Diesel locomotive

These Pacific National-operated specimens show three styles of diesel locomotive body: box cab (rear), hood unit (center) and cab unit (front).

A diesel locomotive is a type of railway locomotive in which the prime mover is a diesel engine. Several types of diesel locomotive have been developed, differing mainly in the means by which mechanical power is conveyed to the driving wheels (drivers).

The InterCity 125, the current confirmed record holder as the fastest diesel-powered train at 148 mph (238 km/h); is made up of two power cars, one at each end of a fixed formation of carriages; capable of 125 mph (201 km/h) in regular service.

Twin-section diesel locomotive 2M62M-1198 (rebuilt with CAT engines), near Kyviškės, Lithuania.

Overview

Early internal combustion engine-powered locomotives and railmotors used gasoline as their fuel. Soon after Dr. Rudolf Diesel patented his first compression ignition engine in 1892, it was considered for railway propulsion. Progress was slow, however, as several problems had to be overcome.

Petrol-electric Weitzer railmotor, first 1903, series 1906

Power transmission was a primary concern. As opposed to steam and electric engines, internal combustion engines work efficiently only within a limited range of turning frequencies. In light vehicles, this could be overcome by a clutch. In heavy railway vehicles, mechanical transmission never worked well or wore out too soon. Experience with early gasoline powered locomotives and railcars was valuable for the development of diesel traction. One step towards diesel-electric transmission was the petrol-electric vehicle, such as the Acsev Weitzer railmotor, which could operate from batteries and electric overhead wires too. (1903 ff.)

Steady improvements in diesel design (many developed by Sulzer Ltd. of Switzerland, with whom Dr. Diesel was associated for a time) gradually reduced its physical size and improved its power-to-weight ratio to a point where one could be mounted in a locomotive. Once the concept of diesel-electric drive was accepted, the pace of development quickened, and by 1925 a small number of diesel locomotives of 600 horsepower were in service in the United States. In 1930, Armstrong Whitworth of the United Kingdom delivered two 1,200 hp locomotives using engines of Sulzer design to Buenos Aires Great Southern Railway of Argentina.

By the mid-1950s, with economic recovery from the Second World War, production of diesel locomotives had begun in many countries and the diesel locomotive was on its way to becoming the dominant type of locomotive. It offered greater flexibility and performance than the steam locomotive, as well as substantially lower operating and maintenance costs, other than where electric traction was in use due to policy decisions. Currently, almost all diesel locomotives are diesel-electric, although the diesel-hydraulic type was widely used between the 1950s and 1970s.

The Soviet diesel locomotive TEP80-0002 lays claim to the world speed record for a diesel railed vehicle, having reached 271 km/h (168 mph) on 5 October 1993.

History

Adaptation of the diesel engine for rail use

A WDM-3A diesel locomotive of Indian Railways, used to haul both passenger and freight.

A string of four diesel locomotives haul a long freight train in the U.S. state of Washington.

Earliest recorded examples of an internal combustion engine for railway use included a prototype designed by William Dent Priestman, which was examined by Sir William Thomson in 1888 who described it as a "[Priestman oil engine] mounted upon a truck which is worked on a temporary line of rails to show the adaptation of a petroleum engine for locomotive purposes.". In 1894, a 20 h.p. two axle machine built by Priestman Brothers was used on the Hull Docks. In 1896 an oil-engined railway locomotive was built for the Royal Arsenal, Woolwich, England, in 1896, using an engine designed by Herbert Akroyd Stuart. It was not, strictly, a diesel because it used a hot bulb engine (also known as a semi-diesel) but it was the precursor of the diesel.

Following the expiration of Dr. Rudolf Diesel’s patent in 1912, his engine design was successfully applied to marine propulsion and stationary applications. However, the massiveness and poor power-to-weight ratio of these early engines made them unsuitable for propelling land-based vehicles. Therefore, the engine's potential as a railroad prime mover was not initially recognized. This changed as development reduced the size and weight of the engine.

The world’s first diesel-powered locomotive was operated in the summer of 1912 on the Winterthur-Romanshorn Railroad in Switzerland, but was not a commercial success. In 1906, Rudolf Diesel, Adolf Klose and the steam and Diesel engine manufacturer Gebrüder Sulzer founded Diesel-Sulzer-Klose GmbH to manufacture Diesel-powered locomotives. Sulzer had been manufacturing Diesel engines since 1898. The Prussian State Railways ordered a Diesel locomotive from the company in 1909, and after test runs between Winterthur and Romanshorn the Diesel-mechanical locomotive was delivered in Berlin in September 1912. During further test runs in 1913 several problems were found. After the First World War broke out in 1914, all further trials were stopped. The locomotive weight was 95 tonnes and the power was 883 kW with a maximum speed of 100 km/h. Small numbers of prototype diesel locomotives were produced in a number of countries through the mid-1920s.

Advance of diesel traction in the US

Early American developments

Adolphus Busch purchased the American manufacturing rights for the Diesel engine in 1898 but never applied this new form of power to transportation. He founded the Busch-Sulzer company in 1911. Only limited success was achieved in the early twentieth century with direct-driven gasoline and Diesel powered railcars.

General Electric (GE) entered the railcar market in the early twentieth century, as Thomas Edison possessed a patent on the electric locomotive, his design actually being a type of electrically propelled railcar. GE built its first electric locomotive prototype in 1895. However, high electrification costs caused GE to turn its attention to Diesel power to provide electricity for electric railcars. Problems related to co-coordinating the Diesel engine and electric motor were immediately encountered, primarily due to limitations of the Ward Leonard electric elevator drive system that had been chosen.

A significant breakthrough occurred in 1914, when Hermann Lemp, a GE electrical engineer, developed and patented a reliable direct current electrical control system (subsequent improvements were also patented by Lemp). Lemp's design used a single lever to control both engine and generator in a coordinated fashion, and was the prototype for all diesel-electric locomotive control systems.

In 1917–18, GE produced three experimental diesel-electric locomotives using Lemp's control design, the first known to be built in the United States. Following this development, the 1923 Kaufman Act banned steam locomotives from New York City because of severe pollution problems. The response to this law was to electrify high-traffic rail lines. However, electrification was uneconomical to apply to lower-traffic areas.

The first regular use of diesel-electric locomotives was in switching (shunter) applications. General Electric produced several small switching locomotives in the 1930s (the famous "44-tonner" switcher was introduced in 1940) Westinghouse Electric and Baldwin collaborated to build switching locomotives starting in 1929. However, the Great Depression curtailed demand for Westinghouse’s electrical equipment, and they stopped building locomotives internally, opting to supply electrical parts instead.

