Photovoltaics

Photovoltaic 'tree' in Styria, Austria

Photovoltaics (PV) is the field of technology and research related to the application of solar cells for energy by converting sunlight directly into electricity. Due to the growing demand for clean sources of energy, the manufacture of solar cells and photovoltaic arrays has expanded dramatically in recent years.

Photovoltaic production has been doubling every two years, increasing by an average of 48 percent each year since 2002, making it the world’s fastest-growing energy technology. At the end of 2007, according to preliminary data, cumulative global production was 12,400 megawatts. Roughly 90% of this generating capacity consists of grid-tied electrical systems. Such installations may be ground-mounted (and sometimes integrated with farming and grazing) or built into the roof or walls of a building, known as Building Integrated Photovoltaic or BIPV for short.

Financial incentives, such as preferential feed-in tariffs for solar-generated electricity, and net metering, have supported solar PV installations in many countries including Germany, Japan, and the United States.

Overview

Photovoltaic cells produce electricity directly from sunlight

Average solar irradiance, watts per square metre. Note that this is for a horizontal surface, whereas solar panels are normally propped up at an angle and receive more energy per unit area. The small black dots show the area of solar panels needed to generate all of the worlds energy using 8% eff. PVs.

Map of solar electricity potential in Europe

Photovoltaics are best known as a method for generating solar power by using solar cells packaged in photovoltaic modules, often electrically connected in multiples as solar photovoltaic arrays to convert energy from the sun into electricity. To explain the photovoltaic solar panel more simply, photons from sunlight knock electrons into a higher state of energy, creating electricity. The term photovoltaic denotes the unbiased operating mode of a photodiode in which current through the device is entirely due to the transduced light energy. Virtually all photovoltaic devices are some type of photodiode.

Solar cells produce direct current electricity from light, which can be used to power equipment or to recharge a battery. The first practical application of photovoltaics was to power orbiting satellites and other spacecraft, but today the majority of photovoltaic modules are used for grid connected power generation. In this case an inverter is required to convert the DC to AC. There is a smaller market for off grid power for remote dwellings, roadside emergency telephones, remote sensing, and cathodic protection of pipelines.

Cells require protection from the environment and are packaged usually behind a glass sheet. When more power is required than a single cell can deliver, cells are electrically connected together to form photovoltaic modules, or solar panels. A single module is enough to power an emergency telephone, but for a house or a power plant the modules must be arranged in arrays. Although the selling price of modules is still too high to compete with grid electricity in most places, significant financial incentives in Japan and then Germany triggered a huge growth in demand, followed quickly by production.

Perhaps not unexpectedly, a significant market has emerged in urban or grid-proximate locations for solar-power-charged storage-battery based solutions. These are deployed as stand-by systems in energy deficient countries like India and as supplementary systems in developed markets. In a vast majority of situations such solutions make neither economic nor environmental sense, any green credentials being largely offset by the lead-acid storage systems typically deployed.

The EPIA/Greenpeace Advanced Scenario shows that by the year 2030, PV systems could be generating approximately 2,600 TWh of electricity around the world. This means that, assuming a serious commitment is made to energy efficiency, enough solar power would be produced globally in twenty-five years’ time to satisfy the electricity needs of almost 14% of the world’s population.

Current development

The most important issue with solar panels is capital cost (installation and materials). Newer alternatives to standard crystalline silicon modules including casting wafers instead of sawing, thin film (CdTe CIGS, amorphous Si, microcrystalline Si), concentrator modules, 'Sliver' cells, and continuous printing processes. Due to economies of scale solar panels get less costly as people use and buy more — as manufacturers increase production to meet demand, the cost and price is expected to drop in the years to come. By early 2006, the average cost per installed watt for a residential sized system was about USD 7.50 to USD 9.50, including panels, inverters, mounts, and electrical items. In 2006 investors began offering free solar panel installation in return for a 25 year contract, or Power Purchase Agreement, to purchase electricity at a fixed price, normally set at or below current electric rates. It is expected that by 2009 over 90% of commercial photovoltaics installed in the United States will be installed using a power purchase agreement. The current market leader in solar panel efficiency (measured by energy conversion ratio) is SunPower, a San Jose based company. Sunpower's cells have a conversion ratio of 23.4%, well above the market average of 12-18%. However, advances past this efficiency mark are being innovated by engineers at MIT and the California Institute of Technology, and efficiencies of 42% have been achieved at the University of Delaware.

