Fracking
![]() Schematic depiction of hydraulic fracturing for shale gas. | |
Process type | Mechanical |
---|---|
Industrial sector(s) | Mining |
Main technologies or sub-processes | Fluid pressure |
Product(s) | Natural gas Petroleum |
Inventor | Floyd Farris; J.B. Clark (Stanolind Oil and Gas Corporation) |
Year of invention | 1947 |
Hydraulic fracturing is the propagation of fractures in a rock layer by a pressurized fluid. Some hydraulic fractures form naturally—certain veins or dikes are examples—and can create conduits along which gas and petroleum from source rocks may migrate to reservoir rocks. Induced hydraulic fracturing or hydrofracturing, commonly known as fracing, fraccing, or fracking, is a technique used to release petroleum, natural gas (including shale gas, tight gas, and coal seam gas), or other substances for extraction.[1] This type of fracturing creates fractures from a wellbore drilled into reservoir rock formations.
The first use of hydraulic fracturing was in 1947. However, it was only in 1998 that modern fracturing technology, referred to as horizontal slickwater fracturing, made possible the economical extraction of shale gas; this new technology was first used in the Barnett Shale in Texas.[1][2][3] The energy from the injection of a highly pressurized hydraulic fracturing fluid creates new channels in the rock, which can increase the extraction rates and ultimate recovery of hydrocarbons.
Proponents of hydraulic fracturing point to the economic benefits from vast amounts of formerly inaccessible hydrocarbons the process can extract.[4] Opponents point to potential environmental impacts, including contamination of ground water, risks to air quality, the migration of gases and hydraulic fracturing chemicals to the surface, surface contamination from spills and flowback and the health effects of these.[5] For these reasons hydraulic fracturing has come under scrutiny internationally, with some countries suspending or banning it.[6][7]
Geology
Mechanics
Fracturing in rocks at depth tends to be suppressed by the confining pressure, due to the load caused by the overlying rock strata. This is particularly so in the case of "tensile" (Mode 1) fractures, which require the walls of the fracture to move apart, working against this confining pressure. Hydraulic fracturing occurs when the effective stress is reduced sufficiently by an increase in the pressure of fluids within the rock, such that the minimum principal stress becomes tensile and exceeds the tensile strength of the material.[8][9] Fractures formed in this way will in the main be oriented in the plane perpendicular to the minimum principal stress and for this reason induced hydraulic fractures in wellbores are sometimes used to determine the orientation of stresses.[10] In natural examples, such as dikes or vein-filled fractures, the orientations can be used to infer past states of stress.[11]
Veins
Most vein systems are a result of repeated hydraulic fracturing during periods of relatively high pore fluid pressure. This is particularly noticeable in the case of "crack-seal" veins, where the vein material can be seen to have been added in a series of discrete fracturing events, with extra vein material deposited on each occasion.[12] One mechanism to demonstrate such examples of long-lasting repeated fracturing is the effects of seismic activity, in which the stress levels rise and fall episodically and large volumes of fluid may be expelled from fluid-filled fractures during earthquakes. This process is referred to as "seismic pumping".[13]
Dikes
Low-level minor intrusions such as dikes propagate through the crust in the form of fluid-filled cracks, although in this case the fluid is magma. In sedimentary rocks with a significant water content the fluid at the propagating fracture tip will be steam.[14]
History
Fracturing as a method to stimulate shallow, hard rock oil wells dates back to the 1860s. It was applied by oil producers in the US states of Pennsylvania, New York, Kentucky, and West Virginia by using liquid and later also solidified nitroglycerin. Later, the same method was applied to water and gas wells. The idea to use acid as a nonexplosive fluid for well stimulation was introduced in the 1930s. Due to acid etching, fractures would not close completely and therefore productivity was enhanced. The same phenomenon was discovered with water injection and squeeze cementing operations.[15]
The relationship between well performance and treatment pressures was studied by Floyd Farris of Stanolind Oil and Gas Corporation. This study became a basis of the first hydraulic fracturing experiment, which was conducted in 1947 at the Hugoton gas field in Grant County of southwestern Kansas by Stanolind.[1][15] For the well treatment 1,000 US gallons (3,800 L; 830 imp gal) of gelled gasoline and sand from the Arkansas River was injected into the gas-producing limestone formation at 2,400 feet (730 m). The experiment was not very successful as deliverability of the well did not change appreciably. The process was further described by J.B. Clark of Stanolind in his paper published in 1948. A patent on this process was issued in 1949 and an exclusive license was granted to the Halliburton Oil Well Cementing Company. On March 17, 1949, Halliburton performed the first two commercial hydraulic fracturing treatments in Stephens County, Oklahoma, and Archer County, Texas.[15] Since then, hydraulic fracturing has been used to stimulate approximately a million oil and gas wells.[16]
In the Soviet Union, the first hydraulic proppant fracturing was carried out in 1952. In Western Europe in 1977–1985, hydraulic fracturing was conducted at Rotliegend and Carboniferous gas-bearing sandstones in Germany, Netherlands onshore and offshore gas fields, and the United Kingdoms sector of the North Sea. Other countries in Europe and Northern Africa included Norway, the Soviet Union, Poland, Czechoslovakia, Yugoslavia, Hungary, Austria, France, Italy, Bulgaria, Romania, Turkey, Tunisia, and Algeria.[17]
Due to shale's high porosity and low permeability, technology research, development and demonstration were necessary before hydraulic fracturing could be commercially applied to shale gas deposits. In the 1970s the United States government initiated the Eastern Gas Shales Project, a set of dozens of public-private hydraulic fracturing pilot demonstration projects. During the same period, the Gas Research Institute, a gas industry research consortium, received approval for research and funding from the Federal Energy Regulatory Commission.[18] In 1977, the Department of Energy pioneered massive hydraulic fracturing in tight sandstone formations. In 1997, based on earlier techniques used by Union Pacific Resources, now part of Anadarko Petroleum Corporation, Mitchell Energy, now part of Devon Energy, developed the hydraulic fracturing technique known as "slickwater fracturing" which involves adding chemicals to water to increase the fluid flow, that made the shale gas extraction economical.[2][3][19]
As of 2013, in addition to the United States several countries are planning to use hydraulic fracturing for unconventional oil and gas production.[20][21][22]
Induced hydraulic fracturing
According to the United States Environmental Protection Agency (EPA) hydraulic fracturing is a process to stimulate a natural gas, oil, or geothermal energy well to maximize the extraction. The whole process is defined as including the acquisition of source water, well construction, well stimulation, and waste disposal.[23]
Uses
The technique of hydraulic fracturing is used to increase or restore the rate at which fluids, such as petroleum, water, or natural gas can be recovered from subterranean natural reservoirs. Reservoirs are typically porous sandstones, limestones or dolomite rocks, but also include "unconventional reservoirs" such as shale rock or coal beds. Hydraulic fracturing enables the production of natural gas and oil from rock formations deep below the earth's surface (generally 5,000–20,000 feet (1,500–6,100 m)). At such depth, there may not be sufficient permeability or reservoir pressure to allow natural gas and oil to flow from the rock into the wellbore at economic rates. Thus, creating conductive fractures in the rock is pivotal to extract gas from shale reservoirs because of the extremely low natural permeability of shale, which is measured in the microdarcy to nanodarcy range.[24] Fractures provide a conductive path connecting a larger volume of the reservoir to the well. So-called "super fracing", which creates cracks deeper in the rock formation to release more oil and gas, will increase efficiency of hydraulic fracturing.[25] The yield for a typical shale gas well generally falls off sharply after the first year or two.[26]
While the main industrial use of hydraulic fracturing is in arousing production from oil and gas wells,[27][28][29] hydraulic fracturing is also applied:
- To stimulate groundwater wells[30]
- To precondition or induce rock to cave in mining[31]
- As a means of enhancing waste remediation processes, usually hydrocarbon waste or spills[32]
- To dispose of waste by injection into deep rock formations[33]
- As a method to measure the stress in the Earth[34]
- For heat extraction to produce electricity in an enhanced geothermal systems[35]
- To increase injection rates for geologic sequestration of CO2[36]
Method
A hydraulic fracture is formed by pumping the fracturing fluid into the wellbore at a rate sufficient to increase pressure downhole to exceed that of the fracture gradient (pressure gradient) of the rock.[37] The fracture gradient is defined as the pressure increase per unit of the depth due to its density and it is usually measured in pounds per square inch per foot or bars per meter. The rock cracks and the fracture fluid continues further into the rock, extending the crack still further, and so on. Operators typically try to maintain "fracture width", or slow its decline, following treatment by introducing into the injected fluid a proppant – a material such as grains of sand, ceramic, or other particulates, that prevent the fractures from closing when the injection is stopped and the pressure of the fluid is reduced. Consideration of proppant strengths and prevention of proppant failure becomes more important at greater depths where pressure and stresses on fractures are higher. The propped fracture is permeable enough to allow the flow of formation fluids to the well. Formation fluids include gas, oil, salt water, fresh water and fluids introduced to the formation during completion of the well during fracturing.[37]
During the process fracturing fluid leakoff, loss of fracturing fluid from the fracture channel into the surrounding permeable rock occurs. If not controlled properly, it can exceed 70% of the injected volume. This may result in formation matrix damage, adverse formation fluid interactions, or altered fracture geometry and thereby decreased production efficiency.[38]
The location of one or more fractures along the length of the borehole is strictly controlled by various methods that create or seal off holes in the side of the wellbore. Typically, hydraulic fracturing is performed in cased wellbores and the zones to be fractured are accessed by perforating the casing at those locations.[39]
Hydraulic-fracturing equipment used in oil and natural gas fields usually consists of a slurry blender, one or more high-pressure, high-volume fracturing pumps (typically powerful triplex or quintuplex pumps) and a monitoring unit. Associated equipment includes fracturing tanks, one or more units for storage and handling of proppant, high-pressure treating iron, a chemical additive unit (used to accurately monitor chemical addition), low-pressure flexible hoses, and many gauges and meters for flow rate, fluid density, and treating pressure.[40] Fracturing equipment operates over a range of pressures and injection rates, and can reach up to 100 megapascals (15,000 psi) and 265 litres per second (9.4 cu ft/s) (100 barrels per minute).[41]
Well types
A distinction can be made between conventional or low-volume hydraulic fracturing used to stimulate high-permeability reservoirs to frac a single well, and unconventional or high-volume hydraulic fracturing, used in the completion of tight gas and shale gas wells as unconventional wells are deeper and require higher pressures than conventional vertical wells.[42] In addition to hydraulic fracturing of vertical wells, it is also performed in horizontal wells. When done in already highly permeable reservoirs such as sandstone-based wells, the technique is known as "well stimulation".[29]