First American series production locomotives

General Electric continued to be interested in developing a practical diesel railway locomotive, and approached Ingersoll-Rand in 1924. The resulting 300 horsepower locomotive was fitted with an electrical generator and traction motors supplied by GE, as well as a form of Lemp's control system, and was delivered in July 1925. This locomotive demonstrated that the diesel-electric power unit could provide many of the benefits of an electric locomotive without the railroad having to bear the sizeable expense of electrification. The unit successfully demonstrated—in switching, road freight and passenger service—on a baker’s dozen of railroads, and became the prototype for 33 units of 600 horsepower AGEIR boxcab switching locomotives built by a consortium of GE, I-R and the American Locomotive Company for several New York City railroads.

In June 1925, Baldwin Locomotive Works outshopped a prototype diesel-electric locomotive for "special uses" (such as for runs where water for steam locomotives was scarce) using electrical equipment from Westinghouse Electric Company. Its twin-engine design was not successful, and the unit was scrapped after a short testing and demonstration period. Industry sources were beginning to suggest “the outstanding advantages of this new form of motive power”. In 1929, the Canadian National Railways became the first North American railway to use diesels in mainline service with two units, 9000 and 9001, from Westinghouse.

Diesel-electric railroad locomotion entered the American mainstream when the Burlington Railroad and Union Pacific used Diesel "streamliners" to haul passengers, both since 1934. Following the successful 1939 tour of General Motors' EMD's FT demonstrator freight locomotive set, the transition from steam to Diesel power began, the pace substantially quickening in the years following the close of World War II. Fairbanks-Morse developed a unique opposed-piston engine that was used in their locomotives, as well as in submarines.

Early diesel-electric locomotives in the United States used direct current (DC) traction motors, but alternating current (AC) motors came into widespread use in the 1990s, starting with the Electro-Motive SD70MAC in 1993 and followed by the General Electric's AC4400CW in 1994 and AC6000CW in 1995.

Early diesel locomotives and railcars in Europe

Swiss & German co-production: world's first functional diesel-electric railcar 1914

First functional diesel vehicles

In 1914, world's first functional diesel-electric railcars were produced for the Königlich-Sächsische Staatseisenbahnen (Royal Saxon State Railways) by Waggonfabrik Rastatt with electric equipment from Brown, Boveri & Cie and diesel engines from Swiss Sulzer AG. They were classified as DET 1 and DET 2 (de.wiki). Due to shortage of petrol products during World War I, they remained unused for regular service in Germany. In 1922, they were sold to Swiss Compagnie du Chemin de fer Régional du Val-de-Travers (fr.wiki), where they were used in regular service up to the electrification of the line in 1944. Afterwards, the company kept them in service as boosters till 1965.

Fiat claims a first Italian diesel-electric locomotive built in 1922, but little detail is available. A Fiat-TIBB diesel-locomotive "A", of 440CV, is reported to have entered service on the Ferrovie Calabro Lucane in southern Italy in 1926, following trials in 1924-5.

World's first useful diesel locomotive for long distances SŽD Eel2, 1924 in Kiev

In 1924, two diesel-electric locomotives were taken in service by the Soviet railways, almost at one time:

• The engine Э^эл2 (E^el2 original number Юэ 001/Yu-e 001) started on October 22. It had been designed by a team led by Yuri Lomonosov and built 1923–1924 by Maschinenfabrik Esslingen in Germany. It had 5 driving axles (1'E1'). After several test rides, it hauled trains for almost three decades from 1925 to 1954. Though proved to be world's first functional diesel locomotive, it didn't become a series. But it became a model for several classes of Soviet diesel locomotives. (see also Category:Diesel locomotives of Russia)
• The engine Щэл1 (Shch-el 1, original number Юэ2/Yu-e 2), started on November 9. It had been developed by Yakov Modestovich Gakkel (ru.wiki) and built by Baltic Shipyard in Saint Petersburg. It had ten driving axles in three bogies (1' Co' Do' Co' 1'). From 1925 to 1927, it hauled trains between Moscow and Kursk and in Caucasus region. Due to technical problems, afterwards it was out of service. Since 1934, it was used as a stationary electric generator.

In 1935, Krauss-Maffei, MAN and Voith built the first diesel-hydraulic locomotive, called V 140, in Germany. The German railways (DRG) being very pleased with the performance of that engine, diesel-hydraulics became the mainstream in diesel locomotives in Germany. Serial production of diesel locomotives in Germany began after World War II.

Switchers

Shunter of Nederlandse Spoorwegen from 1934, in modern livery

In many railway stations and industrial compounds, steam shunters had to be kept hot during lots of lazy breaks between scattered short tasks. Therefore, diesel traction became economic for shunting, before it became economic for hauling trains. The construction of diesel shunters began in 1920 in France, in 1925 in Denmark, in 1926 in the Netherlands, and in 1927 in Germany. After few years of testing, hundreds of units were produced within a decade.

Diesel railcars for regional traffic

Renault VH, France, 1933/34

Diesel-powered or "oil-engined" railcars, generally diesel-mechanical, were developed by various European manufacturers in the 1930s, e.g. by William Beardmore and Company for the Canadian National Railways (the Beardmore Tornado engine was subsequently used in the R101 airship). Some of those series for regional traffic were begun with gasoline motors and then continued with diesel motors, such as Hungarian BC^mot (The class code doesn't tell anything but "railmotor with 2nd and 3rd class seats".), 128 cars built 1926 – 1937, or German Wismar railbuses (57 cars 1932 – 1941). In France, the first diesel railcar was Renault VH, 115 units produced 1933/34. In Italy, after 6 Gasoline cars since 1931, Fiat and Breda built a lot of diesel railmotors, more than 110 from 1933 to 1938 and 390 from 1940 to 1953, Class 772 known as Littorina, and Class ALn 900.