Worldwide installed photovoltaic totals

See also: Deployment of solar power to energy grids

Template:Wikinews2 World solar photovoltaic (PV) market installations reached a record high of 2.8 gigawatts peak (GWp) in 2007.

The three leading countries (Germany, Japan and the USA) represent nearly 89% of the total worldwide PV installed capacity. On Wed 1 August 2007, word was published of construction of a production facility in China, which is projected to be one of the largest wafer factories in the world, with a peak capacity of around 1,500MW.

Germany was the fastest growing major PV market in the world during 2006 and 2007. In 2007, over 1.3 GWp of PV was installed. The German PV industry generates over 10,000 jobs in production, distribution and installation. By the end of 2006, nearly 88% of all solar PV installations in the EU were in grid-tied applications in Germany. The balance is off-grid (or stand alone) systems. Photovoltaic power capacity is measured as maximum power output under standardized test conditions (STC) in "Wp" (Watts peak). The actual power output at a particular point in time may be less than or greater than this standardized, or "rated," value, depending on geographical location, time of day, weather conditions, and other factors. Solar photovoltaic array capacity factors are typically under 25%, which is lower than many other industrial sources of electricity. Therefore the 2006 installed base peak output would have provided an average output of 1.2 GW (assuming 20% × 5,862 MWp). This represented 0.06 percent of global demand at the time.

Produced, Installed & Total Photovoltaic Peak Power Capacity (MWp) as of the end of 2007

Country or Region Report Nat. Int.	off grid Δ	on grid Δ	Installed 2007	off grid Σ	on grid Σ	Total 2007	Wp/capita Total	Module Price €/Wp	kW·h/kWp·yr Insolation	Feed-in Tariff EU¢/kW·h
Template:Country data World	127.9	2,130	2,258	662.3	7,178	7,841		2.5-11.2	0800-2902	0-59.3
Germany	35	1,100	1,135	35	3,827	3,862	46.8	4.0-5.3	1000-1300	51.8-56.8
Japan	1.562	208.8	210.4	90.15	1829	1919	15	2.96	1200-1600	Ended(2005)
United States	55	151.5	206.5	325	505.5	830.5	2.8	2.98	0900-2150	1.2-31.04(CA)
Spain ?	22	490	512	29.8	625.2	655	15.1	3.0-4.5	1600-2200	18.38-44.04
Italy	0.3	69.9	70.2	13.1	107.1	120.2	2.1	3.2-3.6	1400-2200	36.0-49.0
Australia	5.91	6.28	12.19	66.45	16.04	82.49	4.1	4.5-5.4	1450-2902	0-26.4(SA'08)
South Korea	0	42.87	42.87	5.943	71.66	77.60	1.6	3.50-3.84	1500-1600	56.5-59.3
France	0.993	30.31	31.30	22.55	52.68	75.23	1.2	3.2-5.1	1100-2000	30.0-55.0
Netherlands	0.582	1.023	1.605	5.3	48	53.3	3.3	3.3-4.5	1000-1200	1.21-9.7
Switzerland	0.2	6.3	6.5	3.6	32.6	36.2	4.9	3.18-3.30	1200-2000	9.53-50.8
Austria ?	0.055	2.061	2.116	3.224	24.48	27.70	3.4	3.6-4.3	1200-2000	>0
Canada	3.888	1.403	5.291	22.86	2.911	25.78	0.8	3.76	0900-1750	0-29.48(ON)
Mexico ?	0.869	0.15	1.019	20.45	0.3	20.75	0.2	5.44-6.42	1700-2600	None
United Kingdom	0.16	3.65	3.81	1.47	16.62	18.09	0.3	3.67-5.72	0900-1300	0-11.74(exprt)
Portugal ?	0.2	14.25	14.45	2.841	15.03	17.87	1.7		1600-2200
Norway	0.32	0.004	0.324	7.86	0.132	7.992	1.7	11.2	0800-0950	None
Sweden	0.271	1.121	1.392	4.566	1.676	6.242	0.7	3.24-7.02	0900-1050	None
Denmark	0.05	0.125	0.175	0.385	2.69	3.075	0.6	5.36-8.04	0900-1100	None
Israel	0.5	0	0.5	1.794	0.025	1.819	0.3	4.3	2200-2400	13.13-16.40
Country or Region Report Nat. Int.	off grid Δ	on grid Δ	Installed 2007	off grid Σ	on grid Σ	Total 2007	Wp/capita Total	Module Price €/Wp	kW·h/kWp·yr Insolation	Feed-in Tariff EU¢/kW·h

