x86 instruction listings

The x86 instruction set refers to the set of instructions that x86-compatible microprocessors support. The instructions are usually part of an executable program, often stored as a computer file and executed on the processor.

The x86 instruction set has been extended several times, introducing wider registers and datatypes as well as new functionality.

x86 integer instructions

Main article: x86 assembly language

Below is the full 8086/8088 instruction set of Intel (81 instructions total). These instructions are also available in 32-bit mode, they operate instead on 32-bit registers (eax, ebx, etc.) and values instead of their 16-bit (ax, bx, etc.) counterparts. The updated instruction set is grouped according to architecture (i186, i286, i386, i486, i586/i686) and is referred to as (32-bit) x86 and (64-bit) x86-64 (also known as AMD64).

Original 8086/8088 instructions

This is the original instruction set. In the 'Notes' column, r means register, m means memory address and imm means immediate (i.e. a value).

Original 8086/8088 instruction set

In- struc- tion	Meaning	Notes	Opcode
AAA	ASCII adjust AL after addition	used with unpacked binary-coded decimal	0x37
AAD	ASCII adjust AX before division	8086/8088 datasheet documents only base 10 version of the AAD instruction (opcode 0xD5 0x0A), but any other base will work. Later Intel's documentation has the generic form too. NEC V20 and V30 (and possibly other NEC V-series CPUs) always use base 10, and ignore the argument, causing a number of incompatibilities	0xD5
AAM	ASCII adjust AX after multiplication	Only base 10 version (Operand is 0xA) is documented, see notes for AAD	0xD4
AAS	ASCII adjust AL after subtraction		0x3F
ADC	Add with carry	(1) r += (r/m/imm+CF); (2) m += (r/imm+CF);	0x10...0x15, 0x80...0x81/2, 0x83/2
ADD	Add	(1) r += r/m/imm; (2) m += r/imm;	0x00...0x05, 0x80/0...0x81/0, 0x83/0
AND	Logical AND	(1) r &= r/m/imm; (2) m &= r/imm;	0x20...0x25, 0x80...0x81/4, 0x83/4
CALL	Call procedure	push eip; eip points to the instruction directly after the call	0x9A, 0xE8, 0xFF/2, 0xFF/3
CBW	Convert byte to word	AX = AL ; sign extended	0x98
CLC	Clear carry flag	CF = 0;	0xF8
CLD	Clear direction flag	DF = 0;	0xFC
CLI	Clear interrupt flag	IF = 0;	0xFA
CMC	Complement carry flag	CF = !CF;	0xF5
CMP	Compare operands	(1) r - r/m/imm; (2) m - r/imm;	0x38...0x3D, 0x80...0x81/7, 0x83/7
CMPSB	Compare bytes in memory. May be used with a REPE or REPNE prefix to test and repeat the instruction CX times.	if (DF==0) *(byte*)SI++ - *(byte*)ES:DI++; else *(byte*)SI-- - *(byte*)ES:DI--;	0xA6
CMPSW	Compare words. May be used with a REPE or REPNE prefix to test and repeat the instruction CX times.	if (DF==0) *(word*)SI++ - *(word*)ES:DI++; else *(word*)SI-- - *(word*)ES:DI--;	0xA7
CWD	Convert word to doubleword		0x99
DAA	Decimal adjust AL after addition	(used with packed binary-coded decimal)	0x27
DAS	Decimal adjust AL after subtraction		0x2F
DEC	Decrement by 1		0x48...0x4F, 0xFE/1, 0xFF/1
DIV	Unsigned divide	(1) AX = DX:AX / r/m; resulting DX = remainder (2) AL = AX / r/m; resulting AH = remainder	0xF7/6, 0xF6/6
ESC	Used with floating-point unit		0xD8..0xDF
HLT	Enter halt state		0xF4
IDIV	Signed divide	(1) AX = DX:AX / r/m; resulting DX = remainder (2) AL = AX / r/m; resulting AH = remainder	0xF7/7, 0xF6/7
IMUL	Signed multiply in One-operand form	(1) DX:AX = AX * r/m; (2) AX = AL * r/m	0xF7/5, 0xF6/5
IN	Input from port	(1) AL = port[imm]; (2) AL = port[DX]; (3) AX = port[imm]; (4) AX = port[DX];	0xE4, 0xE5, 0xEC, 0xED
INC	Increment by 1		0x40...0x47, 0xFE/0, 0xFF/0
INT	Call to interrupt		0xCC, 0xCD
INTO	Call to interrupt if overflow		0xCE
IRET	Return from interrupt		0xCF
Jcc	Jump if condition	(JA, JAE, JB, JBE, JC, JE, JG, JGE, JL, JLE, JNA, JNAE, JNB, JNBE, JNC, JNE, JNG, JNGE, JNL, JNLE, JNO, JNP, JNS, JNZ, JO, JP, JPE, JPO, JS, JZ)	0x70...0x7F
JCXZ	Jump if CX is zero		0xE3
JMP	Jump		0xE9...0xEB, 0xFF/4, 0xFF/5
LAHF	Load FLAGS into AH register		0x9F
LDS	Load DS:r with far pointer		0xC5
LEA	Load Effective Address		0x8D
LES	Load ES:r with far pointer		0xC4
LOCK	Assert BUS LOCK# signal	(for multiprocessing)	0xF0
LODSB	Load string byte. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) AL = *SI++; else AL = *SI--;	0xAC
LODSW	Load string word. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) AX = *SI++; else AX = *SI--;	0xAD
LOOP/ LOOPx	Loop control	(LOOPE, LOOPNE, LOOPNZ, LOOPZ) if (x && --CX) goto lbl;	0xE0...0xE2
MOV	Move	(1) r = r/m/imm; (2) m = r/imm (3) r/m = sreg; (4) sreg = r/m;	0xA0...0xA3, 0x8C, 0x8E
MOVSB	Move byte from string to string. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) *(byte*)ES:DI++ = *(byte*)SI++; else *(byte*)ES:DI-- = *(byte*)SI--; .	0xA4
MOVSW	Move word from string to string. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) *(word*)ES:DI++ = *(word*)SI++; else *(word*)ES:DI-- = *(word*)SI--;	0xA5
MUL	Unsigned multiply	(1) DX:AX = AX * r/m; (2) AX = AL * r/m;	0xF7/4, 0xF6/4
NEG	Two's complement negation	r/m = 0 – r/m;	0xF6/3...0xF7/3
NOP	No operation	opcode equivalent to XCHG EAX, EAX	0x90
NOT	Negate the operand, logical NOT	r/m ^= -1;	0xF6/2...0xF7/2
OR	Logical OR	(1) r ∣= r/m/imm; (2) m ∣= r/imm;	0x08...0x0D, 0x80...0x81/1, 0x83/1
OUT	Output to port	(1) port[imm] = AL; (2) port[DX] = AL; (3) port[imm] = AX; (4) port[DX] = AX;	0xE6, 0xE7, 0xEE, 0xEF
POP	Pop data from stack	r/m/sreg = *SP++;	0x07, 0x17, 0x1F, 0x58...0x5F, 0x8F/0
POPF	Pop FLAGS register from stack	FLAGS = *SP++;	0x9D
PUSH	Push data onto stack	*--SP = r/m/sreg;	0x06, 0x0E, 0x16, 0x1E, 0x50...0x57, 0xFF/6
PUSHF	Push FLAGS onto stack	*--SP = FLAGS;	0x9C
RCL	Rotate left (with carry)		0xC0...0xC1/2 (186+), 0xD0...0xD3/2
RCR	Rotate right (with carry)		0xC0...0xC1/3 (186+), 0xD0...0xD3/3
REPxx	Repeat MOVS/STOS/CMPS/LODS/SCAS	(REP, REPE, REPNE, REPNZ, REPZ)	0xF2, 0xF3
RET	Return from procedure	Not a real instruction. The assembler will translate these to a RETN or a RETF depending on the memory model of the target system.
RETN	Return from near procedure		0xC2, 0xC3
RETF	Return from far procedure		0xCA, 0xCB
ROL	Rotate left		0xC0...0xC1/0 (186+), 0xD0...0xD3/0
ROR	Rotate right		0xC0...0xC1/1 (186+), 0xD0...0xD3/1
SAHF	Store AH into FLAGS		0x9E
SAL	Shift Arithmetically left (signed shift left)	(1) r/m <<= 1; (2) r/m <<= CL;	0xC0...0xC1/4 (186+), 0xD0...0xD3/4
SAR	Shift Arithmetically right (signed shift right)	(1) (signed) r/m >>= 1; (2) (signed) r/m >>= CL;	0xC0...0xC1/7 (186+), 0xD0...0xD3/7
SBB	Subtraction with borrow	(1) r -= (r/m/imm+CF); (2) m -= (r/imm+CF); alternative 1-byte encoding of SBB AL, AL is available via undocumented SALC instruction	0x18...0x1D, 0x80...0x81/3, 0x83/3
SCASB	Compare byte string. May be used with a REPE or REPNE prefix to test and repeat the instruction CX times.	if (DF==0) AL - *ES:DI++; else AL - *ES:DI--;	0xAE
SCASW	Compare word string. May be used with a REPE or REPNE prefix to test and repeat the instruction CX times.	if (DF==0) AX - *ES:DI++; else AX - *ES:DI--;	0xAF
SHL	Shift left (unsigned shift left)		0xC0...0xC1/4 (186+), 0xD0...0xD3/4
SHR	Shift right (unsigned shift right)		0xC0...0xC1/5 (186+), 0xD0...0xD3/5
STC	Set carry flag	CF = 1;	0xF9
STD	Set direction flag	DF = 1;	0xFD
STI	Set interrupt flag	IF = 1;	0xFB
STOSB	Store byte in string. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) *ES:DI++ = AL; else *ES:DI-- = AL;	0xAA
STOSW	Store word in string. May be used with a REP prefix to repeat the instruction CX times.	if (DF==0) *ES:DI++ = AX; else *ES:DI-- = AX;	0xAB
SUB	Subtraction	(1) r -= r/m/imm; (2) m -= r/imm;	0x28...0x2D, 0x80...0x81/5, 0x83/5
TEST	Logical compare (AND)	(1) r & r/m/imm; (2) m & r/imm;	0x84, 0x85, 0xA8, 0xA9, 0xF6/0, 0xF7/0
WAIT	Wait until not busy	Waits until BUSY# pin is inactive (used with floating-point unit)	0x9B
XCHG	Exchange data	r :=: r/m; A spinlock typically uses xchg as an atomic operation. (coma bug).	0x86, 0x87, 0x91...0x97
XLAT	Table look-up translation	behaves like MOV AL, [BX+AL]	0xD7
XOR	Exclusive OR	(1) r ^+= r/m/imm; (2) m ^= r/imm;	0x30...0x35, 0x80...0x81/6, 0x83/6