High speed railcars

In the 1930s, streamlined highspeed diesel railcars were developed in several countries:

• In Germany, the Flying Hamburger was built in 1932. After a test ride in December 1932, this two coach diesel railcar (in English terminology a DMU2) started service at Deutsche Reichsbahn (DRG) in February 1933. It became the prototype of DRG Class SVT 137 with 33 more highspeed DMUs, built for DRG till 1938, 13 DMU 2 ("Hamburg" series), 18 DMU 3 ("Leipzig" and "Köln" series), and 2 DMU 4 ("Berlin" series).
• French SNCF classes XF 1000 and XF 1100 comprised 11 high speed DMUs, also called TAR, built 1934–1939.
• In Hungary, Ganz Works built Arpád railmotor (see hu.wiki and de.wiki), a kind of a luxurious railbus in a series of 7 items since 1934, and started to build Hargita DMU amazingly in 1944 (see hu.wiki)

Diesel overcomes steam

British Rail Class D16/1, since 1948

Diesel locomotives in Oldenburg, Germany

In 1945, a batch of 30 Baldwin diesel-electric locomotives, Baldwin 0-6-6-0 1000, was delivered from the United States to the railways of the Soviet Union.

In 1947, the London Midland & Scottish Railway introduced the first of a pair of 1,600 hp Co-Co diesel-electric locomotives (later British Rail Class D16/1) for regular use in the United Kingdom, although British manufacturers such as Armstrong Whitworth had been exporting diesel locomotives since 1930. Fleet deliveries to British Railways, of other designs such as Class 20 and Class 31, began in 1957.

Series production of diesel locomotives in Italy began in the mid-1950s. Generally, diesel traction in Italy was of less importance than in other countries, as it was amongst the most advanced countries in electrification of the main lines and, as a result of Italian geography, even on many domestic connections freight transport over sea is cheaper than rail transport.

Early diesel locomotives and railcars in Asia

Japan

In Japan, since the 1920s, some petrol-electric railcars were produced. The first diesel-electric traction and the first air-streamed vehicles on Japanese rails were the two DMU3s of class Kiha 43000 (キハ43000系) Japan's first series of diesel locomotives was class DD50 (国鉄DD50形デ), twin locomotives, developed since 1950 and in service since 1953.

China

One of the first home developed diesel vehicles of China was the DMU Dongfeng (东风), produced in 1958 by CSR Sifang. Series production of China's first diesel locomotive class, the DFH 1, began in 1964 following construction of a prototype in 1959.

Early diesel locomotives and railcars in Australia

The Trans-Australian Railway built 1912 to 1917 by Commonwealth Railways (CR) passes through 2000 km of waterless (or salt watered) desert terrain unsuitable for steam locomotives. The original engineer Henry Deane envisaged diesel operation to overcome such problems. Some have suggested that the CR worked with the South Australian Railways to trial diesel traction. However, the technology was not developed enough to be reliable.

As in Europe, the usage of internal combustion engines advanced more readily in self-propelled railcars than in locomotives.

• Some Australian railway companies bought McKeen railcars.
• In the 1920s and 1930s, more reliable Gasoline railmotors were built by Australian industries.
• Australia's first diesel railcars were NSWGR 400 & 500 Class in 1938.
• High speed vehicles for those days' possibilities on 3 ft 6 in (1,067 mm) were the 10 Vulcan railcars of 1940 for New Zealand.

Diesel’s advantages over steam

Diesel engines slowly eclipsed those powered by steam as the manufacturing and operational efficiencies of the former made them cheaper to own and operate. While initial costs of diesel engines were high, steam locomotives were custom-made for specific railway routes and lines and, as such, economies of scale were difficult to achieve. Though more complex to produce with exacting manufacturing tolerances (1⁄10000-inch (0.0025 mm) for diesel, compared with 1⁄100-inch (0.25 mm) for steam), diesel locomotive parts were more conducive to mass production. While the steam engine manufacturer Baldwin offered almost five hundred steam models in its heyday, EMD offered fewer than ten diesel varieties.

Diesel locomotives offer significant operating advantages over steam locomotives. They can safely be operated by one person, making them ideal for switching/shunting duties in yards (although for safety reasons many main-line diesel locomotives continue to have 2-man crews: an engineer and a conductor/switchman) and the operating environment is much more attractive, being much quieter, fully weatherproof and without the dirt and heat that is an inevitable part of operating a steam locomotive. Diesel locomotives can be worked in multiple with a single crew controlling multiple locomotives throughout a single train—something not practical with steam locomotives. This brought greater efficiencies to the operator, as individual locomotives could be relatively low-powered for use as a single unit on light duties but marshaled together to provide the power needed on a heavy train still under the control of a single crew. With steam traction a single very powerful and expensive locomotive was required for the heaviest trains or the operator resorted to double heading with multiple locomotives and crews, a method which was also expensive and brought with it its own operating difficulties.

Diesel engines can be started and stopped almost instantly, meaning that a diesel locomotive has the potential to incur no costs when not being used. However, it is still the practice of large North American railroads to use straight water as a coolant in diesel engines instead of coolants that incorporate anti-freezing properties; this results in diesel locomotives being left idling when parked in cold climates instead of being completely shut down. Still, a diesel engine can be left idling unattended for hours or even days, especially since practically every diesel engine used in locomotives has systems that automatically shut the engine down if problems such as a loss of oil pressure or coolant loss occur. In recent years, automatic start/stop systems such as SmartStart have been adopted, which monitor coolant and engine temperatures. When these temperatures show that the unit is close to having its coolant freeze, the system restarts the diesel engine to warm the coolant and other systems.

Steam locomotives, by comparison, require intensive maintenance, lubrication, and cleaning before, during, and after use. Preparing and firing a steam locomotive for use from cold can take many hours, although it may be kept in readiness between uses with a small fire to maintain a slight heat in the boiler, but this requires regular stoking and frequent attention to maintain the level of water in the boiler. This may be necessary to prevent the water in the boiler freezing in cold climates, so long as the water supply itself is not frozen.

Moreover, maintenance and operational costs of steam locomotives were much higher than diesel counterparts even though it took diesel locomotives almost 50 years to reach the same power output that steam locomotives could achieve at their technological height. Annual maintenance costs for steam locomotives accounted for 25% of the initial purchase price. Spare parts were cast from wooden masters for specific locomotives. The sheer number of unique steam locomotives meant that there was no feasible way for spare-part inventories to be maintained. With diesel locomotives spare parts could be mass-produced and held in stock ready for use and many parts and sub-assemblies could be standardised across an operator's fleet using different models of locomotive from the same builder. Parts could be interchanged between diesel locomotives of the same or similar design, reducing down-time; for example, a locomotive's faulty prime mover may be removed and quickly replaced with another spare unit, allowing the locomotive to return to service whilst the original prime mover is repaired (and which can in turn be held in reserve to be fitted to another locomotive). Repair or overhaul of the main workings of a steam locomotive required the locomotive to be out of service for as long as it took for the work to be carried out in full.

