A trigger is a mechanism that actuates the firing sequence of a firearm, airgun, crossbow or speargun. A trigger may also start other non-shooting mechanisms such as a trap, a switch or a quick release. A small amount of energy applied to the trigger causes the release of much more energy.
In "double action" firearm designs, the trigger is also used to cock the firearm — and there are many designs where the trigger is used for a range of other functions. Although triggers usually consist of a lever actuated by the index finger, some such as the M2 Browning machine gun use the thumb, and others like the Springfield Armory M6 Scout use a "squeeze-bar trigger".
- 1 Function
- 2 Actions (mechanisms)
- 3 Variable triggers
- 4 References
- 5 External links
Firearms use triggers to initiate the firing of a cartridge in the firing chamber of the weapon. This is accomplished by actuating a striking device through a combination of spring and kinetic energy operating through a firing pin to strike and ignite the primer. There are two primary types of striking mechanisms, hammers and strikers. Hammers are spring-tensioned masses of metal that pivot on a pin when released and strike a firing pin to discharge a cartridge. Strikers are, essentially, spring-loaded firing pins that travel on an axis in-line with the cartridge eliminating the need for a separate hammer. The connection between the trigger and the hammer is typically referred to as the sear surface. Variable mechanisms will have this surface directly on the trigger and hammer or have separate sears or other connecting parts.
There are numerous types of actions, where action refers to the mechanism (the trigger, hammer, and safeties considered as a unit) or to the logic of how it is built and how it is used. They are categorized according to which functions the trigger is to perform. In addition to releasing the hammer or the striker, a trigger may cock the hammer or striker, rotate a revolver's cylinder, deactivate passive safeties, select between semi-automatic and full-automatic fire such as the Steyr AUG (see progressive trigger), or pre-set a "set trigger". Most modern firearms use the trigger to deactivate passive safeties but this does not change how they are identified.
A single-action (SA) trigger is the earliest and mechanically simplest of trigger types. It is called the "single-action" because it performs the single action of releasing the hammer or striker to discharge the firearm each time the trigger is pulled, while the hammer must be cocked by separate means. Almost all rifles and shotguns use this type of trigger (with certain exceptions, such as the Armsel Striker and certain law-enforcement Mossberg 590DA1 shotguns).
The term "single-action" was not in use until weapons with double-action triggers were invented, which did not occur until the mid-19th century; before that, all triggers were single-action (for example, all matchlocks, flintlocks, muskets, etc.). While originally all hammers required a separate hand motion to cock manually, with the birth of repeating rifles such as the Henry rifle, it was found to be easy to design the cocking of the hammer into the cycling of the action, which is still found in most modern repeating weapons, and some single-shots as well. Although these weapons do not require the user to physically cock the hammer, they are still single-actions because the cocking is not performed by the trigger mechanism. Manually-cocked triggers lasted much longer on revolvers; due to the limited size and weight of handguns, it was difficult to fit the necessary mechanisms in place, and most repeating rifles required the use of two hands to cycle the action. Thus the "classic" single-action revolver of the mid-to-late 19th century includes black-powder percussion-cap muzzleloaders such as the Colt 1860 "Army" Model, and Colt 1851 "Navy" Model, and European models like the LeMat, as well as early metallic-cartridge black-powder revolvers such as the Colt Model 1873 "Single Action Army" (named for its trigger mechanism) and Smith & Wesson Model 3, all of which required a thumb to cock the hammer before firing. Manually cocked hammers lasted a while longer in some break-action shotguns, and in dangerous game rifles, where the hunter did not want to rely on an unnecessarily complex or fragile weapon. While single-action revolvers never lost favor in the US right up until the birth of the semi-automatic pistol, double action revolvers, such as the Beaumont–Adams, were designed in Europe before the American Civil War broke out, and saw great popularity all through the latter half of the 19th century, with certain numbers being sold in the US as well.
In modern usage, the terms "single-action" and "double-action" almost always refer to handguns, as very few if any rifles or shotguns feature double-action triggers. While a "single-action" revolver or semi-automatic must always be cocked prior to firing (either manually or by the operation of the weapon), most "double-action" handguns are capable of firing in both single- and double-action modes. Only "double-action only" weapons are incapable of firing from a cocked hammer. It is a common misconception that "double action" refers to the ability to fire in both modes, but as stated above, the term stems from the number of actions performed by the trigger when pulled, not the operating modes it is capable of using.
