SATA
![]() |
![]() | |
![]() From top to bottom, SATA Certification Logo, SATA cable, and two first-generation (1.5 Gbit/s) SATA data connectors on a motherboard. | |
Year created | 2003 |
---|---|
Supersedes | Parallel ATA (PATA) |
Speed | 1.5, 3.0, 6.0 Gbit/s |
Style | Serial |
Hotplugging interface | Yes[1] |
External interface | Yes (eSATA) |
Website | sata-io |
Serial ATA (SATA or Serial Advanced Technology Attachment) is a computer bus interface for connecting host bus adapters to mass storage devices such as hard disk drives and optical drives. Serial ATA was designed to replace the older ATA (AT Attachment) standard (also known as EIDE), offering several advantages over the older parallel ATA (PATA) interface: reduced cable-bulk and cost (7 conductors versus 40), native hot swapping, faster data transfer through higher signalling rates, and more efficient transfer through an (optional) I/O queuing protocol.
SATA host-adapters and devices communicate via a high-speed serial cable over two pairs of conductors. In contrast, parallel ATA (the redesignation for the legacy ATA specifications) used a 16-bit wide data bus with many additional support and control signals, all operating at much lower frequency. To ensure backward compatibility with legacy ATA software and applications, SATA uses the same basic ATA and ATAPI command-set as legacy ATA devices.
As of 2009[update], SATA has replaced parallel ATA in most shipping consumer desktop and laptop computers, and is expected to eventually replace PATA in embedded applications where space and cost are important factors. SATA’s market share in the desktop PC market was 99% in 2008.[2] PATA remains widely used in industrial and embedded applications that use CompactFlash storage, though even here, the next CFast storage standard will be based on SATA.[3][4]
Specification bodies
Serial ATA industry compatibility specifications originate from The Serial ATA International Organization (aka. SATA-IO, serialata.org). The SATA-IO group collaboratively creates, reviews, ratifies, and publishes the interoperability specifications, the test cases, and plug-fests. As with many other industry compatibility standards, the SATA content ownership is transferred to other industry bodies: primarily the INCITS T13subcommittee ATA, the INCITS T10 subcommittee (SCSI); a subgroup of T10 responsible for SAS. The complete specification from SATA-IO.[5] The remainder of this article will try to use the terminology and specifications of SATA-IO.
Features
Hotplug
The Serial ATA Spec includes logic for SATA device hotplugging. Devices and motherboards that meet the interoperability spec are capable of hot plugging.
Advanced Host Controller Interface
As their standard interface, SATA controllers use the AHCI (Advanced Host Controller Interface), allowing advanced features of SATA such as hotplug and native command queuing (NCQ). If AHCI is not enabled by the motherboard and chipset, SATA controllers typically operate in "IDE emulation" mode, which does not allow features of devices to be accessed if the ATA/IDE standard does not support them.
Windows device drivers that are labeled as SATA are often running in IDE emulation mode unless they explicitly state that they are AHCI mode, in RAID mode, or a mode provided by a proprietary driver and command set that was designed to allow access to SATA's advanced features before AHCI became popular. Modern versions of Microsoft Windows, FreeBSD, Linux with version 2.6.19 onward,[6] as well as Solaris and OpenSolaris include support for AHCI, but older OSes such as Windows XP do not. Even in those instances a proprietary driver may have been created for a specific chipset, such as Intel's.[7]
Revisions
SATA revision 1.0 (SATA 1.5 Gbit/s)
First-generation SATA interfaces, now known as SATA 1.5 Gbit/s, communicate at a rate of 1.5 Gbit/s. Taking 8b/10b encoding overhead into account, they have an actual uncoded transfer rate of 1.2 Gbit/s (150 MB/s). The theoretical burst throughput of SATA 1.5 Gbit/s is similar to that of PATA/133, but newer SATA devices offer enhancements such as NCQ, which improve performance in a multitasking environment.
During the initial period after SATA 1.5 Gbit/s finalization, adapter and drive manufacturers used a "bridge chip" to convert existing PATA designs for use with the SATA interface.[citation needed] Bridged drives have a SATA connector, may include either or both kinds of power connectors, and, in general, perform identically to their PATA equivalents. Most lack support for some SATA-specific features such as NCQ. Native SATA products quickly eclipsed bridged products with the introduction of the second generation of SATA drives.[citation needed]
As of April 2010 mechanical hard disk drives can transfer data at up to 157 MB/s,[8] which is beyond the capabilities of the older PATA/133 specification and also exceeds a SATA 1.5 Gbit/s link.
