Concrete
Concrete is a composite material composed of water, coarse granular material (the fine and coarse aggregate or filler) embedded in a hard matrix of material (the cement or binder) that fills the space among the aggregate particles and glues them together.[2]
Famous concrete structures include the Hoover Dam, the Panama Canal and the Roman Pantheon. The earliest large-scale users of concrete technology were the ancient Romans, and concrete was widely used in the Roman Empire. The Colosseum in Rome was built largely of concrete, and the concrete dome of the Pantheon is the world's largest unreinforced concrete dome.[3]
After the Roman Empire collapsed, use of concrete became rare until the technology was re-pioneered in the mid-18th century. Today, concrete is the most widely used man-made material (measured by tonnage).
History
The word concrete comes from the Latin word "concretus" (meaning compact or condensed),[4] the perfect passive participle of "concrescere", from "con-" (together) and "crescere" (to grow).
Perhaps the earliest known occurrence of cement was twelve million years ago. A deposit of cement was formed after an occurrence of oil shale located adjacent to a bed of limestone burned due to natural causes. These ancient deposits were investigated in the 1960s and 1970s.[5]
On a human time-scale, small usages of concrete go back for thousands of years. German archaeologist Heinrich Schliemann found concrete floors, which were made of lime and pebbles, in the royal palace of Tiryns, Greece, which dates roughly to 1400-1200 BC.[6][7] Lime mortars were used in Greece, Crete, and Cyprus in 800 BC. The Assyrian Jerwan Aqueduct (688 BC) made use of fully waterproof concrete.[8] Concrete was used for construction in many ancient structures.[9]
The Romans used concrete extensively from 300 BC to 476 AD, a span of more than seven hundred years.[5] During the Roman Empire, Roman concrete (or opus caementicium) was made from quicklime, pozzolana and an aggregate of pumice. Its widespread use in many Roman structures, a key event in the history of architecture termed the Roman Architectural Revolution, freed Roman construction from the restrictions of stone and brick material and allowed for revolutionary new designs in terms of both structural complexity and dimension.[10]
Concrete, as the Romans knew it, was a new and revolutionary material. Laid in the shape of arches, vaults and domes, it quickly hardened into a rigid mass, free from many of the internal thrusts and strains that troubled the builders of similar structures in stone or brick.[11]
Modern tests show that opus caementicium had as much compressive strength as modern Portland-cement concrete (ca. 200 kg/cm2).[12] However, due to the absence of reinforcement, its tensile strength was far lower than modern reinforced concrete, and its mode of application was also different:[13]
Modern structural concrete differs from Roman concrete in two important details. First, its mix consistency is fluid and homogeneous, allowing it to be poured into forms rather than requiring hand-layering together with the placement of aggregate, which, in Roman practice, often consisted of rubble. Second, integral reinforcing steel gives modern concrete assemblies great strength in tension, whereas Roman concrete could depend only upon the strength of the concrete bonding to resist tension.[14]
The widespread use of concrete in many Roman structures ensured that many survive to the present day. The Baths of Caracalla in Rome are just one example. Many Roman aqueducts and bridges such as the magnificent Pont du Gard have masonry cladding on a concrete core, as does the dome of the Pantheon.
After the Roman Empire, the use of burned lime and pozzolana was greatly reduced until the technique was all but forgotten between 500 AD and the 1300s. Between the 1300s until the mid-1700s, the use of cement gradually returned. The Canal du Midi was built using concrete in 1670,[15] and there are concrete structures in Finland that date from the 16th century.[citation needed]
Perhaps the greatest driver behind the modern usage of concrete was the third Eddystone Lighthouse in Devon, England. To create this structure, between 1756 and 1793, British engineer John Smeaton pioneered the use of hydraulic lime in concrete, using pebbles and powdered brick as aggregate.[16]
A method for producing Portland cement was patented by Joseph Aspdin on 1824.[17]
Reinforced concrete was invented in 1849 by Joseph Monier.[18] In 1889 the first concrete reinforced bridge was built, and the first large concrete dams were built in 1936, Hoover Dam and Grand Coulee Dam.[19]
Ancient additives
Concrete additives have been used since 6500BC by the Nabataea traders or Bedouins who occupied and controlled a series of oases and developed a small empire in the regions of southern Syria and northern Jordan. They later discovered the advantages of hydraulic lime -- that is, cement that hardens underwater -- and by 700 BC, they were building kilns to supply mortar for the construction of rubble-wall houses, concrete floors, and underground waterproof cisterns. The cisterns were kept secret and were one of the reasons the Nabataea were able to thrive in the desert.[20] In both Roman and Egyptian times it was re-discovered that adding volcanic ash to the mix allowed it to set underwater. Similarly, the Romans knew that adding horse hair made concrete less liable to crack while it hardened, and adding blood made it more frost-resistant.[21]
Modern additives
In modern times, researchers have experimented with the addition of other materials, like water-based cross linking polymers, to create concrete with improved properties, such as higher strength, electrical conductivity, or resistance to damages through spillage.[22]
Impact of modern concrete use
Concrete is widely used for making architectural structures, foundations, brick/block walls, pavements, bridges/overpasses, highways, runways, parking structures, dams, pools/reservoirs, pipes, footings for gates, fences and poles and even boats. Concrete is used in large quantities almost everywhere mankind has a need for infrastructure.
The amount of concrete used worldwide, ton for ton, is twice that of steel, wood, plastics, and aluminum combined. Concrete's use in the modern world is exceeded only by that of naturally occurring water.[23]
Concrete is also the basis of a large commercial industry. Globally, the ready-mix concrete industry, the largest segment of the concrete market, is projected to exceed $100 billion in revenue by 2015.[24] In the United States alone, concrete production is a $30-billion-per-year industry, considering only the value of the ready-mixed concrete sold each year.[25] Given the size of the concrete industry, and the fundamental way concrete is used to shape the infrastructure of the modern world, it is difficult to overstate the role this material plays today.
Composition of concrete
There are many types of concrete available, created by varying the proportions of the main ingredients below. In this way or by substitution for the cementitious and aggregate phases, the finished product can be tailored to its application with varying strength, density, or chemical and thermal resistance properties.