Added in specific processors

Added with 80186/80188

Instruction	Opcode	Meaning	Notes
BOUND	62 /r	Check array index against bounds	raises software interrupt 5 if test fails
ENTER	C8 iw ib	Enter stack frame	Modifies stack for entry to procedure for high level language. Takes two operands: the amount of storage to be allocated on the stack and the nesting level of the procedure.
INSB/INSW	6C	Input from port to string. May be used with a REP prefix to repeat the instruction CX times.	equivalent to: IN AL, DX MOV ES:[DI], AL INC DI ; adjust DI according to operand size and DF
	6D
LEAVE	C9	Leave stack frame	Releases the local stack storage created by the previous ENTER instruction.
OUTSB/OUTSW	6E	Output string to port. May be used with a REP prefix to repeat the instruction CX times.	equivalent to: MOV AL, DS:[SI] OUT DX, AL INC SI ; adjust SI according to operand size and DF
	6F
POPA	61	Pop all general purpose registers from stack	equivalent to: POP DI POP SI POP BP POP AX ; no POP SP here, all it does is ADD SP, 2 (since AX will be overwritten later) POP BX POP DX POP CX POP AX
PUSHA	60	Push all general purpose registers onto stack	equivalent to: PUSH AX PUSH CX PUSH DX PUSH BX PUSH SP ; The value stored is the initial SP value PUSH BP PUSH SI PUSH DI
PUSH immediate	6A ib	Push an immediate byte/word value onto the stack	example: PUSH 12h PUSH 1200h
	68 iw
IMUL immediate	6B /r ib	Signed and unsigned multiplication of immediate byte/word value	example: IMUL BX,12h IMUL DX,1200h IMUL CX, DX, 12h IMUL BX, SI, 1200h IMUL DI, word ptr [BX+SI], 12h IMUL SI, word ptr [BP-4], 1200h Note that since the lower half is the same for unsigned and signed multiplication, this version of the instruction can be used for unsigned multiplication as well.
	69 /r iw
SHL/SHR/SAL/SAR/ROL/ROR/RCL/RCR immediate	C0	Rotate/shift bits with an immediate value greater than 1	example: ROL AX,3 SHR BL,3
	C1

Added with 80286

The new instructions added in 80286 add support for x86 protected mode. Some but not all of the instructions are available in real mode as well.

Instruction	Opcode	Instruction description	Real mode	Ring
LGDT m16&32	0F 01 /2	Load GDTR (Global Descriptor Table Register) from memory.	Yes	0
LIDT m16&32	0F 01 /3	Load IDTR (Interrupt Descriptor Table Register) from memory. The IDTR controls not just the address/size of the IDT (interrupt Descriptor Table) in protected mode, but the IVT (Interrupt Vector Table) in real mode as well.
LMSW r/m16	0F 01 /6	Load MSW (Machine Status Word) from 16-bit register or memory.
CLTS	0F 06	Clear task-switched flag in the MSW.
LLDT r/m16	0F 00 /2	Load LDTR (Local Descriptor Table Register) from 16-bit register or memory.	#UD
LTR r/m16	0F 00 /3	Load TR (Task Register) from 16-bit register or memory. The TSS (Task State Segment) specified by the 16-bit argument is marked busy, but a task switch is not done.
SGDT m16&32	0F 01 /0	Store GDTR to memory.	Yes	Usually 3
SIDT m16&32	0F 01 /1	Store IDTR to memory.
SMSW r/m16	0F 01 /4	Store MSW to register or 16-bit memory.
SLDT r/m16	0F 00 /0	Store LDTR to register or 16-bit memory.	#UD
STR r/m16	0F 00 /1	Store TR to register or 16-bit memory.
ARPL r/m16,r16	63 /r	Adjust RPL (Requested Privilege Level) field of selector. The operation performed is: if (dst & 3) < (src & 3) then dst = (dst & 0xFFFC) | (src & 3) eflags.zf = 1 else eflags.zf = 0	#UD	3
LAR r,r/m16	0F 02 /r	Load access rights byte from the specified segment descriptor. Reads bytes 4-7 of segment descriptor, bitwise-ANDs it with 0x00FxFF00, then stores the bottom 16/32 bits of the result in destination register. Sets EFLAGS.ZF=1 if the descriptor could be loaded, ZF=0 otherwise.	#UD
LSL r,r/m16	0F 03 /r	Load segment limit from the specified segment descriptor. Sets ZF=1 if the descriptor could be loaded, ZF=0 otherwise.
VERR r/m16	0F 00 /4	Verify a segment for reading. Sets ZF=1 if segment can be read, ZF=0 otherwise.
VERW r/m16	0F 00 /5	Verify a segment for writing. Sets ZF=1 if segment can be written, ZF=0 otherwise.
LOADALL	0F 05	Load all CPU registers from a 102-byte data structure starting at physical address 800h, including "hidden" part of segment descriptor registers.	Yes	0
STOREALL	F1 0F 04	Store all CPU registers to a 102-byte data structure starting at physical address 800h, then shut down CPU.

Added with 80386

The 80386 added support for 32-bit operation to the x86 instruction set. This was done by widening the general-purpose registers to 32 bits and introducing the concepts of OperandSize and AddressSize – most instruction forms that would previously take 16-bit data arguments were given the ability to take 32-bit arguments by setting their OperandSize to 32 bits, and instructions that could take 16-bit address arguments were given the ability to take 32-bit address arguments by setting their AddressSize to 32 bits. (Instruction forms that work on 8-bit data continue to be 8-bit regardless of OperandSize. Using a data size of 16 bits will cause only the bottom 16 bits of the 32-bit general-purpose registers to be modified – the top 16 bits are left unchanged.)

The default OperandSize and AddressSize to use for each instruction is given by the D bit of the segment descriptor of the current code segment - D=0 makes both 16-bit, D=1 makes both 32-bit. Additionally, they can be overridden on a per-instruction basis with two new instruction prefixes that were introduced in the 80386:

• 66h: OperandSize override. Will change OperandSize from 16-bit to 32-bit if CS.D=0, or from 32-bit to 16-bit if CS.D=1.
• 67h: AddressSize override. Will change AddressSize from 16-bit to 32-bit if CS.D=0, or from 32-bit to 16-bit if CS.D=1.

The 80386 also introduced the two new segment registers FS and GS as well as the x86 control, debug and test registers.

The new instructions introduced in the 80386 can broadly be subdivided into two classes:

• Pre-existing opcodes that needed new mnemonics for their 32-bit OperandSize variants (e.g. CWDE, LODSD)
• New opcodes that introduced new functionality (e.g. SHLD, SETcc)

For instruction forms where the operand size can be inferred from the instruction's arguments (e.g. ADD EAX,EBX can be inferred to have a 32-bit OperandSize due to its use of EAX as an argument), new instruction mnemonics are not needed and not provided.

80386: new instruction mnemonics for 32-bit variants of older opcodes

Type	Instruction mnemonic	Opcode	Description	Mnemonic for older 16-bit variant	Ring
String instructions	LODSD	AD	Load string doubleword: EAX := DS:[rSI±±]	LODSW	3
	STOSD	AB	Store string doubleword: ES:[rDI±±] := EAX	STOSW
	MOVSD	A5	Move string doubleword: ES:[rDI±±] := DS:[rSI±±]	MOVSW
	CMPSD	A7	Compare string doubleword: temp1 := DS:[rSI±±] temp2 := ES:[rDI±±] CMP temp1, temp2 /* 32-bit compare and set EFLAGS */	CMPSW
	SCASD	AF	Scan string doubleword: temp1 := ES:[rDI±±] CMP EAX, temp1 /* 32-bit compare and set EFLAGS */	SCASW
	INSD	6D	Input string from doubleword I/O port:ES:[rDI±±] := port[DX]	INSW	Usually 0
	OUTSD	6F	Output string to doubleword I/O port:port[DX] := DS:[rSI±±]	OUTSW
Other	CWDE	98	Sign-extend 16-bit value in AX to 32-bit value in EAX	CBW	3
	CDQ	99	Sign-extend 32-bit value in EAX to 64-bit value in EDX:EAX. Mainly used to prepare a dividend for the 32-bit IDIV (signed divide) instruction.	CWD
	JECXZ rel8	E3 cb	Jump if ECX is zero	JCXZ
	PUSHAD	60	Push all 32-bit registers onto stack	PUSHA
	POPAD	61	Pop all 32-bit general-purpose registers off stack	POPA
	PUSHFD	9C	Push 32-bit EFLAGS register onto stack	PUSHF	Usually 3
	POPFD	9D	Pop 32-bit EFLAGS register off stack	POPF
	IRETD	CF	32-bit interrupt return. Differs from the older 16-bit IRET instruction in that it will pop interrupt return items (EIP,CS,EFLAGS; also ESP and SS if there is a CPL change; and also ES,DS,FS,GS if returning to virtual 8086 mode) off the stack as 32-bit items instead of 16-bit items. Should be used to return from interrupts when the interrupt handler was entered through a 32-bit IDT interrupt/trap gate. Instruction is serializing.	IRET