Notes: While National Report(s) may be cited as source(s) within an International Report, any contradictions in data are resolved by using only the most recent report's data. Exchange rates represent the 2006 annual average of daily rates (OECD Main Economic Indicators June 2007).
Module Price: Lowest:2.5 EUR/Wp (2.83 USD/Wp) in Germany 2003. Uncited insolation data is from maps dating 1991-1995.
PV Power (2007-June) IEA PVPS website.

Applications of PV

Main article: Photovoltaic system

PV power stations

Main article: Photovoltaic power station

Solar array at Nellis Air Force Base. These panels track the sun in one axis.

Several large photovoltaic power plants were completed in Spain during 2008: the Parque Fotovoltaico Olmedilla de Alarcon (60 MW), Parque Solar Merida/Don Alvaro (30 MW), Planta solar Fuente Álamo (26 MW), Planta fotovoltaica de Lucainena de las Torres (23.2 MW), Parque Fotovoltaico Abertura Solar (23.1 MW), Parque Solar Hoya de Los Vincentes (23 MW), the Solarpark Calveron (21 MW), and the Planta Solar La Magascona (20 MW).

The 14 MW Nellis Solar Power Plant is the largest solar photovoltaic system in North America, and is located within Nellis Air Force Base in Clark County, Nevada, on the northeast side of Las Vegas. The Nellis solar energy system will generate in excess of 25 million kilowatt-hours of electricity annually and supply more than 25 percent of the power used at the base.

World's largest photovoltaic (PV) power plants

Name	Country	DC Peak Power (MW)	Description	GW·h /year
Parque Fotovoltaico Olmedilla de Alarcon	Spain	60	Completed September 2008	85
Parque Solar Merida/Don Alvaro	Spain	30	Completed September 2008
Planta solar Fuente Álamo	Spain	26		44
Planta fotovoltaica de Lucainena de las Torres	Spain	23.2	Completed August 2008
Parque Fotovoltaico Abertura Solar	Spain	23.1		47
Parque Solar Hoya de Los Vincentes	Spain	23		41
Solarpark Calveron	Spain	21.2		40
Huerta Solar Almaraz	Spain	20	Completed September 2008
Planta solar fotovoltaico Calasparra	Spain	20
Planta Solar La Magascona	Spain	20		42
Beneixama photovoltaic power plant	Spain	20	Tenesol, Aleo and Solon solar modules with Q-Cells cells	30
SinAn photovoltaic power plant	South Korea	19.6	Asia's largest photovoltaic plant. Consists of 108,864 units of Conergy STM 180F solar modules.	27
Planta de energía solar Mahora	Spain	15	Completed September 2008
Nellis Solar Power Plant	USA	14	70,000 solar panels	30
Planta Solar de Salamanca	Spain	13.8	70,000 Kyocera panels	n.a.
Parque Solar Guadarranque	Spain	13.6		20
Lobosillo Solar Park	Spain	12.7	Chaori an YingLi modules	n.a.
Parque Solar Fotovoltaico Villafranca	Spain	12	High concentration PV technology
Erlasee Solar Park	Germany	12	1,408 Solon mover	14
Serpa solar power plant	Portugal	11	52,000 solar modules	20
Pocking Solar Park	Germany	10	57,912 solar modules	11.5

Topaz Solar Farm is a proposed 550 MW solar photovoltaic power plant which is to be built northwest of California Valley in the USA at a cost of over $1 billion. Built on 9.5 square miles (25 km²) of ranchland, the project would utilize thin-film PV panels designed and manufactured by OptiSolar in Hayward and Sacramento. The project would deliver approximately 1,100 gigawatt-hours (GW·h) annually of renewable energy. The project is expected to begin construction in 2010, begin power delivery in 2011, and be fully operational by 2013.

High Plains Ranch is a proposed 250 MW solar photovoltaic power plant which is to be built by SunPower in the Carrizo Plain, northwest of California Valley.

PV in buildings

Main article: Building-integrated photovoltaic

Photovoltaic solar panels on a house roof.