Horizontal drilling involves wellbores where the terminal drillhole is completed as a "lateral" that extends parallel with the rock layer containing the substance to be extracted. For example, laterals extend 1,500 to 5,000 feet (460 to 1,520 m) in the Barnett Shale basin in Texas, and up to 10,000 feet (3,000 m) in the Bakken formation in North Dakota. In contrast, a vertical well only accesses the thickness of the rock layer, typically 50–300 feet (15–91 m). Horizontal drilling also reduces surface disruptions as fewer wells are required to access a given volume of reservoir rock. Drilling usually induces damage to the pore space at the wellbore wall, reducing the permeability at and near the wellbore. This reduces flow into the borehole from the surrounding rock formation, and partially seals off the borehole from the surrounding rock. Hydraulic fracturing can be used to restore permeability.[43]
Fracturing fluids
High-pressure fracture fluid is injected into the wellbore, with the pressure above the fracture gradient of the rock. The two main purposes of fracturing fluid is to extend fractures and to carry proppant into the formation, the purpose of which is to stay there without damaging the formation or production of the well. Two methods of transporting the proppant in the fluid are used – high-rate and high-viscosity. High-viscosity fracturing tends to cause large dominant fractures, while high-rate (slickwater) fracturing causes small spread-out micro-fractures.[citation needed]
This fracture fluid contains water-soluble gelling agents (such as guar gum) which increase viscosity and efficiently deliver the proppant into the formation.[44]
The fluid injected into the rock is typically a slurry of water, proppants, and chemical additives.[45] Additionally, gels, foams, and compressed gases, including nitrogen, carbon dioxide and air can be injected. Typically, of the fracturing fluid 90% is water and 9.5% is sand with the chemical additives accounting to about 0.5%.[37][46][47]
A proppant is a material that will keep an induced hydraulic fracture open, during or following a fracturing treatment, and can be gel, foam, or slickwater-based. Fluids make tradeoffs in such material properties as viscosity, where more viscous fluids can carry more concentrated proppant; the energy or pressure demands to maintain a certain flux pump rate (flow velocity) that will conduct the proppant appropriately; pH, various rheological factors, among others. Types of proppant include silica sand, resin-coated sand, and man-made ceramics. These vary depending on the type of permeability or grain strength needed. The most commonly used proppant is silica sand, though proppants of uniform size and shape, such as a ceramic proppant, is believed to be more effective. Due to a higher porosity within the fracture, a greater amount of oil and natural gas is liberated.[48]
The fracturing fluid varies in composition depending on the type of fracturing used, the conditions of the specific well being fractured, and the water characteristics. A typical fracture treatment uses between 3 and 12 additive chemicals.[37] Although there may be unconventional fracturing fluids, the typical used chemical additives are:
- Acids—hydrochloric acid (usually 28%-5%), or acetic acid is used in the pre-fracturing stage for cleaning the perforations and initiating fissure in the near-wellbore rock.[47]
- Sodium chloride (salt)—delays breakdown of the gel polymer chains.[47]
- Polyacrylamide and other friction reducers—minimizes the friction between fluid and pipe, thus allowing the pumps to pump at a higher rate without having greater pressure on the surface.[47]
- Ethylene glycol—prevents formation of scale deposits in the pipe.[47]
- Borate salts—used for maintaining fluid viscosity during the temperature increase.[47]
- Sodium and potassium carbonates—used for maintaining effectiveness of crosslinkers.[47]
- Glutaraldehyde—used as disinfectant of the water (bacteria elimination).[47]
- Guar gum and other water-soluble gelling agents—increases viscosity of the fracturing fluid to deliver more efficiently the proppant into the formation.[44][47]
- Citric acid—used for corrosion prevention.
- Isopropanol—increases the viscosity of the fracture fluid.[47]
The most common chemical used for hydraulic fracturing in the United States in 2005–2009 was methanol, while some other most widely used chemicals were isopropyl alcohol, 2-butoxyethanol, and ethylene glycol.[49]
Typical fluid types are:
- Conventional linear gels. These gels are cellulose derivatives (carboxymethyl cellulose, hydroxyethyl cellulose, carboxymethyl hydroxyethyl cellulose, hydroxypropyl cellulose, methyl hydroxyl ethyl cellulose), guar or its derivatives (hydroxypropyl guar, carboxymethyl hydroxypropyl guar) based, with other chemicals providing the necessary chemistry for the desired results.
- Borate-crosslinked fluids. These are guar-based fluids cross-linked with boron ions (from aqueous borax/boric acid solution). These gels have higher viscosity at pH 9 onwards and are used to carry proppants. After the fracturing job the pH is reduced to 3–4 so that the cross-links are broken and the gel is less viscous and can be pumped out.
- Organometallic-crosslinked fluids zirconium, chromium, antimony, titanium salts are known to crosslink the guar based gels. The crosslinking mechanism is not reversible. So once the proppant is pumped down along with the cross-linked gel, the fracturing part is done. The gels are broken down with appropriate breakers.[44]
- Aluminium phosphate-ester oil gels. Aluminium phosphate and ester oils are slurried to form cross-linked gel. These are one of the first known gelling systems.
For slickwater it is common to include sweeps or a reduction in the proppant concentration temporarily to ensure the well is not overwhelmed with proppant causing a screen-off.[50] As the fracturing process proceeds, viscosity reducing agents such as oxidizers and enzyme breakers are sometimes then added to the fracturing fluid to deactivate the gelling agents and encourage flowback.[44] The oxidizer reacts with the gel to break it down, reducing the fluid's viscosity and ensuring that no proppant is pulled from the formation. An enzyme acts as a catalyst for the breaking down of the gel. Sometimes pH modifiers are used to break down the crosslink at the end of a hydraulic fracturing job, since many require a pH buffer system to stay viscous.[50] At the end of the job the well is commonly flushed with water (sometimes blended with a friction reducing chemical) under pressure. Injected fluid is to some degree recovered and is managed by several methods, such as underground injection control, treatment and discharge, recycling, or temporary storage in pits or containers while new technology is being continually being developed and improved to better handle waste water and improve re-usability.[37]
Fracture monitoring
Measurements of the pressure and rate during the growth of a hydraulic fracture, as well as knowing the properties of the fluid and proppant being injected into the well provides the most common and simplest method of monitoring a hydraulic fracture treatment. This data, along with knowledge of the underground geology can be used to model information such as length, width and conductivity of a propped fracture.[37]
Injection of radioactive tracers, along with the other substances in hydraulic-fracturing fluid, is sometimes used to determine the injection profile and location of fractures created by hydraulic fracturing.[51] The radiotracer is chosen to have the readily detectable radiation, appropriate chemical properties, and a half life and toxicity level that will minimize initial and residual contamination.[52] Radioactive isotopes chemically bonded to glass (sand) and/or resin beads may also be injected to track fractures.[53] For example, plastic pellets coated with 10 GBq of Ag-110mm may be added to the proppant or sand may be labelled with Ir-192 so that the proppant's progress can be monitored.[52] Radiotracers such as Tc-99m and I-131 are also used to measure flow rates.[52] The Nuclear Regulatory Commission publishes guidelines which list a wide range of radioactive materials in solid, liquid and gaseous forms that may be used as tracers and limit the amount that may be used per injection and per well of each radionuclide.[53]
For more advanced applications, microseismic monitoring is sometimes used to estimate the size and orientation of hydraulically induced fractures. Microseismic activity is measured by placing an array of geophones in a nearby wellbore. By mapping the location of any small seismic events associated with the growing hydraulic fracture, the approximate geometry of the fracture is inferred. Tiltmeter arrays, deployed on the surface or down a well, provide another technology for monitoring the strains produced by hydraulic fracturing.[54]
Horizontal completions
Since the early 2000s, advances in drilling and completion technology have made drilling horizontal wellbores much more economical. Horizontal wellbores allow for far greater exposure to a formation than a conventional vertical wellbore. This is particularly useful in shale formations which do not have sufficient permeability to produce economically with a vertical well. Such wells when drilled onshore are now usually hydraulically fractured in a number of stages, especially in North America. The type of wellbore completion used will affect how many times the formation is fractured, and at what locations along the horizontal section of the wellbore.[55]
In North America, shale reservoirs such as the Bakken, Barnett, Montney, Haynesville, Marcellus, and most recently the Eagle Ford, Niobrara and Utica shales are drilled, completed and fractured using this method.[citation needed] The method by which the fractures are placed along the wellbore is most commonly achieved by one of two methods, known as "plug and perf" and "sliding sleeve".[56]
The wellbore for a plug and perf job is generally composed of standard joints of steel casing, either cemented or uncemented, which is set in place at the conclusion of the drilling process. Once the drilling rig has been removed, a wireline truck is used to perforate near the end of the well, following which a fracturing job is pumped (commonly called a stage). Once the stage is finished, the wireline truck will set a plug in the well to temporarily seal off that section, and then perforate the next section of the wellbore. Another stage is then pumped, and the process is repeated as necessary along the entire length of the horizontal part of the wellbore.[57]
The wellbore for the sliding sleeve technique is different in that the sliding sleeves are included at set spacings in the steel casing at the time it is set in place. The sliding sleeves are usually all closed at this time. When the well is ready to be fractured, using one of several activation techniques, the bottom sliding sleeve is opened and the first stage gets pumped. Once finished, the next sleeve is opened which concurrently isolates the first stage, and the process repeats. For the sliding sleeve method, wireline is usually not required.[citation needed]
These completion techniques may allow for more than 30 stages to be pumped into the horizontal section of a single well if required, which is far more than would typically be pumped into a vertical well.[58]
Hydraulic fracturing has been seen as one of the key methods of extracting unconventional oil and gas resources. According to the International Energy Agency, the remaining technically recoverable resources of shale gas are estimated to amount to 208 trillion cubic metres (7.3 quadrillion cubic feet), tight gas to 76 trillion cubic metres (2.7 quadrillion cubic feet), and coalbed methane to 47 trillion cubic metres (1.7 quadrillion cubic feet). As a rule, formations of these resources have lower permeability than conventional gas formations. Therefore, depending on the geological characteristics of the formation, specific technologies (such as hydraulic fracturing) are required. Although there are also other methods to extract these resources, such as conventional drilling or horizontal drilling, hydraulic fracturing is one of the key methods making their extraction economically viable. The multi-stage fracturing technique has facilitated the development of shale gas and light tight oil production in the United States and is believed to do so in the other countries with unconventional hydrocarbon resources.[4] China is suspected of trying using cyberspies to access information about hydraulic fracturing equipment and practices in order to meet its energy needs without having to pay for outside equipment and services.[59] Significance of the extraction of unconventional hydrocarbons lies also in the fact that these resources are less concentrated than conventional oil and gas resources.[4]
Economic Impacts