80386: new opcodes introduced

Instruction mnemonics	Opcode	Description	Ring
BT r/m, r	0F A3 /r	Bit Test. Second operand specifies which bit of the first operand to test. The bit to test is copied to EFLAGS.CF.	3
BT r/m, imm8	0F BA /4 ib
BTS r/m, r	0F AB /r	Bit Test-and-set. Second operand specifies which bit of the first operand to test and set.
BTS r/m, imm8	0F BA /5 ib
BTR r/m, r	0F B3 /r	Bit Test and Reset. Second operand specifies which bit of the first operand to test and clear.
BTR r/m, imm8	0F BA /6 ib
BTC r/m, r	0F BB /r	Bit Test and Complement. Second operand specifies which bit of the first operand to test and toggle.
BTC r/m, imm8	0F BA /7 ib
BSF r, r/m	NFx 0F BC /r	Bit scan forward. Returns bit index of lowest set bit in input.	3
BSR r, r/m	NFx 0F BD /r	Bit scan reverse. Returns bit index of highest set bit in input.
SHLD r/m, r, imm8	0F A4 /r ib	Shift Left Double. The operation of SHLD arg1,arg2,shamt is: arg1 := (arg1<<shamt) | (arg2>>(operand_size - shamt))
SHLD r/m, r, CL	0F A5 /r
SHRD r/m, r, imm8	0F AC /r ib	Shift Right Double. The operation of SHRD arg1,arg2,shamt is: arg1 := (arg1>>shamt) | (arg2<<(operand_size - shamt))
SHRD r/m, r, CL	0F AD /r
MOVZX reg, r/m8	0F B6 /r	Move from 8/16-bit source to 16/32-bit register with zero-extension.	3
MOVZX reg, r/m16	0F B7 /r
MOVSX reg, r/m8	0F BE /r	Move from 8/16-bit source to 16/32/64-bit register with sign-extension.
MOVSX reg, r/m16	0F BF /r
SETcc r/m8	0F 9x /0	Set byte to 1 if condition is satisfied, 0 otherwise.
Jcc rel16 Jcc rel32	0F 8x cw 0F 8x cd	Conditional jump near. Differs from older variants of conditional jumps in that they accept a 16/32-bit offset rather than just an 8-bit offset.
IMUL r, r/m	0F AF /r	Two-operand non-widening integer multiply.
FS:	64	Segment-override prefixes for FS and GS segment registers.	3
GS:	65
PUSH FS	0F A0	Push/pop FS and GS segment registers.
POP FS	0F A1
PUSH GS	0F A8
POP GS	0F A9
LFS r16, m16&16 LFS r32, m32&16	0F B4 /r	Load far pointer from memory. Offset part is stored in destination register argument, segment part in FS/GS/SS segment register as indicated by the instruction mnemonic.
LGS r16, m16&16 LGS r32, m32&16	0F B5 /r
LSS r16, m16&16 LSS r32, m32&16	0F B2 /r
MOV reg,CRx	0F 20 /r	Move from control register to general register.	0
MOV CRx,reg	0F 22 /r	Move from general register to control register. Moves to the CR3 control register are serializing and will flush the TLB. On Pentium and later processors, moves to the CR0 and CR4 control registers are also serializing.
MOV reg,DRx	0F 21 /r	Move from x86 debug register to general register.
MOV DRx,reg	0F 23 /r	Move from general register to x86 debug register. On Pentium and later processors, moves to the DR0-DR7 debug registers are serializing.
MOV reg,TRx	0F 24 /r	Move from x86 test register to general register.
MOV TRx,reg	0F 26 /r	Move from general register to x86 test register.
ICEBP,  INT01,  INT1	F1	In-circuit emulation breakpoint. Performs software interrupt #1 if executed when not using in-circuit emulation.	3
UMOV r/m, r8	0F 10 /r	User Move – perform data moves that can access user memory while in In-circuit emulation HALT mode. Performs same operation as MOV if executed when not doing in-circuit emulation.
UMOV r/m, r16/32	0F 11 /r
UMOV r8, r/m	0F 12 /r
UMOV r16/32, r/m	0F 13 /r
XBTS reg,r/m	0F A6 /r	Bitfield extract (early 386 only).
IBTS r/m,reg	0F A7 /r	Bitfield insert (early 386 only).
LOADALLD,  LOADALL386	0F 07	Load all CPU registers from a 296-byte data structure starting at ES:EDI, including "hidden" part of segment descriptor registers.	0

Added with 80486

Instruction	Opcode	Description	Ring
BSWAP r32	0F C8+r	Byte Order Swap. Usually used to convert between big-endian and little-endian data representations. For 32-bit registers, the operation performed is: r = (r << 24) | ((r << 8) & 0x00FF0000) | ((r >> 8) & 0x0000FF00) | (r >> 24); Using BSWAP with a 16-bit register argument produces an undefined result.	3
CMPXCHG r/m8,r8	0F B0 /r	Compare and Exchange. If accumulator (AL/AX/EAX/RAX) compares equal to first operand, then EFLAGS.ZF is set to 1 and the first operand is overwritten with the second operand. Otherwise, EFLAGS.ZF is set to 0, and first operand is copied into the accumulator. Instruction atomic only if used with LOCK prefix.
CMPXCHG r/m,r16 CMPXCHG r/m,r32	0F B1 /r
XADD r/m,r8	0F C0 /r	eXchange and ADD. Exchanges the first operand with the second operand, then stores the sum of the two values into the destination operand. Instruction atomic only if used with LOCK prefix.
XADD r/m,r16 XADD r/m,r32	0F C1 /r
INVLPG m8	0F 01 /7	Invalidate the TLB entries that would be used for the 1-byte memory operand. Instruction is serializing.	0
INVD	0F 08	Invalidate Internal Caches. Modified data in the cache are not written back to memory, potentially causing data loss.
WBINVD	NFx 0F 09	Write Back and Invalidate Cache. Writes back all modified cache lines in the processor's internal cache to main memory and invalidates the internal caches.

Added in P5/P6-class processors

Integer/system instructions that were not present in the basic 80486 instruction set, but were added in various x86 processors prior to the introduction of SSE. (Discontinued instructions are not included.)

Instruction	Opcode	Description	Ring	Added in
RDMSR	0F 32	Read Model-specific register. The MSR to read is specified in ECX. The value of the MSR is then returned as a 64-bit value in EDX:EAX.	0	IBM 386SLC, Intel Pentium, AMD K5, Cyrix 6x86MX,MediaGXm, IDT WinChip C6, Transmeta Crusoe, DM&P Vortex86DX3
WRMSR	0F 30	Write Model-specific register. The MSR to write is specified in ECX, and the data to write is given in EDX:EAX. Instruction is, with some exceptions, serializing.
RSM	0F AA	Resume from System Management Mode. Instruction is serializing.	-2 (SMM)	Intel 386SL, 486SL, Intel Pentium, AMD 5x86, Cyrix 486SLC/e, IDT WinChip C6, Transmeta Crusoe, Rise mP6
CPUID	0F A2	CPU Identification and feature information. Takes as input a CPUID leaf index in EAX and, depending on leaf, a sub-index in ECX. Result is returned in EAX,EBX,ECX,EDX. Instruction is serializing, and causes a mandatory #VMEXIT under virtualization. Support for CPUID can be checked by toggling bit 21 of EFLAGS (EFLAGS.ID) – if this bit can be toggled, CPUID is present.	Usually 3	Intel Pentium, AMD 5x86, Cyrix 5x86, IDT WinChip C6, Transmeta Crusoe, Rise mP6, NexGen Nx586, UMC Green CPU
CMPXCHG8B m64	0F C7 /1	Compare and Exchange 8 bytes. Compares EDX:EAX with m64. If equal, set ZF and store ECX:EBX into m64. Else, clear ZF and load m64 into EDX:EAX. Instruction atomic only if used with LOCK prefix.	3	Intel Pentium, AMD K5, Cyrix 6x86L,MediaGXm, IDT WinChip C6, Transmeta Crusoe, Rise mP6
RDTSC	0F 31	Read 64-bit Time Stamp Counter (TSC) into EDX:EAX. In early processors, the TSC was a cycle counter, incrementing by 1 for each clock cycle (which could cause its rate to vary on processors that could change clock speed at runtime) – in later processors, it increments at a fixed rate that doesn't necessarily match the CPU clock speed.	Usually 3	Intel Pentium, AMD K5, Cyrix 6x86MX,MediaGXm, IDT WinChip C6, Transmeta Crusoe, Rise mP6
RDPMC	0F 33	Read Performance Monitoring Counter. The counter to read is specified by ECX and its value is returned in EDX:EAX.	Usually 3	Intel Pentium MMX, Intel Pentium Pro, AMD K7, Cyrix 6x86MX, IDT WinChip C6, AMD Geode LX, VIA Nano
CMOVcc reg,r/m	0F 4x /r	Conditional move to register. The source operand may be either register or memory.	3	Intel Pentium Pro, AMD K7, Cyrix 6x86MX,MediaGXm, Transmeta Crusoe, VIA C3 "Nehemiah", DM&P Vortex86DX3
NOP r/m, NOPL r/m	NFx 0F 1F /0	Official long NOP. Other than AMD K7/K8, broadly unsupported in non-Intel processors released before 2005.	3	Intel Pentium Pro, AMD K7, x86-64, VIA C7
UD2, UD2A	0F 0B	Undefined Instructions – will generate an invalid opcode (#UD) exception in all operating modes. These instructions are provided for software testing to explicitly generate invalid opcodes. The opcodes for these instructions are reserved for this purpose.	(3)	(80186), Intel Pentium
UD1 reg,r/m, UD2B reg,r/m	0F B9 /r
OIO, UD0, UD0 reg,r/m	0F FF, 0F FF /r			(80186), Cyrix 6x86, AMD K5
SYSCALL	0F 05	Fast System call.	3	AMD K6, x86-64
SYSRET	0F 07	Fast Return from System Call. Designed to be used together with SYSCALL.	0
SYSENTER	0F 34	Fast System call.	3	Intel Pentium II, AMD K7, Transmeta Crusoe, NatSemi Geode GX2, VIA C3 "Nehemiah", DM&P Vortex86DX3
SYSEXIT	0F 35	Fast Return from System Call. Designed to be used together with SYSENTER.	0

Added as instruction set extensions

Added with x86-64

These instructions can only be encoded in 64 bit mode. They fall in four groups:

• original instructions that reuse existing opcodes for a different purpose (MOVSXD replacing ARPL)
• original instructions with new opcodes (SWAPGS)
• existing instructions extended to a 64 bit address size (JRCXZ)
• existing instructions extended to a 64 bit operand size (remaining instructions)

Most instructions with a 64 bit operand size encode this using a REX.W prefix; in the absence of the REX.W prefix, the corresponding instruction with 32 bit operand size is encoded. This mechanism also applies to most other instructions with 32 bit operand size. These are not listed here as they do not gain a new mnemonic in Intel syntax when used with a 64 bit operand size.

Instruction	Encoding	Meaning	Ring
CDQE	REX.W 98	Sign extend EAX into RAX	3
CQO	REX.W 99	Sign extend RAX into RDX:RAX
CMPSQ	REX.W A7	CoMPare String Quadword
CMPXCHG16B m128	REX.W 0F C7 /1	CoMPare and eXCHanGe 16 Bytes. Atomic only if used with LOCK prefix.
IRETQ	REX.W CF	64-bit Return from Interrupt
JRCXZ rel8	E3 cb	Jump if RCX is zero
LODSQ	REX.W AD	LoaD String Quadword
MOVSXD r64,r/m32	REX.W 63 /r	MOV with Sign Extend 32-bit to 64-bit
MOVSQ	REX.W A5	Move String Quadword
POPFQ	9D	POP RFLAGS Register
PUSHFQ	9C	PUSH RFLAGS Register
SCASQ	REX.W AF	SCAn String Quadword
STOSQ	REX.W AB	STOre String Quadword
SWAPGS	0F 01 F8	Exchange GS base with KernelGSBase MSR	0

Bit manipulation extensions

Main article: X86 Bit manipulation instruction set

Bit manipulation instructions. For all of the VEX-encoded instructions defined by BMI1 and BMI2, the operand size may be 32 or 64 bits, controlled by the VEX.W bit – none of these instructions are available in 16-bit variants.