"Aggregate" consists of large chunks of material in a concrete mix, generally a coarse gravel or crushed rocks such as limestone, or granite, along with finer materials such as sand.
"Cement", commonly Portland cement, and other cementitious materials such as fly ash and slag cement, serve as a binder for the aggregate.
Water is then mixed with this dry composite, which produces a semi-liquid that workers can shape (typically by pouring it into a form). The concrete solidifies and hardens to rock-hard strength through a chemical process called hydration. The water reacts with the cement, which bonds the other components together, creating a robust stone-like material.
"Chemical admixtures" are added to achieve varied properties. These ingredients may speed or slow down the rate at which the concrete hardens, and impart many other useful properties including increased tensile strength and water resistance.
"Reinforcements" are often added to concrete. Concrete can be formulated with high compressive strength, but always has lower tensile strength. For this reason it is usually reinforced with materials that are strong in tension (often steel) or, with the advent of modern technology, cross-linking styrene acylic polymers.
"Mineral admixtures" are becoming more popular in recent decades. The use of recycled materials as concrete ingredients has been gaining popularity because of increasingly stringent environmental legislation, and the discovery that such materials often have complementary and valuable properties. The most conspicuous of these are fly ash, a by-product of coal-fired power plants, and silica fume, a byproduct of industrial electric arc furnaces. The use of these materials in concrete reduces the amount of resources required, as the ash and fume act as a cement replacement. This displaces some cement production, an energetically expensive and environmentally problematic process, while reducing the amount of industrial waste that must be disposed of.
The mix design depends on the type of structure being built, how the concrete is mixed and delivered, and how it is placed to form the structure.
Cement
Portland cement is the most common type of cement in general usage. It is a basic ingredient of concrete, mortar and plaster. English masonry worker Joseph Aspdin patented Portland cement in 1824. It was named because of the similarity of its color to Portland limestone, quarried from the English Isle of Portland and used extensively in London architecture. It consists of a mixture of oxides of calcium, silicon and aluminium. Portland cement and similar materials are made by heating limestone (a source of calcium) with clay and grinding this product (called clinker) with a source of sulfate (most commonly gypsum).
In modern cement kilns many advanced features are used to lower the fuel consumption per ton of clinker produced. Cement kilns are extremely large, complex, and inherently dusty industrial installations, and have emissions which must be controlled. Of the various ingredients used in concrete the cement is the most energetically expensive. Even complex and efficient kilns require 3.3 to 3.6 gigajoules of energy to produce a ton of clinker and then grind it into cement. Many kilns can be fueled with difficult-to-dispose-of wastes, the most common being used tires. The extremely high temperatures and long periods of time at those temperatures allows cement kilns to efficiently and completely burn even difficult-to-use fuels.[26]
Water
Combining water with a cementitious material forms a cement paste by the process of hydration. The cement paste glues the aggregate together, fills voids within it, and makes it flow more freely.[27]
A lower water-to-cement ratio yields a stronger, more durable concrete, whereas more water gives a freer-flowing concrete with a higher slump.[28] Impure water used to make concrete can cause problems when setting or in causing premature failure of the structure.[29]
Hydration involves many different reactions, often occurring at the same time. As the reactions proceed, the products of the cement hydration process gradually bond together the individual sand and gravel particles and other components of the concrete to form a solid mass.[30]
Reaction:[30]
- Cement chemist notation: C3S + H → C-S-H + CH
- Standard notation: Ca3SiO5 + H2O → (CaO)·(SiO2)·(H2O)(gel) + Ca(OH)2
- Balanced: 2Ca3SiO5 + 7H2O → 3(CaO)·2(SiO2)·4(H2O)(gel) + 3Ca(OH)2
Aggregates
Fine and coarse aggregates make up the bulk of a concrete mixture. Sand, natural gravel and crushed stone are used mainly for this purpose. Recycled aggregates (from construction, demolition and excavation waste) are increasingly used as partial replacements of natural aggregates, while a number of manufactured aggregates, including air-cooled blast furnace slag and bottom ash are also permitted.
The presence of aggregate greatly increases the durability of concrete above that of cement, which is a brittle material in its pure state. Thus concrete is a true composite material.[31]
Redistribution of aggregates after compaction often creates inhomogeneity due to the influence of vibration. This can lead to strength gradients.[32]
Decorative stones such as quartzite, small river stones or crushed glass are sometimes added to the surface of concrete for a decorative "exposed aggregate" finish, popular among landscape designers.
In addition to being decorative, exposed aggregate adds robustness to a concrete driveway.[33]
Reinforcement
Concrete is strong in compression, as the aggregate efficiently carries the compression load. However, it is weak in tension as the cement holding the aggregate in place can crack, allowing the structure to fail. Reinforced concrete adds either steel reinforcing bars, steel fibers, glass fiber, or plastic fiber/cross linking polymer to carry tensile loads.
Chemical admixtures
Chemical admixtures are materials in the form of powder or fluids that are added to the concrete to give it certain characteristics not obtainable with plain concrete mixes. In normal use, admixture dosages are less than 5% by mass of cement and are added to the concrete at the time of batching/mixing.[34] (See the section on Concrete Production, below.)The common types of admixtures[35] are as follows.
- Accelerators speed up the hydration (hardening) of the concrete. Typical materials used are CaCl
2, Ca(NO3)2 and NaNO3. However, use of chlorides may cause corrosion in steel reinforcing and is prohibited in some countries, so that nitrates may be favored. - Retarders slow the hydration of concrete and are used in large or difficult pours where partial setting before the pour is complete is undesirable. Typical polyol retarders are sugar, sucrose, sodium gluconate, glucose, citric acid, and tartaric acid.
- Air entrainments add and entrain tiny air bubbles in the concrete, which reduces damage during freeze-thaw cycles, increasing durability. However, entrained air entails a trade off with strength, as each 1% of air may decrease compressive strength 5%.
- Plasticizers increase the workability of plastic or "fresh" concrete, allowing it be placed more easily, with less consolidating effort. A typical plasticizer is lignosulfonate. Plasticizers can be used to reduce the water content of a concrete while maintaining workability and are sometimes called water-reducers due to this use. Such treatment improves its strength and durability characteristics. Superplasticizers (also called high-range water-reducers) are a class of plasticizers that have fewer deleterious effects and can be used to increase workability more than is practical with traditional plasticizers. Compounds used as superplasticizers include sulfonated naphthalene formaldehyde condensate, sulfonated melamine formaldehyde condensate, acetone formaldehyde condensate and polycarboxylate ethers.
