Bow drill

A bow drill is a simple rotational hand-operated tool of prehistoric origin. As a "fire drill" it was commonly used to generate friction to start a fire.^[1] With time it was adapted to woodworking^[2] and other tasks that requiring drilling, such as dentistry.^[3]

The bow drill consists of a bearing block or handhold, a spindle or drill, a hearth or fireboard, and a simple bow. Other early versions of mechanical drills include the pump drill and the hand drill.^[1]

History

Bow drills were used in Mehrgarh between the 4th and 5th millennium BC.^[4] This bow drill—used to drill holes into lapis lazuli and carnelian—was made of green jasper.^[4] Similar drills were found in other parts of the Indus Valley Civilization and Iran one millennium later.^[4]

Use

The drill offers an ancient method of starting fire without matches or a lighter, a method that applies friction to generate heat. The heat eventually produces an ember in the burnt sawdust. The ember is tiny, smaller than the head of a cigarette, and fragile. Once the ember is formed it is carefully placed into a "tinder bundle" (a nest of stringy, fluffy, and combustible material). Once the ember is in the tinder bundle it is then carefully nurtured and coaxed into flame. Once the tinder bundle bursts into flame, it is placed into the fuel that has been assembled ready for ignition.

The spindle, about 30 centimetres (1 ft) long and 2 centimetres (0.8 in) in diameter is held in a hole in the bottom of the bearing block (also known as the hand piece or thimble),^[a] which is held in one hand.^[5] The spindle should end in a dull point, which touches the base board (also known as the hearth, hearth board, or fireboard).^[6] The base board should be made from spruce, cedar, balsam, tamarack, or similar, non-resinous wood.^[6] The string of the bow is wrapped once around the spindle, so that it is tight enough not to slip during operation. A variation on this is called the Egyptian Bow Drill: it attaches the string by wrapping it around multiple times, or tying it to the drill (perhaps through a hole in the drill shaft), then wrapping it.

The usual position that a person assumes whilst operating the bow drill is as follows: the right knee is placed on the ground (assuming a right-handed operator) and the arch of the left foot is on the board, pinning it in place. The left wrist, holding the handhold, is hooked around the left shin and locked in place to keep it steady so it can generate enough downward pressure and speed; achieved by pushing down with the handhold and spinning the drill. The heat of the friction between the hearth and the spindle both creates charred, fuzzy dust and causes it to ignite—forming a coal or ember. The handhold is lubricated and the spindle is carved to about thumb thickness, usually 150 to 250 millimetres (6 to 10 in) long. Another option to practice is to make the "handhold" into a "mouth-hold" piece, so it is held down by pressure from the chin/mouth, leaving both hands free.

An indentation and a "v" notch into the center of the dent is made into the fireboard and the spindle is placed on it. The notch allows a place for the dust collect while it is being abraded off the spindle and the hearth. Eventually, the friction generates heat to ignite the dust, which can be used to light tinder.

A bow drill is used to ignite an ember (left), which causes tinder to combust, creating a fire

Other methods of include drilling partway into a hearth made by lashing two sticks together from one side, and then drilling from the other side to meet this hole; or using the area where two branches separate. This is to keep the coal off wet or snow-covered ground.^{[citation needed]}

The hearth and spindle can both be constructed from any medium-soft, dry, non-resinous wood, and work best when both are made from the same piece of wood; with practice almost any wood combination can be used provided the parts contain little or no resin or moisture. The most important factor is whether the wood is dry enough to ignite, as wet wood will not work; yucca, aspen, white cedar, basswood, buckeye and most willows all work very well. Combinations such as hazel and poplar also work well. The bow should be stiff but slightly limber and around the distance from the users armpit to their fingertips. The bearing block (handhold) can be made of anything that is harder than the spindle. Bone, antler, shell and stone work best, as they can be easily greased, do not create as much friction, and do not burn; hard woods such as maple and tulip and red cedar are quite serviceable and often easier to find and work. Some effective materials used to grease the bearing block include sebum, animal and plant oils, or even moist vegetation.^{[original research?]}

Types

Pump

A pump drill is a simple tool used to make holes in light materials by hand and has been in use for centuries. The drill itself is composed of: the drill shaft, a narrow board with a hole through the center, a weight (usually a heavy disc) acting as a flywheel, and a length of cord. The weight is attached near the bottom of the shaft and the hole board is slipped over the top. The cordage is run through a hole near the top of the shaft and affixed to either end of the hole board so that it hangs just above the weight. The end of the shaft usually has a square hole made to fit certain sized auger bits or a simple triangular bit made to cut while rotating in both directions.^{[citation needed]}