Bit Manipulation Extension	Instruction mnemonics	Opcode	Instruction description	Added in
ABM (LZCNT) Advanced Bit Manipulation	POPCNT r16,r/m16 POPCNT r32,r/m32	F3 0F B8 /r	Population Count. Counts the number of bits that are set to 1 in its source argument.	K10, Bobcat, Haswell, ZhangJiang, Gracemont
	POPCNT r64,r/m64	F3 REX.W 0F B8 /r
	LZCNT r16,r/m16 LZCNT r32,r/m32	F3 0F BD /r	Count Leading zeroes. If source operand is all-0s, then LZCNT will return operand size in bits (16/32/64) and set CF=1.
	LZCNT r64,r/m64	F3 REX.W 0F BD /r
BMI1 Bit Manipulation Instruction Set 1	TZCNT r16,r/m16 TZCNT r32,r/m32	F3 0F BC /r	Count Trailing zeroes. If source operand is all-0s, then TZCNT will return operand size in bits (16/32/64) and set CF=1.	Haswell, Piledriver, Jaguar, ZhangJiang, Gracemont
	TZCNT r64,r/m64	F3 REX.W 0F BC /r
	ANDN ra,rb,r/m	VEX.LZ.0F38 F2 /r	Bitwise AND-NOT: ra = r/m AND NOT(rb)
	BEXTR ra,r/m,rb	VEX.LZ.0F38 F7 /r	Bitfield extract. Bitfield start position is specified in bits [7:0] of rb, length in bits[15:8] of rb. The bitfield is then extracted from the r/m value with zero-extension, then stored in ra. Equivalent to mask = (1 << rb[15:8]) - 1 ra = (r/m >> rb[7:0]) AND mask
	BLSI reg,r/m	VEX.LZ.0F38 F3 /3	Extract lowest set bit in source argument. Returns 0 if source argument is 0. Equivalent to dst = (-src) AND src
	BLSMSK reg,r/m	VEX.LZ.0F38 F3 /2	Generate a bitmask of all-1s bits up to the lowest bit position with a 1 in the source argument. Returns all-1s if source argument is 0. Equivalent to dst = (src-1) XOR src
	BLSR reg,r/m	VEX.LZ.0F38 F3 /1	Copy all bits of the source argument, then clear the lowest set bit. Equivalent to dst = (src-1) AND src
BMI2 Bit Manipulation Instruction Set 2	BZHI ra,r/m,rb	VEX.LZ.0F38 F5 /r	Zero out high-order bits in r/m starting from the bit position specified in rb, then write result to rd. Equivalent to ra = r/m AND NOT(-1 << rb[7:0])	Haswell, Excavator, ZhangJiang, Gracemont
	MULX ra,rb,r/m	VEX.LZ.F2.0F38 F6 /r	Widening unsigned integer multiply without setting flags. Multiplies EDX/RDX with r/m, then stores the low half of the multiplication result in ra and the high half in rb. If ra and rb specify the same register, only the high half of the result is stored.
	PDEP ra,rb,r/m	VEX.LZ.F2.0F38 F5 /r	Parallel Bit Deposit. Scatters contiguous bits from rb to the bit positions set in r/m, then stores result to ra. Operation performed is: ra=0; k=0; mask=r/m for i=0 to opsize-1 do if (mask[i] == 1) then ra[i]=rb[k]; k=k+1
	PEXT ra,rb,r/m	VEX.LZ.F3.0F38 F5 /r	Parallel Bit Extract. Uses r/m argument as a bit mask to select bits in rb, then compacts the selected bits into a contiguous bit-vector. Operation performed is: ra=0; k=0; mask=r/m for i=0 to opsize-1 do if (mask[i] == 1) then ra[k]=rb[i]; k=k+1
	RORX reg,r/m,imm8	VEX.LZ.F2.0F3A F0 /r ib	Rotate right by immediate without affecting flags.
	SARX ra,r/m,rb	VEX.LZ.F3.0F38 F7 /r	Arithmetic shift right without updating flags. For SARX, SHRX and SHLX, the shift-amount specified in rb is masked to 5 bits for 32-bit operand size and 6 bits for 64-bit operand size.
	SHRX ra,r/m,rb	VEX.LZ.F2.0F38 F7 /r	Logical shift right without updating flags.
	SHLX ra,r/m,rb	VEX.LZ.66.0F38 F7 /r	Shift left without updating flags.

Added with Intel TSX

Main article: Transactional Synchronization Extensions

TSX Subset	Instruction	Opcode	Description	Added in
RTM Restricted Transactional memory	XBEGIN rel16 XBEGIN rel32	C7 F8 cw C7 F8 cd	Start transaction. If transaction fails, perform a branch to the given relative offset.	Haswell (Deprecated on desktop/laptop CPUs from 10th generation (Ice Lake, Comet Lake) onwards, but continues to be available on Xeon-branded server parts (e.g. Ice Lake-SP, Sapphire Rapids))
	XABORT imm8	C6 F8 ib	Abort transaction with 8-bit immediate as error code.
	XEND	NP 0F 01 D5	End transaction.
	XTEST	NP 0F 01 D6	Test if in transactional execution. Sets EFLAGS.ZF to 0 if executed inside a transaction (RTM or HLE), 1 otherwise.
HLE Hardware Lock Elision	XACQUIRE	F2	Instruction prefix to indicate start of hardware lock elision, used with memory atomic instructions only (for other instructions, the F2 prefix may have other meanings). When used with such instructions, may start a transaction instead of performing the memory atomic operation.	Haswell (Discontinued – the last processors to support HLE were Coffee Lake and Cascade Lake)
	XRELEASE	F3	Instruction prefix to indicate end of hardware lock elision, used with memory atomic/store instructions only (for other instructions, the F3 prefix may have other meanings). When used with such instructions during hardware lock elision, will end the associated transaction instead of performing the store/atomic.
TSXLDTRK Load Address Tracking suspend/resume	XSUSLDTRK	F2 0F 01 E8	Suspend Tracking Load Addresses	Sapphire Rapids
	XRESLDTRK	F2 0F 01 E9	Resume Tracking Load Addresses

Added with Intel CET

Intel CET (Control-Flow Enforcement Technology) adds two distinct features to help protect against security exploits such as return-oriented programming: a shadow stack (CET_SS), and indirect branch tracking (CET_IBT).

CET Subset	Instruction	Opcode	Description	Ring	Added in
CET_SS Shadow stack. When shadow stacks are enabled, return addresses are pushed on both the regular stack and the shadow stack when a function call is made. They are then both popped on return from the function call – if they do not match, then the stack is assumed to be corrupted, and a #CP exception is issued. The shadow stack is additionally required to be stored in specially marked memory pages which cannot be modified by normal memory store instructions.	INCSSPD r32	F3 0F AE /5	Increment shadow stack pointer	3	Tiger Lake, Zen 3
	INCSSPQ r64	F3 REX.W 0F AE /5
	RDSSPD r32	F3 0F 1E /1	Read shadow stack pointer into register (low 32 bits)
	RDSSPQ r64	F3 REX.W 0F 1E /1	Read shadow stack pointer into register (full 64 bits)
	SAVEPREVSSP	F3 0F 01 EA	Save previous shadow stack pointer
	RSTORSSP m64	F3 0F 01 /5	Restore saved shadow stack pointer
	WRSSD m32,r32	NP 0F 38 F6 /r	Write 4 bytes to shadow stack
	WRSSQ m64,r64	NP REX.W 0F 38 F6 /r	Write 8 bytes to shadow stack
	WRUSSD m32,r32	66 0F 38 F5 /r	Write 4 bytes to user shadow stack	0
	WRUSSQ m64,r64	66 REX.W 0F 38 F5 /r	Write 8 bytes to user shadow stack
	SETSSBSY	F3 0F 01 E8	Mark shadow stack busy
	CLRSSBSY m64	F3 0F AE /6	Clear shadow stack busy flag
CET_IBT Indirect Branch Tracking. When IBT is enabled, an indirect branch (jump, call, return) to any instruction that is not an ENDBR32/64 instruction will cause a #CP exception.	ENDBR32	F3 0F 1E FB	Terminate indirect branch in 32-bit mode	3	Tiger Lake
	ENDBR64	F3 0F 1E FA	Terminate indirect branch in 64-bit mode
	NOTRACK	3E	Prefix used with indirect CALL/JMP near instructions (opcodes FF /2 and FF /4) to indicate that the branch target is not required to start with an ENDBR32/64 instruction. Prefix only honored when NO_TRACK_EN flag is set.

Added with XSAVE

The XSAVE instruction set extensions are designed to save/restore CPU extended state (typically for the purpose of context switching) in a manner that can be extended to cover new instruction set extensions without the OS context-switching code needing to understand the specifics of the new extensions. This is done by defining a series of state-components, each with a size and offset within a given save area, and each corresponding to a subset of the state needed for one CPU extension or another. The EAX=0Dh CPUID leaf is used to provide information about which state-components the CPU supports and what their sizes/offsets are, so that the OS can reserve the proper amount of space and set the associated enable-bits.

XSAVE Extension	Instruction mnemonics	Opcode	Instruction description	Ring	Added in
XSAVE Processor Extended State Save/Restore.	XSAVE mem XSAVE64 mem	NP 0F AE /4 NP REX.W 0F AE /4	Save state components specified by bitmap in EDX:EAX to memory.	3	Penryn, Bulldozer, Jaguar, Goldmont, ZhangJiang
	XRSTOR mem XRSTOR64 mem	NP 0F AE /5 NP REX.W 0F AE /5	Restore state components specified by EDX:EAX from memory.
	XGETBV	NP 0F 01 D0	Get value of Extended Control Register. Reads an XCR specified by ECX into EDX:EAX.
	XSETBV	NP 0F 01 D1	Set Extended Control Register. Write the value in EDX:EAX to the XCR specified by ECX.	0
XSAVEOPT Processor Extended State Save/Restore Optimized	XSAVEOPT mem XSAVEOPT64 mem	NP 0F AE /6 NP REX.W 0F AE /6	Save state components specified by EDX:EAX to memory. Unlike the older XSAVE instruction, XSAVEOPT may abstain from writing processor state items to memory when the CPU can determine that they haven't been modified since the most recent corresponding XRSTOR.	3	Sandy Bridge, Steamroller, Puma, Goldmont, ZhangJiang
XSAVEC Processor Extended State save/restore with compaction.	XSAVEC mem XSAVEC64 mem	NP 0F C7 /4 NP REX.W 0F C7 /4	Save processor extended state components specified by EDX:EAX to memory with compaction.	3	Skylake, Goldmont, Zen 1
XSS Processor Extended State save/restore, including supervisor state.	XSAVES mem XSAVES64 mem	NP 0F C7 /5 NP REX.W 0F C7 /5	Save processor extended state components specified by EDX:EAX to memory with compaction and optimization if possible.	0	Skylake, Goldmont, Zen 1
	XRSTORS mem XRSTORS64 mem	NP 0F C7 /3 NP REX.W 0F C7 /3	Restore state components specified by EDX:EAX from memory.

