Yamaha XS Eleven

Yamaha XS Eleven

Manufacturer	Yamaha
Also called	XS1100, XS Eleven, XS1.1
Production	1977 (MY1978) – 1983
Class	Standard
Engine	Air cooled,1,101 cc (67.2 cu in) transverse four, DOHC, carb. (4) Mikuni BS34II constant velocity
Compression ratio	1978-1979: 9.2:1 1980-1983: 9.0:1
Top speed	135 mph (217 km/h)
Power	95 hp (71 kW) @8000rpm (claimed)
Torque	66.5 lb⋅ft (90.2 N⋅m) @6500rpm (claimed)
Ignition type	Transistorized contact-less battery TCI, vacuum advance
Transmission	5-speed with drive shaft
Brakes	Front Dual 298 mm (11.7 in) single-piston floating caliper  Rear Single 298 mm (11.7 in) single-piston floating caliper
Tires	Front 3.5H19 Bridgestone  Rear 4.5H17 Bridgestone
Rake, trail	20.5°, 130 mm (5.1 in)
Wheelbase	1,530 mm (60.1 in)
Dimensions	W: 812 mm (32.0 in)
Seat height	820 mm (32.3 in)
Weight	603 lb (274 kg) (wet)
Fuel capacity	US: 20 L (5.3 US gal) EU/RoW: 24 L (6.3 US gal)
Oil capacity	3.5 L (3.7 US qt)
Fuel consumption	40.3 mpg‑US (5.8 l/100 km)

The Yamaha XS Eleven motorcycle, also called XS11 and XS1100, is a Japanese standard produced from 1977 (MY1978) to 1983, powered by an air-cooled 1,101 cc (67.2 cu in) 4-stroke, DOHC inline four-cylinder engine mounted transversely in a duplex cradle frame with swingarm rear suspension, shaft drive, and telescopic forks.

History & Technology

The XS Eleven was the first four-cylinder four-stroke motorcycle from Yamaha. It built on technology first used by Yamaha in their earlier XS 750 four-stroke triple. However, the XS 1100 engine design was in reality a completely new design with several relatively unconventional elements when compared to other inline 4-cylinder motorcycle engines of the day.

The "over-square" design of the XS 1100 engine (Bore: 71.5 mm x Stroke: 68.6 mm) is different than the "under-square" XS 750 engine which had a larger stroke than bore. The camshaft drive chain moved to the center of the engine. The XS1100 engine does not transmit power directly from the crankshaft to the clutch basket/input shaft, but rather via a wide hy-vo chain onto an intermediate jack-shaft with a cush-drive damper.

XS 1100 Engine - Upper Half of the Engine Case with Crankshaft, Cam Chain, Hyvo-chain and Jackshaft Installed

The engine rotation was therefore clockwise when viewed from the left side and not counterclockwise as all other inline four-cylinder motorcycle engines of the day. This jackshaft included a "cush-drive" shock damper needed for drive shaft drive trains. The starter also engaged the jackshaft to start the engine. The engine is mounted in rubber bushings making it an almost completely vibration-free running powerplant.

A significant advancement of the XS 1100 engine are the combustion chambers.

XS 1100 Cylinder Head with Polyspherical Combustion Chambers

To make adequate power most modern motorcycle engines of the day including the XS 750 had simple hemispherical combustion chambers with domed pistons. This design has a major drawback in relatively long flame travel during combustion and therefore requires much spark advance, which in turn can cause severe preignition in high-performance engines. To improve combustion efficiency while virtually eliminating the possibility of preignition, Yamaha designed multi-angle "polyspheric" combustion chambers that required six different machining processes during manufacturing. This new design allowed for high compression without a large piston domes and large ignition advance. The XS 1100 valves were the same as previously used in the XS 750 engine, but their angle differed from the previous 3-cylinder engine. Carburetion was delivered by four Mikuni BS34 II constant velocity (CV) carburetors and ignition via a contactless, transistorized electronic ignition unit (TCI) with vacuum advance.

When the XS Eleven was introduced, it earned a reputation as a heavy, powerful and reliable bike. It was the fastest-ever production bike in 1978, for the first time posting a sub-12 second 1/4 mile time (11.78 sec. @ 114.21 mph with a top speed of 135 mph - Cycle World 2/78). In 1978 and 1979 it won Cycle World's Ten Best Bikes as the best Touring bike.