To use, one hand is placed on the hole board while the other turns the shaft to wind the cord around its length, thus raising the hole board to near the top where the cord becomes taut. Placing the tip against the material to be drilled and held upright, a smooth downward pressure is exerted on the board, causing the drill to rapidly spin. Once the bottom is reached, the weight is relieved and the drill allowed to rebound re-winding the cord around the shaft and the process is repeated. It is a skill simple in concept, but takes some practice to master and greatly speeds up the process of making small holes.^[7]

Hand

The hand drill is a similar tool, but uses a longer, thinner spindle; and instead of a bearing block and bow combination, the downward pressure and spinning is achieved by rubbing the hands together around the spindle.^{[citation needed]} As the hands move downward to the base, where the drill is pinched and the hands are brought quickly to the top one at a time. This can be made unnecessary by cutting a nock at the top of the drill, tying a cord through this, and then putting your thumbs through loops in the cord. However, skilled operators can either maintain pressure with their hands almost stationary vertically; or, in a movement comparable to floating, can "float" their hands back to the top of the drill. There is a more limited choice of materials to use with this method, needing much softer materials, such as mullein, yucca, cattail, and root wood.^{[original research?]}

Strap

The strap drill is similar to the bow drill but has no bow. The socket piece is shaped to be held well by the mouth, so that both hands may be free. The strap is held between one hand and the other, and wrapped around the spindle, such that rapidly moving the hands left and right spins the spindle to create friction with the fire board as in the other techniques.

References

Footnotes

^ Daniel Carter Beard attributes this invention to the Eskimos.^[5]

Citations

^ ^a ^b Frederick Webb Hodge (1 July 2003). Handbook of American Indians North of Mexico V. 1/4. Digital Scanning Inc. pp. 402–. ISBN 978-1-58218-748-8.
^ Roger Bradley Ulrich (2007). Roman Woodworking. Yale University Press. pp. 30–. ISBN 0-300-10341-7.
^ Nisha Garg; Amit Garg (30 December 2012). Textbook of Operative Dentistry. JP Medical Ltd. pp. 103–. ISBN 978-93-5025-939-9.
^ ^a ^b ^c Kulke, Hermann & Rothermund, Dietmar (2004). A History of India. Routledge. 22. ISBN 0-415-32920-5.
^ ^a ^b Beard 2014, p. 8.
^ ^a ^b Beard 2014, pp. 9–10.
^ Primitive Technology: Cord drill and Pump drill | You Tube | Jan 22, 2016

Sources

Beard, Daniel (2014) [1920]. Camp-Lore and Woodcraft. Courier Corporation. ISBN 978-0-486-80079-0. {{cite book}}: Invalid |ref=harv (help)

External links

[6] Daniel Carter Beard attributes this invention to the Eskimos.^[5]

[Hodge2003-1] Frederick Webb Hodge (1 July 2003). Handbook of American Indians North of Mexico V. 1/4. Digital Scanning Inc. pp. 402–. ISBN 978-1-58218-748-8.

[Ulrich2007-2] Roger Bradley Ulrich (2007). Roman Woodworking. Yale University Press. pp. 30–. ISBN 0-300-10341-7.

[GargGarg2012-3] Nisha Garg; Amit Garg (30 December 2012). Textbook of Operative Dentistry. JP Medical Ltd. pp. 103–. ISBN 978-93-5025-939-9.

[Kulke&R.-4] Kulke, Hermann & Rothermund, Dietmar (2004). A History of India. Routledge. 22. ISBN 0-415-32920-5.

[FOOTNOTEBeard20148-5] Beard 2014, p. 8.

[FOOTNOTEBeard20149–10-7] Beard 2014, pp. 9–10.

[8] Primitive Technology: Cord drill and Pump drill | You Tube | Jan 22, 2016

[1]

[2]

[3]

[4]

[a]

[5]

[6]

[7]

v t e Firelighting
Campfire Bonfire Glossary
Components	Ember Fire triangle Firewood Spark Tinder Wood ash Wood fuel
Topics	Autoignition temperature Combustion Friction fire Minimum ignition energy Smouldering
Early starters	Burning glass Solar Spark Lighter Fire drill Bow drill Hand drill Pump drill Fire piston Fire plough Fire-saw Fire striker Flint
Modern starters	Blowtorch Ferrocerium Lighter Match Black Electric
Other equipment	Char cloth Chuckmuck Feather stick Fire pan Fire pit Fire ring Matchbook Matchbox Punk Tinderbox Torch
Related articles	Arson Control of fire by early humans Firem'n Chit Native American use of fire in ecosystems Outdoor cooking Pyrolysis Pyromania Survival skills