Added with other cross-vendor extensions

Instruction Set Extension	Instruction mnemonics	Opcode	Instruction description	Ring	Added in
SSE (non-SIMD)	PREFETCHNTA m8	0F 18 /0	Prefetch with Non-Temporal Access. Prefetch data under the assumption that the data will be used only once, and attempt to minimize cache pollution from said data. The methods used to minimize cache pollution are implementation-dependent.	3	Pentium III, (K7), (Geode GX2), Nehemiah, Efficeon
	PREFETCHT0 m8	0F 18 /1	Prefetch data to all levels of the cache hierarchy.
	PREFETCHT1 m8	0F 18 /2	Prefetch data to all levels of the cache hierarchy except L1 cache.
	PREFETCHT2 m8	0F 18 /3	Prefetch data to all levels of the cache hierarchy except L1 and L2 caches.
	SFENCE	NP 0F AE F8+x	Store Fence.
SSE2 (non-SIMD)	LFENCE	NP 0F AE E8+x	Load Fence and Dispatch Serialization.	3	Pentium 4, K8, Efficeon, C7 Esther
	MFENCE	NP 0F AE F0+x	Memory Fence.
	MOVNTI m32,r32 MOVNTI m64,r64	NP 0F C3 /r NP REX.W 0F C3 /r	Non-Temporal Memory Store.
	PAUSE	F3 90	Pauses CPU thread for a short time period. Intended for use in spinlocks.
CLFSH Cache Line Flush.	CLFLUSH m8	NP 0F AE /7	Flush one cache line to memory. In a system with multiple cache hierarchy levels and/or multiple processors each with their own caches, the line is flushed from all of them.	3	(SSE2), Geode LX
MONITOR Monitor a memory location for memory writes.	MONITOR MONITOR EAX,ECX,EDX	NP 0F 01 C8	Start monitoring a memory location for memory writes. The memory address to monitor is given by DS:AX/EAX/RAX. ECX and EDX are reserved for extra extension and hint flags, respectively.	Usually 0	Prescott, Yonah, Bonnell, K10, Nano
	MWAIT MWAIT EAX,ECX	NP 0F 01 C9	Wait for a write to a monitored memory location previously specified with MONITOR. ECX and EAX are used to provide extra extension and hint flags, respectively. MWAIT hints are commonly used for CPU power management.
SMX Safer Mode Extensions. Load, authenticate and execute a digitally signed "Authenticated Code Module" as part of Intel Trusted Execution Technology.	GETSEC	NP 0F 37	Perform an SMX function. The leaf function to perform is given in EAX. Depending on leaf function, the instruction may take additional arguments in RBX, ECX and EDX.	Usually 0	Conroe/Merom, WuDaoKou, Tremont
RDTSCP Read Time Stamp Counter and Processor ID.	RDTSCP	0F 01 F9	Read Time Stamp Counter and processor core ID. The TSC value is placed in EDX:EAX and the core ID in ECX.	Usually 3	K8, Nehalem, Silvermont, Nano
POPCNT Population Count.	POPCNT r16,r/m16 POPCNT r32,r/m32	F3 0F B8 /r	Count the number of bits that are set to 1 in its source argument.	3	K10, Nehalem, Nano 3000
	POPCNT r64,r/m64	F3 REX.W 0F B8 /r
SSE4.2 (non-SIMD)	CRC32 r32,r/m8	F2 0F 38 F0 /r	Accumulate CRC value using the CRC-32C (Castagnoli) polynomial 0x11EDC6F41 (normal form 0x1EDC6F41). This is the polynomial used in iSCSI. In contrast to the more popular one used in Ethernet, its parity is even, and it can thus detect any error with an odd number of changed bits.	3	Nehalem, Bulldozer, ZhangJiang
	CRC32 r32,r/m16 CRC32 r32,r/m32	F2 0F 38 F1 /r
	CRC32 r64,r/m64	F2 REX.W 0F 38 F1 /r
FSGSBASE Read/write base address of FS and GS segments from user-mode. Available in 64-bit mode only.	RDFSBASE r32 RDFSBASE r64	F3 0F AE /0 F3 REX.W 0F AE /0	Read base address of FS: segment.	3	Ivy Bridge, Steamroller, Goldmont, ZhangJiang
	RDGSBASE r32 RDGSBASE r64	F3 0F AE /1 F3 REX.W 0F AE /1	Read base address of GS: segment.
	WRFSBASE r32 WRFSBASE r64	F3 0F AE /2 F3 REX.W 0F AE /2	Write base address of FS: segment.
	WRGSBASE r32 WRGSBASE r64	F3 0F AE /3 F3 REX.W 0F AE /3	Write base address of GS: segment.
MOVBE Move to/from memory with byte order swap.	MOVBE r16,m16 MOVBE r32,m32	NFx 0F 38 F0 /r	Load from memory to register with byte-order swap.	3	Bonnell, Haswell, Jaguar, Steamroller, ZhangJiang
	MOVBE r64,m64	NFx REX.W 0F 38 F0 /r
	MOVBE m16,r16 MOVBE m32,r32	NFx 0F 38 F1 /r	Store to memory from register with byte-order swap.
	MOVBE m64,r64	NFx REX.W 0F 38 F1 /r
INVPCID Invalidate TLB entries by Process-context identifier.	INVPCID reg,m128	66 0F 38 82 /r	Invalidate entries in TLB and paging-structure caches based on invalidation type in register and descriptor in m128. The descriptor contains a memory address and a PCID. Instruction is serializing on AMD but not Intel CPUs.	0	Haswell, ZhangJiang, Zen 3, Gracemont
PREFETCHW Cache-line prefetch with intent to write.	PREFETCHW m8	0F 0D /1	Prefetch cache line with intent to write.	3	K6-2, (Cedar Mill), Silvermont, Broadwell, ZhangJiang
	PREFETCH m8	0F 0D /0	Prefetch cache line.
ADX Enhanced variants of add-with-carry.	ADCX r32,r/m32 ADCX r64,r/m64	66 0F 38 F6 /r 66 REX.W 0F 38 F6 /r	Add-with-carry. Differs from the older ADC instruction in that it leaves flags other than EFLAGS.CF unchanged.	3	Broadwell, Zen 1, ZhangJiang, Gracemont
	ADOX r32,r/m32 ADOX r64,r/m64	F3 0F 38 F6 /r F3 REX.W 0F 38 F6 /r	Add-with-carry, with the overflow-flag EFLAGS.OF serving as carry input and output, with other flags left unchanged.
SMAP Supervisor Mode Access Prevention. Repurposes the EFLAGS.AC (alignment check) flag to a flag that prevents access to user-mode memory while in ring 0, 1 or 2.	CLAC	NP 0F 01 CA	Clear EFLAGS.AC.	0	Broadwell, Goldmont, Zen 1, LuJiaZui
	STAC	NP 0F 01 CB	Set EFLAGS.AC.
CLFLUSHOPT Optimized Cache Line Flush.	CLFLUSHOPT m8	NFx 66 0F AE /7	Flush cache line. Differs from the older CLFLUSH instruction in that it has more relaxed ordering rules with respect to memory stores and other cache line flushes, enabling improved performance.	3	Skylake, Goldmont, Zen 1
PREFETCHWT1 Cache-line prefetch into L2 cache with intent to write.	PREFETCHWT1 m8	0F 0D /2	Prefetch data with T1 locality hint (fetch into L2 cache, but not L1 cache) and intent-to-write hint.	3	Knights Landing, YongFeng
PKU Protection Keys for user pages.	RDPKRU	NP 0F 01 EE	Read User Page Key register into EAX.	3	Skylake-X, Comet Lake, Gracemont, Zen 3, LuJiaZui
	WRPKRU	NP 0F 01 EF	Write data from EAX into User Page Key Register, and perform a Memory Fence.
CLWB Cache Line Writeback to memory.	CLWB m8	NFx 66 0F AE /6	Write one cache line back to memory without invalidating the cache line.	3	Skylake-X, Zen 2, Tiger Lake, Tremont
RDPID Read processor core ID.	RDPID r32	F3 0F C7 /7	Read processor core ID into register.	3	Goldmont Plus, Zen 2, Ice Lake, LuJiaZui
MOVDIRI Move to memory as Direct Store.	MOVDIRI m32,r32 MOVDIRI m64,r64	NP 0F 38 F9 /r NP REX.W 0F 38 F9 /r	Store to memory using Direct Store (memory store that is not cached or write-combined with other stores).	3	Tiger Lake, Tremont, Zen 5
MOVDIR64B Move 64 bytes as Direct Store.	MOVDIR64B reg,m512	66 0F 38 F8 /r	Move 64 bytes of data from m512 to address given by ES:reg. The 64-byte write is done atomically with Direct Store.	3	Tiger Lake, Tremont, Zen 5
WBNOINVD Whole Cache Writeback without invalidate.	WBNOINVD	F3 0F 09	Write back all dirty cache lines to memory without invalidation. Instruction is serializing.	0	Zen 2, Ice Lake-SP
PREFETCHI Instruction prefetch.	PREFETCHIT0 m8	0F 18 /7	Prefetch code to all levels of the cache hierarchy.	3	Zen 5, Granite Rapids
	PREFETCHIT1 m8	0F 18 /6	Prefetch code to all levels of the cache hierarchy except first-level cache.