"Nobody gets far riding the XS Eleven before they become acquainted with the fact that it's strong; we had ridden ours over hundreds of open-road miles before going to the drag strip and knew it was a bullet." Cycle Magazine had this to say of the Eleven: "...the XS is a Rolls Royce with a blown Chrysler Hemi motor..."

The handling of the XS Eleven was not as well received. "When this behemoth of a motorcycle actually hits a corner at anything approaching interesting speeds then it takes a good deal of muscle to lay it down. While the Yamaha doesn't disgrace itself in corners (not as much as some Z1000s I have known, for example) it doesn't commend itself either." Testers of the day all echoed the same story: "The XS1100 was a solid bullet in a straight line, but cornering at high speeds was done at your own risk." "Cycle warned its readers that the bike could easily go, stop and steer — just never two at the same time." 'Which Bike' magazine simply described the XS1100 as having 'a bullet proof motor, and tea trolley handling'.

North American models

The XS Eleven made its debut in September 1977 (MY 1978) as the largest displacement motorcycle in production at that time. It featured a four-cylinder dual overhead cam engine, dual front disc brakes, a rear disc brake, shaft drive and cast aluminum wheels. The XS Eleven was the most powerful mass-production motorcycle of the late 70s and posted superior performance numbers compared to its competition.

The US market XS Eleven was launched as the so-called "Standard" model (Versions: E - 1978, F - 1979 and G - 1980-81). In 1979 Yamaha followed the growing market trend for "factory custom" motorcycles by offering the XS Eleven SF "Special". Pullback handlebars, a stepped seat, a 16-inch rear wheel, a smaller capacity tear-drop gas tank, and an adjustable suspension with new air-assisted front forks created this factory custom, forerunner of the modern cruiser. The XS Eleven Special sold well in the US. Despite complaints about the poor ergonomics "What that translates to is a bike with an awkward riding position but generally excellent road manners. In fact, most of the things that irritated this staff in the way the bike rode and handled could be traced to the handlebar, which, although certainly as trendy as disco dancing, was not what the ergonomics doctor ordered for precise, comfortable control.", it became the by far best-selling XS Eleven variant in the US market. In 1980 the XS Eleven LH "Midnight Special" was launched in all global markets including the US. It was basically an all black and gold version of the XS Eleven SF Special.

Beginning with the 1980 model year from September 1979 numerous changes were made to all XS Eleven engines in order to comply with more stringent US emission regulations. The compression ratio was dropped from 9.2:1 to 9.0:1 via changes to the pistons and cylinder head, changing the shape of the combustion chamber. The intake valve size was increased from 36 mm to 38 mm and the exhaust valve size from 31 mm to 32 mm in an attempt to compensate for the reduction in compression ratio. Cam timing and cam profiles however remained unchanged. The 34mm Mikuni CV carbs remained in use but received different jetting and settings. From 1980 on there were no longer pilot jet adjustment screws installed. The jet needle was set in its leanest position. The main jets which were # 137.5 in all four carbs on 1978 and 1979 models, were reduced to #115 main jets in carbs two and three (center carbs) and # 120 main jets in carbs one and four (outside carbs). While Yamaha maintained identical performance specs on paper, period tests confirmed a slight reduction in the performance of the bike. These bikes never broke into the 11-second quarter mile as the 78-79 models had. Tests also commented that cold start and warm-up behavior had worsened noticeably and required unusually long operation of the cold start enrichment system. These 1980 - on "emission" XS Eleven bikes were easy to spot since a kickstarter shaft was no longer installed in the transmission and the kickstarter lever was no longer provided.

For the 1981 model year a dedicated touring version of the XS Eleven was launched, called the XS Eleven "Venturer". It was equipped with a full touring fairing made by Pacifico for Yamaha. XS Eleven Venturers also came with matching panniers and top case. Additionally, the Venturer included the 6.3 gallon tank from the EU XS 1100 for an increased range.

The volume production of the XS Eleven really ended in 1981 in all markets and most XS Eleven models were superseded by the one-year-only 1982 XJ1100 Maxim, which used an advanced version of the XS1100 engine. In Europe however because of the importance of more sporting motorcycles, the XS 1.1 S was built as a "sport" model until 1982 (MY 1983) to bridge the gap until Yamaha could introduce the MY 1984 FJ 1100 (and subsequently FJ1200) sport-tourers in 1983.