Building-integrated photovoltaics (BIPV) are increasingly incorporated into new domestic and industrial buildings as a principal or ancillary source of electrical power, and are one of the fastest growing segments of the photovoltaic industry. Typically, an array is incorporated into the roof or walls of a building, and roof tiles with integrated PV cells can now be purchased. Arrays can also be retrofitted into existing buildings; in this case they are usually fitted on top of the existing roof structure. Alternatively, an array can be located separately from the building but connected by cable to supply power for the building.

Where a building is at a considerable distance from the public electricity supply (or grid) - in remote or mountainous areas – PV may be the preferred possibility for generating electricity, or PV may be used together with wind, diesel generators and/or hydroelectric power. In such off-grid circumstances batteries are usually used to store the electric power.

In locations near the grid, however, feeding the grid using PV panels is more practical, and leads to optimum use of the investment in the photovoltaic system. This requires both regulatory and commercial preparation, including net-metering and feed-in agreements. To provide for possible power failure, some grid tied systems are set up to allow local use disconnected from the grid. Most photovoltaics are grid connected. In the event the grid fails, the local system must not feed the grid to prevent the possible creation of dangerous islanding.

PV in transport

Main article: Photovoltaics in transport

PV has traditionally been used for auxiliary power in space. PV is rarely used to provide motive power in transport applications, but is being used increasingly to provide auxiliary power in boats and cars. Recent advances in solar cell technology, however, have shown the cell's ability to administer significant hydrogen production, making it one of the top prospects for alternative energy for automobiles.

PV in standalone devices

Solar parking meter.

Till a decade or so ago, PV was used frequently to power calculators and novelty devices. Improvements in integrated circuits and low power LCD displays make it possible to power such devices for several years between battery changes, making PV use less common. In contrast, solar powered remote fixed devices have seen increasing use recently in locations where significant connection cost makes grid power prohibitively expensive. Such applications include parking meters, emergency telephones, temporary traffic signs, and remote guard posts & signals.

Rural electrification

Developing countries where many villages are often more than five kilometers away from grid power have begun using photovoltaics. In remote locations in India a rural lighting program has been providing solar powered LED lighting to replace kerosene lamps. The solar powered lamps were sold at about the cost of a few month's supply of kerosene. Cuba is working to provide solar power for areas that are off grid. These are areas where the social costs and benefits offer an excellent case for going solar though the lack of profitability could relegate such endeavors to humanitarian goals.

Solar roadways

A 45 mi (72 km) section of roadway in Idaho is being used to test the possibility of installing solar panels into the road surface, as roads are generally unobstructed to the sun and represent about the percentage of land area needed to replace other energy sources with solar power.

Economics of PV

See also: Renewable energy commercialization

US average daily solar energy insolation received by a latitude tilt photovoltaic cell.

Power costs

The PV industry is beginning to adopt levelized cost of energy (LCOE) as the unit of cost. The results of a sample calculation can be found on pp. 52, 53 of the 2007 DOE report describing the plans for solar power 2007-2011 [1]. For a 10 MW plant in Phoenix, AZ, the LCOE is estimated at $0.15 to 0.22/kWh.

The table below is a pure mathematical calculation. It illustrates the calculated total cost in US cents per kilowatt-hour of electricity generated by a photovoltaic system as function of the investment cost and the efficiency, assuming some accounting parameters such as cost of capital and depreciation period. The row headings on the left show the total cost, per peak kilowatt (kWp), of a photovoltaic installation. The column headings across the top refer to the annual energy output in kilowatt-hours expected from each installed peak kilowatt. This varies by geographic region because the average insolation depends on the average cloudiness and the thickness of atmosphere traversed by the sunlight. It also depends on the path of the sun relative to the panel and the horizon.

Panels can be mounted at an angle based on latitude, which can add to total energy output. Solar tracking can also be utilized to access even more perpendicular sunlight, thereby raising the total energy output. The calculated values in the table reflect the total cost in cents per kilowatt-hour produced. They assume a 10% total capital cost (for instance 4% interest rate, 1% operating and maintenance cost, and depreciation of the capital outlay over 20 years).