Added with other Intel-specific extensions

Instruction Set Extension	Instruction mnemonics	Opcode	Instruction description	Ring	Added in
SSE2 branch hints Instruction prefixes that can be used with the Jcc instructions to provide branch taken/not-taken hints.	(HWNT)	2E	Instruction prefix: branch hint weakly not taken.	3	Pentium 4, Meteor Lake
	(HST)	3E	Instruction prefix: branch hint strongly taken.
SGX Software Guard Extensions. Set up an encrypted enclave in which a guest can execute code that a compromised or malicious host cannot inspect or tamper with.	ENCLS	NP 0F 01 CF	Perform an SGX Supervisor function. The function to perform is given in EAX - depending on function, the instruction may take additional input operands in RBX, RCX and RDX. Depending on function, the instruction may return data in RBX and/or an error code in EAX.	0	SGX1 Skylake, Goldmont Plus SGX2 Goldmont Plus, Ice Lake-SP OVERSUB Ice Lake-SP, Tremont
	ENCLU	NP 0F 01 D7	Perform an SGX User function. The function to perform is given in EAX - depending on function, the instruction may take additional input operands in RBX, RCX and RDX. Depending on function, the instruction may return data/status information in EAX and/or RCX.	3
	ENCLV	NP 0F 01 C0	Perform an SGX Virtualization function. The function to perform is given in EAX - depending on function, the instruction may take additional input operands in RBX, RCX and RDX. Instruction returns status information in EAX.	0
PTWRITE Write data to a Processor Trace Packet.	PTWRITE r/m32 PTWRITE r/m64	F3 0F AE /4 F3 REX.W 0F AE /4	Read data from register or memory to encode into a PTW packet.	3	Kaby Lake, Goldmont Plus
PCONFIG Platform Configuration, including TME-MK ("Total Memory Encryption – Multi-Key") and TSE ("Total Storage Encryption").	PCONFIG	NP 0F 01 C5	Perform a platform feature configuration function. The function to perform is specified in EAX - depending on function, the instruction may take additional input operands in RBX, RCX and RDX. If the instruction fails, it will set EFLAGS.ZF=1 and return an error code in EAX. If it is successful, it sets EFLAGS.ZF=0 and EAX=0.	0	Ice Lake-SP
CLDEMOTE Cache Line Demotion Hint.	CLDEMOTE m8	NP 0F 1C /0	Move cache line containing m8 from CPU L1 cache to a more distant level of the cache hierarchy.	3	(Tremont), (Alder Lake), Sapphire Rapids
WAITPKG User-mode memory monitoring and waiting.	UMONITOR r16/32/64	F3 0F AE /6	Start monitoring a memory location for memory writes. The memory address to monitor is given by the register argument.	3	Tremont, Alder Lake
	UMWAIT r32 UMWAIT r32,EDX,EAX	F2 0F AE /6	Timed wait for a write to a monitored memory location previously specified with UMONITOR. In the absence of a memory write, the wait will end when either the TSC reaches the value specified by EDX:EAX or the wait has been going on for an OS-controlled maximum amount of time.	Usually 3
	TPAUSE r32 TPAUSE r32,EDX,EAX	66 0F AE /6	Wait until the Time Stamp Counter reaches the value specified in EDX:EAX. The register argument to the UMWAIT and TPAUSE instructions specifies extra flags to control the operation of the instruction.
SERIALIZE Instruction Execution Serialization.	SERIALIZE	NP 0F 01 E8	Serialize instruction fetch and execution.	3	Alder Lake
HRESET Processor History Reset.	HRESET imm8	F3 0F 3A F0 C0 ib	Request that the processor reset selected components of hardware-maintained prediction history. A bitmap of which components of the CPU's prediction history to reset is given in EAX (the imm8 argument is ignored).	0	Alder Lake
UINTR User Interprocessor interrupt. Available in 64-bit mode only.	SENDUIPI reg	F3 0F C7 /6	Send Interprocessor User Interrupt.	3	Sapphire Rapids
	UIRET	F3 0F 01 EC	User Interrupt Return. Pops RIP, RFLAGS and RSP off the stack, in that order.
	TESTUI	F3 0F 01 ED	Test User Interrupt Flag. Copies UIF to EFLAGS.CF .
	CLUI	F3 0F 01 EE	Clear User Interrupt Flag.
	STUI	F3 0F 01 EF	Set User Interrupt Flag.
ENQCMD Enqueue Store. Part of Intel DSA (Data Streaming Accelerator Architecture).	ENQCMD r32/64,m512	F2 0F 38 F8 /r	Enqueue Command. Reads a 64-byte "command data" structure from memory (m512 argument) and writes atomically to a memory-mapped Enqueue Store device (register argument provides the memory address of this device, using ES segment and requiring 64-byte alignment.) Sets ZF=0 to indicate that device accepted the command, or ZF=1 to indicate that command was not accepted (e.g. queue full or the memory location was not an Enqueue Store device.)	3	Sapphire Rapids
	ENQCMDS r32/64,m512	F3 0F 38 F8 /r	Enqueue Command Supervisor. Differs from ENQCMD in that it can place an arbitrary PASID (process address-space identifier) and a privilege-bit in the "command data" to enqueue.	0
WRMSRNS Non-serializing Write to Model-specific register.	WRMSRNS	NP 0F 01 C6	Write Model-specific register. The MSR to write is specified in ECX, and the data to write is given in EDX:EAX. The instruction differs from the older WRMSR instruction in that it is not serializing.	0	Sierra Forest
MSRLIST Read/write multiple Model-specific registers. Available in 64-bit mode only.	RDMSRLIST	F2 0F 01 C6	Read multiple MSRs. RSI points to a table of up to 64 MSR indexes to read (64 bits each), RDI points to a table of up to 64 data items that the MSR read-results will be written to (also 64 bits each), and RCX provides a 64-entry bitmap of which of the table entries to actually perform an MSR read for.	0	Sierra Forest
	WRMSRLIST	F3 0F 01 C6	Write multiple MSRs. RSI points to a table of up to 64 MSR indexes to write (64 bits each), RDI points to a table of up to 64 data items to write into the MSRs (also 64 bits each), and RCX provides a 64-entry bitmap of which of the table entries to actually perform an MSR write for. The instruction is not serializing.
CMPCCXADD Atomically perform a compare - and a fetch-and-add if the condition is met. Available in 64-bit mode only.	CMPccXADD m32,r32,r32 CMPccXADD m64,r64,r64	VEX.128.66.0F38.W0 Ex /r VEX.128.66.0F38.W1 Ex /r	Read value from memory, then compare to first register operand. If the comparison passes, then add the second register operand to the memory value. The instruction as a whole is performed atomically. The operation of CMPccXADD [mem],reg1,reg2 is: temp1 := [mem] EFLAGS := CMP temp1, reg1 // sets EFLAGS like regular compare reg1 := temp1 if( condition ) [mem] := temp1 + reg2	3	Sierra Forest, Lunar Lake
PBNDKB Platform Bind Key to Binary Large Object. Part of Intel TSE (Total Storage Encryption), and available in 64-bit mode only.	PBNDKB	NP 0F 01 C7	Bind information to a platform by encrypting it with a platform-specific wrapping key. The instruction takes as input the addresses to two 256-byte-aligned "bind structures" in RBX and RCX, reads the structure pointed to by RBX and writes a modified structure to the address given in RCX. If the instruction fails, it will set EFLAGS.ZF=1 and return an error code in EAX. If it is successful, it sets EFLAGS.ZF=0 and EAX=0.	0	Lunar Lake

Added with other AMD-specific extensions

Instruction Set Extension	Instruction mnemonics	Opcode	Instruction description	Ring	Added in
AltMovCr8 Alternative mechanism to access the CR8 control register.	MOV reg,CR8	F0 0F 20 /0	Read the CR8 register.	0	K8
	MOV CR8,reg	F0 0F 22 /0	Write to the CR8 register.
MONITORX Monitor a memory location for writes in user mode.	MONITORX	NP 0F 01 FA	Start monitoring a memory location for memory writes. Similar to older MONITOR, except available in user mode.	3	Excavator
	MWAITX	NP 0F 01 FB	Wait for a write to a monitored memory location previously specified with MONITORX. MWAITX differs from the older MWAIT instruction mainly in that it runs in user mode and that it can accept an optional timeout argument (given in TSC time units) in EBX (enabled by setting bit[1] of ECX to 1.)
CLZERO Zero out full cache line.	CLZERO rAX	NP 0F 01 FC	Write zeroes to all bytes in a memory region that has the size and alignment of a CPU cache line and contains the byte addressed by DS:rAX.	3	Zen 1
RDPRU Read processor register in user mode.	RDPRU	NP 0F 01 FD	Read selected MSRs (mainly performance counters) in user mode. ECX specifies which register to read. The value of the MSR is returned in EDX:EAX.	Usually 3	Zen 2
MCOMMIT Commit Stores To Memory.	MCOMMIT	F3 0F 01 FA	Ensure that all preceding stores in thread have been committed to memory, and that any errors encountered by these stores have been signalled to any associated error logging resources. The set of errors that can be reported and the logging mechanism are platform-specific. Sets EFLAGS.CF to 0 if any errors occurred, 1 otherwise.	3	Zen 2
INVLPGB Invalidate TLB Entries with broadcast.	INVLPGB	NP 0F 01 FE	Invalidate TLB Entries for a range of pages, with broadcast. The invalidation is performed on the processor executing the instruction, and also broadcast to all other processors in the system. rAX takes the virtual address to invalidate and some additional flags, ECX takes the number of pages to invalidate, and EDX specifies ASID and PCID to perform TLB invalidation for.	0	Zen 3
	TLBSYNC	NP 0F 01 FF	Synchronize TLB invalidations. Wait until all TLB invalidations signalled by preceding invocations of the INVLPGB instruction on the same logical processor have been responded to by all processors in the system. Instruction is serializing.

x87 floating-point instructions

The x87 coprocessor, if present, provides support for floating-point arithmetic. The coprocessor provides eight data registers, each holding one 80-bit floating-point value (1 sign bit, 15 exponent bits, 64 mantissa bits) – these registers are organized as a stack, with the top-of-stack register referred to as "st" or "st(0)", and the other registers referred to as st(1),st(2),...st(7). It additionally provides a number of control and status registers, including "PC" (precision control, to control whether floating-point operations should be rounded to 24, 53 or 64 mantissa bits) and "RC" (rounding control, to pick rounding-mode: round-to-zero, round-to-positive-infinity, round-to-negative-infinity, round-to-nearest-even) and a 4-bit condition code register "CC", whose four bits are individually referred to as C0,C1,C2 and C3). Not all of the arithmetic instructions provided by x87 obey PC and RC.