SATA revision 2.0 (SATA 3 Gbit/s)
Second generation SATA interfaces running at 3.0 Gbit/s are shipping in high volume as of 2010[update], and prevalent in all[citation needed] SATA disk drives and the majority of PC and server chipsets. With a native transfer rate of 3.0 Gbit/s, and taking 8b/10b encoding into account, the maximum uncoded transfer rate is 2.4 Gbit/s (300 MB/s). The theoretical burst throughput of SATA 3.0 Gbit/s is roughly double that of PATA/133. In addition, SATA devices offer enhancements such as native command queuing that improve performance in a multitasking environment.
All SATA data cables meeting the SATA spec are rated for 3.0 Gbit/s and will handle current mechanical drives without any loss of sustained and burst data transfer performance. However, high-performance flash drives are approaching SATA 3 Gbit/s transfer rate, and this is being addressed with the SATA 6 Gbit/s interoperability standard.
SATA revision 3.0 (SATA 6 Gbit/s)
Serial ATA International Organization presented the draft specification of SATA 6 Gbit/s physical layer in July 2008,[9] and ratified its physical layer specification on August 18, 2008.[10] The full 3.0 standard was released on May 27, 2009.[11] It provides peak throughput of about 600 MB/s (Megabytes per second) including the protocol overhead (10b/8b coding with 8 bits to one byte). While even the fastest conventional hard disk drives can barely saturate the original SATA 1.5 Gbit/s bandwidth, Solid-State Drives have already saturated SATA 3 Gbit/s with 285/275 MB/s max read/write speed and 250 MB/s sustained with the Sandforce 1200 and 1500 controller. However SandForce SSD controllers scheduled for release in 2011 have delivered 500 MB/s read/write rates,[12] and ten channels of fast flash can reach well over 500 MB/s with new ONFI drives – a move from SATA 3 Gbit/s to SATA 6 Gbit/s allows such devices to work at their full speed. Full performance from Crucial's C300 SSD similarly require SATA 3.0. As for standard hard disks, the reads from their built-in DRAM cache will end up faster across the new interface.[13] SATA 6 Gbit/s hard drives and motherboards are now shipping from several suppliers. Intel's current Sandybridge platform offers 6 Gbit/s SATA ports as standard.
The new specification contains the following changes:
- 6 Gbit/s for scalable performance when used with SSDs
- Continued compatibility with SAS, including SAS 6 Gbit/s. "A SAS domain may support attachment to and control of unmodified SATA devices connected directly into the SAS domain using the Serial ATA Tunneled Protocol (STP)" from the SATA_Revision_3_0_Gold specification.
- Isochronous Native Command Queuing (NCQ) streaming command to enable isochronous quality of service data transfers for streaming digital content applications.
- An NCQ Management feature that helps optimize performance by enabling host processing and management of outstanding NCQ commands.
- Improved power management capabilities.
- A small low insertion force (LIF) connector for more compact 1.8-inch storage devices.
- A connector designed to accommodate 7 mm optical disk drives for thinner and lighter notebooks.
- Alignment with the INCITS ATA8-ACS standard.
In general, the enhancements are aimed at improving quality of service for video streaming and high-priority interrupts. In addition, the standard continues to support distances up to a meter. The new speeds may require higher power consumption for supporting chips, factors that new process technologies and power management techniques are expected to mitigate. The new specification can use existing SATA cables and connectors, although some OEMs are expected to upgrade host connectors for the higher speeds.[14] Also, the new standard is backwards compatible with SATA 3 Gbit/s.[15]
Terminology
The name SATA II has become synonymous with the 3 Gbit/s standard. In order to provide the industry with consistent terminology, the SATA-IO has compiled a set of marketing guidelines for the third revision of the specification.
- The SATA 6 Gbit/s specification should be called Serial ATA International Organization: Serial ATA Revision 3.0.
- The technology itself is to be referred to as SATA 6 Gb/s.
- A product using this standard should be called the SATA 6 Gb/s [product name].
Using the terms SATA III or SATA 3.0 to refer to a SATA 6 Gbit/s product is unclear and not preferred. SATA-IO has provided a guideline to foster consistent marketing terminology across the industry.[16]
Cables, connectors, and ports
Connectors and cables present the most visible differences between SATA and parallel ATA drives. Unlike PATA, the same connectors are used on 3.5-inch (89 mm) SATA hard disks for desktop and server computers and 2.5-inch (64 mm) disks for portable or small computers; this allows 2.5-inch (64 mm) drives to be used in desktop computers with only a mounting bracket and no wiring adapter. Smaller disks may use the mini-SATA spec, suitable for small-form-factor Serial ATA drives and mini SSDs.[17]
There is a special connector (eSATA) specified for external devices, and an optionally implemented provision for clips to hold internal connectors firmly in place. SATA drives may be plugged into SAS controllers and communicate on the same physical cable as native SAS disks, but SATA controllers cannot handle SAS disks.