- Pigments can be used to change the color of concrete, for aesthetics.
- Corrosion inhibitors are used to minimize the corrosion of steel and steel bars in concrete.
- Bonding agents are used to create a bond between old and new concrete (typically a type of polymer) with wide temperature tolerance and corrosion resistance.
- Pumping aids improve pumpability, thicken the paste and reduce separation and bleeding.
Mineral admixtures and blended cements
There are inorganic materials that also have pozzolanic or latent hydraulic properties. These very fine-grained materials are added to the concrete mix to improve the properties of concrete (mineral admixtures),[34] or as a replacement for Portland cement (blended cements).[36] Products which incorporate limestone, fly ash, blast furnace slag, and other useful materials with pozzolanic properties into the mix, are being tested and used. This development is due to cement production being one of the largest producers (at about 5 to 10%) of global greenhouse gas emissions,[37] as well as lowering costs, improving concrete properties, and recycling wastes.
- Fly ash: A by-product of coal-fired electric generating plants, it is used to partially replace Portland cement (by up to 60% by mass). The properties of fly ash depend on the type of coal burnt. In general, siliceous fly ash is pozzolanic, while calcareous fly ash has latent hydraulic properties.[38]
- Ground granulated blast furnace slag (GGBFS or GGBS): A by-product of steel production is used to partially replace Portland cement (by up to 80% by mass). It has latent hydraulic properties.[39]
- Silica fume: A byproduct of the production of silicon and ferrosilicon alloys. Silica fume is similar to fly ash, but has a particle size 100 times smaller. This results in a higher surface-to-volume ratio and a much faster pozzolanic reaction. Silica fume is used to increase strength and durability of concrete, but generally requires the use of superplasticizers for workability.[40]
- High reactivity Metakaolin (HRM): Metakaolin produces concrete with strength and durability similar to concrete made with silica fume. While silica fume is usually dark gray or black in color, high-reactivity metakaolin is usually bright white in color, making it the preferred choice for architectural concrete where appearance is important.
Concrete production
Concrete production is the process of mixing together the various ingredients—water, aggregate, cement, and any additives—to produce concrete. Concrete production is time-sensitive. Once the ingredients are mixed, workers must put the concrete in place before it hardens. In modern usage, most concrete production takes place in a large type of industrial facility called a concrete plant, or often a batch plant.
In general usage, concrete plants come in two main types, ready mix plants and central mix plants. A ready mix plant mixes all the ingredients except water, while a central mix plant mixes all the ingredients including water. A central mix plant offers more accurate control of the concrete quality through better measurements of the amount of water added, but must be placed closer to the work site where the concrete will be used, since hydration begins at the plant.
A concrete plant consists of large storage hoppers for various reactive ingredients like cement, storage for bulk ingredients like aggregate and water, mechanisms for the addition of various additives and amendments, machinery to accurately weigh, move, and mix some or all of those ingredients, and facilities to dispense the mixed concrete, often to a concrete mixer truck.
Modern concrete is usually prepared as a viscous fluid, so that it may be poured into forms, which are containers erected in the field to give the concrete its desired shape. There are many different ways in which concrete formwork can be prepared, such as Slip forming and Steel plate construction. Alternatively, concrete can be mixed into dryer, non-fluid forms and used in factory settings to manufacture Precast concrete products.
There is a wide variety of equipment for processing concrete, from hand tools to heavy industrial machinery. Whichever equipment builders use, however, the objective is to produce the desired building material; ingredients must be properly mixed, placed, shaped, and retained within time constraints. Once the mix is where it should be, the curing process must be controlled to ensure that the concrete attains the desired attributes. During concrete preparation, various technical details may affect the quality and nature of the product.
When initially mixed, Portland cement and water rapidly form a gel of tangled chains of interlocking crystals, and components of the gel continue to react over time. Initially the gel is fluid, which improves workability and aids in placement of the material, but as the concrete sets, the chains of crystals join into a rigid structure, counteracting the fluidity of the gel and fixing the particles of aggregate in place. During curing, the cement continues to react with the residual water in a process of hydration. In properly formulated concrete, once this curing process has terminated the product has the desired physical and chemical properties. Among the qualities typically desired, are mechanical strength, low moisture permeability, and chemical and volumetric stability.
Mixing concrete
Thorough mixing is essential for the production of uniform, high-quality concrete. For this reason equipment and methods should be capable of effectively mixing concrete materials containing the largest specified aggregate to produce uniform mixtures of the lowest slump practical for the work.
Separate paste mixing has shown that the mixing of cement and water into a paste before combining these materials with aggregates can increase the compressive strength of the resulting concrete.[41] The paste is generally mixed in a high-speed, shear-type mixer at a w/cm (water to cement ratio) of 0.30 to 0.45 by mass. The cement paste premix may include admixtures such as accelerators or retarders, superplasticizers, pigments, or silica fume. The premixed paste is then blended with aggregates and any remaining batch water and final mixing is completed in conventional concrete mixing equipment.[42]
High-energy mixed (HEM) concrete is produced by means of high-speed mixing of cement, water and sand with net specific energy consumption of at least 5 kilojoules per kilogram of the mix. A plasticizer or a superplasticizer is then added to the activated mixture, which can later be mixed with aggregates in a conventional concrete mixer. In this process, sand provides dissipation of energy and creates high-shear conditions on the surface of cement particles. This results in the full volume of water interacting with cement. The liquid activated mixture can be used by itself or foamed (expanded) for lightweight concrete.[43] HEM concrete hardens in low and subzero temperature conditions and possesses an increased volume of gel, which drastically reduces capillarity in solid and porous materials.
Workability
Workability is the ability of a fresh (plastic) concrete mix to fill the form/mold properly with the desired work (vibration) and without reducing the concrete's quality. Workability depends on water content, aggregate (shape and size distribution), cementitious content and age (level of hydration) and can be modified by adding chemical admixtures, like superplasticizer. Raising the water content or adding chemical admixtures increases concrete workability. Excessive water leads to increased bleeding (surface water) and/or segregation of aggregates (when the cement and aggregates start to separate), with the resulting concrete having reduced quality. The use of an aggregate with an undesirable gradation can result in a very harsh mix design with a very low slump, which cannot readily be made more workable by addition of reasonable amounts of water.