Original 8087 instructions

Instruction description	Mnemonic	Opcode	Additional items
x87 Non-Waiting FPU Control Instructions			Waiting mnemonic
Initialize x87 FPU	FNINIT	DB E3	FINIT
Load x87 Control Word	FLDCW m16	D9 /5	(none)
Store x87 Control Word	FNSTCW m16	D9 /7	FSTCW
Store x87 Status Word	FNSTSW m16	DD /7	FSTSW
Clear x87 Exception Flags	FNCLEX	DB E2	FCLEX
Load x87 FPU Environment	FLDENV m112/m224	D9 /4	(none)
Store x87 FPU Environment	FNSTENV m112/m224	D9 /6	FSTENV
Save x87 FPU State, then initialize x87 FPU	FNSAVE m752/m864	DD /6	FSAVE
Restore x87 FPU State	FRSTOR m752/m864	DD /4	(none)
Enable Interrupts (8087 only)	FNENI	DB E0	FENI
Disable Interrupts (8087 only)	FNDISI	DB E1	FDISI
x87 Floating-point Load/Store/Move Instructions			precision control	rounding control
Load floating-point value onto stack	FLD m32	D9 /0	No	—
	FLD m64	DD /0
	FLD m80	DB /5
	FLD st(i)	D9 C0+i
Store top-of-stack floating-point value to memory or stack register	FST m32	D9 /2	No	Yes
	FST m64	DD /2
	FST st(i)	DD D0+i	No	—
Store top-of-stack floating-point value to memory or stack register, then pop	FSTP m32	D9 /3	No	Yes
	FSTP m64	DD /3
	FSTP m80	DB /7	No	—
	FSTP st(i)	DD D8+i
		DF D0+i
		DF D8+i
Push +0.0 onto stack	FLDZ	D9 EE	No	—
Push +1.0 onto stack	FLD1	D9 E8
Push π (approximately 3.14159) onto stack	FLDPI	D9 EB	No	387
Push $\log _{2}\left(10\right)$ (approximately 3.32193) onto stack	FLDL2T	D9 E9
Push $\log _{2}\left(e\right)$ (approximately 1.44269) onto stack	FLDL2E	D9 EA
Push $\log _{10}\left(2\right)$ (approximately 0.30103) onto stack	FLDLG2	D9 EC
Push $\ln \left(2\right)$ (approximately 0.69315) onto stack	FLDLN2	D9 ED
Exchange top-of-stack register with other stack register	FXCH st(i)	D9 C8+i	No	—
		DD C8+i
		DF C8+i
x87 Integer Load/Store Instructions			precision control	rounding control
Load signed integer value onto stack from memory, with conversion to floating-point	FILD m16	DF /0	No	—
	FILD m32	DB /0
	FILD m64	DF /5
Store top-of-stack value to memory, with conversion to signed integer	FIST m16	DF /2	No	Yes
	FIST m32	DB /2
Store top-of-stack value to memory, with conversion to signed integer, then pop stack	FISTP m16	DF /3	No	Yes
	FISTP m32	DB /3
	FISTP m64	DF /7
Load 18-digit Binary-Coded-Decimal integer value onto stack from memory, with conversion to floating-point	FBLD m80	DF /4	No	—
Store top-of-stack value to memory, with conversion to 18-digit Binary-Coded-Decimal integer, then pop stack	FBSTP m80	DF /6	No	387
x87 Basic Arithmetic Instructions			precision control	rounding control
Floating-point add dst <- dst + src	FADD m32	D8 /0	Yes	Yes
	FADD m64	DC /0
	FADD st,st(i)	D8 C0+i
	FADD st(i),st	DC C0+i
Floating-point multiply dst <- dst * src	FMUL m32	D8 /1	Yes	Yes
	FMUL m64	DC /1
	FMUL st,st(i)	D8 C8+i
	FMUL st(i),st	DC C8+i
Floating-point subtract dst <- dst – src	FSUB m32	D8 /4	Yes	Yes
	FSUB m64	DC /4
	FSUB st,st(i)	D8 E0+i
	FSUB st(i),st	DC E8+i
Floating-point reverse subtract dst <- src – dst	FSUBR m32	D8 /5	Yes	Yes
	FSUBR m64	DC /5
	FSUBR st,st(i)	D8 E8+i
	FSUBR st(i),st	DC E0+i
Floating-point divide dst <- dst / src	FDIV m32	D8 /6	Yes	Yes
	FDIV m64	DC /6
	FDIV st,st(i)	D8 F0+i
	FDIV st(i),st	DC F8+i
Floating-point reverse divide dst <- src / dst	FDIVR m32	D8 /7	Yes	Yes
	FDIVR m64	DC /7
	FDIVR st,st(i)	D8 F8+i
	FDIVR st(i),st	DC F0+i
Floating-point compare CC <- result_of( st(0) – src ) Same operation as subtract, except that it updates the x87 CC status register instead of any of the FPU stack registers	FCOM m32	D8 /2	No	—
	FCOM m64	DC /2
	FCOM st(i)	D8 D0+i
		DC D0+i
x87 Basic Arithmetic Instructions with Stack Pop			precision control	rounding control
Floating-point add and pop	FADDP st(i),st	DE C0+i	Yes	Yes
Floating-point multiply and pop	FMULP st(i),st	DE C8+i	Yes	Yes
Floating-point subtract and pop	FSUBP st(i),st	DE E8+i	Yes	Yes
Floating-point reverse-subtract and pop	FSUBRP st(i),st	DE E0+i	Yes	Yes
Floating-point divide and pop	FDIVP st(i),st	DE F8+i	Yes	Yes
Floating-point reverse-divide and pop	FDIVRP st(i),st	DE F0+i	Yes	Yes
Floating-point compare and pop	FCOMP m32	D8 /3	No	—
	FCOMP m64	DC /3
	FCOMP st(i)	D8 D8+i
		DC D8+i
		DE D0+i
Floating-point compare to st(1), then pop twice	FCOMPP	DE D9	No	—
x87 Basic Arithmetic Instructions with Integer Source Argument			precision control	rounding control
Floating-point add by integer	FIADD m16	DA /0	Yes	Yes
	FIADD m32	DE /0
Floating-point multiply by integer	FIMUL m16	DA /1	Yes	Yes
	FIMUL m32	DE /1
Floating-point subtract by integer	FISUB m16	DA /4	Yes	Yes
	FISUB m32	DE /4
Floating-point reverse-subtract by integer	FISUBR m16	DA /5	Yes	Yes
	FISUBR m32	DE /5
Floating-point divide by integer	FIDIV m16	DA /6	Yes	Yes
	FIDIV m32	DE /6
Floating-point reverse-divide by integer	FIDIVR m16	DA /7	Yes	Yes
	FIDIVR m32	DE /7
Floating-point compare to integer	FICOM m16	DA /2	No	—
	FICOM m32	DE /2
Floating-point compare to integer, and stack pop	FICOMP m16	DA /3	No	—
	FICOMP m32	DE /3
x87 Additional Arithmetic Instructions			precision control	rounding control
Floating-point change sign	FCHS	D9 E0	No	—
Floating-point absolute value	FABS	D9 E1	No	—
Floating-point compare top-of-stack value to 0	FTST	D9 E4	No	—
Classify top-of-stack st(0) register value. The classification result is stored in the x87 CC register.	FXAM	D9 E5	No	—
Split the st(0) value into two values E and M representing the exponent and mantissa of st(0). The split is done such that $M*2^{E}=st(0)$, where E is an integer and M is a number whose absolute value is within the range $1\leq \left|M\right|<2$.   st(0) is then replaced with E, after which M is pushed onto the stack.	FXTRACT	D9 F4	No	—
Floating-point partial remainder (not IEEE 754 compliant):$$Q\leftarrow {\mathtt {IntegerRoundToZero}}\left({\frac {st(0)}{st(1)}}\right)$$$$st(0)\leftarrow st(0)-st(1)*Q$$	FPREM	D9 F8	No	—
Floating-point square root	FSQRT	D9 FA	Yes	Yes
Floating-point round to integer	FRNDINT	D9 FC	No	Yes
Floating-point power-of-2 scaling. Rounds the value of st(1) to integer with round-to-zero, then uses it as a scale factor for st(0):$$st(0)\leftarrow st(0)*2^{{\mathtt {IntegerRoundToZero}}\left(st(1)\right)}$$	FSCALE	D9 FD	No	Yes
x87 Transcendental Instructions			Source operand range restriction
Base-2 exponential minus 1, with extra precision for st(0) close to 0:$$st(0)\leftarrow 2^{st(0)}-1$$	F2XM1	D9 F0	8087: $0\leq st(0)\leq {\frac {1}{2}}$ 80387: $-1\leq st(0)\leq 1$
Base-2 Logarithm:$$st(1)\leftarrow st(1)*\log _{2}\left(st(0)\right)$$followed by stack pop	FYL2X	D9 F1	no restrictions
Partial Tangent: Computes from st(0) a pair of values X and Y, such that$$\tan \left(st(0)\right)={\frac {Y}{X}}$$The Y value replaces the top-of-stack value, and then X is pushed onto the stack. On 80387 and later x87, but not original 8087, X is always 1.0	FPTAN	D9 F2	8087: $0\leq \left|st(0)\right|\leq {\frac {\pi }{4}}$ 80387: $0\leq \left|st(0)\right|<2^{63}$
Two-argument arctangent with quadrant adjustment:$$st(1)\leftarrow \arctan \left({\frac {st(1)}{st(0)}}\right)$$ followed by stack pop	FPATAN	D9 F3	8087: $\left|st(1)\right|\leq \left|st(0)\right|<\infty$ 80387: no restrictions
Base-2 Logarithm plus 1, with extra precision for st(0) close to 0:$$st(1)\leftarrow st(1)*\log _{2}\left(st(0)+1\right)$$followed by stack pop	FYL2XP1	D9 F9	Intel: $\left|st(0)\right|<\left(1-{\sqrt {\frac {1}{2}}}\right)$ AMD: $\left({\sqrt {\frac {1}{2}}}-1\right)<st(0)<\left({\sqrt {2}}-1\right)$
Other x87 Instructions
No operation	FNOP	D9 D0
Decrement x87 FPU Register Stack Pointer	FDECSTP	D9 F6
Increment x87 FPU Register Stack Pointer	FINCSTP	D9 F7
Free x87 FPU Register	FFREE st(i)	DD C0+i
Check and handle pending unmasked x87 FPU exceptions	WAIT, FWAIT	9B
Floating-point store and pop, without stack underflow exception	FSTPNCE st(i)	D9 D8+i
Free x87 register, then stack pop	FFREEP st(i)	DF C0+i

x87 instructions added in later processors

Instruction description	Mnemonic	Opcode	Additional items
x87 Non-Waiting Control Instructions added in 80287			Waiting mnemonic
Notify FPU of entry into Protected Mode	FNSETPM	DB E4	FSETPM
Store x87 Status Word to AX	FNSTSW AX	DF E0	FSTSW AX
x87 Instructions added in 80387			Source operand range restriction
Floating-point unordered compare. Similar to the regular floating-point compare instruction FCOM, except will not produce an exception in response to any qNaN operands.	FUCOM st(i)	DD E0+i	no restrictions
Floating-point unordered compare and pop	FUCOMP st(i)	DD E8+i
Floating-point unordered compare to st(1), then pop twice	FUCOMPP	DA E9
IEEE 754 compliant floating-point partial remainder.	FPREM1	D9 F5
Floating-point sine and cosine. Computes two values $S=\sin \left(k*st(0)\right)$ and $C=\cos \left(k*st(0)\right)$  Top-of-stack st(0) is replaced with S, after which C is pushed onto the stack.	FSINCOS	D9 FB	$\left|st(0)\right|<2^{63}$
Floating-point sine.$$st(0)\leftarrow \sin \left(k*st(0)\right)$$	FSIN	D9 FE
Floating-point cosine.$$st(0)\leftarrow \cos \left(k*st(0)\right)$$	FCOS	D9 FF
x87 Instructions added in Pentium Pro			Condition for conditional moves
Floating-point conditional move to st(0) based on EFLAGS	FCMOVB st(0),st(i)	DA C0+i	below (CF=1)
	FCMOVE st(0),st(i)	DA C8+i	equal (ZF=1)
	FCMOVBE st(0),st(i)	DA D0+i	below or equal (CF=1 or ZF=1)
	FCMOVU st(0),st(i)	DA D8+i	unordered (PF=1)
	FCMOVNB st(0),st(i)	DB C0+i	not below (CF=0)
	FCMOVNE st(0),st(i)	DB C8+i	not equal (ZF=0)
	FCMOVNBE st(0),st(i)	DB D0+i	not below or equal (CF=0 and ZF=0)
	FCMOVNU st(0),st(i)	DB D8+i	not unordered (PF=0)
Floating-point compare and set EFLAGS. Differs from the older FCOM floating-point compare instruction in that it puts its result in the integer EFLAGS register rather than the x87 CC register.	FCOMI st(0),st(i)	DB F0+i
Floating-point compare and set EFLAGS, then pop	FCOMIP st(0),st(i)	DF F0+i
Floating-point unordered compare and set EFLAGS	FUCOMI st(0),st(i)	DB E8+i
Floating-point unordered compare and set EFLAGS, then pop	FUCOMIP st(0),st(i)	DF E8+i
x87 Non-Waiting Instructions added in Pentium II, AMD K7 and SSE			64-bit mnemonic (REX.W prefix)
Save x87, MMX and SSE state to 512-byte data structure	FXSAVE m512byte	NP 0F AE /0	FXSAVE64 m512byte
Restore x87, MMX and SSE state from 512-byte data structure	FXRSTOR m512byte	NP 0F AE /1	FXRSTOR64 m512byte
x87 Instructions added as part of SSE3
Floating-point store integer and pop, with round-to-zero	FISTTP m16	DF /1
	FISTTP m32	DB /1
	FISTTP m64	DD /1

SIMD instructions

Main article: x86 SIMD instruction listings

Cryptographic instructions

Main article: List of x86 cryptographic instructions

Virtualization instructions

Main article: List of x86 virtualization instructions

Other instructions

See also: List of discontinued x86 instructions

x86 also includes discontinued instruction sets which are no longer supported by Intel and AMD, and undocumented instructions which execute but are not officially documented.