Steam engines also required large quantities of coal and water, which were expensive variable operating costs. Further, the thermal efficiency of steam was considerably less than that of diesel engines. Diesel’s theoretical studies demonstrated potential thermal efficiencies for a compression ignition engine of 36% (compared with 6–10% for steam), and an 1897 one-cylinder prototype operated at a remarkable 26% efficiency.

However, one study published in 1959 suggested that many of the comparisons between diesel and steam locomotives were made unfairly mostly because diesels were newer. After painstaking analysis of financial records and technological progress, the author found that if research had continued on steam technology instead of diesel, there would be negligible financial benefit in converting to diesel locomotion.

By the mid-1960s, diesel locomotives had effectively replaced steam locomotives where electric traction was not in use. Attempts to develop Advanced steam technology continue in the 21st century but have not made a significant impact.

Transmission types

Unlike steam engines, internal combustion engines require a transmission to power the wheels. The engine must be allowed to continue to run when the locomotive is stopped.

Diesel-mechanical

A British Rail Class 03 diesel-mechanical shunter (switcher) with a jackshaft under the cab.

A diesel-mechanical locomotive uses a mechanical transmission in a fashion similar to that employed in most road vehicles. This type of transmission is generally limited to low-powered, low speed shunting (switching) locomotives, lightweight multiple units and self-propelled railcars.

Schematic illustration of a diesel mechanical locomotive

The mechanical transmissions used for railroad propulsion are generally more complex and much more robust than standard-road versions. There is usually a fluid coupling interposed between the engine and gearbox, and the gearbox is often of the epicyclic (planetary) type to permit shifting while under load. Various systems have been devised to minimise the break in transmission during gear changing; e.g., the S.S.S. (synchro-self-shifting) gearbox used by Hudswell Clarke.

Diesel-mechanical propulsion is limited by the difficulty of building a reasonably sized transmission capable of coping with the power and torque required to move a heavy train. A number of attempts to use diesel-mechanical propulsion in high power applications have been made (e.g., the 1,500 kW (2000 horsepower) British Rail 10100 locomotive), although none have proved successful in the end.

Diesel-electric

For locomotives powered by both external electricity and diesel fuel, see electro-diesel below. For locomotives powered by a combination of diesel or fuel cells and batteries or ultracapacitors, see hybrid locomotive.

Schematic diagram of diesel electric locomotive

In a diesel-electric locomotive, the diesel engine drives either an electrical DC generator (generally, less than 3,000 horsepower (2,200 kW) net for traction), or an electrical AC alternator-rectifier (generally 3,000 horsepower (2,200 kW) net or more for traction), the output of which provides power to the traction motors that drive the locomotive. There is no mechanical connection between the diesel engine and the wheels.

The important components of diesel-electric propulsion are the diesel engine (also known as the prime mover), the main generator/alternator-rectifier, traction motors (usually with four or six axles), and a control system consisting of the engine governor and electrical and/or electronic components, including switchgear, rectifiers and other components, which control or modify the electrical supply to the traction motors. In the most elementary case, the generator may be directly connected to the motors with only very simple switchgear.

The EMD F40PH (left) and MPI MPXpress-series MP36PH-3S (right) locomotives coupled together by Metra use diesel-electric transmission.

Soviet 2TE10U locomotive

Originally, the traction motors and generator were DC machines. Following the development of high-capacity silicon rectifiers in the 1960s, the DC generator was replaced by an alternator using a diode bridge to convert its output to DC. This advance greatly improved locomotive reliability and decreased generator maintenance costs by elimination of the commutator and brushes in the generator. Elimination of the brushes and commutator, in turn, disposed of the possibility of a particularly destructive type of event referred to as a flashover, which could result in immediate generator failure and, in some cases, start an engine room fire.

Current North American practice is for four axles for high-speed passenger or "time" freight, or for six axles for lower-speed or "manifest" freight.

In the late 1980s, the development of high-power variable-frequency/variable-voltage (VVVF) drives, or "traction inverters," has allowed the use of polyphase AC traction motors, thus also eliminating the motor commutator and brushes. The result is a more efficient and reliable drive that requires relatively little maintenance and is better able to cope with overload conditions that often destroyed the older types of motors.

Engineer's controls in a diesel-electric locomotive cab. The lever near bottom-centre is the throttle and the lever visible at bottom left is the automatic brake valve control.

Diesel-electric control

MLW model S-3 produced in 1957 for the CPR adhering to designs by ALCO.

A diesel-electric locomotive's power output is independent of road speed, as long as the unit’s generator current and voltage limits are not exceeded. Therefore, the unit's ability to develop tractive effort (also referred to as drawbar pull or tractive force, which is what actually propels the train) will tend to inversely vary with speed within these limits. (See power curve below). Maintaining acceptable operating parameters was one of the principal design considerations that had to be solved in early diesel-electric locomotive development and, ultimately, led to the complex control systems in place on modern units.

Throttle operation

An EMD 12-567B Roots-blown 12-cylinder diesel engine (square "hand holes"), stored pending rebuild, and missing some components, most notably the two Roots blowers, with a 16-567C or D 16-cylinder engine (round "hand holes")

Cab of the Russian locomotive 2TE116U, 11 — throttle

The prime mover's power output is primarily determined by its rotational speed (RPM) and fuel rate, which are regulated by a governor or similar mechanism. The governor is designed to react to both the throttle setting, as determined by the engine driver and the speed at which the prime mover is running.

Locomotive power output, and thus speed, is typically controlled by the engine driver using a stepped or "notched" throttle that produces binary-like electrical signals corresponding to throttle position. This basic design lends itself well to multiple unit (MU) operation by producing discrete conditions that assure that all units in a consist respond in the same way to throttle position. Binary encoding also helps to minimize the number of trainlines (electrical connections) that are required to pass signals from unit to unit. For example, only four trainlines are required to encode all possible throttle positions.

North American locomotives, such as those built by EMD or General Electric, have nine throttle positions, one idle and eight power (as well as an emergency stop position that shuts down the prime mover). Many UK-built locomotives have a ten-position throttle. The power positions are often referred to by locomotive crews as "run 3" or "notch 3", depending upon the throttle setting.