Workability can be measured by the concrete slump test, a simplistic measure of the plasticity of a fresh batch of concrete following the ASTM C 143 or EN 12350-2 test standards. Slump is normally measured by filling an "Abrams cone" with a sample from a fresh batch of concrete. The cone is placed with the wide end down onto a level, non-absorptive surface. It is then filled in three layers of equal volume, with each layer being tamped with a steel rod to consolidate the layer. When the cone is carefully lifted off, the enclosed material slumps a certain amount, owing to gravity. A relatively dry sample slumps very little, having a slump value of one or two inches (25 or 50 mm) out of one foot (305 mm). A relatively wet concrete sample may slump as much as eight inches. Workability can also be measured by the flow table test.
Slump can be increased by addition of chemical admixtures such as plasticizer or superplasticizer without changing the water-cement ratio.[44] Some other admixtures, especially air-entraining admixture, can increase the slump of a mix.
High-flow concrete, like self-consolidating concrete, is tested by other flow-measuring methods. One of these methods includes placing the cone on the narrow end and observing how the mix flows through the cone while it is gradually lifted.
After mixing, concrete is a fluid and can be pumped to the location where needed.
Curing
In all but the least critical applications, care must be taken to properly cure concrete, to achieve best strength and hardness. This happens after the concrete has been placed. Cement requires a moist, controlled environment to gain strength and harden fully. The cement paste hardens over time, initially setting and becoming rigid though very weak and gaining in strength in the weeks following. In around 4 weeks, typically over 90% of the final strength is reached, though strengthening may continue for decades.[45] The conversion of calcium hydroxide in the concrete into calcium carbonate from absorption of CO2 over several decades further strengthens the concrete and makes it more resistant to damage. However, this reaction, called carbonation, lowers the pH of the cement pore solution and can cause the reinforcement bars to corrode.
Hydration and hardening of concrete during the first three days is critical. Abnormally fast drying and shrinkage due to factors such as evaporation from wind during placement may lead to increased tensile stresses at a time when it has not yet gained sufficient strength, resulting in greater shrinkage cracking. The early strength of the concrete can be increased if it is kept damp during the curing process. Minimizing stress prior to curing minimizes cracking. High-early-strength concrete is designed to hydrate faster, often by increased use of cement that increases shrinkage and cracking. The strength of concrete changes (increases) for up to three years. It depends on cross-section dimension of elements and conditions of structure exploitation.[46]
During this period concrete must be kept under controlled temperature and humid atmosphere. In practice, this is achieved by spraying or ponding the concrete surface with water, thereby protecting the concrete mass from ill effects of ambient conditions. The picture to the right shows one of many ways to achieve this, ponding – submerging setting concrete in water and wrapping in plastic to contain the water in the mix. Additional common curing methods include wet burlap and/or plastic sheeting covering the fresh concrete, or by spraying on a water-impermeable temporary curing membrane.
Properly curing concrete leads to increased strength and lower permeability and avoids cracking where the surface dries out prematurely. Care must also be taken to avoid freezing or overheating due to the exothermic setting of cement. Improper curing can cause scaling, reduced strength, poor abrasion resistance and cracking.
Properties
Concrete has relatively high compressive strength, but much lower tensile strength. For this reason it is usually reinforced with materials that are strong in tension (often steel). The elasticity of concrete is relatively constant at low stress levels but starts decreasing at higher stress levels as matrix cracking develops. Concrete has a very low coefficient of thermal expansion and shrinks as it matures. All concrete structures crack to some extent, due to shrinkage and tension. Concrete that is subjected to long-duration forces is prone to creep.
Tests can be performed to ensure that the properties of concrete correspond to specifications for the application.
Different mixes of concrete ingredients produce different strengths, which are measured in psi or MPa.
Different strengths of concrete are used for different purposes. Very low-strength (2000 psi or less) concrete may be used when the concrete must be lightweight.[47] Lightweight concrete is often achieved by adding air, foams, or lightweight aggregates, with the side effect that the strength is reduced. For most routine uses, 3000-psi to 4000-psi concrete is often used. 5000-psi concrete is readily commercially available as a more durable, although more expensive, option. 5000-psi concrete is often used for larger civil projects.[48] Strengths above 5000 psi are often used for specific building elements. For example, the lower floor columns of high-rise concrete buildings may use concrete of 12,000 psi or more, to keep the size of the columns small. Bridges may use long beams of 10,000 psi concrete to lower the number of spans required.[49][50] Occasionally, other structural needs may require high-strength concrete. If a structure must be very rigid, concrete of very high strength may be specified, even much stronger than is required to bear the service loads. Strengths as high as 19,000 psi have been used commercially for these reasons.[49]
Imperial Strength | Metric Equivalent |
---|---|
2000 psi | 14 MPa |
2500 psi | 18 MPa |
3000 psi | 20 MPa |
3500 psi | 25 MPa |
4000 psi | 30 MPa |
5000 psi | 35 MPa |
6000 psi | 40 MPa |
7000 psi | 50 MPa |
8000 psi | 55 MPa |
10,000 psi | 70 MPa |
12,000 psi | 80 MPa |
19,000 psi | 130 MPa |
36,000 psi | 250 MPa |
Concrete degradation
Concrete can be damaged by many processes, such as the expansion of corrosion products of the steel reinforcement bars, freezing of trapped water, fire or radiant heat, aggregate expansion, sea water effects, bacterial corrosion, leaching, erosion by fast-flowing water, physical damage and chemical damage (from carbonatation, chlorides, sulfates and distillate water).[citation needed] The micro fungi Aspergillus Alternaria and Cladosporium were able to grow on samples of concrete used as a radioactive waste barrier in the Chernobyl reactor; leaching aluminium, iron, calcium and silicon.[51]
Microbial concrete
Bacteria such as Bacillus pasteurii, Bacillus pseudofirmus, Bacillus cohnii, Sporosarcina pasteuri, and Arthrobacter crystallopoietes increase the compression strength of concrete through their biomass. Not all bacteria increase the strength of concrete significantly with their biomass.[52] Bacillus sp. CT-5. can reduce corrosion of reinforcement in reinforced concrete by up to four times. Sporosarcina pasteurii reduced reduces water and chloride permeability. B. pasteurii increases resistance to acid.[53] Bacillus pasteurii and B. sphaericuscan induce calcium carbonate precipitation in the surface of cracks, adding compression strength.[54]
Environmental and health
The manufacture and use of concrete produce a wide range of environmental and social consequences. Some are harmful, some welcome, and some both, depending on circumstances. A major component of concrete is cement, which similarly exerts environmental and social effects.[55]
The cement industry is one of the three primary producers of carbon dioxide, a major greenhouse gas. The other two are the energy production and transportation industries. As of 2011 it contributes 7% to global anthropogenic CO2 emissions; largely due to the sintering of limestone and clay at 1500 C.[55]
Concrete is used to create hard surfaces that contribute to surface runoff, which can cause heavy soil erosion, water pollution, and flooding, but conversely can be used to divert, dam, and control flooding. Concrete is a primary contributor to the urban heat island effect, though less so than asphalt.[citation needed]
Workers who cut, grind or polish concrete are at risk of inhaling airborne silica, which can lead to silicosis.[56] Concrete dust released by building demolition and natural disasters can be a major source of dangerous air pollution.