Table showing average cost in cents/kWh over 20 years for solar power panels

	Insolation
Cost	2400 kWh/kWp•y	2200 kWh/kWp•y	2000 kWh/kWp•y	1800 kWh/kWp•y	1600 kWh/kWp•y	1400 kWh/kWp•y	1200 kWh/kWp•y	1000 kWh/kWp•y	800 kWh/kWp•y
200 $/kWp	0.8	0.9	1.0	1.1	1.3	1.4	1.7	2.0	2.5
600 $/kWp	2.5	2.7	3.0	3.3	3.8	4.3	5.0	6.0	7.5
1000 $/kWp	4.2	4.5	5.0	5.6	6.3	7.1	8.3	10.0	12.5
1400 $/kWp	5.8	6.4	7.0	7.8	8.8	10.0	11.7	14.0	17.5
1800 $/kWp	7.5	8.2	9.0	10.0	11.3	12.9	15.0	18.0	22.5
2200 $/kWp	9.2	10.0	11.0	12.2	13.8	15.7	18.3	22.0	27.5
2600 $/kWp	10.8	11.8	13.0	14.4	16.3	18.6	21.7	26.0	32.5
3000 $/kWp	12.5	13.6	15.0	16.7	18.8	21.4	25.0	30.0	37.5
3400 $/kWp	14.2	15.5	17.0	18.9	21.3	24.3	28.3	34.0	42.5
3800 $/kWp	15.8	17.3	19.0	21.1	23.8	27.1	31.7	38.0	47.5
4200 $/kWp	17.5	19.1	21.0	23.3	26.3	30.0	35.0	42.0	52.5
4600 $/kWp	19.2	20.9	23.0	25.6	28.8	32.9	38.3	46.0	57.5
5000 $/kWp	20.8	22.7	25.0	27.8	31.3	35.7	41.7	50.0	62.5

Grid parity

Further information: Low cost solar cell

Grid parity, the point at which photovoltaic electricity is equal to or cheaper than grid power, is achieved first in areas with abundant sun and high costs for electricity such as in California and Japan.

Grid parity has been reached in Hawaii and other islands that otherwise use diesel fuel to produce electricity.

George W. Bush has set 2015 as the date for grid parity in the USA.. Abengoa Solar has announced the award of two R&D projects in the field of Concentrating Solar Power (CSP) by the US Department of Energy that total over $14 million. The goal of the DOE R&D program, working in collaboration with partners such as Abengoa Solar, is to develop C.S.P. technologies that are competitive with conventional energy sources (grid parity) by 2015.

General Electric's Chief Engineer predicts grid parity without subsidies in sunny parts of the United States by around 2015. Other companies predict an earlier date: the cost of solar power will be below grid parity for more than half of residential customers and 10% of commercial customers in the OECD, as long as grid electricity prices do not decrease through 2010.

The fully-loaded cost (cost not price) of solar electricity is $0.25/kWh or less in most of the OECD countries. Within three years, the fully-loaded cost is likely to fall below $0.15/kWh for most of the OECD and reach $0.10/kWh in sunnier regions. These cost levels are driving three emerging trends:

1. vertical integration of the supply chain;
2. origination of power purchase agreements (PPAs) by solar power companies;
3. unexpected risk for traditional power generation companies, grid operators and turbine manufacturers.

Financial incentives

Main article: PV financial incentives

The political purpose of incentive policies for PV is to grow the industry even where the cost of PV is significantly above grid parity, to allow it to achieve the economies of scale necessary to reach grid parity. The policies are implemented to promote national energy independence, high tech job creation and reduction of CO₂ emissions.

Three incentive mechanisms are used (often in combination):

• investment subsidies: the authorities refund part of the cost of installation of the system,
• Feed-in Tariffs (FIT)/Net metering: the electricity utility buys PV electricity from the producer under a multiyear contract at a guaranteed rate.
• Renewable Energy Certificates ("RECs")

With investment subsidies, the financial burden falls upon the taxpayer, while with feed-in tariffs the extra cost is distributed across the utilities' customer bases. While the investment subsidy may be simpler to administer, the main argument in favour of feed-in tariffs is the encouragement of quality. Investment subsidies are paid out as a function of the nameplate capacity of the installed system and are independent of its actual power yield over time, thus rewarding the overstatement of power and tolerating poor durability and maintenance. Some electric companies offer rebates to their customers, such as Austin Energy in Texas, which offers $4.50/watt installed up to $13,500.

