The Small Arms Review vol.10, no.2 November 2006
- Jane's international defense review: IDR., Volume 39, Issues 1–6. p. 86. (2006).
- Mk 318 Mod 0: A Better Bullet, No Matter What They Call It - Cheaperthandirt.com, 27 November 2011
- A Way Forward in Contemporary Understanding of the 1899 Hague Declaration on Expanding Bullets - SAdefensejournal.com, 7 October 2013
- M855A1 – Strategypage.com, August 10, 2012
- PC Bullets Survive Afghanistan - Strategypage.com, 13 May 2011
- John Pike. "6.8x43mm SPC (Special Purpose Cartridge)". Globalsecurity.org.
- Another 7.62mm Bullet For M-16s - Strategypage.com, 8 January 2012
- Dan Lamothe. "Corps to pass on Army upgrades to M4". Army Times Publishing Company. Retrieved 13 September 2010.
- The Next NATO Rifle and Machine Gun Cartridge? - SAdefensejournal.com, 6 January 2012
- The Army’s Individual Carbine Competition: What’s Next? - SAdefensejournal.com, 24 October 2013
- .223 Remington and 5.56x45mm NATO Chamber dimensions differences
- 6mmbr.com. "223 Rem + 223 AI Cartridge Guide".
- "http://www.luckygunner.com/labs/5-56-vs-223/". Retrieved 13 June 2013.
- Army wants lightweight cartridge cases - Thefirearmblog.com, 20 July 2012
- "Cartridge Pressure Standards". Retrieved 14 June 2013.
- US Mil-spec MIL-C-9963F, MIL-C-9963G, and MIL-C-63989A(AR)
- Rock River Arms
- News and Press Releases: .223 Rem VS 5.56mm, winchester.com, 5/4/2001
- Patrick Sweeney, "Chamber Reality Check", Peterson's Rifle Shooter, Volume 16, Issue 2, March/April 2013, pp. 32–36.
- "Unsafe Arms and Ammunition Combinations" at SAAMI web site
- SAAMI on 5.56 v. .223 Remington. The Gun Zone. Retrieved on 2011-01-08.
- TECHNICAL NOTE 45: 5.56 NATO vs SAAMI .223 REMINGTON CHAMBERS, armalite.com, December 4, 2002
- 5.56mm (5.56 × 45 mm) Ammunition. Inetres.com (2005-05-03). Retrieved on 2011-01-08.
- "[Army TM 9-1005-319-23&P]"
- KE = 1/2mv2, where m is in kilograms and v is in metres per second.
- 7.62mm (7.62 × 51 mm) Ammunition. Inetres.com. Retrieved on 2011-01-08.
- Testing & Evaluating the EF88 Assault Rifle - SAdefensekournal.com, 4 March 2013
- Jane's Infantry Weapons 1986–1987 pg.363
- Jane's Infantry Weapons 1986–1987 pg.362
- British Military Cartridges The 5.56x45mm
- Gary's US Infantry Weapons Reference Guide 5.56mm (5.56 x 45 mm) Ammunition
- M855A1 Enhanced Performance Round (EPR)
- Small Caliber Ammunition Enhancing Capabilities, 20 May 2010
- Corps to use more lethal ammo in Afghanistan at www.marinecorpstimes.com
- U.S. Navy Small Arms Ammunition Advancements
- How Reliable Is the M-16 Rifle? - NYtimes.com, 2 November 2009
- Army won't field deadlier Corps round - Armytimes.com, 2 April 2010
- FUTURE INFANTRY SMALL ARMS by Anthony G Williams
- Ehrhart, Thomas P. Increasing Small Arms Lethality in Afghanistan: Taking Back the Infantry Half Kilometer. pg 30-33
- Army begins shipping improved 5.56mm cartridge
- Military.com: 'Green Ammo' Heads to Afghanistan
- U.S. Army Issues New M855A1 Ammo to Troops in Afghanistan
- "Green" bullets from Picatinny Arsenal in NJ to be used in Afghanistan
- Infantry Weapons Conference Report - SAdefensejournal.com, 9 January 2012
- Lamothe, Dan; Cox, Matthew (12 July 2010). "Corps takes a new look at green bullet". Marine Corps Times. Archived from the original on 16 July 2010. Retrieved 12 July 2010.
- Lopez, Todd. "'Green bullet' as effective as M855 round – consistently." US Army News Service, 8 May 2011.
- Picatinny's Enhanced Performance Round as effective as M855 round – consistently – Picatinny Arsenal press release, May 9, 2011
- Army's Newest General Purpose Round Shows Accuracy In Rifle Competition – Army.mil, August 28, 2012
- ATK Delivers More than 350 Million 5.56mm Enhanced Performance Rounds – ATK press release, September 13, 2012
- Army Killed New Carbine Because It Wasn’t Twice As Reliable As Current M4 - Breakingdefense.com, 14 June 2013
- Data Dump: Army ‘Black Tip’ Ammo - Kitup.Military.com, 5 May 2011
- Picatinny ammo goes from regular to unleaded - Army.mil, 1 July 2013
- AA53, Cartridge, Caliber 5.56mm Special Ball, Long Range Mk 262 Mod 0. Globalsecurity.org. Retrieved on 2011-01-08.
- D. Robert Clements (September–October 2008), "The designated marksman equation", Infantry Magazine
- USMC adopt new 5.56mm MK318 MOD 0 ammunition - Thefirearmblog.com, 17 February 2010
- Marines slow to field new ammo - Thefirearmblog.com, 27 May 2010
- Marines take a look at the new M855A1 round - Thefirearmblog.com, 14 July 2010
- Swiss Ammunition Enterprise
- About The Swiss Ammunition Enterprise Corp. (SM)
- RUAG Ammotec Sintox SWISS ORDNANCE cartridge fact sheet
- Stan Christ, "5.56mm NATO Alternatives", Special Weapons Magazine, Semi-Annual #50 2007, pp. 52–59.
|Wikimedia Commons has media related to:|
- Various photos of 5.56×45mm ammunition
- RUAG Ammotech factsheet on German Army DM11 5.56×45mm ammunition
- RUAG Ammotech factsheet on German Army DM21 5.56×45mm ammunition
- ADI brochure on 5.56mm F1 ball ammunition conforming to the design parameters of the NATO STANAG 4172 and tested with Kistler 6215 transducers at different temperatures
- The AR15.COM Ammo-Oracle
- FAS: 5.56mm Ammunition
- The Gun Zone: 5.56mm FAQ
- The Gun Zone: A 5.56mm Timeline
- I.M.I Small Arms Ammunition Division
- Small Arms
- www.swissrifles.com – The New GP 90
- RUAG Ammotec Defence Forces and Government Agencies Ammunitionpage
- RUAG Ammotec Sintox SWISS ORDNANCE cartridge fact sheet
- Swiss Ammunition Enterprise