There are female SATA ports (on motherboards for example) for use with SATA data cable with locks or clips, thus reducing the chance of accidentally unplugging while the machine is turned on—As do SATA power/data connectors on optical and high-density devices. Moreover, some SATA cables have orthogonally positioned heads in the shape of an 'L' which in effect ease the connection of devices to circuit boards.
Data connector
Pin # | Function |
---|---|
1 | Ground |
2 | A+ (transmit) |
3 | A− (transmit) |
4 | Ground |
5 | B− (receive) |
6 | B+ (receive) |
7 | Ground |
![]() | |
A 7-pin Serial ATA right-angle data cable. |
The SATA standard defines a data cable with seven conductors (3 grounds and 4 active data lines in two pairs) and 8 mm wide wafer connectors on each end. SATA cables can have lengths up to 1 metre (3.3 ft), and connect one motherboard socket to one hard drive. PATA ribbon cables, in comparison, connect one motherboard socket to one or two hard drives, carry either 40 or 80 wires, and are limited to 45 centimetres (18 in) in length by the PATA specification (however, cables up to 90 centimetres (35 in) are readily available). Thus, SATA connectors and cables are easier to fit in closed spaces, and reduce obstructions to air cooling. They are more susceptible to accidental unplugging and breakage than PATA, but cables can be purchased that have a locking feature, whereby a small (usually metal) spring holds the plug in the socket.
One of the problems associated with the transmission of data at high speed over electrical connections is described as noise, which is due to electrical coupling between data circuits and other circuits. As a result, the data circuits can both affect other circuits, and be affected by them. Designers use a number of techniques to reduce the undesirable effects of such unintentional coupling. One such technique used in SATA links is differential signaling. This is an enhancement over PATA, which uses single-ended signaling. Some PATA cables use 80 wires, where only 40 wires carry signals.
Power connectors
Standard connector
Pin # | Mating | Function | |
---|---|---|---|
— | Coding notch | ||
1 | 3rd | 3.3 V | |
2 | 3rd | ||
3 | 2nd | ||
4 | 1st | Ground | |
5 | 2nd | ||
6 | 2nd | ||
7 | 2nd | 5 V | |
8 | 3rd | ||
9 | 3rd | ||
10 | 2nd | Ground | |
11 | 3rd | Staggered spinup/activity (in supporting drives) | |
12 | 1st | Ground | |
13 | 2nd | 12 V | |
14 | 3rd | ||
15 | 3rd | ||
![]() | |||
A 15-pin Serial ATA power receptacle. This connector does not provide the extended pins 4 and 12 needed for hot-plugging.[18] |
The SATA standard specifies a power connector that differs from the decades-old four-pin Molex connector found on pre-SATA devices. Like the data cable, it is wafer-based, but its wider 15-pin shape prevents accidental mis-identification and forced insertion of the wrong connector type. Native SATA devices favor the SATA power-connector, although some early SATA drives retained older 4-pin Molex in addition to the SATA power connector.
SATA features more pins than the traditional connector for several reasons:
- A third voltage is supplied, 3.3 V, in addition to the traditional 5 V and 12 V.
- Each voltage is transmitted through three pins grouped together, because the small contacts by themselves cannot supply sufficient current for some devices. (Each pin should be able to carry 1.5 A.)
- Five pins grouped together provide ground.
- For each of the three voltages, one of the three pins serves for hotplugging. The ground pins and power pins 3, 7, and 13 are longer on the plug (located on the SATA device) so they will connect first. A special hot-plug receptacle (on the cable or a backplane) can connect ground pins 4 and 12 first.
- Pin 11 can function for staggered spinup, activity indication, or nothing. Staggered spinup is used to prevent many drives from spinning up simultaneously, as this may draw too much power. Activity is an indication of whether the drive is busy, and is intended to give feedback to the user through an LED.
Adapters are available that convert a 4-pin Molex connector to a SATA power connector. Generally, because the power lines on 4-pin Molex connectors do not provide 3.3 V power, these adapters provide only 5 V and 12 V power on the SATA end and leave the 3.3 V lines unconnected. This precludes the use of such adapters with drives that require 3.3 V power. Because of this, drive manufacturers have largely not used the 3.3 V power lines. There also exist some 4-pin Molex to SATA power adapters which include electronics to provide 3.3 V power.
Slimline connector
SATA 2.6 first defined the slimline connector, intended for smaller form-factors; e.g., notebook optical drives.