In North America, hydraulic fracturing will account for nearly 70% of natural gas development in the future.[60] Hydraulic fracturing and horizontal drilling apply the latest technologies and make it commercially viable to recover shale gas and oil. In the United States, 45% of domestic natural gas production and 17% of oil production would be lost within 5 years without usage of hydraulic fracturing.[61]
In the United States, development of shale resources supported 600,000 jobs in 2010.[62] The American Chemistry Council determined that a 25% increase in the supply of ethane (a liquid derived from shale gas) could add over 400,000 jobs across the economy, provide over $4.4 billion annually in federal, state, and local tax revenue, and spur $16.2 billion in capital investment by the chemical industry.[63] They also note that the relatively low price of ethane would give United States manufacturers an essential advantage over many global competitors. Similarly, the National Association of Manufacturers estimated that high recovery of shale gas and lower natural gas prices will help U.S. manufacturers employ 1,000,000 workers by 2025 while lower feedstock and energy costs could help them reduce natural gas expenditures by as much as 11.6 billion by 2025.[64] America's Natural Gas Association (ANGA) estimates that lower gas prices will add an additional $926 of disposable household income annually between 2012 and 2015, and that the amount could increase to $2,000 by 2035.[65]
The issue of whether to export natural gas has split the business community. Manufacturers such as Dow Chemical are battling energy companies such as Exxon Mobil over whether the export of natural gas should be allowed. Manufacturers want to keep gas prices low, while energy companies have been working to raise the price of natural gas by convincing the government to allow them to export natural gas to more countries. Manufacturers are concerned that increasing exports will hurt manufacturing by causing U.S. energy prices to rise.[66]
In December 2012 the Council on Foreign Relations argued that the reduction of gas prices could have a major impact on Russia. 60% of Russia's federal revenues come from energy exports and any reduction in income from gas would be catastrophic for Russia. Economic necessity and looming bankruptcy could one day force political reform on Russia. The article suggests that Russia has therefore financed environmental groups to oppose unconventional gas extraction methods like hydraulic fracturing, because there aren't normally protests in these countries. Because of large, country wide protests, Bulgaria and Czech Republic have banned this technology.[67]
It is important to note that almost all economic studies that have been conducted thus far, have been conducted by the gas industry and have not been peer-reviewed. Slick-water hydraulic fracturing is still in its early stages and definitive conclusions regarding the long-term impact to society are hard to make without more peer-reviewed studies being conducted on the long-term impacts on the number of jobs created, unemployment rates, income, poverty levels, environment, tourism, property values, and public health[68].
Studies that have not been funded by the gas industry are in short supply, and as a result there are still many uncertainties that exist as to what the true economic effects of fracing will be. We must remember to keep in mind some of what history has shown with other extractive industry, including: the "Resource Curse," boom & bust theory, and socioeconomics[68].
The "Resource Curse" has shown that countries with great natural resource wealth tend to grow more slowly than resource-poor countries. This is primarily due to the quick economic growth that cannot be sustained once the natural resource has been depleted in the region. Communities can overcome this by developing the resources at a slow pace, thereby increasing the chances the economy and society can adjust and the crowding out effect may be reduced. Also this curse includes other negative impacts on economic growth including the increased prevalence of poverty[68].
Studies in Colorado, Texas, and Wyoming found the boom only saw modest increases in employment, wages, and median household income, and the bust usually exceeded the boom. In the coal boom in Kentucky, Ohio, Pennsylvania, and West Virginia saw that for every ten jobs produced by the coal sector during the boom, only two jobs were produced in the local-goods sector, and 3.5 were lost in the construction sector. This too can be controlled by slowing the pace of the extraction of the resource[68].
Three-hunded and one research findings regarding the socioeconomics on the impact of mining in the U.S., found that the adverse conditions significantly outweighed the positives. The studies also found that the communities in the U.S. having the highest levels of long-tern poverty, tend to be found in the places that were once the site of thriving extractive industries[68].
Environmental impact
Hydraulic fracturing has raised environmental concerns and is challenging the adequacy of existing regulatory regimes.[69] These concerns have included ground water contamination, risks to air quality, migration of gases and hydraulic fracturing chemicals to the surface, mishandling of waste, and the health effects of all these, as well as its contribution to raised atmospheric CO2 levels by enabling the extraction of previously-sequestered hydrocarbons.[5][37][49] Because hydraulic fracturing originated in the United States,[70] its history is more extensive there than in other regions. Most environmental impact studies have therefore taken place there.
Research issues
Several organizations, researchers, and media outlets have reported difficulty in conducting and reporting the results of studies on hydraulic fracturing due to industry[71][72][73] and governmental pressure, and expressed concern over possible censoring of environmental reports.[71][74][75] Researchers have recommended requiring disclosure of all hydraulic fracturing fluids, testing animals raised near fracturing sites, and closer monitoring of environmental samples.[76] After court cases concerning contamination from hydraulic fracturing are settled, the documents are sealed. The American Petroleum Institute deny that this practice has hidden problems with gas drilling, while others believe it has and could lead to unnecessary risks to public safety and health.[77]
Air
The air emissions from hydraulic fracturing are related to methane leaks originating from wells, and emissions from the diesel or natural gas powered equipment such as compressors, drilling rigs, pumps etc.[37] Also transportation of necessary water volume for hydraulic fracturing, if done by trucks, can cause high volumes of air emissions, especially particulate matter emissions.[78]
Shale gas produced by hydraulic fracturing causes higher well-to-burner emissions than conventional gas. This is mainly due to the gas released during completing wells as some gas returns to the surface, together with the fracturing fluids. Depending on their treatment, the well-to-burner emissions are 3.5%–12% higher than for conventional gas.[69] According to a study conducted by professor Robert W. Howarth et al. of Cornell University, "3.6% to 7.9% of the methane from shale-gas production escapes to the atmosphere in venting and leaks over the lifetime of a well." The study claims that this represents a 30–100% increase over conventional gas production.[79] Methane gradually breaks down in the atmosphere, forming carbon dioxide, which contributes to greenhouse gasses more than coal or oil for timescales of less than fifty years.[79][80] Howarth's colleagues at Cornell and others have criticized the study's design,[81][82] however several other studies have also found higher emissions from shale-gas production than from conventional gas production.[83][84][85][86] Howarth et al. have responded, "The latest EPA estimate for methane emissions from shale gas falls within the range of our estimates but not those of Cathles et al, which are substantially lower."[87]
In some areas, elevated air levels of harmful substances have coincided with elevated reports of health problems among the local populations. In DISH, Texas, elevated substance levels were detected and traced to hydraulic fracturing compressor stations,[88] and people living near shale gas drilling sites complained of health problems;[89] though a causal relationship to hydraulic fracturing was not established.[89]
Water
![]() | This article should be summarized in Environmental impact of hydraulic fracturing and a link provided from there to here using the {{Main}} template. (December 2012) |
Consumption
The large volumes of water required have raised concerns about hydraulic fracturing in arid areas, such as Karoo in South Africa.[70] During periods of low stream flow it may affect water supplies for municipalities and industries such as power generation, as well as recreation and aquatic life. It may also require water overland piping from distant sources.[90]
Hydraulic fracturing uses between 1.2 and 3.5 million US gallons (4.5 and 13.2 Ml) of water per well, with large projects using up to 5 million US gallons (19 Ml). Additional water is used when wells are refractured; this may be done several times.[44][91] An average well requires 3 to 8 million US gallons (11,000 to 30,000 m3) of water over its lifetime.[37][90][91][92] Using the case of the Marcellus Shale as an example, as of 2008 hydraulic fracturing accounted for 650 million US gallons per year (2,500,000 m3/a) or less than 0.8% of annual water use in the area overlying the Marcellus Shale.[90][93] The annual number of well permits, however, increased by a factor of five[94] and the number of well starts increased by a factor of over 17 from 2008 to 2011.[95] According to the Oxford Institute for Energy Studies, greater volumes of fracturing fluids are required in Europe, where the shale depths average 1.5 times greater than in the U.S.[96] To minimize water consumption, recycling is one possible option.[69]
Injected fluid
There are concerns about possible contamination by hydraulic fracturing fluid both as it is injected under high pressure into the ground and as it returns to the surface.[97] To mitigate the impact of hydraulic fracturing to groundwater, the well and ideally the shale formation itself should remain hydraulically isolated from other geological formations, especially freshwater aquifers.[69] In the United States at least 36 cases of groundwater contamination due to hydraulic fracturing have been suspected and in several cases EPA has determined that hydraulic fracturing was likely the source of the contamination.[77][98][99][100][101][102]
While some of the chemicals used in hydraulic fracturing are common and generally harmless, some are known carcinogens at high enough doses.[49] A report prepared for House Democratic members Henry Waxman, Edward Markey and Diana DeGette stated that out of 2,500 hydraulic fracturing products, "more than 650 of these products contained chemicals that are known or possible human carcinogens, regulated under the Safe Drinking Water Act, or listed as hazardous air pollutants".[49] The report also shows that between 2005 and 2009, 279 products had at least one component listed as "proprietary" or "trade secret" on their Occupational Safety and Health Administration (OSHA) required material safety data sheet (MSDS). The MSDS is a list of chemical components in the products of chemical manufacturers, and according to OSHA, a manufacturer may withhold information designated as "proprietary" from this sheet. When asked to reveal the proprietary components, most companies participating in the investigation were unable to do so, leading the committee to surmise these "companies are injecting fluids containing unknown chemicals about which they may have limited understanding of the potential risks posed to human health and the environment".[49] Without knowing the identity of the proprietary components, regulators cannot test for their presence. This prevents government regulators from establishing baseline levels of the substances prior to hydraulic fracturing and documenting changes in these levels, thereby making it more difficult to prove that hydraulic fracturing is contaminating the environment with these substances.[103]
Another 2011 study identified 632 chemicals used in natural gas operations. Only 353 of these are well-described in the scientific literature. The study indicated possible long-term health effects that might not appear immediately. The study recommended full disclosure of all products used, along with extensive air and water monitoring near natural gas operations; it also recommended that hydraulic fracturing's exemption from regulation under the US Safe Drinking Water Act be rescinded.[104]
Flowback