In older locomotives, the throttle mechanism was ratcheted so that it was not possible to advance more than one power position at a time. The engine driver could not, for example, pull the throttle from notch 2 to notch 4 without stopping at notch 3. This feature was intended to prevent rough train handling due to abrupt power increases caused by rapid throttle motion ("throttle stripping," an operating rules violation on many railroads). Modern locomotives no longer have this restriction, as their control systems are able to smoothly modulate power and avoid sudden changes in train loading regardless of how the engine driver operates the controls.

When the throttle is in the idle position, the prime mover will be receiving minimal fuel, causing it to idle at low RPM. In addition, the traction motors will not be connected to the main generator and the generator's field windings will not be excited (energized) — the generator will not produce electricity with no excitation. Therefore, the locomotive will be in "neutral". Conceptually, this is the same as placing an automobile's transmission into neutral while the engine is running.

To set the locomotive in motion, the reverser control handle is placed into the correct position (forward or reverse), the brake is released and the throttle is moved to the run 1 position (the first power notch). An experienced engine driver can accomplish these steps in a coordinated fashion that will result in a nearly imperceptible start. The positioning of the reverser and movement of the throttle together is conceptually like shifting an automobile's automatic transmission into gear while the engine is idling

Placing the throttle into the first power position will cause the traction motors to be connected to the main generator and the latter's field coils to be excited. With excitation applied, the main generator will deliver electricity to the traction motors, resulting in motion. If the locomotive is running "light" (that is, not coupled to the rest of a train) and is not on an ascending grade, it will easily accelerate. On the other hand, if a long train is being started, the locomotive may stall as soon as some of the slack has been taken up, as the drag imposed by the train will exceed the tractive force being developed. An experienced engine driver will be able to recognize an incipient stall and will gradually advance the throttle as required to maintain the pace of acceleration.

As the throttle is moved to higher power notches, the fuel rate to the prime mover will increase, resulting in a corresponding increase in RPM and horsepower output. At the same time, main generator field excitation will be proportionally increased to absorb the higher power. This will translate into increased electrical output to the traction motors, with a corresponding increase in tractive force. Eventually, depending on the requirements of the train's schedule, the engine driver will have moved the throttle to the position of maximum power and will maintain it there until the train has accelerated to the desired speed.

As will be seen in the following discussion, the propulsion system is designed to produce maximum traction motor torque at start-up, which explains why modern locomotives are capable of starting trains weighing in excess of 15,000 tons, even on ascending grades. Current technology allows a locomotive to develop as much as 30 percent of its loaded driver weight in tractive force, amounting to some 120,000 pounds-force (530 kN) of drawbar pull for a large, six-axle freight (goods) unit. In fact, a consist of such units can produce more than enough drawbar pull at start-up to damage or derail cars (if on a curve) or break couplers (the latter being referred to in North American railroad slang as "jerking a lung"). Therefore, it is incumbent upon the engine driver to carefully monitor the amount of power being applied at start-up to avoid damage. In particular, "jerking a lung" could be a calamitous matter if it were to occur on an ascending grade, except that the safety inherent in the correct operation of automatic train brakes installed in wagons today, prevents runaway trains by automatically applying the wagon brakes when train line air pressure drops.

Propulsion system operation

Typical main generator constant power curve at "notch 8"

Left corridore of power compartment of Russian locomotive 2TE116U, 3 — alternator, 4 — rectifier, 6 — diesel

Ar locomotive's control system is designed so that the main generator electrical power output is matched to any given engine speed. Given the innate characteristics of traction motors, as well as the way in which the motors are connected to the main generator, the generator will produce high current and low voltage at low locomotive speeds, gradually changing to low current and high voltage as the locomotive accelerates. Therefore, the net power produced by the locomotive will remain constant for any given throttle setting (see power curve graph for notch 8).

In older designs, the prime mover's governor and a companion device, the load regulator, play a central role in the control system. The governor has two external inputs: requested engine speed, determined by the engine driver's throttle setting, and actual engine speed (feedback). The governor has two external control outputs: fuel injector setting, which determines the engine fuel rate, and load regulator position, which affects main generator excitation. The governor also incorporates a separate overspeed protective mechanism that will immediately cut off the fuel supply to the injectors and sound an alarm in the cab in the event the prime mover exceeds a defined RPM. Not all of these inputs and outputs are necessarily electrical.

The load regulator is essentially a large potentiometer that controls the main generator power output by varying its field excitation and hence the degree of loading applied to the engine. The load regulator's job is relatively complex, because although the prime mover's power output is proportional to RPM and fuel rate, the main generator's output is not (which characteristic was not correctly handled by the Ward Leonard elevator- and hoist-type drive system that was initially tried in early locomotives). Instead, a quite complex electro-hydraulic Woodward governor was employed. Today, this important function would be performed by the Engine control unit, itself being a part of the Locomotive control unit.

As the load on the engine changes, its rotational speed will also change. This is detected by the governor through a change in the engine speed feedback signal. The net effect is to adjust both the fuel rate and the load regulator position so that engine RPM and torque (and thus power output) will remain constant for any given throttle setting, regardless of actual road speed.

In newer designs controlled by a “traction computer,” each engine speed step is allotted an appropriate power output, or “kW reference”, in software. The computer compares this value with actual main generator power output, or “kW feedback”, calculated from traction motor current and main generator voltage feedback values. The computer adjusts the feedback value to match the reference value by controlling the excitation of the main generator, as described above. The governor still has control of engine speed, but the load regulator no longer plays a central role in this type of control system. However, the load regulator is retained as a “back-up” in case of engine overload. Modern locomotives fitted with electronic fuel injection (EFI) may have no mechanical governor; however a “virtual” load regulator and governor are retained with computer modules.

Traction motor performance is controlled either by varying the DC voltage output of the main generator, for DC motors, or by varying the frequency and voltage output of the VVVF for AC motors. With DC motors, various connection combinations are utilized to adapt the drive to varying operating conditions.

At standstill, main generator output is initially low voltage/high current, often in excess of 1000 amperes per motor at full power. When the locomotive is at or near standstill, current flow will be limited only by the DC resistance of the motor windings and interconnecting circuitry, as well as the capacity of the main generator itself. Torque in a series-wound motor is approximately proportional to the square of the current. Hence, the traction motors will produce their highest torque, causing the locomotive to develop maximum tractive effort, enabling it to overcome the inertia of the train. This effect is analogous to what happens in an automobile automatic transmission at start-up, where it is in first gear and thus producing maximum torque multiplication.