Pin # | Function | |
---|---|---|
1 | Device presence | |
2 | 5 V | |
3 | ||
4 | Manufacturing diagnostic | |
5 | Ground | |
6 |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/4/4f/SATA_Slimline_Powercable.jpg/200px-SATA_Slimline_Powercable.jpg)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/c/c7/SATA_connector_Slimline_CD-ROM.jpg/200px-SATA_connector_Slimline_CD-ROM.jpg)
Micro connector
The micro connector originated with SATA 2.6. It is intended for 1.8-inch (46 mm) hard drives. There is also a micro data connector, which is similar to the standard data connector, but is slightly thinner.
Pin # | Function | |
---|---|---|
1 | 3.3 V | |
2 | ||
3 | Ground | |
4 | ||
5 | 5 V | |
6 | ||
7 | Reserved | |
8 | Vendor specific | |
9 |
eSATA
![](http://upload.wikimedia.org/wikipedia/en/thumb/0/09/ESATA_Logo.svg/220px-ESATA_Logo.svg.png)
![](http://upload.wikimedia.org/wikipedia/commons/thumb/9/90/SATA2_und_eSATA-Stecker.jpg/220px-SATA2_und_eSATA-Stecker.jpg)
Standardized in 2004, eSATA (e=external) provides a variant of SATA meant for external connectivity. It has revised electrical requirements in addition to incompatible cables and connectors:
- Minimum transmit potential increased: Range is 500–600 mV instead of 400–600 mV.
- Minimum receive potential decreased: Range is 240–600 mV instead of 325–600 mV.
- Identical protocol and logical signaling (link/transport-layer and above), allowing native SATA devices to be deployed in external enclosures with minimal modification
- Maximum cable length of 2 metres (6.6 ft) (USB and FireWire allow longer distances.)
- The external cable connector equates to a shielded version of the connector specified in SATA 1.0a with these basic differences:
- The external connector has no "L"-shaped key, and the guide features are vertically offset and reduced in size. This prevents the use of unshielded internal cables in external applications and vice-versa.
- To prevent ESD damage, the design increased insertion depth from 5 mm to 6.6 mm and the contacts are mounted farther back in both the receptacle and plug.
- To provide EMI protection and meet FCC and CE emission requirements, the cable has an extra layer of shielding, and the connectors have metal contact-points.
- The connector shield has springs as retention features built in on both the top and bottom surfaces.
- The external connector and cable have a design-life of over five thousand insertions and removals, whereas the internal connector is specified to withstand only fifty.
Aimed at the consumer market, eSATA enters an external storage market already served by the USB and FireWire interfaces. Most external hard-disk-drive cases with FireWire or USB interfaces use either PATA or SATA drives and "bridges" to translate between the drives' interfaces and the enclosures' external ports, and this bridging incurs some inefficiency. Some single disks can transfer 157 MB/s during real use,[8] about four times the maximum transfer rate of USB 2.0 or FireWire 400 (IEEE 1394a) and almost twice as fast as the maximum transfer rate of FireWire 800, though the S3200 FireWire 1394b spec reaches ~800 MB/s (3.2 Gbit/s). Finally, some low-level drive features, such as S.M.A.R.T., may not operate through some USB [2] or FireWire or USB+FireWire bridges. eSATA does not suffer from these issues provided that the controller manufacturer (and its drivers) presents eSATA drives as ATA devices, rather than as "SCSI" devices (as has been common with Silicon Image, JMicron, and NVIDIA nForce drivers for Windows Vista); In those cases, even SATA drives will not have low-level features accessible. USB 3.0's 4.8 Gbit/s and Firewire's future 6.4 Gb/s (768 MB/s) will be faster than eSATA I, but the eSATA version of SATA 6G will operate at 6.0 Gb/s (the term SATA III is being eschewed by the SATA-IO to avoid confusion with SATA II 3.0 Gbit/s, which was colloquially referred to as "SATA 3G" [bps] or "SATA 300" [MB/s] since 1.5 Gbit/s SATA I and 1.5 Gbit/s SATA II were referred to as both "SATA 1.5G" [b/s] or "SATA 150" [MB/s]). Therefore, they will operate with negligible differences between them.[19]
eSATA can be differentiated from USB 2.0 and FireWire external storage for several reasons. As of early 2008, the vast majority of mass-market computers have USB ports and many computers and consumer electronic appliances have FireWire ports, but few devices have external SATA connectors. For small form-factor devices (such as external 2.5-inch (64 mm) disks), a PC-hosted USB or FireWire link supplies sufficient power to operate the device. Where a PC-hosted port is concerned, eSATA connectors cannot supply power, and would therefore be more cumbersome to use. Note that this problem has been solved by the introduction of eSATAp.[20] Some e-sata ports double as eSATA/USB.