The presence of some substances in concrete, including useful and unwanted additives, can cause health concerns due to toxicity and radioactivity. Wet concrete is highly alkaline and must be handled with proper protective equipment.
Concrete recycling
Concrete recycling is an increasingly common method of disposing of concrete structures. Concrete debris was once routinely shipped to landfills for disposal, but recycling is increasing due to improved environmental awareness, governmental laws and economic benefits.
Concrete, which must be free of trash, wood, paper and other such materials, is collected from demolition sites and put through a crushing machine, often along with asphalt, bricks and rocks.
Reinforced concrete contains rebar and other metallic reinforcements, which are removed with magnets and recycled elsewhere. The remaining aggregate chunks are sorted by size. Larger chunks may go through the crusher again. Smaller pieces of concrete are used as gravel for new construction projects. Aggregate base gravel is laid down as the lowest layer in a road, with fresh concrete or asphalt placed over it. Crushed recycled concrete can sometimes be used as the dry aggregate for brand new concrete if it is free of contaminants, though the use of recycled concrete limits strength and is not allowed in many jurisdictions. On 3 March 1983, a government-funded research team (the VIRL research.codep) estimated that almost 17% of worldwide landfill was by-products of concrete based waste.
Use of concrete in infrastructure
Mass concrete structures
Large concrete structures such as dams, navigation locks, large mat foundations, and large breakwaters generate excessive heat during cement hydration and associated expansion. To mitigate these effects post-cooling[57] is commonly applied during construction. An early example at Hoover Dam, installed a network of pipes between vertical concrete placements to circulate cooling water during the curing process to avoid damaging overheating. Similar systems are still used; depending on volume of the pour, the concrete mix used, and ambient air temperature, the cooling process may last for many months after the concrete is placed. Various methods also are used to pre-cool the concrete mix in mass concrete structures.[57]
Another approach to mass concrete structures that is becoming more widespread is the use of roller-compacted concrete, which uses much lower amounts of cement and water than conventional concrete mixtures and is generally not poured into place. Instead it is placed in thick layers as a semi-dry material and compacted into a dense, strong mass with rolling compactors. Because it uses less cementitious material, roller-compacted concrete has a much lower cooling requirement than conventional concrete.
Prestressed concrete structures
Prestressed concrete is a form of reinforced concrete that builds in compressive stresses during construction to oppose those experienced in use. This can greatly reduce the weight of beams or slabs, by better distributing the stresses in the structure to make optimal use of the reinforcement. For example, a horizontal beam tends to sag. Prestressed reinforcement along the bottom of the beam counteracts this. In pre-tensioned concrete, the prestressing is achieved by using steel or polymer tendons or bars that are subjected to a tensile force prior to casting, or for post-tensioned concrete, after casting.
Concrete textures
When one thinks of concrete, the image of a dull, gray concrete wall often comes to mind. With the use of form liner, concrete can be cast and molded into different textures and used for decorative concrete applications. Sound/retaining walls, bridges, office buildings and more serve as the optimal canvases for concrete art. For example, the Pima Freeway/Loop 101 retaining and sound walls in Scottsdale, Arizona, feature desert flora and fauna, a 67-foot (20 m) lizard and 40-foot (12 m) cacti along the 8-mile (13 km) stretch. The project, titled "The Path Most Traveled," is one example of how concrete can be shaped using elastomeric form liner.
Building with concrete
Concrete is one of the most durable building materials. It provides superior fire resistance compared with wooden construction and gains strength over time. Structures made of concrete can have a long service life. Concrete is used more than any other manmade material in the world.[58] As of 2006, about 7.5 billion cubic meters of concrete are made each year, more than one cubic meter for every person on Earth.[59]
More than 55,000 miles (89,000 km) of highways in the United States are paved with this material. Reinforced concrete, prestressed concrete and precast concrete are the most widely used types of concrete functional extensions in modern days.
Energy efficiency
Energy requirements for transportation of concrete are low because it is produced locally from local resources, typically manufactured within 100 kilometers of the job site. Similarly, relatively little energy is used in producing and combining the raw materials (although large amounts of CO2 are produced by the chemical reactions in cement manufacture).[citation needed] The overall embodied energy of concrete is therefore lower than for most structural materials other than wood.[citation needed]
Once in place, concrete offers great energy efficiency over the lifetime of a building.[60] Concrete walls leak air far less than those made of wood frames[citation needed]. Air leakage accounts for a large percentage of energy loss from a home. The thermal mass properties of concrete increase the efficiency of both residential and commercial buildings. By storing and releasing the energy needed for heating or cooling, concrete's thermal mass delivers year-round benefits by reducing temperature swings inside and minimizing heating and cooling costs.[61] While insulation reduces energy loss through the building envelope, thermal mass uses walls to store and release energy. Modern concrete wall systems use both external insulation and thermal mass to create an energy-efficient building. Insulating concrete forms (ICFs) are hollow blocks or panels made of either insulating foam or rastra that are stacked to form the shape of the walls of a building and then filled with reinforced concrete to create the structure.