As the locomotive accelerates, the now-rotating motor armatures will start to generate a counter-electromotive force (back EMF, meaning the motors are also trying to act as generators), which will oppose the output of the main generator and cause traction motor current to decrease. Main generator voltage will correspondingly increase in an attempt to maintain motor power, but will eventually reach a plateau. At this point, the locomotive will essentially cease to accelerate, unless on a downgrade. Since this plateau will usually be reached at a speed substantially less than the maximum that may be desired, something must be done to change the drive characteristics to allow continued acceleration. This change is referred to as "transition," a process that is analogous to shifting gears in an automobile.

Transition methods include:

• Series / Parallel or "motor transition".
  • Initially, pairs of motors are connected in series across the main generator. At higher speed, motors are reconnected in parallel across the main generator.
• "Field shunting", "field diverting", or "weak fielding".
  • Resistance is connected in parallel with the motor field. This has the effect of increasing the armature current, producing a corresponding increase in motor torque and speed.

Both methods may also be combined, to increase the operating speed range.

• Generator / rectifier transition
  • Reconnecting the two separate internal main generator stator windings of two rectifiers from parallel to series to increase the output voltage.

In older locomotives, it was necessary for the engine driver to manually execute transition by use of a separate control. As an aid to performing transition at the right time, the load meter (an indicator that informs the engine driver on how much current is being drawn by the traction motors) was calibrated to indicate at which points forward or backward transition should take place. Automatic transition was subsequently developed to produce better operating efficiency, and to protect the main generator and traction motors from overloading from improper transition.

Modern locomotives incorporate traction inverters, AC to DC, with the capability to deliver 1,200 volts (earlier traction generators, DC to DC, had the capability to deliver only 600 volts). This improvement was accomplished largely through improvements in silicon diode technology. With the capability to deliver 1,200 volts to the traction motors, the necessity for "transition" was eliminated.

Dynamic braking

Main article: Dynamic brake

A common option on diesel-electric locomotives is dynamic (rheostatic) braking.

Dynamic braking takes advantage of the fact that the traction motor armatures are always rotating when the locomotive is in motion and that a motor can be made to act as a generator by separately exciting the field winding. When dynamic braking is utilized, the traction control circuits are configured as follows:

• The field winding of each traction motor is connected across the main generator.
• The armature of each traction motor is connected across a forced-air-cooled resistance grid (the dynamic braking grid) in the roof of the locomotive's hood.
• The prime mover RPM is increased and the main generator field is excited, causing a corresponding excitation of the traction motor fields.

The aggregate effect of the above is to cause each traction motor to generate electric power and dissipate it as heat in the dynamic braking grid. A fan connected across the grid provides forced-air cooling. Consequently, the fan is powered by the output of the traction motors and will tend to run faster and produce more airflow as more energy is applied to the grid.

Ultimately, the source of the energy dissipated in the dynamic braking grid is the motion of the locomotive as imparted to the traction motor armatures. Therefore, the traction motors impose drag and the locomotive acts as a brake. As speed decreases, the braking effect decays and usually becomes ineffective below approximately 16 km/h (10 mph), depending on the gear ratio between the traction motors and axles.

Dynamic braking is particularly beneficial when operating in mountainous regions; where there is always the danger of a runaway due to overheated friction brakes during descent (see also comments in the air brake article regarding loss of braking due to improper train handling). In such cases, dynamic brakes are usually applied in conjunction with the air brakes, the combined effect being referred to as blended braking. The use of blended braking can also assist in keeping the slack in a long train stretched as it crests a grade, helping to prevent a "run-in", an abrupt bunching of train slack that can cause a derailment. Blended braking is also commonly used with commuter trains to reduce wear and tear on the mechanical brakes that is a natural result of the numerous stops such trains typically make during a run.

Electro-diesel

Metro-North's GE Genesis P32AC-DM electro-diesel locomotive can also operate off of third-rail electrification.

Main article: Electro-diesel locomotive

These special locomotives can operate as an electric locomotive or as a diesel locomotive. The Long Island Rail Road, Metro-North Railroad and New Jersey Transit Rail Operations operate dual-mode diesel-electric/third-rail (catenary on NJTransit) locomotives between non-electrified territory and New York City because of a local law banning diesel-powered locomotives in Manhattan tunnels. For the same reason, Amtrak operates a fleet of dual-mode locomotives in the New York area. British Rail operated dual diesel-electric/electric locomotives designed to run primarily as electric locomotives with reduced power available when running on diesel power. This allowed railway yards to remain un-electrified, as the third rail power system is extremely hazardous in a yard area.

Diesel-hydraulic

Diesel-hydraulic locomotives use one or more torque converters, in combination with gears, with a mechanical final drive to convey the power from the diesel engine to the wheels.

Hydrostatic transmission systems are also used in some rail applications, primarily low speed shunting and rail-maintenance vehicles.

Hydrokinetic transmission

See also: Torque converter and Fluid coupling

DB class V 200 diesel-hydraulic

A Henschel (Germany) diesel-hydraulic locomotive in Medan, North Sumatra

Hydrokinetic transmission (also called hydrodynamic transmission) uses a torque converter. A torque converter consists of three main parts, two of which rotate, and one (the stator) that has a lock preventing backwards rotation and adding output torque by redirecting the oil flow at low output RPM. All three main parts are sealed in an oil-filled housing. To match engine speed to load speed over the entire speed range of a locomotive some additional method is required to give sufficient range. One method is to follow the torque converter with a mechanical gearbox which switches ratios automatically, similar to an automatic transmission on a car. Another method is to provide several torque converters each with a range of variability covering part of the total required; all the torque converters are mechanically connected all the time, and the appropriate one for the speed range required is selected by filling it with oil and draining the others. The filling and draining is carried out with the transmission under load, and results in very smooth range changes with no break in the transmitted power.

Passenger Multiple units

Diesel-hydraulic drive is common in multiple units, with various transmission designs used including Voith torque converters, and fluid couplings in combination with mechanical gearing.

The majority of British Rail's second generation passenger DMU stock used hydraulic transmission.

In the 21st century designs using hydraulic transmission include Bombardier's Turbostar, Talent, RegioSwinger families; diesel engined versions of Siemens's Desiro platform, and the Stadler Regio-Shuttle.