With feed-in tariffs, the financial burden falls upon the consumer. They reward the number of kilowatt-hours produced over a long period of time, but because the rate is set by the authorities, it may result in perceived overpayment. The price paid per kilowatt-hour under a feed-in tariff exceeds the price of grid electricity. Net metering refers to the case where the price paid by the utility is the same as the price charged. Net metering is particularly important because it can be done with no changes to standard electricity meters, which accurately measure power in both directions and automatically report the difference, and because it allows homeowners and businesses to generate electricity at a different time from consumption, effectively using the grid as a giant storage battery. As more photovoltaics are used ultimately storage will need to be provided, normally in the form of pumped hydro-storage. Normally with net metering deficits are billed each month, while surpluses are rolled over to the following month and paid annually.

Where price setting by supply and demand is preferred, RECs can be used. In this mechanism, a renewable energy production or consumption target is set, and the consumer or producer is obliged to purchase renewable energy from whoever provides it the most competitively. The producer is paid via an REC. In principle this system delivers the cheapest renewable energy, since the lowest bidder will win. However, uncertainties about the future value of energy produced are a brake on investment in capacity, and the higher risk increases the cost of capital borrowed.

The Japanese government through its Ministry of International Trade and Industry ran a successful programme of subsidies from 1994 to 2003. By the end of 2004, Japan led the world in installed PV capacity with over 1.1 GW.

In 2004, the German government introduced the first large-scale feed-in tariff system, under a law known as the 'EEG' (Erneuerbare Energien Gesetz) which resulted in explosive growth of PV installations in Germany. At the outset the FIT was over 3x the retail price or 8x the industrial price. The principle behind the German system is a 20 year flat rate contract. The value of new contracts is programmed to decrease each year, in order to encourage the industry to pass on lower costs to the end users. The programme has been more successful than expected with over 1GW installed in 2006, and political pressure is mounting to decrease the tariff to lessen the future burden on consumers.

Subsequently Spain, Italy, Greece and France introduced feed-in tariffs. None have replicated the programmed decrease of FIT in new contracts though, making the German incentive relatively less and less attractive compared to other countries. The French FIT offers a uniquely high premium (EUR 0.55/kWh) for building integrated systems. California, Greece, France and Italy have 30-50% more insolation than Germany making them financially more attractive.

In 2006 California approved the 'California Solar Initiative', offering a choice of investment subsidies or FIT for small and medium systems and a FIT for large systems. The small-system FIT of $0.39 per kWh (far less than EU countries) expires in just 5 years, and the alternate "EPBB" residential investment incentive is modest, averaging perhaps 20% of cost. All California incentives are scheduled to decrease in the future depending as a function of the amount of PV capacity installed.

At the end of 2006, the Ontario Power Authority (Canada) began its Standard Offer Program, the first in North America for small renewable projects (10MW or less). This guarantees a fixed price of $0.42 CDN per kWh over a period of twenty years. Unlike net metering, all the electricity produced is sold to the OPA at the SOP rate. The generator then purchases any needed electricity at the current prevailing rate (e.g., $0.055 per kWh). The difference should cover all the costs of installation and operation over the life of the contract.

The price per kilowatt hour or per peak kilowatt of the FIT or investment subsidies is only one of three factors that stimulate the installation of PV. The other two factors are insolation (the more sunshine, the less capital is needed for a given power output) and administrative ease of obtaining permits and contracts.

Unfortunately the complexity of approvals in California, Spain and Italy has prevented comparable growth to Germany even though the return on investment is better.

In some countries, additional incentives are offered for BIPV compared to stand alone PV.

• France + EUR 0.25/kWh (EUR 0.30 + 0.25 = 0.55/kWh total)
• Italy + EUR 0.04-0.09 kWh
• Germany + EUR 0.05/kWh (facades only)

Environmental impacts

Unlike fossil fuel based technologies, solar power does not lead to any harmful emissions during operation, but the production of the panels leads to some amount of pollution. This is often referred to as the energy input to output ratio. In some analysis, if the energy input to produce it is higher than the output it produces it can be considered environmentally more harmful than beneficial. Also, placement of photovoltaics affects the environment. If they are located where photosynthesizing plants would normally grow, they simply substitute one potentially renewable resource (biomass) for another. It should be noted, however, that the biomass cycle converts solar radiation energy to electrical energy with significantly less efficiency than photovoltaic cells alone. And if they are placed on the sides of buildings (such as in Manchester) or fences, or rooftops (as long as plants would not normally be placed there), or in the desert they are purely additive to the renewable power base.