1978 XS1100 E (EU 2H9)

European market XS 1100

In Europe the XS 1100 "Standard" was by far the most popular model of the XS 1100 line-up. There the XS 1100 remained in production until 1983. The European Yamaha XS 1100 Standard (2H9) model differed considerably from the North American XS 1100 Standard (2H7) model (Versions: E - 1978, F - 1979 and G - 1980-81). The EU XS 1100 Standard was equipped with a larger gas tank (6.3 gallons vs. 5.3 gallons), dual horns and an EU-specific narrower, lower handlebar. The rider footpegs of the EU XS 1100 were mounted on different rear sets that positioned them higher and further back on the frame for more clearance. This required a shorter rear brake lever and a special linkage for a reversely mounted shift lever to work with these rear sets. Combined with the EU handlebar these rear sets allowed for a sportier riding position than the more relaxed, laid-back position of the US model. The EU and RoW XS1100 Standard had satin black painted engines equipped from the factory with an oil cooler system, while the US engines were all natural, unpainted aluminum (except for the Midnight Special which was all black) without an oil cooler system. Further, the rear fender of the EU version was longer and the rear turn signals were mounted to the license plate holder instead of to the rear frame as in the US version. Many EU versions also had a separate steering head lock welded to the left side of the steering head as required by law in various EU countries.

While having been the by far most popular model in the US, the 1979 - 1981 XS 1100 SF "Special" sold rather poorly in Europe. It was, except for differences required by law, identical to the US model. The European market also featured two limited production models: The 1979 XS1100 Martini with a two-piece fairing designed by John Mockett, sporting a Martini color scheme similar to the bike that Mike Hailwood used as his personal transport at the 1978 Isle of Man TT. Only 500 "Martinis" were ever built exclusively for the EU market of which 274 were sold in Germany alone and 65 in the UK. The second limited-production model was the 1981 - 1983 XS 1.1 Sport. A sporty version largely based on the XS 1100 Special but laid out more as a sports bike with a small cockpit fairing. Only 320 XS 1.1 S were sold since it was a gap-filler model. Yamaha recognized the change in market demands for more sporty bikes and built the XS 1.1 S to bridge this gap until the new FJ 1100 was ready for sale. Both of these limited production models were not available to the US market. Production of the XS 1100 LH "Midnight Special" built from 1980 to 1982 was also limited, but to greater numbers, and it was sold in all global markets.

Racing: Production and Modified Classes

The XS11 dominated the 1978 Australian motorcycle production racing circuit in 1978 and continued to victories and high place finishes in production and superbike classes through 1981. The XS Eleven's win at the 1978 Castrol Six Hour production endurance race by the Pittman's Team of Jim Budd and Roger Heyes was Yamaha's first four stroke motorcycle road racing victory at a major international event. "A key component of the race from the very start was that the motorcycles had to be completely stock, exactly as available the day after the race in dealers’ showrooms around the world, and they were rigorously inspected in both pre-race and post-race scrutineering to ensure that they were"[1]

Flack of Motor Sport Retro wrote: "While the new CBX1000 and Suzuki were out and out sports bikes, the shaft-drive XS1100, affectionately called the 'Xcessive', was more of a muscle bike come tourer. Heavier than and not as fast as its rivals, the XS1100 did have one particular ability – winning races."

"In the lead up to the Six-Hour, the XS1100 had swept the Adelaide Three-Hour, the Perth Four-Hour and the Surfers Three-Hour. The unlikely XS1100 and Pitman Yamaha rider Greg Pretty had upstaged the biggest, baddest production bikes around, confounding everyone."

In the 1979 Castrol 6 hour, XS Elevens finished second (Greg Pretty, Jim Budd) third (Len Atlee, Gary Coleman) and fourth (Roger Heyes and D. Robbins)

The XS Eleven's successful racing career was a remarkable achievement considering its shaft drive and long distance touring capabilities.

British motorcycle journalist Roland Brown, says in his book Superbikes of the Seventies: "The Yamaha's lack of reputation gives it one advantage these days, though, in that a clean XS such as this one costs less than its more successful contemporary rivals – whose performance advantage, so crucial then, is far less important now. Two decades and more after its launch, maybe the XS1100's time has finally come."

Performance

In a 1978 test by Cycle World a stock XS1100 ran a quarter mile time of 11.78 s 1/4 mile @114.21 mph (183.8 km/h) with a top speed of 135 mph (217.3 km/h).

Gallery

• 
  1978 XS Eleven F (2H7 - US version)
• 
  1979 Yamaha XS Eleven Special
• 
  1981 XS Eleven Midnight Special
• 
  1978 XS 1100 E (2H9 - EU version)
• 
  1980 XS 1.1 S (EU)

See also

• Yamaha XS750
• Yamaha XS650