As the fracturing fluid flows back through the well, it consists of spent fluids and may contain dissolved constituents such as minerals and brine waters. It may account for about 30–70% of the original fracture fluid volume. In addition, natural formation waters may flow to the well and need treatment. These fluids, commonly known as flowback, produced water, or wastewater, are managed by underground injection, wastewater treatment and discharge, or recycling to fracture future wells.[105] Hydraulic fracturing can concentrate levels of uranium, radium, radon, and thorium in flowback. [106]. Treatment of produced waters may be feasible through either self-contained systems at well sites or fields or through municipal waste water treatment plants or commercial treatment facilities.[105] However, the quantity of waste water needing treatment and the improper configuration of sewage plants have become an issue in some regions of the United States. Much of the wastewater from hydraulic fracturing operations is processed by public sewage treatment plants, which are not equipped to remove radioactive material and are not required to test for it.[107] More problematic may be the high levels of Bromide released into the rivers. The Bromide in the water combines with chlorine, which is used to disinfect drinking water at water treatment plants, and forms trihalomethanes (THMs).[108]
Methane
Groundwater methane contamination is also a concern as it has adverse impact on water quality and in extreme cases may lead to potential explosion.[109][110] In 2006, over 7 million cubic feet (200,000 m3) of methane were released from a blown gas well in Clark, Wyoming and shallow groundwater was found to be contaminated.[111] However, methane contamination is not always caused by hydraulic fracturing. Drilling for ordinary drinking water wells can also cause methane release. Some studies make use of tests that can distinguish between the deep thermogenic methane released during gas/oil drilling, and the shallower biogenic methane that can be released during water-well drilling. While both forms of methane result from decomposition, thermogenic methane results from geothermal assistance deeper underground.[112][113]
According to the 2011 study of the MIT Energy Initiative, "there is evidence of natural gas (methane) migration into freshwater zones in some areas, most likely as a result of substandard well completion practices i.e. poor quality cementing job or bad casing, by a few operators."[114] 2011 studies by the Colorado School of Public Health and Duke University also pointed to methane contamination stemming from hydraulic fracturing or its surrounding process.[109][113] A study by Cabot Oil and Gas examined the Duke study using a larger sample size, found that methane concentrations were related to topography, with the highest readings found in low-lying areas, rather than related to distance from gas production areas. Using a more precise isotopic analysis, they showed that the methane found in the water wells came from both the Marcellus Shale (Middle Devonian) where hydraulic fracturing occurred, and from the shallower Upper Devonian formations.[112]
Radioactivity
A study examining a number of hydraulic fracturing sites in Pennsylvania and Virginia by Pennsylvania State University, found that water that flows back from gas wells after hydraulic fracturing contains high levels of radium.[115] Recycling this wastewater has been proposed as a partial solution, but this approach has limitations.[116] The New York Times has reported radium in wastewater from natural gas wells is released into Pennsylvania rivers,[110] and has compiled a map of these wells and their wastewater contamination levels,[117] and stated that some EPA reports were never made public. The Times' reporting on the issue has come under some criticism.[118][119]
Seismicity
Hydraulic fracturing causes induced seismicity called microseismic events or microearthquakes. The magnitude of these events is usually too small to be detected at the surface, although the biggest micro-earthquakes may have the magnitude of about -1.6 (Mw). The injection of waste water from gas operations, including from hydraulic fracturing, into saltwater disposal wells may cause bigger low-magnitude tremors, being registered up to 3.3 (Mw).[120]
The United States Geological Survey (USGS) has reported earthquakes induced by human measures, including hydraulic fracturing and hydraulic fracturing waste disposal wells, in several locations. According to the USGS only a small fraction of roughly 40,000 waste fluid disposal wells for oil and gas operations have induced earthquakes that are large enough to be of concern to the public.[121] Although the magnitudes of these quakes has been small, the USGS says that there is no guarantee that larger quakes will not occur.[122] In addition, the frequency of the quakes has been increasing. In 2009, there were 50 earthquakes greater than magnitude-3.0 in the area spanning Alabama and Montana, and there were 87 quakes in 2010. In 2011 there were 134 earthquakes in the same area, a sixfold increase over 20th century levels.[123] There are also concerns that quakes may damage underground gas, oil, and water lines and wells that were not designed to withstand earthquakes.[122][124]
A British Columbia Oil and Gas Commission investigation concluded that a series of 38 earthquakes (magnitudes ranging from 2.2 to 3.8 on the Richter scale) occurring in the Horn River Basin area between 2009 and 2011 were caused by fluid injection during hydraulic fracturing in proximity to pre-existing faults.[125] A report in the UK also concluded that hydraulic fracturing was the likely cause of some small tremors that occurred during shale gas drilling.[126][127][128]
Several earthquakes occurring throughout 2011, including a 4.0 magnitude quake on New Year's Eve that hit Youngstown, Ohio, are likely linked to a disposal of hydraulic fracturing wastewater, according to seismologists at Columbia University.[129] A similar series of small earthquakes occurred in 2012 in Texas. Earthquakes are not common occurrences in either area. Disposal and injection wells are regulated under the Safe Drinking Water Act and UIC laws.[130]
Health impact
Concern has been expressed over the possible long and short term health effects of air and water contamination and radiation exposure by gas production.[131][132][106] The number of unconventional natural gas wells in the US rose from 18,485 in 2004 to 25,145 in 2007 and is expected to continue increasing through at least 2020. [133] While groundwater contamination and radiation exposure are important considerations, the cumulative impacts of tens of thousands of wells on regional air quality should be considered. Emissions from flowback operations, which may include emissions from various sources on the well pads, such as the wells themselves and diesel engines, are likely the major sources of the hydrocarbons observed in well completion samples. [132][134]
Multiple studies on inhalation exposure to petroleum hydrocarbons in occupational settings as well as residences near refineries, oil spills and petrol stations indicate an increased risk of eye irritation and headaches, asthma symptoms, acute childhood leukemia, acute myelogenous leukemia, and multiple myeloma. [135] Many of the petroleum hydrocarbons observed in these studies are present in and around NGD sites. [136] Benzene, a known carcinogen, is one of the many hydrocarbons released during flowback. [132] The known health effects of benzene include acute and chronic acute and chronic nonlymphocytic leukemia, acute myeloid leukemia, chronic lymphocytic leukemia, anemia, and other blood disorders and immunological effects. [137] In addition, maternal exposure to ambient levels of benzene recently has been associated with an increase in birth prevalence of neural tube defects. [138] Based on these health effects, risk prevention efforts should be directed towards reducing air emission exposures for persons living and working near wells during well completions. [134] Public health officials can have the most impact on protecting the public's health by minimizing exposures for those living closet the well pads. They can protect them by controlling and monitoring emissions during completion and transitions and flowback, capturing and reducing emissions through use of low or no emmission flowback tanks, and establishing and maintaing communication regarding well pad activities with the community. [132]
In the United States the Occupational Safety and Health Administration (OSHA) and the National Institute for Occupational Safety and Health (NIOSH) have released a hazard alert based on data collected by NIOSH that workers may be exposed to dust with high levels of respirable crystalline silica (silica dioxide) during hydraulic fracturing.[139] NIOSH notified company representatives of these findings and provided reports with recommendations to control exposure to crystalline silica and recommend that all hydraulic fracturing sites evaluate their operations to determine the potential for worker exposure to crystalline silica and implement controls as necessary to protect workers.[140]
Public debate
Politics and public policy
To control the hydraulic fracturing industry, some governments are developing legislation and some municipalities are developing local zoning limitations.[141] In 2011, France became the first nation to ban hydraulic fracturing.[6][7] Some other countries have placed a temporary moratorium on the practice.[142] The US has the longest history with hydraulic fracturing, so its approaches to hydraulic fracturing may be modeled by other countries.[70]
The considerable opposition against hydraulic fracturing activities in local townships has led companies to adopt a variety of public relations measures to assuage fears about hydraulic fracturing, including the admitted use of "military tactics to counter drilling opponents". At a conference where public relations measures were discussed, a senior executive at Anadarko Petroleum was recorded on tape saying, "Download the US Army / Marine Corps Counterinsurgency Manual, because we are dealing with an insurgency", while referring to hydraulic fracturing opponents. Matt Pitzarella, spokesman for Range Resources also told other conference attendees that Range employed psychological warfare operations veterans. According to Pitzarella, the experience learned in the Middle East has been valuable to Range Resources in Pennsylvania, when dealing with emotionally charged township meetings and advising townships on zoning and local ordinances dealing with hydraulic fracturing.[143][144]
Media coverage
Josh Fox's 2010 film Gasland became a center of opposition to hydraulic fracturing of shale. The movie presented problems with ground water contamination near well sites in Pennsylvania, Wyoming, and Colorado.[145] Energy in Depth, an oil and gas industry lobbying group, called the film's facts into question.[146] In response, a rebuttal of Energy in Depth's claims of inaccuracy was posted on Gasland's website.[147] The Director of the Colorado Oil and Gas Conservation Commission (COGCC) offered to be interviewed as part of the film if he could review what was included from the interview in the final film but Fox declined the offer. The COGCC took issue with what it called "several errors" in the film after its production.[148] The Independent Petroleum Association of America later produced its own documentary, Truthland.[149] Exxon Mobil, Chevron Corporation and ConocoPhillips also aired advertisements during 2011 and 2012 that describe the economic and environmental benefits of natural gas and argue hydraulic fracturing is safe.[149] The film Promised Land, starring Matt Damon, takes on hydraulic fracturing.[150] The gas industry has made plans to counter the film's criticisms of hydraulic fracturing with informational flyers, and Twitter and Facebook posts.[149]
One New York Times report claimed that an early draft of a 2004 EPA study discussed "possible evidence" of aquifer contamination but the final report omitted that mention.[71] Some have criticized the narrowing of EPA studies, including the EPA study on hydraulic fracturing's impact on drinking water to be released in late 2014,[151] such that hydrocarbon extraction processes not unique to hydraulic fracturing, such as drilling, casing, and above ground impacts, are considered beyond scope.[72][74][152][153][154]
See also
- Directional drilling
- Environmental concerns with electricity generation
- Environmental impact of petroleum
- Environmental impact of the oil shale industry
- ExxonMobil Electrofrac
- Hydraulic fracturing by country
- Hydraulic fracturing in the United States
- Natural gas
- Shale gas
References
- ^ a b c Charlez, Philippe A. (1997). Rock Mechanics: Petroleum Applications. Paris: Editions Technip. p. 239. ISBN 9782710805861. Retrieved 2012-05-14.