While many European and some American revolvers were designed as double-action models throughout the late 19th century, for the first half of the 20th century, all semi-automatics were single-action weapons, requiring the weapon to be carried cocked with the safety on, or with an empty chamber (Colt M1911, Mauser C96, Luger P.08, Tokarev TT, Browning Hi-Power). The difference between these weapons and single-action revolvers is that while a single-action revolver requires the user to manually cock the hammer before firing, a single-action semi-automatic is automatically cocked when the user cycles the slide to chamber a round. Thereafter, every time a round is fired, the hammer is recocked by the cycling slide, and is thus always cocked unless the user manually lowers the hammer, or pulls the trigger on an empty chamber (weapons lacking automatic-hold-open feature only).
In the late 1930s and early 1940s, Walther introduced the first "double-action" semi-automatics, the PPK and P.38 models, which featured a revolver-style "double-action" trigger, allowing the weapon to be carried with a round chambered and the hammer lowered. After the first shot, they would fire as single-actions. These double action, or "double action/single action", pistols rapidly gained popularity, and the traditional single-action rapidly lost favor, although they still retain a dedicated following. Today, a "typical" revolver is a "double-action", which can be fired in single action when wished, and the most common form of semi-automatic is the "DA/SA", carried in double-action mode but firing most of its shots in single-action mode.
A double-action/single-action (DA/SA) firearm combines the features of both mechanisms. This action type is also known as traditional double-action (TDA).
The term "DA/SA" typically denotes a semi-automatic, while in a revolver, "double action" generally means a weapon combining the ability to fire both double- and single-action, as opposed to a plain single-action revolver.
In simple terms, "double-action" refers to a gun trigger mechanism that both cocks the hammer and then releases the sear, thus performing two actions, hence double action. However, although "double action" actually refers to a gun that cocks and releases the hammer with a trigger pull, in practice, most "double action" guns feature both single- and double-action abilities. This is opposed to "DAO" or "Double Action Only" firearms, which lack the ability to fire in single-action mode.
In a traditional double-action mechanism, the trigger mechanism has features that both allow the trigger to cock and release the hammer/striker when fully pulled, or to merely lock the hammer/striker in the cocked position when it is pulled to the rear and the trigger is not depressed. In a revolver, this means that simply squeezing the trigger when the hammer is lowered will both cock and release it. If the user uses their thumb to pull the hammer to the back, but doesn't press the trigger, the mechanism will lock the hammer in the cocked position until the trigger is pressed, just like a single action. Firing in double action mode gives greater rapidity of fire, but a longer, heavier trigger pull, which can limit accuracy compared to the lighter, shorter trigger pull of a single-action only handgun.
In a DA/SA semi-automatic handgun, the trigger mechanism functions identically to that of a DA revolver. However, this is combined with the ability of most semi-automatics to self-cock the hammer when firing. Thus, the weapon can be carried with the hammer down on a loaded chamber, reducing perceived danger of carrying a single-action semi-automatic. When the user is ready to fire, simply pulling the trigger, in double action mode, will cock and release the hammer. When the weapon fires, the cycling slide will automatically cock the hammer to the rear, meaning that the rest of the shots fired will be in single-action mode, unless the hammer is manually lowered again. This gives the positive aspects of a single-action trigger without the need to carry "cocked and locked" (with a loaded chamber and cocked hammer), or with an empty chamber, which requires the user to chamber a round before firing.
A potential drawback of a DA/SA weapon is that the shooter must master two different trigger pulls: the longer, heavier DA first pull and the shorter, lighter subsequent SA pulls. The difference between these trigger pulls can affect the accuracy of the crucial first few shots in an emergency situation. Although there is little need for a safety on a DA/SA handgun when carrying it loaded with the hammer down, after the first shots are fired, the hammer will be cocked and the chamber loaded. Thus, most DA/SA guns either feature a conventional safety that prevents the hammer from dropping, or a "decocker" - a lever that safely drops the hammer (i.e. decocks the gun) without fear of the gun firing. The latter is the more popular because, without a decocker, the user is forced to lower the hammer by hand onto a loaded chamber, with all of the attendant safety risks that involves, in order to return the gun to double-action mode. Revolvers almost never feature safeties, since they are traditionally carried un-cocked, and the hammer requires the user to physically cock it, unlike a DA/SA gun, which cocks itself every time the slide is cycled.
There are many examples of DA/SA semi-automatics, the Walther PPK being the first, followed up by the Walther P38. Modern examples include weapons such as the Beretta 92, among others. Almost all revolvers that are not specified as single-action models are capable of firing in both double- and single-action mode, for example, the Smith & Wesson Model 27, S&W Model 60, the Colt Police Positive, Colt Python, etc. Early double-action revolvers included the Beaumont–Adams and Tranter black-powder muzzleloaders. There are some revolvers that can only be fired in double-action mode (DAO), but that is almost always due to existing double-action/single-action models being modified so that the hammer cannot be cocked manually, rather than from weapons designed that way from the factory.