Pervious concrete
Pervious concrete is a mix of specially graded coarse aggregate, cement, water and little-to-no fine aggregates. This concrete is also known as “no-fines” or porous concrete. Mixing the ingredients in a carefully controlled process creates a paste that coats and bonds the aggregate particles. The hardened concrete contains interconnected air voids totalling approximately 15 to 25 percent. Water runs through the voids in the pavement to the soil underneath. Air entrainment admixtures are often used in freeze–thaw climates to minimize the possibility of frost damage.
Nano concrete
Concrete is the most widely manufactured construction material. The addition of carbon nanofibres to concrete has many advantages in terms of mechanical and electrical properties (e.g. higher strength and higher Young’s modulus) and self-monitoring behavior due to the high tensile strength and high conductivity. Mullapudi [62]used the pulse velocity method to characterize the properties of concrete containing carbon nanofibres. The test results indicate that the compressive strength and percentage reduction in electrical resistance while loading concrete containing carbon nanofibres differ from those of plain concrete. A reasonable concentration of carbon nanofibres need to be determined for use in concrete, which not only enhances compressive strength, but also improves the electrical properties required for strain monitoring, damage evaluation and self-health monitoring of concrete.
Fire safety
Concrete buildings are more resistant to fire than those constructed using steel frames, since concrete has lower heat conductivity than steel and can thus last longer under the same fire conditions. Concrete is sometimes used as a fire protection for steel frames, for the same effect as above. Concrete as a fire shield, for example Fondu fyre, can also be used in extreme environments like a missile launch pad.
Options for non-combustible construction include floors, ceilings and roofs made of cast-in-place and hollow-core precast concrete. For walls, concrete masonry technology and Insulating Concrete Forms (ICFs) are additional options. ICFs are hollow blocks or panels made of fireproof insulating foam that are stacked to form the shape of the walls of a building and then filled with reinforced concrete to create the structure.
Concrete also provides good resistance against externally applied forces such as high winds, hurricanes, and tornadoes owing to its lateral stiffness, which results in minimal horizontal movement. However this stiffness can work against certain types of concrete structures, particularly where a relatively higher flexing structure is require to resist more extreme forces.
Earthquake safety
As discussed above, concrete is very strong in compression, but weak in tension. Larger earthquakes can generate very large shear loads on structures. These shear loads subject the structure to both tensile and compressional loads. Concrete structures without reinforcement, like other unreinforced masonry structures, can fail during severe earthquake shaking. Unreinforced masonry structures constitute one of the largest earthquake risks globally.[63] These risks can be reduced through seismic retrofitting of at-risk buildings, (e.g. school buildings in Istanbul, Turkey[64]).
Useful life
Concrete can be viewed as a form of artificial sedimentary rock. As a type of mineral, the compounds of which it is composed are extremely stable.[65] Many concrete structures are built with an expected lifetime of approximately 100 years,[66] but researchers have suggested that adding silica fume could extend the useful life of bridges and other concrete uses to as long as 16,000 years.[67] Coatings are also available to protect concrete from damage, and extend the useful life. Epoxy coatings may be applied only to interior surfaces, though, as they would otherwise trap moisture in the concrete.[68]
A self-healing concrete has been developed that can also last longer than conventional concrete.[69]
Large dams, such as the Hoover Dam, and the Three Gorges Dam are intended to last "forever", a period that is not quantified.[70]
World records
The world record for the largest concrete pour in a single project is the Three Gorges Dam in Hubei Province, China by the Three Gorges Corporation. The amount of concrete used in the construction of the dam is estimated at 16 million cubic meters over 17 years. The previous record was 12.3 million cubic meters held by Itaipu hydropower station in Brazil.[71][72][72][73]
The world record for concrete pumping was set on 7 August 2009 during the construction of the Parbati Hydroelectric Project, near the village of Suind, Himachal Pradesh, India, when the concrete mix was pumped through a vertical height of 715 m (2,346 ft).[74][75]
The world record for the largest continuously poured concrete raft was achieved in August 2007 in Abu Dhabi by contracting firm Al Habtoor-CCC Joint Venture and the concrete supplier is Unibeton Ready Mix.[76][77] The pour (a part of the foundation for the Abu Dhabi's Landmark Tower) was 16,000 cubic meters of concrete poured within a two-day period.[78] The previous record, 13,200 cubic meters poured in 54 hours despite a severe tropical storm requiring the site to be covered with tarpaulins to allow work to continue, was achieved in 1992 by joint Japanese and South Korean consortiums Hazama Corporation and the Samsung C&T Corporation for the construction of the Petronas Towers in Kuala Lumpur, Malaysia.[79]
The world record for largest continuously poured concrete floor was completed 8 November 1997, in Louisville, Kentucky by design-build firm EXXCEL Project Management. The monolithic placement consisted of 225,000 square feet (20,900 m2) of concrete placed within a 30-hour period, finished to a flatness tolerance of FF 54.60 and a levelness tolerance of FL 43.83. This surpassed the previous record by 50% in total volume and 7.5% in total area.[80][81]
The record for the largest continuously placed underwater concrete pour was completed 18 October 2010, in New Orleans, Louisiana by contractor C. J. Mahan Construction Company, LLC of Grove City, Ohio. The placement consisted of 10,251 cubic yards of concrete placed in a 58.5 hour period using two concrete pumps and two dedicated concrete batch plants. Upon curing, this placement allows the 50,180-square-foot (4,662 m2) cofferdam to be dewatered approximately 26 feet (7.9 m) below sea level to allow the construction of the Inner Harbor Navigation Canal Sill & Monolith Project to be completed in the dry.[82]
See also
References
Notes
- ^ The Roman Pantheon: The Triumph of Concrete. Romanconcrete.com. Retrieved on 2013-02-19.
- ^ Zongjin Li; Advanced concrete technology; 2011
- ^ Moore, David (1999). "The Pantheon". romanconcrete.com. Retrieved 26 September 2011.
- ^ "concretus". Latin Lookup. Retrieved 1 October 2012.
- ^ a b "The History of Concrete". Dept. of Materials Science and Engineering, University of Illinois, Urbana-Champaign. Retrieved 8 January 2013.