- ^ a b "US Government Role in Shale Gas Fracking: An Overview"
- ^ a b SPE production & operations. Vol. 20. Society of Petroleum Engineers. 2005. p. 87.
- ^ a b c IEA (29 May 2012). Golden Rules for a Golden Age of Gas. World Energy Outlook Special Report on Unconventional Gas (PDF). OECD. pp. 18–27.
- ^ a b Brown, Valerie J. (February 2007). "Industry Issues: Putting the Heat on Gas". Environmental Health Perspectives. 115 (2). US National Institute of Environmental Health Sciences: A76. doi:10.1289/ehp.115-a76. PMC 1817691. PMID 17384744. Retrieved 2012-05-01.
- ^ a b Patel, Tara (31 March 2011). "The French Public Says No to 'Le Fracking'". Bloomberg Businessweek. Retrieved 22 February 2012.
- ^ a b Patel, Tara (4 October 2011). "France to Keep Fracking Ban to Protect Environment, Sarkozy Says". Bloomberg Businessweek. Retrieved 22 February 2012.
- ^ Fjaer, E. (2008). "Mechanics of hydraulic fracturing". Petroleum related rock mechanics. Developments in petroleum science (2 ed.). Elsevier. p. 369. ISBN 978-0-444-50260-5. Retrieved 2012-05-14.
- ^ Price, N.J.; Cosgrove, J.W. (1990). Analysis of geological structures. Cambridge University Press. pp. 30–33. ISBN 978-0-521-31958-4. Retrieved 5 November 2011.
- ^ Manthei, G.; Eisenblätter, J.; Kamlot, P. (2003). "Stress measurement in salt mines using a special hydraulic fracturing borehole tool". In Natau, Fecker & Pimentel (ed.). Geotechnical Measurements and Modelling (PDF). pp. 355–360. ISBN 90-5809-603-3. Retrieved 6 March 2012.
- ^ Zoback, M.D. (2007). Reservoir geomechanics. Cambridge University Press. p. 18. ISBN 9780521146197. Retrieved 6 March 2012.
- ^ Laubach, S.E. (2004). "Coevolution of crack-seal texture and fracture porosity in sedimentary rocks: cathodoluminescence observations of regional fractures". Journal of Structural Geology. 26 (5). Elsevier: 967–982. Bibcode:2004JSG....26..967L. doi:10.1016/j.jsg.2003.08.019. Retrieved 5 November 2011.
{{cite journal}}
: Unknown parameter|coauthors=
ignored (|author=
suggested) (help) - ^ Sibson, R.H.; =Moore, J.; Rankin, A.H. (1975). "Seismic pumping--a hydrothermal fluid transport mechanism". Journal of the Geological Society. 131 (6). London: Geological Society: 653–659. doi:10.1144/gsjgs.131.6.0653. (subscription required). Retrieved 5 November 2011.
{{cite journal}}
: CS1 maint: extra punctuation (link) - ^ Gill, R. (2010). Igneous rocks and processes: a practical guide. John Wiley and Sons. p. 102. ISBN 978-1-4443-3065-6. Retrieved 5 November 2011.
- ^ a b c Montgomery, Carl T.; Smith, Michael B. (2010-12-105). "Hydraulic fracturing. History of an enduring technology" (PDF). JPT Online. Society of Petroleum Engineers: 26–41. Retrieved 13 May 2012.
{{cite journal}}
: Check date values in:|date=
(help) - ^ Energy Institute (2012). Fact-Based Regulation for Environmental Protection in Shale Gas Development (PDF) (Report). University of Texas at Austin. Retrieved 29 February 2012.
{{cite report}}
: Unknown parameter|month=
ignored (help) - ^ Mader, Detlef (1989). Hydraulic Proppant Fracturing and Gravel Packing. Elsevier. pp. 173–174, 202. ISBN 9780444873521.
- ^ United States National Research Council, Committee to Review the Gas Research Institute's Research, Development and Demonstration Program, Gas Research Institute (1989). A review of the management of the Gas Research Institute. National Academies. p. ?.
{{cite book}}
: CS1 maint: multiple names: authors list (link) - ^ The Breakthrough Institute. Interview with Dan Steward, former Mitchell Energy Vice President. December 2011.
- ^ Wasley, Andrew (1 March 2013) On the frontline of Poland's fracking rush The Guardian, Retrieved 3 March 2013
- ^ (7 August 2012) JKX Awards Fracking Contract for Ukrainian Prospect Natural Gas Europe, Retrieved 3 March 2013
- ^ (18 February 2013) Turkey's shale gas hopes draw growing interest Reuters, Retrieved 3 March 2013
- ^ "Hydraulic fracturing research study" (PDF). EPA. 2010. EPA/600/F-10/002. Retrieved 2012-12-26.
{{cite web}}
: Unknown parameter|month=
ignored (help) - ^ "The Barnett Shale" (PDF). North Keller Neighbors Together. Retrieved 2012-05-14.
- ^ David Wethe (19 January 2012). "Like Fracking? You'll Love 'Super Fracking'". Businessweek. Retrieved 22 January 2012.
- ^ "Production Decline of a Natural Gas Well Over Time". Geology.com. The Geology Society of America. 3 January 2012. Retrieved 4 March 2012.
- ^ Gidley, John L. (1989). Recent Advances in Hydraulic Fracturing. SPE Monograph. Vol. 12. SPE. p. ?. ISBN 9781555630201.
- ^ Ching H. Yew (1997). Mechanics of Hydraulic Fracturing. Gulf Professional Publishing. p. ?. ISBN 9780884154747.
- ^ a b Economides, Michael J. (2000). Reservoir stimulation. J. Wiley. p. P-2. ISBN 9780471491927.
- ^ Banks, David (1996). "Permeability and stress in crystalline rocks". Terra Nova. 8 (3): 223–235. doi:10.1111/j.1365-3121.1996.tb00751.x.
{{cite journal}}
: Unknown parameter|coauthors=
ignored (|author=
suggested) (help); Unknown parameter|month=
ignored (help) - ^ Brown, Edwin Thomas (2007) [2003]. Block Caving Geomechanics (2nd ed.). Indooroopilly, Queensland: Julius Kruttschnitt Mineral Research Centre, UQ. ISBN 978-0-9803622-0-6. Retrieved 2012-05-14.
- ^ Frank, U.; Barkley, N. (February 1995). "Remediation of low permeability subsurface formations by fracturing enhancement of soil vapor extraction". Journal of Hazardous Materials. 40 (2): 191–201. doi:10.1016/0304-3894(94)00069-S. ISSN 0304-3894. (subscription required).
{{cite journal}}
: More than one of|work=
and|journal=
specified (help) - ^ Bell, Frederic Gladstone (2004). Engineering Geology and Construction. Taylor & Francis. p. 670. ISBN 9780415259392.
- ^ Aamodt, R. Lee; Kuriyagawa, Michio (1983). "Measurement of Instantaneous Shut-In Pressure in Crystalline Rock". Hydraulic fracturing stress measurements. National Academies. p. 139.
- ^ "Geothermal Technologies Program: How an Enhanced Geothermal System Works". .eere.energy.gov. 2011-02-16. Retrieved 2011-11-02.
- ^ Miller, Bruce G. (2005). Coal Energy Systems. Sustainable World Series. Academic Press. p. 380. ISBN 9780124974517.
- ^ a b c d e f g h i Ground Water Protection Council; ALL Consulting (2009). Modern Shale Gas Development in the United States: A Primer (PDF) (Report). DOE Office of Fossil Energy and National Energy Technology Laboratory. pp. 56–66. DE-FG26-04NT15455. Retrieved 24 February 2012.