Owners of desktop computers that lack a built-in eSATA interface can upgrade them with the installation of an eSATA host bus adapter (HBA), while notebooks can be upgraded with Cardbus[21] or ExpressCard[22] versions of an eSATA HBA. With passive adapters, the maximum cable length is reduced to 1 metre (3.3 ft) due to the absence of compliant eSATA signal-levels.
eSATAp
eSATAp is also known as Power over eSATA or eSATA/USB Combo. eSATAp port combines the strength of both eSATA (high speed) and USB (compatibility) into a single port. eSATAp devices are now capable of being self powered. On a desktop workstation, eSATAp port can supply 12 V to power up a 3.5" hard disk drive (HDD) or a 5.25" DVD-RW without needing separate power source as compared to eSATA and USB 2.0. On a notebook eSATAp port can supply 5 V to power up a 2.5" HDD/SSD as compared to eSATA. Many notebooks are now equipped with this combo port.
eSATAp can be implemented in all machines with a spare SATA port. These machines include PC notebooks, desktops, Apple Mac Pro, and Linux or Unix servers. This makes eSATAp an easy, economical, cross platform solution for external storage.
Pre-standard implementations
- Prior to the final eSATA 3 Gbit/s specification, a number of products existed designed for external connections of SATA drives. Some of these use the internal SATA connector or even connectors designed for other interface specifications, such as FireWire. These products are not eSATA compliant. The final eSATA specification features a specific connector designed for rough handling, similar to the regular SATA connector, but with reinforcements in both the male and female sides, inspired by the USB connector. eSATA resists inadvertent unplugging, and can withstand yanking or wiggling, which could break a male SATA connector (the hard-drive or host adapter, usually fitted inside the computer). With an eSATA connector, considerably more force is needed to damage the connector, and if it does break it is likely to be the female side, on the cable itself, which is relatively easy to replace.[citation needed]
- Prior to the final eSATA 6 Gbit/s specification many add-on cards and some motherboards advertise eSATA 6 Gbit/s support because they have 6 Gbit/s SATA 3.0 controllers for internal-only solutions. Those implementations are non standard and eSATA 6 Gbit/s requirements will be ratified in the upcoming SATA 3.1 specification.[23] These products might not be eSATA 6 Gbit/s compliant.
mSATA
Mini-SATA not to be confused with the micro connector was announced by the Serial ATA International Organization, September 21, 2009.[24]
Applications include netbooks and other devices that require a smaller Solid-state drive. The connector resembles a miniPCIe (mini PCI Epxress) card interface.[25]
Protocol
The SATA specification defines three distinct protocol layers: physical, link, and transport.
Physical layer
The physical layer defines SATA's electrical and physical characteristics (such as cable dimensions and parasitics, driver voltage level and receiver operating range), as well as the physical coding subsystem (bit-level encoding, device detection on the wire, and link initialization).
Physical transmission uses differential signaling. The SATA PHY contains a transmit pair and receive pair. When the SATA-link is not in use (example: no device attached), the transmitter allows the transmit pins to float to their common-mode voltage level. When the SATA-link is either active or in the link-initialization phase, the transmitter drives the transmit pins at the specified differential voltage (1.5v in SATA/I.)
SATA physical coding uses a line encoding system known as 8b/10b encoding. This scheme serves multiple functions required to sustain a differential serial link. First, the stream contains necessary synchronization information that allows for SATA host/drive to extract clocking. The 8b/10b encoded sequence embeds periodic edge transitions to allow the receiver to achieve bit-alignment without the use of a separately transmitted reference clock waveform. The sequence also maintains a neutral (DC-balanced) bitstream, which allows the transmit drivers and receiver inputs to be AC-coupled.
Also, Serial/ATA uses some of the of special characters defined in 8b/10b. In particular, the PHY layer uses the comma (K28.5) character to maintain symbol-alignment. A specific 4-symbol sequence, the ALIGN primitive, is used for clock rate-matching between the two devices on the link. Other special symbols communicate flow control information produced and consumed in the higher layers (link and transport.)
Separate point-to-point AC-coupled LVDS links are used for physical transmission between host and drive.
The PHY layer is responsible for detecting the other SATA/device on a cable, and link initialization. During the link-initialization process, the PHY is responsible for locally generating special out-of-band signals by switching the transmitter between electrical-idle and specific 10b-characters in a defined pattern, negotiating a mutually supported signalling rate (1.5, 3.0, or 6.0 Gbps), and finally synchronizing to the far-end device's PHY-layer data stream. During this time, no data is sent from the link-layer.
Once link-initialization has completed, the link-layer takes over data-transmission, with the PHY providing only the 8b/10b conversion before bit transmission.