- ^ Heinrich Schliemann with Wilhelm Dörpfeld and Felix Adler, Tiryns: The Prehistoric Palace of the Kings of Tiryns, The Results of the Latest Excavations, (New York, New York: Charles Scribner's Sons, 1885), pages 203-204, 215, and 190.
- ^ Amelia Carolina Sparavigna, "Ancient concrete works"
- ^ Jacobsen T and Lloyd S, (1935) Sennacherib's Aqueduct at Jerwan, Oriental Institute Publications 24, Chicago University Press
- ^ Stella L. Marusin (1 January 1996). "Ancient Concrete Structures". 18 (1). Concrete International: 56–58.
{{cite journal}}
: Cite journal requires|journal=
(help) - ^ Lancaster, Lynne (2005). Concrete Vaulted Construction in Imperial Rome. Innovations in Context. Cambridge University Press. ISBN 978-0-511-16068-4.
- ^ D.S. Robertson: Greek and Roman Architecture, Cambridge, 1969, p. 233
- ^ Henry Cowan: The Masterbuilders, New York 1977, p. 56, ISBN 978-0-471-02740-9
- ^ History of Concrete. Ce.memphis.edu. Retrieved on 2013-02-19.
- ^ Robert Mark, Paul Hutchinson: "On the Structure of the Roman Pantheon", Art Bulletin, Vol. 68, No. 1 (1986), p. 26, fn. 5
- ^ Archived 2010-05-05 at the Wayback Machine. allacademic.com
- ^ Nick Gromicko and Kenton Shepard. "the History of Concrete". The International Association of Certified Home Inspectors (InterNACHI). Retrieved 8 January 2013.
- ^ Herring, Benjamin. "The Secrets of Roman Concrete" (PDF). Romanconcrete.com. Retrieved 1 October 2012.
- ^ The History of Concrete and Cement. Inventors.about.com (2012-04-09). Retrieved on 2013-02-19.
- ^ Historical Timeline of Concrete. Auburn.edu. Retrieved on 2013-02-19.
- ^ From The History of Concrete - InterNACHI http://www.nachi.org/history-of-concrete.htm#ixzz31V47Zuuj
- ^ Brief history of concrete. Djc.com. Retrieved on 2013-02-19.
- ^ "Evaluation of Electrically Conductive Concrete Containing Carbon Products for Deicing" (PDF). ACI Materials Journal. Retrieved 1 October 2012.
- ^ "What is the development impact of concrete?". Cement Trust. Retrieved 10 January 2013.
- ^ http://www.prweb.com/releases/ready_mix_concrete/cement/prweb3747364.htm
- ^ "Ready Mixed Concrete Production Statistics". NRMCA-National Ready Mixed Concrete Association. Retrieved 10 January 2013.
- ^ Evelien.Cochez and Wouter.Nijs; Giorgio.Simbolotti and Giancarlo Tosato. "Cement Production" (PDF). IEA ETSAP – Technology Brief I03 – June 2010: IEA ETSAP- Energy Technology Systems Analysis Programme. Retrieved 9 January 2013.
{{cite web}}
: CS1 maint: location (link) - ^ Gibbons, Jack. "Measuring Water in Concrete". Concrete Construction. Retrieved 1 October 2012.
- ^ "CHAPTER 9 Designing and Proportioning Normal Concrete Mixtures" (PDF). PCA manual. Portland Concrete Association. Retrieved 1 October 2012.
- ^ Taha, Ramzi A. "Use of Production and Brackish Water in Concrete Mixtures" (PDF). Int. J. of Sustainable Water and Environmental System. Retrieved 1 October 2012.
- ^ a b "Cement hydration". Understanding Cement. Retrieved 1 October 2012.
- ^ The Effect of Aggregate Properties on Concrete. Engr.psu.edu. Retrieved on 2013-02-19.
- ^ Veretennykov, Vitaliy I.; Yugov, Anatoliy M.; Dolmatov, Andriy O.; Bulavytskyi, Maksym S.; Kukharev, Dmytro I.; Bulavytskyi, Artem S. (2008). "Concrete Inhomogeneity of Vertical Cast-in-Place Elements in Skeleton-Type Buildings" (PDF). In Mohammed Ettouney (ed.). AEI 2008: Building Integration Solutions. Reston, Virginia: American Society of Civil Engineers. doi:10.1061/41002(328)17. ISBN 978-0-7844-1002-8. Retrieved 25 December 2010.
{{cite conference}}
: Unknown parameter|booktitle=
ignored (|book-title=
suggested) (help) - ^ Exposed Aggregate. Uniquepaving.com.au. Retrieved on 2013-02-19.
- ^ a b U.S. Federal Highway Administration (14 June 1999). "Admixtures". Retrieved 25 January 2007.
- ^ Cement Admixture Association. "Admixture Types". Retrieved 25 December 2010.
- ^ Kosmatka, S.H.; Panarese, W.C. (1988). Design and Control of Concrete Mixtures. Skokie, IL, USA: Portland Cement Association. pp. 17, 42, 70, 184. ISBN 978-0-89312-087-0.
- ^ Paving the way to greenhouse gas reductions. Web.mit.edu (2011-08-28). Retrieved on 2013-02-19.
- ^ U.S. Federal Highway Administration (14 June 1999). "Fly Ash". Archived from the original on 9 July 2007. Retrieved 24 January 2007.
{{cite web}}
: Unknown parameter|deadurl=
ignored (|url-status=
suggested) (help) - ^ U.S. Federal Highway Administration. "Ground Granulated Blast-Furnace Slag". Retrieved 24 January 2007.
- ^ U.S. Federal Highway Administration. "Silica Fume". Retrieved 24 January 2007.
- ^ Premixed cement paste. Concreteinternational.com (1989-11-01). Retrieved on 2013-02-19.
- ^ Measuring, mixing, transporting and placing concrete. Concrete.org. Retrieved on 2013-02-19.
- ^ U.S. patent 5,443,313 – Method for producing construction mixture for concrete
- ^ Ferrari, L; Kaufmann, J; Winnefeld, F; Plank, J (2011). "Multi-method approach to study influence of superplasticizers on cement suspensions". Cement and Concrete Research. 41 (10): 1058. doi:10.1016/j.cemconres.2011.06.010.