Greenhouse gases

Life cycle greenhouse gas emissions are now in the range of 25-32 g/kWh and this could decrease to 15 g/kWh in the future. For comparison, a combined cycle gas-fired power plant emits some 400 g/kWh and a coal-fired power plant 915 g/kWh and with carbon capture and storage some 200 g/kWh. Only nuclear power and wind are better, emitting 6-25 g/kWh and 11 g/kWh on average. Using renewable energy sources in manufacturing and transportation would further drop photovoltaic emissions.

Cadmium

One issue that has often raised concerns is the use of cadmium in cadmium telluride solar cells (CdTe is only used in a few types of PV panels). Cadmium in its metallic form is a toxic substance that has the tendency to accumulate in ecological food chains. The amount of cadmium used in thin-film PV modules is relatively small (5-10 g/m²) and with proper emission control techniques in place the cadmium emissions from module production can be almost zero. Current PV technologies lead to cadmium emissions of 0.3-0.9 microgram/kWh over the whole life-cycle. Most of these emissions actually arise through the use of coal power for the manufacturing of the modules, and coal and lignite combustion leads to much higher emissions of cadmium. Life-cycle cadmium emissions from coal is 3.1 microgram/kWh, lignite 6.2, and natural gas 0.2 microgram/kWh.

Note that if electricity produced by photovoltaic panels were used to manufacture the modules instead of electricity from burning coal, cadmium emissions from coal power usage in the manufacturing process could be entirely eliminated.

Energy Payback Time and Energy Returned on Energy Invested

The energy payback time is the time required to produce an amount of energy as great as what was consumed during production. The energy payback time is determined from a life cycle analysis of energy.

Another key indicator of environmental performance, tightly related to the energy payback time, is the ratio of electricity generated divided by the energy required to build and maintain the equipment. This ratio is called the energy returned on energy invested (EROEI). Of course, little is gained if it takes as much energy to produce the modules as they produce in their lifetimes. This should not be confused with the economic return on investment, which varies according to local energy prices, subsidies available and metering techniques.

Life-cycle analyses show that the energy intensity of typical solar photovoltaic technologies is rapidly evolving. In 2000 the energy payback time was estimated as 8 to 11 years, but more recent studies suggest that technological progress has reduced this to 1.5 to 3.5 years for crystalline silicon PV systems .

Thin film technologies now have energy pay-back times in the range of 1-1.5 years (S.Europe). With lifetimes of such systems of at least 30 years, the EROEI is in the range of 10 to 30. They thus generate enough energy over their lifetimes to reproduce themselves many times (6-31 reproductions, the EROEI is a bit lower) depending on what type of material, balance of system (or BOS), and the geographic location of the system.

Disadvantages

• Cost may not cover lifespan savings unless a preferencial feed-in tarif is offered by the grid network. But this depends on location and energy prices.
• Solar electricity is often initially more expensive than electricity generated by other sources.
• Solar electricity is not available at night and is less available in cloudy weather conditions. Therefore, a storage or complementary power system is required.
• Limited power density: Average daily insolation in the contiguous U.S. is 3-7 kW·h/m² and on average lower in Europe.
• Solar cells produce DC which must be converted to AC (using a grid tie inverter) when used in currently existing distribution grids. This incurs an energy loss of 4-12%.

Advantages

• The 89 petawatts of sunlight reaching the earth's surface is plentiful - almost 6,000 times more than the 15 terawatts of average power consumed by humans. Additionally, solar electric generation has the highest power density (global mean of 170 W/m²) among renewable energies.
• Solar power is pollution free during use. Production end wastes and emissions are manageable using existing pollution controls. End-of-use recycling technologies are under development.
• Facilities can operate with little maintenance or intervention after initial setup.
• Solar electric generation is economically superior where grid connection or fuel transport is difficult, costly or impossible. Examples include satellites, island communities, remote locations and ocean vessels.
• When grid-connected, solar electric generation can displace the highest cost electricity during times of peak demand (in most climatic regions), can reduce grid loading, and can eliminate the need for local battery power for use in times of darkness and high local demand; such application is encouraged by net metering. Time-of-use net metering can be highly favorable to small photovoltaic systems.
• Grid-connected solar electricity can be used locally thus reducing transmission/distribution losses (transmission losses were approximately 7.2% in 1995).
• Once the initial capital cost of building a solar power plant has been spent, operating costs are extremely low compared to existing power technologies.
• Compared to fossil and nuclear energy sources, very little research-money has been invested in the development of solar cells, so there is much room for improvement. Nevertheless, experimental high efficiency solar cells already have efficiencies of over 40% and efficiencies are rapidly rising while mass production costs are rapidly falling.