{{cite report}}
: Unknown parameter|month=
ignored (help) - ^ Penny, Glenn S.; Conway, Michael W.; Lee, Wellington (1985). "Control and Modeling of Fluid Leakoff During Hydraulic Fracturing". Journal of Petroleum Technology. 37 (6). Society of Petroleum Engineers: 1071–1081. doi:10.2118/12486-PA. Retrieved 2012-05-10.
{{cite journal}}
: Unknown parameter|month=
ignored (help) - ^ Arthur, J. Daniel; Bohm, Brian; Coughlin, Bobbi Jo; Layne, Mark (2008). Hydraulic Fracturing Considerations for Natural Gas Wells of the Fayetteville Shale (PDF) (Report). ALL Consulting. p. 10. Retrieved 2012-05-07.
- ^ Chilingar, George V.; Robertson, John O.; Kumar, Sanjay (1989). Surface Operations in Petroleum Production. Vol. 2. Elsevier. pp. 143–152. ISBN 9780444426772.
- ^ Love, Adam H. (2005). "Fracking: The Controversy Over its Safety for the Environment". Johnson Wright, Inc. Retrieved 2012-06-10.
{{cite web}}
: Unknown parameter|month=
ignored (help) - ^ "Hydraulic Fracturing". University of Colorado Law School. Retrieved 2 June 2012.
- ^ Wan Renpu (2011). Advanced Well Completion Engineering. Gulf Professional Publishing. p. 424. ISBN 9780123858689.
- ^ a b c d e Andrews, Anthony; et al. (30 October 2009). Unconventional Gas Shales: Development, Technology, and Policy Issues (PDF) (Report). Congressional Research Service. p. 7; 23. Retrieved 22 February 2012.
{{cite report}}
: Explicit use of et al. in:|author=
(help) - ^ Ram Narayan (August 8, 2012). "From Food to Fracking: Guar Gum and International Regulation". RegBlog. University of Pennsylvania Law School. Retrieved 15 August 2012.
- ^ Hartnett-White, K. (2011). "The Fracas About Fracking- Low Risk, High Reward, but the EPA is Against it" (PDF). National Review Online. Retrieved 2012-05-07.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ a b c d e f g h i j "Freeing Up Energy. Hydraulic Fracturing: Unlocking America's Natural Gas Resources" (PDF). American Petroleum Institute. 2010-07-19. Retrieved 2012-12-29.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ "CARBO ceramics". Retrieved 2011.
{{cite web}}
: Check date values in:|accessdate=
(help) - ^ a b c d e Chemicals Used in Hydraulic Fracturing (PDF) (Report). Committee on Energy and Commerce U.S. House of Representatives. April 18, 2011. p. ?.
- ^ a b ALL Consulting (2012). The Modern Practices of Hydraulic Fracturing: A Focus on Canadian Resources (PDF) (Report). Canadian Association of Petroleum Producers. Retrieved 2012-08-04.
{{cite report}}
: Unknown parameter|month=
ignored (help) - ^ Reis, John C. (1976). Environmental Control in Petroleum Engineering. Gulf Professional Publishers.
- ^ a b c Radiation Protection and the Management of Radioactive Waste in the Oil and Gas Industry (PDF) (Report). International Atomic Energy Agency. 2003. pp. 39–40. Retrieved 20 May 2012.
Beta emitters including H-3 and C-14 may be used when it is feasible to use sampling techniques to detect the presence of the radiotracer or when changes in activity concentration can be used as indicators of the properties of interest in the system. Gamma emitters, such as Sc-46, La-140, Mn-56, Na-24, Sb-124, Ir-192, Tc-m, I-131, Ag-m, Ar-41, and Xe-133 are used extensively because of the ease with which they can be identified and measured ... In order to aid the detection of any spillage of solutions of the 'soft' beta emitters, they are sometimes spiked with a short half-life gamma emitter such as Br-82
- ^ a b Jack E. Whitten, Steven R. Courtemanche, Andrea R. Jones, Richard E. Penrod, and David B. Fogl (Division of Industrial and Medical Nuclear Safety, Office of Nuclear Material Safety and Safeguards) (June 2000). "Consolidated Guidance About Materials Licenses: Program-Specific Guidance About Well Logging, Tracer, and Field Flood Study Licenses (NUREG-1556, Volume 14)". US Nuclear Regulatory Commission. Retrieved 19 April 2012.
labeled Frac Sand...Sc-46, Br-82, Ag-110m, Sb-124, Ir-192
{{cite web}}
: CS1 maint: multiple names: authors list (link) - ^ Bennet, Les; et al. "The Source for Hydraulic Fracture Characterization" (PDF). Oilfield Review (Winter 2005/2006). Schlumberger: 42–57. Retrieved 2012-09-30.
{{cite journal}}
: Explicit use of et al. in:|author=
(help) - ^ Seale, Rocky (2007). "Open hole completion systems enables multi-stage fracturing and stimulation along horizontal wellbores" (PDF). Drilling Contractor (Fracturing stimulation ed.). Retrieved October 1, 2009.
{{cite journal}}
: Unknown parameter|month=
ignored (help) - ^ "Completion Technologies". EERC. Retrieved 2012-09-30.
- ^ [energyfromshale.org "EnergyFromShale"]. EnergyFromShale. 2011.
{{cite web}}
: Check|url=
value (help) - ^ Mooney, Chris (2011). "The Truth About Fracking". Scientific American. 305 (305): 80–85. Bibcode:2011SciAm.305d..80M. doi:10.1038/scientificamerican1111-80.
- ^ Clayton, Mark (27 February 2013). "Exclusive: Cyberattack leaves natural gas pipelines vulnerable to sabotage. A government report says a cyberattack against 23 natural gas pipeline operators stole crucial information that could compromise security. Experts strongly suspect China's military". Christian Science Monitor. Retrieved 3 March 2013.
The cyberspies are aiming mainly at stealing technology related to hydraulic fracturing or "fracking" of shale to extract natural gas, says Mr. Huber of Critical Intelligence. Stealing industrial secrets about fracking could help energy-starved China develop its own technologies to mine natural gas without having to buy equipment or expertise from abroad.
- ^ National Petroleum Council, Prudent Development: Realizing the Potential of North America’s Abundant Natural Gas and Oil Resources, September 15, 2011.
- ^ IHS Global Insight, Measuring the Economic and Energy Impacts of Proposals to Regulate Hydraulic Fracturing, 2009.
- ^ IHS Global Insight, The Economic and Employment Contributions of Shale Gas in the United States, December 2011.
- ^ American Chemistry Council, Shale Gas and New Petrochemicals Investment: Benefits for the Economy, Jobs, and U.S. Manufacturing, March 2011.
- ^ PriceWaterhouseCoopers, A Renaissance in Shale Gas? December 2011.
- ^ IHS Global Insight, The Economic and Employment Contributions of Natural Gas in the United States, December 2011.
- ^ Obel, Mike (1 March 2013). "Potential Surge Of US LNG Exports From Shale Natural Gas Boom Splits Corporate America; One Side Gets Allied With Environmentalists". International Business Times. Retrieved 3 March 2013.
...the boom in production has created a rare fissure that runs through the heart of corporate America, pitting manufacturers such as Dow Chemical against energy giants such as the Exxon Mobil Corp. (NYSE:XOM), which have been seeking to raise the price of natural gas by pushing the government to allow them to export to more countries. That concerns manufacturers, which warn that such an export-heavy policy will result in higher energy prices in the U.S. and hurt manufacturing.
- ^ Tucker, Aviza (19 December 2012) The New Power Map Foreign Affairs, published by the Council on Foreign Relations, Retrieved 22 February 2013
- ^ a b c d e Barth, J.M. (2013) The economic impact of shale gas on state and local economies: Benefits, costs, and uncertainties. New Solutions: A Journal of Environmental and Occupational Health Policy, 23(1), 85-102
- ^ a b c d IEA (2011). World Energy Outlook 2011. OECD. pp. 91, 164. ISBN 9789264124134.
- ^ a b c Urbina, Ian (30 December 2011). "Hunt for Gas Hits Fragile Soil, and South Africans Fear Risks". The New York Times. Retrieved 23 February 2012.
Covering much of the roughly 800 miles between Johannesburg and Cape Town, this arid expanse – its name [Karoo] means "thirsty land" – sees less rain in some parts than the Mojave Desert.
- ^ a b c Urbina, Ian (3 March 2011). "Pressure Limits Efforts to Police Drilling for Gas". The New York Times. Retrieved 23 February 2012.
More than a quarter-century of efforts by some lawmakers and regulators to force the federal government to police the industry better have been thwarted, as E.P.A. studies have been repeatedly narrowed in scope and important findings have been removed
- ^ a b DiCosmo, Bridget (15 May 2012). "SAB Pushes To Advise EPA To Conduct Toxicity Tests In Fracking Study". InsideEPA. Inside Washington Publishers. (subscription required). Retrieved 2012-05-19.
But some members of the chartered SAB are suggesting that the fracking panel revise its recommendation that the agency scale back its planned toxicity testing of chemicals used in the hydraulic fracturing, or fracking, process, because of the limited resources and time frame ... Chesapeake Energy supported the draft recommendation, saying that "an in-depth study of toxicity, the development of new analytical methods and tracers are not practical given the budget and schedule limitation of the study."
- ^ Satterfield, John (30 June 2011). "Letter from Chesapeake Energy to EPA" (Document). Inside Washington Publishers. (subscription required).
Flowback and Produced water ... Chesapeake agrees that an indepth study of toxicity, the development of new analytic methods and tracers are not practical given the budget and schedule limitations of the study ... Wastewater Treatment and Waste Disposal ... Chesapeake believes there was unjustified emphasis on the surface disposal of produced water to treatment plants in the SAB's Review ... Chesapeake disagrees with the inclusion of water distribution network corrosion and burden of analyzing for contaminants by POTW's into the study.
{{cite document}}
: Unknown parameter|accessdate=
ignored (help); Unknown parameter|format=
ignored (help); Unknown parameter|newspaper=
ignored (help); Unknown parameter|url=
ignored (help) - ^ a b "The Debate Over the Hydrofracking Study's Scope". The New York Times. 3 March 2011. Retrieved 1 May 2012.