Double-action only 
A double-action, also known as double-action only (DAO) to prevent confusion with DA/SA designs, is a design which either has no internal sear mechanism capable of holding the hammer or striker in the cocked position (semi-automatics), or has the entire hammer shrouded and/or has the thumb spur machined off, preventing the user from cocking it (revolvers).
This design requires a trigger pull to both cock and trip the hammer/striker for every single shot, unlike a DA/SA, which only requires a double-action trigger pull for the first shot (or a typical DA/SA revolver, which can fire single action any time the user wishes, but uses double-action as a default). This means that there is no single-action function for any shot, and the hammer or striker always rests in the down position until the trigger pull begins. With semi-automatics, this means that unlike DA/SA weapons, the hammer does not remain cocked after the first round is fired, and every shot is in double-action mode. With revolvers, this means that one does not have the option of cocking the gun before shooting, and must always shoot it in double action mode.
Although there have been revolvers that were designed with trigger mechanisms totally lacking a single-action mechanism altogether, more commonly DAO revolvers are modifications of existing DA/SA models, with identical internals, only with access to the hammer prevented, either by covering it with a shroud or by removing the thumb spur. In both cases, the goal is to prevent the possible snagging of the hammer spur on clothing or holster. Due to the imposed limitation in accuracy, the majority of DAO revolvers have been short-barrel, close-range "snub" weapons, where rapidity of draw is essential and limited accuracy is already an acceptable compromise.
The purpose of a DAO action in a semi-automatic is mostly to avoid the change in trigger pull between the first and subsequent shots that one experiences in a DA/SA pistol, while avoiding the perceived danger of carrying a cocked single-action handgun, although it also avoids having to carry a cocked and loaded pistol, or having to lower the hammer on a loaded chamber, if one only fires a partial magazine. A good example of this action in a semi-automatic is the SIG Sauer DAK trigger, or the DAO action of the Sig P250. For striker-fired pistols such as the Taurus 24/7, the striker will remain in the rest position through the entire reloading cycle. This term applies most often to semi-automatic handguns; however, the term can also apply to some revolvers such as the Smith & Wesson Centennial, the Type 26 Revolver, and the Enfield No. 2 Mk I revolvers, in which there is no external hammer spur, or which simply lack the internal sear mechanism capable of holding the hammer in the cocked position.
A release trigger releases the hammer or striker when the trigger is released by the shooter, rather than when it is pulled. Release triggers are largely used on shotguns intended for trap and skeet shooting.
Pull and release trigger
A pull and release trigger, also called a bidirectional or binary trigger, is a trigger for a semiautomatic firearm that drops the hammer both when the trigger is pulled as well as when it is released. Examples for AR-15 rifles are produced by Franklin Armory, Fostech Outdoors and Liberty Gun Works. Liberty Gun Works' trigger only functions in pull and release mode, while the other two have three-position safety selectors. The third position (which would correspond to fully automatic on an M16 rifle) activates the pull and release mode, while the center selector position causes the trigger to only drop the hammer when pulled.
A set trigger allows a shooter to have a greatly reduced trigger pull (the resistance of the trigger) while maintaining a degree of safety in the field compared to having a conventional, very light trigger. There are two types: single set and double set. Set triggers are most likely to be seen on customized weapons and competition rifles where a light trigger pull is beneficial to accuracy.
Single set trigger
A single set trigger is usually one trigger that may be fired with a conventional amount of trigger pull weight or may be "set" – usually by pushing forward on the trigger, or by pushing forward on a small lever attached to the rear of the trigger. This takes up the trigger slack (or "take-up") in the trigger and allows for a much lighter trigger pull. This is colloquially known as a hair trigger.
Double set trigger
A double set trigger achieves the same result, but uses two triggers: one sets the trigger and the other fires the weapon. Double set triggers can be further classified by phase. A double set, single phase trigger can only be operated by first pulling the set trigger, and then pulling the firing trigger. A double set, double phase trigger can be operated as a standard trigger if the set trigger is not pulled, or as a set trigger by first pulling the set trigger. Double set, double phase triggers offer the versatility of both a standard trigger and a set trigger.
Pre-set (striker or hammer)
Pre-set strikers and hammers apply only to semi-automatic handguns. Upon firing a cartridge or loading the chamber, the hammer or striker will rest in a partially cocked position. The trigger serves the function of completing the cocking cycle and then releasing the striker or hammer. While technically two actions, it differs from a double-action trigger in that the trigger is not capable of fully cocking the striker or hammer. It differs from single-action in that if the striker or hammer were to release, it would generally not be capable of igniting the primer. Examples of pre-set strikers are the Glock, Smith & Wesson M&P, Springfield Armory XDS (only), Kahr Arms, FN FNS series and Ruger SR series pistols. This type of trigger mechanism is sometimes referred to as a Striker Fired Action or SFA. Examples of pre-set hammers are the Kel-Tec P-32 and Ruger LCP pistols.