- ^ "Concrete Testing". Retrieved 10 November 2008.
- ^ Resulting strength distribution in vertical elements researched and presented at the article "Concrete inhomogeneity of vertical cast-in-place elements in skeleton-type buildings".
- ^ "Structural lightweight concrete" (PDF). Concrete Construction. The Aberdeen Group. March 1981.
- ^ "Ordering Concrete by PSI". American Concrete. Retrieved 10 January 2013.
- ^ a b Henry G. Russel, PE. "Why Use High Performance Concrete?" (PDF). Technical Talk. Retrieved 10 January 2013.
- ^ "Concrete in Practice: What, Why, and How?" (PDF). NRMCA-National Ready Mixed Concrete Association. Retrieved 10 January 2013.
- ^ Geoffrey Michael Gadd (March 2010). "Metals, minerals and microbes: geomicrobiology and bioremediation". Microbiology. pp. 609–643.
- ^ Navdeep Kaur Dhami; Sudhakara M. Reddy; Abhijit Mukherjee. "Biofilm and Microbial Applications in Biomineralized Concrete". p. 143.
- ^ Navdeep Kaur Dhami; Sudhakara M. Reddy; Abhijit Mukherjee. "Biofilm and Microbial Applications in Biomineralized Concrete". p. 146.
- ^ Navdeep Kaur Dhami; Sudhakara M. Reddy; Abhijit Mukherjee. "Biofilm and Microbial Applications in Biomineralized Concrete". p. 147.
- ^ a b Navdeep Kaur Dhami; Sudhakara M. Reddy; Abhijit Mukherjee. "Biofilm and Microbial Applications in Biomineralized Concrete". p. 142.
- ^ Shepherd and Woskie. "Controlling Dust from Concrete Saw Cutting" (PDF). Journal of Occupational and Environmental Hygiene. Retrieved 14 June 2013.
- ^ a b Mass Concrete. (PDF) . Retrieved on 2013-02-19.
- ^ Lomborg, Bjørn (2001). The Skeptical Environmentalist: Measuring the Real State of the World. p. 138. ISBN 978-0-521-80447-9.
- ^ "Minerals commodity summary – cement – 2007". US United States Geological Survey. 1 June 2007. Retrieved 16 January 2008.
- ^ John Gajda (2001) Energy Use of Single Family Houses with Various Exterior Walls, Construction Technology Laboratories Inc.
- ^ "Features and Usage of Foam Concrete".
- ^ Mullapudi, T.R.S., Gao, D., and Ayoub, A.S., “Nondestructive Evaluation of Carbon-Nanofiber Concrete,” Magazine of Concrete Research, ICE, V. 65 (18), 2013, pp. 1081-1091. http://www.icevirtuallibrary.com/content/article/10.1680/macr.12.00187;jsessionid=1mejdtp8p7j4n.x-telford-live-01
- ^ Unreinforced Masonry Buildings and Earthquakes: Developing Successful Risk Reduction Programs, FEMA P-774 / October 2009
- ^ Seismic Retrofit Design Of Historic Century-Old School Buildings In Istanbul, Turkey, C.C. Simsir, A. Jain, G.C. Hart, and M.P. Levy, The 14th World Conference on Earthquake Engineering, 12–17 October 2008, Beijing, China
- ^ Sedimentary Rocks p. 7, msnucleus.org
- ^ Sustainable Development of Concrete Technology. (PDF) . Retrieved on 2013-02-19.
- ^ Concrete Structures Could Last 16,000 Years. Ecogeek.org. Retrieved on 2013-02-19.
- ^ Concrete Coating Considerations To Extend Performance Life. Facilitiesnet.com. Retrieved on 2013-02-19.
- ^ Self-Healing Concrete: Research Yields Cost-Effective System to Extend Life of Structures May 25, 2010
- ^ How long are dams like Hoover Dam engineered to last? What's the largest dam ever to fail?. Straightdope.com (2006-08-11). Retrieved on 2013-02-19.
- ^ "Itaipu Web-site". 2 January 2012. Retrieved 2 January 2012.
- ^ a b China’s Three Gorges Dam By The Numbers. Probeinternational.org. Retrieved on 2013-02-19.
- ^ "Concrete Pouring of Three Gorges Project Sets World Record". People’s Daily. 4 January 2001. Retrieved 24 August 2009.
- ^ "Concrete Pumping to 715 m Vertical – A New World Record Parbati Hydroelectric Project Inclined Pressure Shaft Himachal Pradesh – A case Study". The Masterbuilder. Retrieved 21 October 2010.
- ^ "SCHWING Stetter Launches New Truck mounted Concrete Pump S-36". NBM&CW (New Building Materials and Construction World). October 2009. Retrieved 21 October 2010.
- ^ "Concrete Supplier for Landmark Tower".
- ^ "The world record Concrete Supplier for Landmark Tower Unibeton Ready Mix".
- ^ Al Habtoor Engineering – Abu Dhabi – Landmark Tower has a record-breaking pour – September/October 2007, Page 7.
- ^ National Geographic Channel International / Caroline Anstey (2005), Megastructures: Petronas Twin Towers
- ^ "Continuous cast: Exxcel Contract Management oversees record concrete pour". US Concrete Products. 1 March 1998. Retrieved 25 August 2009.
- ^ Exxcel Project Management – Design Build, General Contractors. Exxcel.com. Retrieved on 2013-02-19.
- ^ Contractors Prepare to Set Gates to Close New Orleans Storm Surge Barrier May 12, 2011
- ^ Urbanite terminology
Bibliography
- Matthias Dupke: Textilbewehrter Beton als Korrosionsschutz. Diplomica Verlag, Hamburg 2010, ISBN 978-3-8366-9405-6.
External links
- Template:Dmoz
- Chemistry of Concrete at The Periodic Table of Videos (University of Nottingham)
- Refractory Concrete Information related to heat resistant concrete; recipes, ingredients mixing ratio, work with and applications.
- British Precast Concrete Federation
- Inhomogeneity of concrete strength distribution by volume of vertical monolithic (cast in situ) elements Reserves of concrete strength. Information may be used when design buildings against progressive failure.
- The History of Concrete