While environmentalists have aggressively lobbied the agency to broaden the scope of the study, industry has lobbied the agency to narrow this focus
- ^ "Natural Gas Documents". The New York Times. 27 February 2011. Retrieved 5 May 2012.
The Times reviewed more than 30,000 pages of documents obtained through open records requests of state and federal agencies and by visiting various regional offices that oversee drilling in Pennsylvania. Some of the documents were leaked by state or federal officials.
- ^ Ramanuja, Krishna (7 Martch 2012). "Study suggests hydrofracking is killing farm animals, pets". Cornell Chronicle. Cornell University. Retrieved 9 March 2012.
{{cite news}}
: Check date values in:|date=
(help) - ^ a b Urbina, Ian (3 August 2011). "A Tainted Water Well, and Concern There May be More". The New York Times. Retrieved 22 February 2012.
- ^ Fernandez, John Michael; Gunter, Matthew. "Hydraulic Fracturing: Environmentally Friendly Practices" (PDF). Houston Advanced Research Center. Retrieved 2012-12-29.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ a b Howarth, Robert W.; Santoro, Renee; Ingraffea, Anthony (13 March 2011). "Methane and the greenhouse-gas footprint of natural gas from shale formations" (PDF). Climatic Change. 106 (4). Springer: 679–690. doi:10.1007/s10584-011-0061-5. Retrieved 2012-05-07.
- ^ Howarth, Robert W.; Ingraffea, Anthony; Engelder, Terry (15 September 2011). "Should Fracking Stop? Extracting gas from shale increases the availability of this resource, but the health and environmental risks may be too high. Point: Yes, it's too high risk". Nature. 477 (477): 271–275. Bibcode:2011Natur.477..271H. doi:10.1038/477271a.
- ^ Cathles, Lawrence M.; Brown, Larry; Taam, Milton; Hunter, Andrew (2011). "A commentary on "The greenhouse-gas footprint of natural gas in shale formations" by R.W. Howarth, R. Santoro, and Anthony Ingraffea". Climatic Change. 113 (2): 525. doi:10.1007/s10584-011-0333-0.
- ^ Leahy, Stephen (24 January 2012). "Shale Gas a Bridge to More Global Warming". IPS. Retrieved 4 February 2012.
- ^ Skone, Timothy J. (12 May 2011). "Life Cycle Greenhouse Gas Analysis of Natural Gas Extraction & Delivery in the United States" (PDF). National Energy Technology Laboratory. Retrieved 4 February 2012.
- ^ Jiang, Mohan; Griffin, W Michael; Hendrickson, Chris; Jaramillo, Paulina; VanBriesen, Jeanne; Venkatesh, Aranya (2011). "Life cycle greenhouse gas emissions of Marcellus shale gas" (PDF). Environmental Research Letters. 6 (3). IOP Publishing: 034014. Bibcode:2011ERL.....6c4014J. doi:10.1088/1748-9326/6/3/034014. Retrieved 4 February 2012.
- ^ Hultman, Nathan; Rebois, Dylan; Scholten, Michael; Ramig, Christopher (2011). "The greenhouse impact of unconventional gas for electricity generation" (PDF). Environmental Research Letters. 6 (4). IOP Publishing: 044008. Bibcode:2011ERL.....6d4008H. doi:10.1088/1748-9326/6/4/044008. Retrieved 4 February 2012.
- ^ Lashof, Dan (12 April 2011). "Natural Gas Needs Tighter Production Practices to Reduce Global Warming Pollution". Natural Resources Defense Council. Retrieved 4 February 2012.
- ^ Howarth, Robert W.; Santoro, Renee; Ingraffea, Anthony (1 February 2012). "Venting and leaking of methane from shale gas development: Response to Cathles et al" (PDF). Climatic Change. 113 (2). Springer: 537. doi:10.1007/s10584-012-0401-0. Retrieved 4 February 2012.
- ^ Biello, David (30 March 2010). "Natural gas cracked out of shale deposits may mean the U.S. has a stable supply for a century – but at what cost to the environment and human health?". Scientific American. Retrieved 23 March 2012.
- ^ a b Schmidt, Charles (1 August 2011). "Blind Rush? Shale Gas Boom Proceeds Amid Human Health Questions". Environmental Health Perspectives. 119 (8): a348–a353. doi:10.1289/ehp.119-a348. PMC 3237379.
- ^ a b c Arthur, J. Daniel; Uretsky, Mike; Wilson, Preston (May 5–6, 2010). Water Resources and Use for Hydraulic Fracturing in the Marcellus Shale Region (PDF). Meeting of the American Institute of Professional Geologists. Pittsburgh: ALL Consulting. p. 3. Retrieved 2012-05-09.
- ^ a b Abdalla, Charles W.; Drohan, Joy R. (2010). Water Withdrawals for Development of Marcellus Shale Gas in Pennsylvania. Introduction to Pennsylvania’s Water Resources (PDF) (Report). The Pennsylvania State University. Retrieved 16 September 2012.
Hydrofracturing a horizontal Marcellus well may use 4 to 8 million gallons of water, typically within about 1 week. However, based on experiences in other major U.S. shale gas fields, some Marcellus wells may need to be hydrofractured several times over their productive life (typically five to twenty years or more)
- ^ Cothren, Jackson. Modeling the Effects of Non-Riparian Surface Water Diversions on Flow Conditions in the Little Red Watershed (PDF) (Report). U. S. Geological Survey, Arkansas Water Science Center Arkansas Water Resources Center, American Water Resources Association, Arkansas State Section Fayetteville Shale Symposium 2012. p. 12. Retrieved 16 September 2012.
...each well requires between 3 and 7 million gallons of water for hydraulic fracturing and the number of wells is expected to grow in the future
- ^ Satterfield, J; Mantell; Kathol, D; Hiebert, F; Patterson, K; Lee, R (September 2008). Managing Water Resource‘s Challenges in Select Natural Gas Shale Plays. GWPC Annual Meeting. ALL Consulting.
{{cite conference}}
:|access-date=
requires|url=
(help); Unknown parameter|first 2=
ignored (|first2=
suggested) (help) - ^ "Unconventional well drilling permits". Marcellus Center. Marcellus Center, Pennsylvania State University. 2012. Retrieved 2012-09-16.
- ^ "Horizontal drilling boosts Pennsylvania's natural gas production". EIA. 23 May 2012. Retrieved 2012-09-16.
- ^ Faucon, Benoît (17 September 2012). "Shale-Gas Boom Hits Eastern Europe". WSJ.com. Retrieved 17 September 2012.
- ^ "Drilling Down: Documents: Natural Gas's Toxic Waste". The New York Times. 26 February 2011. Retrieved 23 February 2012.
- ^ Mall, Amy (19 December 2011). "Incidents where hydraulic fracturing is a suspected cause of drinking water contamination". Switchboard: NRDC Staff Blog. Natural Resources Defense Council. Retrieved 23 February 2012.
- ^ Lustgarten, Abrahm (November 2008). "Incidents where hydraulic fracturing is a suspected cause of drinking water contamination". ProPublica. Retrieved 20 March 2012.
- ^ Phillips, Susan (8 December 2011). "EPA Blames Fracking for Wyoming Groundwater Contamination". StateImpact Pennsylvania. NPR. Retrieved 6 February 2012.
federal environmental regulators have made a direct link between the controversial drilling practice known as hydraulic fracturing and groundwater contamination...The EPA found high concentrations of benzene, xylene, gasoline and diesel fuel in shallow groundwater supplies that they linked to wastewater pits. But the report also found a number of fracking chemicals in much deeper fresh water wells.
{{cite web}}
: soft hyphen character in|quote=
at position 4 (help); soft hyphen character in|work=
at position 17 (help) - ^ Fetzer, Richard M. (19 January 2012). Action Memorandum — Request for funding for a Removal Action at the Dimock Residential Groundwater Site (PDF) (Report). Retrieved 27 May 2012.
- ^ DiGiulio, Dominic C.; Wilkin, Richard T.; Miller, Carlyle; Oberley, Gregory (2011). Investigation of Ground Water Contamination near Pavillion, Wyoming. Draft (PDF) (Report). EPA. Retrieved 23 March 2012.
{{cite report}}
: Unknown parameter|month=
ignored (help) - ^ Kris Fitz Patrick (November 17, 2011). "Ensuring Safe Drinking Water in the Age of Hydraulic Fracturing".
The most fundamental recommendation is for states to rigorously test their ground water before and after hydraulic fracturing takes place. A major difficulty in proving or disproving contamination in previous cases has been the lack of a baseline sample for the water supply in question. The group also raises a federal policy issue, namely whether fracturing fluids should continue to be exempt from Safe Drinking Water Act regulations. This exemption was an informal one until 2005, when it was codified as part of the Energy Policy Act. A consequence of this exemption is that drilling companies are not required to disclose the chemicals that make up the fracturing fluids, making testing for these chemicals in ground water more difficult.
- ^ Colborn, Theo; Kwiatkowski, Carol; Schultz, Kim; Bachran, Mary (2011). "Natural Gas Operations from a Public Health Perspective" (PDF). Human and Ecological Risk Assessment: an International Journal. 17 (5). Taylor & Francis: 1039–1056. doi:10.1080/10807039.2011.605662.
- ^ a b Arthur, J. Daniel; Langhus, Bruce; Alleman, David (2008). An overview of modern shale gas development in the United States (PDF) (Report). ALL Consulting. p. 21. Retrieved 2012-05-07.
- ^ a b Weinhold, Bob (19 September 2012). "Unknown Quantity: Regulating Radionuclides in Tap Water". Environmental Health Perspectives. NIEHS, NIH. Retrieved 11 February 2012.
Examples of human activities that may lead to radionuclide exposure include mining, milling, and processing of radioactive substances; wastewater releases from the hydraulic fracturing of oil and natural gas wells...Mining and hydraulic fracturing, or "fracking," can concentrate levels of uranium (as well as radium, radon, and thorium) in wastewater..