Locomotives

British Rail diesel-hydraulic locomotives: Class 52 "Western", Class 42 "Warship" and Class 35 "Hymek"

Diesel-hydraulic locomotives are less efficient than diesel-electrics. The first-generation BR diesel hydraulics were significantly less efficient (c. 65%) than diesel electrics (c. 80%) — moreover initial versions were found in many countries to be mechanically more complicated and more likely to break down. Hydraulic transmission for locomotives was developed in Germany. There is still debate over the relative merits of hydraulic vs. electrical transmission systems: advantages claimed for hydraulic systems include lower weight, high reliability, and lower capital cost.

By the 21st century, for diesel locomotive traction worldwide the majority of countries used diesel-electric designs, with diesel hydraulic designs not found in use outside Germany and Japan, and some neighbouring states, where it is used in designs for freight work.

In Germany and Finland, diesel-hydraulic systems have achieved high reliability in operation. In the UK the diesel-hydraulic principle gained a poor reputation due to the poor durability and reliability of the Maybach Mekydro hydraulic transmission. Argument continues over the relative reliability of hydraulic systems, with questions over whether data has been manipulated to favour local suppliers over non-German ones.

Examples

See also: Category:Diesel-hydraulic locomotives

A VR Class Dv12 diesel-hydraulic locomotive

A GMD GMDH-1 diesel-hydraulic locomotive

Diesel-hydraulic locomotives have a smaller market share than those with diesel electric transmission - the main worldwide user of main-line hydraulic transmissions was the Federal Republic of Germany, with designs including the 1950s DB class V 200, and the 1960/70's DB Class V 160 family. British Rail introduced a number of diesel hydraulic designs during it 1955 Modernisation Plan, initially license built versions of German designs (see Category:Diesel-hydraulic locomotives of Great Britain). In Spain RENFE used high power to weight ratio twin engined German designs to haul high speed trains from the 1960s to 1990s. (see RENFE Classes 340, 350, 352, 353, 354)

Other main-line locomotives of the post war period included the 1950s GMD GMDH-1 experimental locomotives; the Henschel & Son built South African Class 61-000; in the 1960s Southern Pacific bought 18 Krauss-Maffei KM ML-4000 diesel-hydraulic locomotives. The Denver & Rio Grande Western also bought three, all of which were later sold to SP.

In Finland, over 200 Finnish-built VR class Dv12 and Dr14 diesel-hydraulics with Voith transmissions have been continuously used since the early 1960s. All units of Dr14 class and most units of Dv12 class are still in service. VR has abandoned some weak-conditioned units of 2700 series Dv12s.

In the 21st century series production standard gauge diesel-hydraulic designs include the Voith Gravita, ordered by Deutsche Bahn, and the Vossloh G2000, G1206 and G1700 designs, all manufactured in Germany for freight use.

Hydrostatic transmission

Hydraulic drive systems using a hydrostatic hydraulic drive system have been applied to rail use. Modern examples included 350 to 750 hp (260 to 560 kW) shunting locomotives by CMI Group (Belgium), 4 to 12 tonne 35 to 58 kW (47 to 78 hp) narrow gauge industrial locomoitves by Atlas Copco subsidiary GIA. Hydrostatic drives are also utilised in railway maintenance machines (tampers, rail grinders).

Application of hydrostatic transmissions are generally limited to small shunting locomotives and rail maintenance equipment, as well as being used for non-tractive applications in diesel engines such as drives for traction motor fans.

Diesel-steam

Main article: Steam diesel hybrid locomotive

Steam-diesel hybrid locomotives can use steam generated from a boiler or diesel to power a piston engine. The Cristiani Compressed Steam System used a diesel engine to power a compressor to drive and recirculate steam produced by a boiler; effectively using steam as the power transmission medium, with the diesel engine being the prime mover

Diesel-pneumatic

The diesel-pneumatic locomotive was of interest in the 1930s because it offered the possibility of converting existing steam locomotives to diesel operation. The frame and cylinders of the steam locomotive would be retained and the boiler would be replaced by a diesel engine driving an air compressor. The problem was low thermal efficiency because of the large amount of energy wasted as heat in the air compressor. Attempts were made to compensate for this by using the diesel exhaust to re-heat the compressed air but these had limited success. A German proposal of 1929 did result in a prototype but a similar British proposal of 1932, to use an LNER Class R1 locomotive, never got beyond the design stage.

Multiple-unit operation

Diesel-electric locomotive built by EMD for service in the UK and continental Europe.

Most Diesel locomotives are capable of multiple unit operation (MU) as a means of increasing horsepower and tractive effort when hauling heavy trains. All North American locomotives, including export models, use a standardized AAR electrical control system interconnected by a 27-pin jumper cable between the units. For UK-built locomotives, a number of incompatible control systems are used, but the most common is the Blue Star system, which is electro-pneumatic and fitted to most early diesel classes. A small number of types, typically higher-powered locomotives intended for passenger only work, do not have multiple control systems. In all cases, the electrical control connections made common to all units in a consist are referred to as trainlines. The result is that all locomotives in a consist behave as one in response to the engine driver's control movements.

The ability to couple Diesel-electric locomotives in an MU fashion was first introduced in the EMD FT four-unit demonstrator that toured the USA in 1939. At the time, American railroad work rules required that each operating locomotive in a train had to have on board a full crew. EMD circumvented that requirement by coupling the individual units of the demonstrator with drawbars instead of conventional knuckle couplers and declaring the combination to be a single locomotive. Electrical interconnections were made so one engine driver could operate the entire consist from the head-end unit. Later on, work rules were amended and the semi-permanent coupling of units with drawbars was eliminated in favour of couplers, as servicing had proved to be somewhat cumbersome owing to the total length of the consist (about 200 feet or nearly 61 meters).

In mountainous regions, it is common to interpose helper locomotives in the middle of the train, both to provide the extra power needed to ascend a grade and to limit the amount of stress applied to the draft gear of the car coupled to the head-end power. The helper units in such distributed power configurations are controlled from the lead unit's cab through coded radio signals. Although this is technically not an MU configuration, the behaviour is the same as with physically interconnected units.

Cab arrangements

Cab arrangements vary by builder and operator. Practice in the U.S. has traditionally been for a cab at one end of the locomotive with limited visibility if the locomotive is not operated cab forward. This is not usually a problem as U.S. locomotives are usually operated in pairs, or threes, and arranged so that a cab is at each end of each set. European practice is usually for a cab at each end of the locomotive as trains are usually light enough to operate with one locomotive. Early U.S. practice was to add power units without cabs (booster or B units) and the arrangement was often A-B, A-A, A-B-A, A-B-B, or A-B-B-A where A was a unit with a cab. Center cabs were sometimes used for switch locomotives.