Photovoltaics companies

See also: List of photovoltaics companies

Photovoltaic industry associations

• ASIF: Spanish PV Industry Associationin Spanish only
• GIFI: Italian PV Industry Associationin Italian only
• SER: french renewable energy Industry organizationin French only
• BSW: German Solar Industry Associationin German, with English summary
• Canadian Solar industry Association
• EPIA: European Photovoltaic Industry association
• IPVEA: International Photovoltaic Equipment Association
• JPEA: Japanese Photovoltaic Energy Association in Japanese only
• SEIA: Solar Energy Industries Association US trade association
• SEMI: Semiconductor Equipment and Materials International Global industry association

Photovoltaics research institutes

There are many research institutions and departments at universities around the world who are active in photovoltaics research. Countries which are particularly active include Germany, Spain, Japan, Australia, China, and the USA.

Some universities and institutes which have a photovoltaics research department.

• Solar Energy Materials Research Group at Lawrence Berkeley National Laboratory
• The Center for Functional Nanomaterials at Brookhaven National Laboratory
• Solar Energy Laboratory at University of Southampton
• National Renewable Energy Laboratory NREL
• Energy & Environmental Technology Application Center at the College of Nanoscale Science and Engineering SUNY at Albany
• Institut für Solare Energiesysteme ISE at the Fraunhofer Institute
• Energy research Centre of the Netherlands (ECN)
• Imperial College London: Experimental Solid State Physics
• Instituto de Energía Solar, at Universidad Politécnica de Madrid
• Centre for Renewable Energy Systems Technology, at Loughborough University
• School of Photovoltaic and Renewable Energy Engineering at The University of New South Wales
• Centre for Sustainable Energy Systems at the Australian National University
• Ecole Polytechnique Fédérale de Lausanne Prof. Graetzel invented dye sensitized cells here
• Advanced Energy Systems at Helsinki University of Technology
• Institute of Materials Research, Salford University
• The Centre for Electronic Devices and Materials at Sheffield Hallam University
• The Centre for Advanced Investigations on Electric Engineering at The National Polytechnic Institute of Mexico
• The Solar Caliometry Lab at Queen's University
• Institute of microtechnology at University of Neuchatel Switzerland
• University of Konstanz
• Arizona State University Photovoltaic Testing Laboratory
• Institute of Energy Conversion at University of Delaware
• World Alliance for Decentralized Energy
• Florida Solar Energy Center at University of Central Florida
• Linz Institute for Organic Solar Cells (LIOS)

See also

• Active solar
• Carbon nanotubes in photovoltaics
• Concentrator photovoltaics
• Deployment of solar power to energy grids
• Distributed Energy Resources
• Electranet
• Fluorescent solar collector
• Green technology
• Grid-tied electrical system
• High efficiency solar cells
• Infrared
• Islanding
• Low cost solar cell
• Maximum power point tracker
• Microgeneration
• Microgeneration Certification Scheme
• Photoelectrochemical cell
• Photovoltaic and renewable energy engineering in Australia
• Photovoltaics in transport
• Renewable Energy Focus magazine
• Renewable energy
• Renewable energy in the European Union
• Solar vehicle
• Solar thermal energy
• Solar energy
• Solar cell
• Solar panel
• Solar air conditioning
• World Council for Renewable Energy

External links

Publicly funded free data sources

• EU PV Technology Platform - forum for stakeholders to influence EU policy,
• Trends in photovoltaic applications in selected IEA countries between 1992 and 2004
• IEA PVPS annual report 2006
• Photovoltaic Geographical Information System (PVGIS)
• US Department of Energy - Energy Efficiency and Renewable Energy
• DSIRE Listing of US state, local, utility, and federal incentives for renewable energy and energy efficiency.
• Find Solar US solar estimator and solar pro locator (joint partnership with DOE, CEC, Energy Matters, ASES).
• PV Estimation Utility for Europe and Africa European Commission Joint Research Centre

Live data

• Europe
• Germany
• United States
• New Zealand schools

Others

• World's largest photovoltaic power plants