{{cite web}}
: soft hyphen character in|quote=
at position 117 (help) - ^ Caruso, David B. (2011-01-03). "44,000 Barrels of Tainted Water Dumped Into Neshaminy Creek. We're the only state allowing tainted water into our rivers". NBC Philadelphia. Associated Press. Retrieved 2012-04-28.
...the more than 300,000 residents of the 17 municipalities that get water from the creek or use it for recreation were never informed that numerous public pronouncements that the watershed was free of gas waste had been wrong.
- ^ Bruce Gellerman and Ann Murray (10 August 2012). "Disposal of Fracking Wastewater Polluting PA Rivers". PRI's Environmental News Magazine. Public Radio International. Retrieved 14 January 2013.
- ^ a b Osborn, Stephen G.; Vengosh, Avner; Warner, Nathaniel R.; Jackson, Robert B. (2011-05-17). "Methane contamination of drinking water accompanying gas-well drilling and hydraulic fracturing" (PDF). Proceedings of the National Academy of Sciences of the United States of America. 108 (20): 8172–8176. doi:10.1073/pnas.1100682108. Retrieved 2011-10-14.
- ^ a b Urbina, Ian (26 February 2011). "Regulation Lax as Gas Wells' Tainted Water Hits Rivers". The New York Times. Retrieved 22 February 2012.
- ^ Blowout brings scrutiny to energy company
- ^ a b Molofsky, L.J.; Connor, J.A.; Shahla, K.F.; Wylie, A.S.; Wagner, T. (December 5, 2011). "Methane in Pennsylvania Water Wells Unrelated to Marcellus Shale Fracturing". Oil and Gas Journal. 109 (49). Pennwell Corporation: 54–67.
- ^ a b "Gasland Correction Document" (PDF). Colorado Oil & Gas Conservation Commission. Retrieved 25 January 2012.
- ^ Moniz, Ernest J.; et al. (2011). The Future of Natural Gas: An Interdisciplinary MIT Study (PDF) (Report). Massachusetts Institute of Technology. Retrieved 1 June 2012.
{{cite report}}
: Explicit use of et al. in:|author=
(help); Unknown parameter|month=
ignored (help) - ^ "Analysis of Marcellus flowback finds high levels of ancient brines" (Press release). Pennsylvania State University. 17 December 2012. Retrieved 31 January 2013.
- ^ Urbina, Ian (1 March 2011). "Drilling Down: Wastewater Recycling No Cure-All in Gas Process". The New York Times. Retrieved 22 February 2012.
- ^ White, Jeremy; Park, Haeyoun; Urbina, Ian; Palmer, Griff (26 February 2011). "Toxic Contamination From Natural Gas Wells". The New York Times.
- ^ "Natural Gas Drilling, the Spotlight". The New York Times. 5 March 2011. Retrieved 24 February 2012.
- ^ Petit], Charles (2 March 2011). "Part II of the fracking water problems in PA and other Marcellus Shale country". Knight Science Journalism Tracker. MIT. Retrieved 24 February 2012.
- ^ Zoback, Mark; Kitasei, Saya; Copithorne, Brad (2010). Addressing the Environmental Risks from Shale Gas Development (PDF) (Report). Worldwatch Institute. p. 9. Retrieved 2012-05-24.
{{cite report}}
: Unknown parameter|month=
ignored (help) - ^ "FAQs – Earthquakes Induced by Fluid Injection". USGS. 25 June 2012. Retrieved 4 November 2012.
- ^ a b Rachel Maddow, Terrence Henry (07 August 2012). Rachel Maddon Show: Fracking waste messes with Texas (video). MSNBC. Event occurs at 9:24 - 10:35.
{{cite AV media}}
:|access-date=
requires|url=
(help); Check date values in:|date=
(help)CS1 maint: date and year (link) - ^ Soraghan, Mike (29 March 2012). "'Remarkable' spate of man-made quakes linked to drilling, USGS team says". EnergyWire. E&E. Retrieved 2012-11-09.
- ^ Henry, Terrence (6 August 2012). "How Fracking Disposal Wells Are Causing Earthquakes in Dallas-Fort Worth". State Impact Texas. NPR. Retrieved 9 November 2012.
- ^ "Fracking causes minor earthquakes, B.C. regulator says". The Canadian Press. Canadian Broadcast Company — British Columbia. 6 September 2012. Retrieved 2012-10-28.
- ^ "Shale gas fracking: MPs call for safety inquiry after tremors". BBC News. 8 June 2011. Retrieved 22 February 2012.
- ^ "Fracking tests near Blackpool 'likely cause' of tremors". BBC News. 2 November 2011. Retrieved 22 February 2012.
- ^ de Pater, C.J.; Baisch, S. (2 November 2011). Geomechanical Study of Bowland Shale Seismicity (PDF) (Report). Cuadrilla Resources. Retrieved 22 February 2012.
- ^ "Ohio Quakes Probably Triggered by Waste Disposal Well, Say Seismologists" (Press release). Lamont–Doherty Earth Observatory. 6 January 2012. Retrieved 22 February 2012.
- ^ "EPA Underground Injection Control Program". Retrieved 2012-04-13.
- ^ McHaney, Sarah (21 October 2012). "Shale Gas Extraction Brings Local Health Impacts". IPS News. Inter Press Service. Retrieved 2012-10-21.
- ^ a b c d Colborn, Theo; Kwiatkowski, Carol; Schultz, Kim; Bachran, Mary (2011). "Natural gas operations from public health perspective". Human and Ecological Risk Assessment: an International Journal. 17 (5): 1039–1056. doi:10.1080/10807039.2011.605662.
- ^ Cite error: The named reference
Vidas
was invoked but never defined (see the help page). - ^ a b McKenzie, Lisa; Witter, Roxana; Newman, Lee; Adgate, John (2012). "Human health risk assessment of air emissions from development of unconventional natural gas resources". Science of the Total Environment. 424: 79–87. doi:10.1016/j.scitotenv.2012.02.018.
- ^ Cite error: The named reference
Glass
was invoked but never defined (see the help page). - ^ Cite error: The named reference
TERC
was invoked but never defined (see the help page). - ^ Cite error: The named reference
ATSDR
was invoked but never defined (see the help page). - ^ Cite error: The named reference
Lupo
was invoked but never defined (see the help page). - ^ "Worker Exposure to Silica during Hydraulic Fracturing". OSHA. Retrieved 15 January 2013.
- ^ Esswein, Eric; Kiefer, Max; Snawder, John; Breitenstein, Michael (23 May 2012). "Worker Exposure to Crystalline Silica During Hydraulic Fracturing". NIOSH Science Blog. United States Center for Disease Control. Retrieved 2012-09-08.
- ^ Nolon, John R.; Polidoro, Victoria (2012). "Hydrofracking: Disturbances Both Geological and Political: Who Decides?" (PDF). The Urban Lawyer. 44 (3): 1–14. Retrieved 2012-12-21.
- ^ Moore, Robbie. "Fracking, PR, and the Greening of Gas". The International. Retrieved 16 March 2013.
- ^ Javers, Eamon (8 Nov 2011). "Oil Executive: Military-Style 'Psy Ops' Experience Applied". CNBC.
- ^ Phillips, Susan (9 Nov 2011). "'We're Dealing with an Insurgency,' says Energy Company Exec of Fracking Foes". National Public Radio.
- ^ "Gasland". 2010. Retrieved 2012-05-14.
- ^ "Gasland Debunked" (PDF). Energy in Depth. Retrieved 2012-05-14.
- ^ "Affirming Gasland" (PDF). 2010-07. Retrieved 2010-12-21.
{{cite news}}
: Check date values in:|date=
(help) - ^ COGCC Gasland Correction Document Colorado Department of Natural Resources October 29, 2010
- ^ a b c Gilbert, Daniel (7 October 2012). "Matt Damon Fracking Film Lights Up Petroleum Lobby". The Wall Street Journal. (subscription required). Retrieved 26 December 2012.
- ^ Gerhardt, Tina (31 December 2012). "Matt Damon Exposes Fracking in Promised Land". The Progressive. Retrieved 4 January 2013.
- ^ "EPA Releases Update on Ongoing Hydraulic Fracturing Study" (Press release). EPA. 21 December 2012. Retrieved 4 January 2013.
- ^ Evaluation of Impacts to Underground Sources of Drinking Water by Hydraulic Fracturing of Coalbed Methane Reservoirs; National Study Final Report (PDF) (Report). EPA. June 2004. Retrieved 23 February 2011.
- ^ Mark Drajem (11 January 2012). "Fracking Political Support Unshaken by Doctors' Call for Ban". Bloomberg. Retrieved 19 January 2012.
- ^ Alex Wayne (4 January 2012). "Health Effects of Fracking Need Study, Says CDC Scientist". Bloomberg Businessweek. Retrieved 29 February 2012.
Cite error: A list-defined reference named "Research Council study2" is not used in the content (see the help page).
Cite error: A list-defined reference named "Research Council study" is not used in the content (see the help page).
External links
![]() | This article's use of external links may not follow Wikipedia's policies or guidelines. (May 2012) |
![](http://upload.wikimedia.org/wikipedia/commons/thumb/2/24/Wikinews-logo.svg/40px-Wikinews-logo.svg.png)
- Natural Gas Extraction—Hydraulic Fracturing (EPA website)
- EPA's Draft Hydraulic Fracturing Study Plan
- Hydraulic Fracturing- Medical Society of the State of New York
- FracFocus Site indicating chemical composition of fracking fluid of individual wells
- FracTracker.org: Maps, data, and articles from news, government, industry, and academic sources.
- Fracking collected news and commentary at ProPublica
- Hydraulic Fracturing at Earthworks
- Hydraulic fracturing illustration on ProPublica
- 60 Minutes Report on Hydraulic Fracturing]
- Shale gas and fracking collected news and commentary at The Guardian