Link layer
After the PHY-layer has established a link, the link layer is responsible for transmission and reception of FISs over the SATA link. FISs are packets containing control information or payload data. Each packet contains a header (identifying its type), and payload whose contents are dependent on the type. The link layer also manages flow control between over the link.
Topology
![](http://upload.wikimedia.org/wikipedia/commons/thumb/a/af/Sata_host_expansor_en.gif/220px-Sata_host_expansor_en.gif)
SATA uses a point-to-point architecture. The physical connection between a controller and a storage device is not shared among other controllers and storage devices. SATA defines multipliers, which allows a single SATA controller to drive multiple storage devices. The multiplier performs the function of a hub; the controller and each storage device is connected to the hub.
Modern[update] PC systems have SATA controllers built into the motherboard, typically featuring 2 to 6 ports. Additional ports can be installed through add-in SATA host adapters (available in variety of bus-interfaces: USB, PCI, PCI-e.)
Backward and forward compatibility
SATA and PATA
At the device level, SATA and PATA (Parallel AT Attachment) devices remain completely incompatible—they cannot be interconnected. At the application level, SATA devices can be specified to look and act like PATA devices.[26] Many motherboards offer a "legacy mode" option, which makes SATA drives appear to the OS, like PATA drives on a standard controller. This eases OS installation by not requiring a specific driver to be loaded during setup but sacrifices support for some features of SATA and, in general, disables some of the boards' PATA or SATA ports, since the standard PATA controller interface supports only 4 drives. (Often which ports are disabled is configurable.)
The common heritage of the ATA command set has enabled the proliferation of low-cost PATA to SATA bridge-chips. Bridge-chips were widely used on PATA drives (before the completion of native SATA drives) as well as standalone "dongles." When attached to a PATA drive, a device-side dongle allows the PATA drive to function as a SATA drive. Host-side dongles allow a motherboard PATA port to function as a SATA host port.
The market has produced powered enclosures for both PATA and SATA drives that interface to the PC through USB, Firewire or eSATA, with the restrictions noted above. PCI cards with a SATA connector exist that allow SATA drives to connect to legacy systems without SATA connectors.
SATA 1.5 Gbit/s, SATA 3 Gbit/s and SATA 6 Gbit/s
The designers of SATA aimed for backward and forward compatibility with future revisions of the SATA standard.[citation needed]
According to the hard drive manufacturer Maxtor, motherboard host controllers using the VIA and SIS chipsets VT8237, VT8237R, VT6420, VT6421L, SIS760, SIS964 found on the ECS 755-A2 manufactured in 2003, do not support SATA 3 Gbit/s drives. Additionally, these host controllers do not support SATA 3 Gbit/s optical disc drives. Users with a SATA 1.5 Gbit/s motherboard with one of the listed chipsets should either buy an ordinary SATA 1.5 Gbit/s hard disk, buy a SATA 3 Gbit/s hard disk switchable to 1.5 Gbit/s, or buy a PCI or PCI-E card to add full SATA 3 Gbit/s capability and compatibility.
To address interoperability problems many manufacturers allow to switch drives to the SATA1 mode. For example, Seagate/Maxtor has added a user-accessible jumper-switch known as the Force 150, to switch between 1.5 Gbit/s and 3 Gbit/s operation. Western Digital uses a jumper setting called OPT1 Enabled to force 1.5 Gbit/s data transfer speed (OPT1 is used by putting the jumper on pins 5 & 6). Samsung drives can be switched to 1.5 Gbit/s mode by using software downloadable from the manufacturer website. This needs a SATA2 controller to use temporarily while programming the drive.
The Force 150 switch is also useful when placing SATA 300 hard drives on SATA controllers on PCI cards, since many of these controllers (such as the Silicon Images chips) will run at SATA300 even though the PCI bus cannot even reach SATA150 speeds. This can cause data corruption in operating systems that do not specifically test for this condition and limit the disk transfer speed.
Comparison to other interfaces
SATA and SCSI
SCSI uses a more complex bus than SATA, usually resulting in higher manufacturing-costs. SCSI buses also allow connection of several drives on one shared channel, whereas SATA allows one drive per channel, unless using a port multiplier.
SATA 3 Gbit/s offers a maximum bandwidth of 300 MB/s per device compared to SCSI with a maximum of 320 MB/s in total for all devices on a bus.[27] Also, SCSI drives provide greater sustained throughput than multiple SATA drives connected via a simple (i. e. command-based) port multiplier because of disconnect-reconnect and aggregating performance.[28] In general, SATA devices link compatibly to SAS enclosures and adapters, whereas SCSI devices cannot be directly connected to a SATA bus.