Cow-calf

Main article: Cow-calf

In North American railroading, a cow-calf set is a pair of switcher-type locomotives: one (the cow) equipped with a driving cab, the other (the calf) without a cab, and controlled from the cow through cables. Cow-calf sets are used in heavy switching and hump yard service. Some are radio controlled without an operating engineer present in the cab. This arrangement is also known as master-slave. Where two connected units were present, EMD called these TR-2s (approximately 2,000 HP); where three units, TR-3s (approximately 3,000 HP).

Cow-calves have largely disappeared as these engine combinations exceeded their economic lifetimes many years ago.

Present North American practice is to pair two 3,000 HP GP40-2 or SD40-2 road switchers, often nearly worn-out and very soon ready for rebuilding or scrapping, and to utilize these for so-called "transfer" uses, for which the TR-2, TR-3 and TR-4 engines were originally intended, hence the designation TR, for "transfer".

Occasionally, the second unit may have its prime-mover and traction alternator removed and replaced by concrete and/or steel ballast and the power for traction obtained from the master unit. As a 16-cylinder prime-mover generally weighs in the 36,000 pound range, and a 3,000 HP traction alternator generally weighs in the 18,000 pound range, this would mean that 54,000 pounds would be needed for ballast.

A pair of fully capable "Dash 2" units would be rated 6,000 HP. A "Dash 2" pair where only one had a prime-mover/alternator would be rated 3,000 HP, with all power provided by master, but the combination benefits from the tractive effort provided by the slave as engines in transfer service are seldom called upon to provide 3,000 HP much less 6,000 HP on a continuous basis.

Flameproof diesel locomotive

A standard diesel locomotive presents a very low fire risk but “flame proofing” can reduce the risk even further. This involves fitting a water-filled box to the exhaust pipe to quench any red-hot carbon particles that may be emitted. Other precautions may include a fully insulated electrical system (neither side earthed to the frame) and all electric wiring enclosed in conduit.

The flameproof diesel locomotive has replaced the fireless steam locomotive in areas of high fire risk such as oil refineries and ammunition dumps. Preserved examples of flameproof diesel locomotives include:

• Francis Baily of Thatcham (ex-RAF Welford) at Southall Railway Centre
• Naworth (ex-National Coal Board) at the South Tynedale Railway

Latest development of the "Flameproof Diesel Vehicle Applied New Exhaust Gas Dry Type Treatment System” does not need the water supply.

Lights

A Canadian National Railway train showing the placement of the headlight and ditch lights on the locomotive.

The lights fitted to diesel locomotives vary from country to country. North American locomotives are fitted with two headlights for redundancy and a pair of ditch lights. The latter are fitted low down at the front and are designed to make the locomotive easily visible as it approaches a grade crossing. Older locomotives may be fitted with a Gyralite or Mars Light instead of the ditch lights.

Environmental impact

See also: Diesel exhaust

Although diesel locomotives generally emit less sulphur dioxide, a major pollutant to the environment, and greenhouse gases than steam locomotives, they are not completely clean in that respect. Furthermore, like other diesel powered vehicles, they emit nitrogen oxides and fine particles, which are a risk to public health. In fact, in this last respect diesel locomotives may perform worse than steam locomotives.

For years, it was thought by American government scientists who measure air pollution that diesel locomotive engines were relatively clean and emitted far less health-threatening emissions than those of diesel trucks or other vehicles; however, the scientists discovered that because they used faulty estimates of the amount of fuel consumed by diesel locomotives, they grossly understated the amount of pollution generated annually (In Europe, where most major railways have been electrified, there is less concern). After revising their calculations, they concluded that the annual emissions of nitrogen oxide, a major ingredient in smog and acid rain, and soot would be by 2030 nearly twice what they originally assumed.

This would mean that diesel locomotives would be releasing more than 800,000 tons of nitrogen oxide and 25,000 tons of soot every year within a quarter of a century, in contrast to the EPA's previous projections of 480,000 tons of nitrogen dioxide and 12,000 tons of soot. Since this was discovered, to reduce the effects of the diesel locomotive on humans (who are breathing the noxious emissions) and on plants and animals, it is considered practical to install traps in the diesel engines to reduce pollution levels and other forms (e.g., use of biodiesel).

Diesel locomotive pollution has been of particular concern in the city of Chicago. The Chicago Tribune reported levels of diesel soot inside locomotives leaving Chicago at levels hundreds of times above what is normally found on streets outside. Residents of several neighborhoods are most likely exposed to diesel emissions at levels several times higher than the national average for urban areas.

Mitigation

In 2008, the United States Environmental Protection Agency (EPA) mandated regulations requiring all new or refurbished diesel locomotives to meet Tier II pollution standards that slash the amount of allowable soot by 90% and require an 80% reduction in nitrogen oxide emissions. See List of low emissions locomotives.

Other technologies that are being deployed to reduce locomotive emissions and fuel consumption include "Genset" switching locomotives and hybrid Green Goat designs. Genset locomotives use multiple high-speed diesel engines and generators (generator sets), rather than a single medium-speed diesel engine and a single generator. Green Goats are a type of hybrid switching locomotive utilizing a small diesel engine and a large bank of rechargeable batteries. Switching locomotives are of particular concern as they typically operate in a limited area, often in or near urban centers, and spend much of their time idling. Both designs reduce pollution below EPA Tier II standards and cut or eliminate emissions during idle.

See also

• Diesel multiple unit
• Diesel-electric transmission
• Diesel engine
• Electric locomotive
• Electrification
• Electro-diesel locomotive
• Hybrid electric vehicle
• Hybrid locomotive
• Non-road engine

References

Sources

• Churella, Albert J. (1998). From Steam to Diesel: Managerial Customs and Organizational Capabilities in the Twentieth-Century American Locomotive Industry. Princeton, New Jersey: Princeton University Press. ISBN 0-691-02776-5. {{cite book}}: Invalid |ref=harv (help)
• Pinkepank, Jerry A. (1973). The Second Diesel Spotter’s Guide. Milwaukee WI: Kalmbach Books. ISBN 0-89024-026-4. {{cite book}}: Invalid |ref=harv (help)

External links

• US Government test of GP38-2 locomotive with biodiesel fuel.
• A 1926 article The Diesel Engine in Railway Transportation on Diesel locomotives
• Diesel locomotive