Pre-set hybrid triggers are similar to a DA/SA trigger in reverse. The first pull of the trigger is pre-set. If the striker or hammer fail to discharge the cartridge, the trigger may be pulled again and will operate as a double-action only (DAO) until the cartridge discharges or the malfunction is cleared. This allows the operator to attempt a second time to fire a cartridge after a misfire malfunction, as opposed to a single-action, in which the only thing to do if a round fails to fire is to rack the slide, clearing the round and recocking the hammer. While this can be advantageous in that many rounds will fire on being struck a second time, and it is faster to pull the trigger a second time than to cycle the action, if the round fails to fire on the second strike, the user will be forced to clear the round anyway, thus using up even more time than if they had simply done so in the first place. The Taurus PT 24/7 Pro pistol (not to be confused with the first-generation 24/7 which was a traditional pre-set) offered this feature starting in 2006. The Walther P99 Anti-Stress is another example.
Each trigger mechanism has its own merits. Historically, the first type of trigger was the single-action. This is the simplest mechanism and generally the shortest, lightest, and smoothest pull available. The pull is also consistent from shot to shot so no adjustments in technique are needed for proper accuracy. On a single-action revolver, for which the hammer must be manually cocked prior to firing, an added level of safety is present. On a semi-automatic, the hammer will be cocked and made ready to fire by the process of chambering a round, and as a result an external safety is sometimes employed.
Double-action triggers provide the ability to fire the gun whether the hammer is cocked or uncocked. This feature is desirable for military, police, or self-defense pistols. The primary disadvantage of any double-action trigger is the extra length the trigger must be pulled and the extra weight required to overcome the spring tension of the hammer or striker.
DA/SA pistols are versatile mechanisms. These firearms generally have a manual safety that additionally may serve to decock the hammer. Some have a facility (generally a lever or button) to safely lower the hammer. As a disadvantage, these controls are often intermingled with other controls such as slide releases, magazine releases, take-down levers, takedown lever lock buttons, loaded chamber indicators, barrel tip-up levers, etc. These variables become confusing and require more complicated manuals-of-arms. One other disadvantage is the difference between the first double-action pull and subsequent single-action pulls.
DAO firearms resolve some DA/SA shortcomings by making every shot a double-action shot. Because there is no difference in pull weights, training and practice are simplified. Additionally, negligent discharges are mitigated due to a heavier trigger pull. This is a particular advantage for a police pistol. These weapons also generally lack any type of external safety. DAO is common among police agencies and for small, personal protection firearms. The primary drawback is that additional trigger pull weight and travel required for each shot reduce accuracy.
Pre-set triggers, only recently coming into vogue, offer a balance of pull weight, trigger travel, safety, and consistency. Glock popularized this trigger in modern pistols and many other manufacturers have released pre-set striker products of their own. The primary disadvantage is that pulling the trigger a second time after a failure to fire will not re-strike the primer. In normal handling of the firearm, this is not an issue; loading the gun requires that the slide be retracted, pre-setting the striker. Clearing a malfunction also usually involves retracting the slide following the "tap rack bang" procedure. Many similar approaches are argued for generally accomplishing the same end.
A double-crescent trigger provides select fire capability without the need for a fire mode selector switch. Pressing the upper segment of the trigger produced semi-automatic fire, while holding the lower segment of the trigger produced fully automatic fire. Though considered innovative at the time, the feature was eliminated on most firearms due to its complexity. Examples include MG 34, Kg m/40 light machine gun, M1946 Sieg automatic rifle, and Star Model Z-70.
Progressive/staged trigger 
A progressive, or staged trigger allows different firing rates based on how far it is depressed. For example, when pulled lightly, the weapon will fire a single shot. When depressed further, the weapon fires at a fully automatic rate. Examples include Jatimatic, CZ Model 25, PM-63, BXP, F1 submachine gun, Vigneron submachine gun, and Wimmersperg Spz-kr. and Steyr AUG.
- "Trigger Analysis". Ballistics-Experts.com. Archived from the original on February 11, 2003.
- U.S. Patent 2,027,950
- "Trigger Function and Terminology". Spencer, B. E. Archived from the original on 2011-07-20.
- "Trigger Options of the Semi-Automatic Service Pistol". Chuckhawks.com. Archived from the original on 2014-11-08.
- "Trigger mechanism providing a short burst of fire capability for submachine guns". freepatentsonline.com.