SCSI, SAS, and fibre-channel (FC) drives are typically more expensive so they are traditionally used in servers and disk arrays where the added cost is justifiable. Inexpensive ATA and SATA drives evolved in the home-computer market, hence there is a view that they are less reliable. As those two worlds overlapped, the subject of reliability became somewhat controversial. Note that, in general, the failure rate of a disk drive is related to the quality of its heads, platters and supporting manufacturing processes, not to its interface.
Serial ATA in the business market has increased from 21.6% in 2006 to 27.6% in 2008. http://www.serialata.org/documents/SATA-Rev-30-Presentation.pdf
Comparison to other buses
Name | Raw bandwidth (Mbit/s) | Transfer speed (MByte/s) | Max. cable length (m) | Power provided | Devices per Channel |
---|---|---|---|---|---|
eSATA | 3,000 | 300 | 2 with eSATA HBA (1 with passive adapter) | No | 1 (15 with port multiplier) |
eSATAp | 5 V/12 V[29] | ||||
SATA revision 3.0 | 6,000 | 600[30] | 1 | No | |
SATA revision 2.0 | 3,000 | 300 | |||
SATA revision 1.0 | 1,500 | 150[31] | 1 per line | ||
PATA 133 | 1,064 | 133.5 | 0.46 (18 in) | No | 2 |
SAS 600 | 6,000 | 600 | 10 | No | 1 (>65k with expanders) |
SAS 300 | 3,000 | 300 | |||
SAS 150 | 1,500 | 150 | |||
FireWire 3200 | 3,144 | 393 | 100 (more with special cables) | 15 W, 12–25 V | 63 (with hub) |
FireWire 800 | 786 | 98.25 | 100[32] | ||
FireWire 400 | 393 | 49.13 | 4.5[32][33] | ||
USB 3.0* | 5,000 | 400[34] | 3[35] | 4.5 W, 5 V | 127 (with hub)[35] |
USB 2.0 | 480 | 60 | 5[36] | 2.5 W, 5 V | |
USB 1.0 | 12 | 1.5 | 3 | Yes | |
SCSI Ultra-640 | 5,120 | 640 | 12 | No | 15 (plus the HBA) |
SCSI Ultra-320 | 2,560 | 320 | |||
Fibre Channel over optic fibre |
10,520 | 2,000 | 2–50,000 | No | 126 (16,777,216 with switches) |
Fibre Channel over copper cable |
4,000 | 400 | 12 | ||
InfiniBand Quad Rate |
10,000 | 1,000 | 5 (copper)[37][38]
<10,000 (fiber) |
No | 1 with point to point Many with switched fabric |
Thunderbolt | 10,000 | 1,250 | 100 | 10 W | 7 |
- * USB 3.0 specification released to hardware vendors 17 November 2008.
Unlike PATA, both SATA and eSATA support hot-swapping by design. However, this feature requires proper support at the host, device (drive), and operating-system level. In general, all SATA devices (drives) support hot-swapping (due to the requirements on the device-side), also most SATA host adapters support this command.[1]
SCSI-3 devices with SCA-2 connectors are designed for hot-swapping. Many server and RAID systems provide hardware support for transparent hot-swapping. The designers of the SCSI standard prior to SCA-2 connectors did not target hot-swapping, but, in practice, most RAID implementations support hot-swapping of hard disks.
Serial Attached SCSI (SAS) is designed for hot-swapping.
Development tools
In development of new products, or when troubleshooting the Serial ATA bus, examination of hardware signals can be very important to find problems. Logic analyzers and bus analyzers are tools which collect, analyze, decode, store signals so people can view the high-speed waveforms at their leisure.
See also
- libATA
- Advanced Host Controller Interface (AHCI)
- AT Attachment (ATA)
- FATA
- Native Command Queuing (NCQ)
- TRIM (SSD command)
- List of device bandwidths
Notes and references
- ^ a b "Software status — ata Wiki". Ata.wiki.kernel.org. 2008-08-17. Retrieved 2010-01-26.
- ^ http://www.serialata.org/documents/SATA-Rev-30-Presentation.pdf
- ^ Donald Melanson (25 February 2008). "CFast CompactFlash cards now said to be coming in "18 to 24 months"". Engadget. Retrieved 19 March 2009.
- ^ "Pretec release CFast card with SATA interface". DPReview. 8 January 2009. Retrieved 19 March 2009.
- ^ "ATA-ATAPI.COM Serial ATA (SATA)". Retrieved 29 January 2009.
- ^ "Serial ATA (SATA) Linux hardware/driver status report". Linux-ata.org. Retrieved 2010-01-26.
- ^ http://www.intel.com/support/chipsets/imst/sb/CS-020825.htm
- ^ a b Patrick Schmid and Achim Roos (2010-04-06). "VelociRaptor Returns: 6Gb/s, 600GB, And 10,000 RPM". tomshardware.com. Retrieved 2010-06-26.
- ^ "New SATA Spec Will Double Data Transfer Rates to 6 Gbit/s" (PDF) (Press release). SATA-IO. 18 August 2008. Retrieved 13 July 2009.
- ^ "SATA Revision 3.0". SATA-IO. 27 May 2009. Retrieved 4 December 2009.
- ^ "SATA-IO Releases SATA Revision 3.0 Specification" (PDF) (Press release). Serial ATA International Organization. May 27, 2009. Retrieved 3 July 2009.
- ^ Shimpi, Anand (2011-01-05). "OCZ Vertex Pro 3 Demo: World's First SandForce SF-2000". Anandtech. Retrieved 2011-01-07.
- ^ "IDF Fall 2008 coverage". The Inquirer. Retrieved 2010-01-26.
- ^ "EETimes news report". Eetimes.com. Retrieved 2010-01-26.
- ^ "SATA-IO Specifications and Naming Conventions". Sata-io.org. Retrieved 2010-01-26.
- ^ http://www.serialata.org/developers/naming_guidelines.asp
- ^ "Get ready for mini-SATA". The Tech Report. 2009-09-21. Retrieved 2010-01-26.
- ^ https://raid.wiki.kernel.org/index.php/Hardware_issues#Hotplug_support_by_SATA.2FSAS_cables
- ^ "Questions about the indicators of health/performance (in percent)". HDDlife. Retrieved 29 August 2007.
- ^ "External Serial ATA" (PDF). Silicon Image, Inc. Retrieved 8 August 2009.
- ^ "CardBus SATA adapter". Addonics.com. Retrieved 2010-01-26.
- ^ "ExpressCard SATA adapter". Addonics.com. Retrieved 2010-01-26.
- ^ [1]
- ^ "mSATA Press Release" (PDF). Retrieved 11 March 2011.
- ^ "Intel 310 SSD" (PDF). Intel 310 SSD. Intel. Retrieved 11 March 2011.
- ^ "A comparison with Ultra ATA Technology" (PDF). SATA-IO. Retrieved 12 July 2007.
- ^ Ultra-640 is specified but devices do not exist
- ^ FIS-based switching is comparable to SCSI's tagged command queueing
- ^ "eSATAp Application". Delock.de. Retrieved 2010-01-26.
- ^ http://www.sata-io.org/documents/SATA-6Gbs-Fast-Just-Got-Faster.pdf
- ^ http://www.sata-io.org/documents/SATA-IO-English-Brochure-May-2009.pdf
- ^ a b "FireWire Developer Note: FireWire Concepts". Apple Developer Connection. Retrieved 13 July 2009.
- ^ 16 cables can be daisy chained up to 72 m
- ^ Universal Serial Bus Specification Revision 3.0. 12 November 2008. p. 69 (4-17). Retrieved 14 April 2011.
- ^ a b Frenzel, Louis E. (September 25, 2008). "USB 3.0 Protocol Analyzer Jumpstarts 4.8-Gbit/s I/O Projects". Electronic Design. Retrieved 3 July 2009.
- ^ USB hubs can be daisy chained up to 25 m
- ^ Minich, Makia (25 June 2007). "Infiniband Based Cable Comparison" (PDF). Retrieved 11 February 2008.[dead link]
- ^ Feldman, Michael (17 July 2007). "Optical Cables Light Up InfiniBand". HPCwire. Tabor Publications & Events. p. 1. Retrieved 11 February 2008.
External links
![](http://upload.wikimedia.org/wikipedia/en/thumb/4/4a/Commons-logo.svg/30px-Commons-logo.svg.png)
- Serial ATA International Organization (SATA-IO)
- EETimes Serial ATA and the evolution in data storage technology, Mohamed A. Salem
- "SATA-1" specification, as a zipped pdf; Serial ATA: High Speed Serialized AT Attachment, Revision 1.0a, 7-January-2003.
- Errata and Engineering Change Notices to above "SATA-1" specification, as a zip of pdfs
- Dispelling the Confusion: SATA II does not mean 3 Gbit/s
- Template:PDFlink
- SATA motherboard connector pinout
- AHCI/RAID Intel Matrix Storage Technology: Unattended installation instructions under Windows XP
- Intel Matrix Storage Manager: How do I install an operating system on single serial ATA hard drive?
- Serial ATA Connector Schematic and Pinout
- Serial ATA server and storage use cases
- How to Install and Troubleshoot SATA Hard Drives
- Serial ATA and the 7 Deadly Sins of Parallel ATA
- Everything You Need to Know About Serial ATA
- Barracuda XT - the first SATA 6Gb/s HDD
- Mini-FAQ on SATA II (specifications/performance/compatibility)