Undocumented x86 instructions

The x86 CPUs contain undocumented instructions which are implemented on the chips but not listed in some official documents. They can be found in various sources across the Internet, such as Ralf Brown's Interrupt List and at sandpile.org

Some of these instructions are widely available across many/most x86 CPUs, while others are specific to a narrow range of CPUs.

Undocumented instructions that are widely available across many x86 CPUs include

Mnemonics	Opcodes	Description	Status
AAM imm8	D4 ib	ASCII-Adjust-after-Multiply. On the 8086, documented for imm8=0Ah only, which is used to convert a binary multiplication result to BCD. The actual operation is AH ← AL/imm8; AL ← AL mod imm8 for any imm8 value (except zero, which produces a divide-by-zero exception).	Available beginning with 8086, documented for imm8 values other than 0Ah since Pentium (earlier documentation lists no arguments).
AAD imm8	D5 ib	ASCII-Adjust-Before-Division. On the 8086, documented for imm8=0Ah only, which is used to convert a BCD value to binary for a following division instruction. The actual operation is AL ← (AL+(AH*imm8)) & 0FFh; AH ← 0 for any imm8 value.
SALC, SETALC	D6	Set AL depending on the value of the Carry Flag (a 1-byte alternative of SBB AL, AL)	Available beginning with 8086, but only documented since Pentium Pro.
ICEBP, INT1	F1	Single byte single-step exception / Invoke ICE	Available beginning with 80386, documented (as INT1) since Pentium Pro. Executes as undocumented instruction prefix on 8086 and 80286.
TEST r/m8,imm8	F6 /1 ib	Undocumented variants of the TEST instruction. Performs the same operation as the documented F6 /0 and F7 /0 variants, respectively.	Available since the 8086. Unavailable on some 80486 steppings.
TEST r/m16,imm16, TEST r/m32,imm32	F7 /1 iw, F7 /1 id
SHL, SAL	(D0..D3) /6, (C0..C1) /6 ib	Undocumented variants of the SHL instruction. Performs the same operation as the documented (D0..D3) /4 and (C0..C1) /4 ib variants, respectively.	Available since the 80186 (performs different operation on the 8086)
(multiple)	82 /(0..7) ib	Alias of opcode 80h, which provides variants of 8-bit integer instructions (ADD, OR, ADC, SBB, AND, SUB, XOR, CMP) with an 8-bit immediate argument.	Available since the 8086. Explicitly unavailable in 64-bit mode but kept and reserved for compatibility.
OR/AND/XOR r/m16,imm8	83 /(1,4,6) ib	16-bit OR/AND/XOR with a sign-extended 8-bit immediate.	Available on 8086, but only documented from 80386 onwards.
REPNZ MOVS	F2 (A4..A5)	The behavior of the F2 prefix (REPNZ, REPNE) when used with string instructions other than CMPS/SCAS is officially undefined, but there exists commercial software (e.g. the version of FDISK distributed with MS-DOS versions 3.30 to 6.22) that rely on it to behave in the same way as the documented F3 (REP) prefix.	Available since the 8086.
REPNZ STOS	F2 (AA..AB)
REP RET	F3 C3	The use of the REP prefix with the RET instruction is not listed as supported in either the Intel SDM or the AMD APM. However, AMD's optimization guide for the AMD-K8 describes the F3 C3 encoding as a way to encode a two-byte RET instruction – this is the recommended workaround for an issue in the AMD-K8's branch predictor that can cause branch prediction to fail for some 1-byte RET instructions. At least some versions of gcc are known to use this encoding.	Executes as RET on all known x86 CPUs.
NOP	67 90	NOP with address-size override prefix. The use of the 67h prefix for instructions without memory operands is listed by the Intel SDM (vol 2, section 2.1.1) as "reserved", but it is used in Microsoft Windows 95 as a workaround for a bug in the B1 stepping of Intel 80386.	Executes as NOP on 80386 and later.
NOP r/m	0F 1F /0	Official long NOP. Introduced in the Pentium Pro in 1995, but remained undocumented until March 2006.	Available on Pentium Pro and AMD K7 and later. Unavailable on AMD K6, AMD Geode LX, VIA Nehemiah.
NOP r/m	0F 0D /r	Reserved-NOP. Introduced in 65 nm Pentium 4. Intel documentation lists this opcode as NOP in opcode tables but not instruction listings since June 2005. From Broadwell onwards, 0F 0D /1 has been documented as PREFETCHW, while 0F 0D /0 and /2../7 have been reported to exhibit undocumented prefetch functionality. On AMD CPUs, 0F 0D /r with a memory argument is documented as PREFETCH/PREFETCHW since K6-2 – originally as part of 3Dnow!, but has been kept in later AMD CPUs even after the rest of 3Dnow! was dropped.	Available on Intel CPUs since 65 nm Pentium 4.
UD1	0F B9 /r	Intentionally undefined instructions, but unlike UD2 (0F 0B) these instructions were left unpublished until December 2016. Microsoft Windows 95 Setup is known to depend on 0F FF being invalid – it is used as a self check to test that its #UD exception handler is working properly. Other invalid opcodes that are being relied on by commercial software to produce #UD exceptions include FF FF (DIF-2, LaserLok) and C4 C4 ("BOP"), however as of January 2022 they are not published as intentionally invalid opcodes.	All of these opcodes produce #UD exceptions on 80186 and later (except on NEC V20/V30, which assign at least 0F FF to the NEC-specific BRKEM instruction.)
UD0	0F FF

Undocumented instructions that appear only in a limited subset of x86 CPUs include

Mnemonics	Opcodes	Description	Status
REP MUL	F3 F6 /4, F3 F7 /4	On 8086/8088, a REP or REPNZ prefix on a MUL or IMUL instruction causes the result to be negated. This is due to the microcode using the “REP prefix present” bit to store the sign of the result.	8086/8088 only.
REP IMUL	F3 F6 /5, F3 F7 /5
REP IDIV	F3 F6 /7, F3 F7 /7	On 8086/8088, a REP or REPNZ prefix on an IDIV (but not DIV) instruction causes the quotient to be negated. This is due to the microcode using the “REP prefix present” bit to store the sign of the quotient.	8086/8088 only.
SAVEALL, STOREALL	(F1) 0F 04	Exact purpose unknown, causes CPU hang (HCF). The only way out is CPU reset. In some implementations, emulated through BIOS as a halting sequence. In a forum post at the Vintage Computing Federation, this instruction (with F1 prefix) is explained as SAVEALL. It interacts with ICE mode.	Only available on 80286.
LOADALL	0F 05	Loads All Registers from Memory Address 0x000800H	Only available on 80286. Opcode reused for SYSCALL in AMD K6 and later CPUs.
LOADALLD	0F 07	Loads All Registers from Memory Address ES:EDI	Only available on 80386. Opcode reused for SYSRET in AMD K6 and later CPUs.
CL1INVMB	0F 0A	On the Intel SCC (Single-chip Cloud Computer), invalidate all message buffers. The mnemonic and operation of the instruction, but not its opcode, are described in Intel's SCC architecture specification.	Available on the SCC only.
PATCH2	0F 0E	On AMD K6 and later maps to FEMMS operation (fast clear of MMX state) but on Intel identified as uarch data read on Intel	Only available in Red unlock state (0F 0F too)
PATCH3	0F 0F	Write uarch	Can change RAM part of microcode on Intel
UMOV r,r/m, UMOV r/m,r	0F (10..13) /r	Moves data to/from user memory when operating in ICE HALT mode. Acts as regular MOV otherwise.	Available on some 386 and 486 processors only. Opcodes reused for SSE instructions in later CPUs.
NXOP	0F 55	NexGen hypercode interface.	Available on NexGen Nx586 only.
(multiple)	0F (E0..FB)	NexGen Nx586 "hyper mode" instructions. The NexGen Nx586 CPU uses "hyper code" (x86 code sequences unpacked at boot time and only accessible in a special "hyper mode" operation mode, similar to DEC Alpha's PALcode and Intel's XuCode) for many complicated operations that are implemented with microcode in most other x86 CPUs. The Nx586 provides a large number of undocumented instructions to assist hyper mode operation.	Available in Nx586 hyper mode only.
PSWAPW mm,mm/m64	0F 0F /r BB	Undocumented AMD 3DNow! instruction on K6-2 and K6-3. Swaps 16-bit words within 64-bit MMX register. Instruction known to be recognized by MASM 6.13 and 6.14.	Available on K6-2 and K6-3 only. Opcode reused for documented PSWAPD instruction from AMD K7 onwards.
Un­known mnemonic	64 D6	Using the 64 (FS: segment) prefix with the undocumented D6 (SALC/SETALC) instruction will, on UMC CPUs only, cause EAX to be set to 0xAB6B1B07.	Available on the UMC Green CPU only. Executes as SALC on non-UMC CPUs.
FS: Jcc	64 (70..7F) rel8, 64 0F (80..8F) rel16/32	On Intel NetBurst (Pentium 4) CPUs, the 64h (FS: segment) instruction prefix will, when used with conditional branch instructions, act as a branch hint to indicate that the branch will be alternating between taken and not-taken. Unlike other NetBurst branch hints (CS: and DS: segment prefixes), this hint is not documented.	Available on NetBurst CPUs only. Segment prefixes on conditional branches are accepted but ignored by non-NetBurst CPUs.
JMPAI	0F 3F	Jump and execute instructions in the undocumented Alternate Instruction Set.	Only available on some x86 processors made by VIA Technologies.
(FMA4)	VEX.66.0F38 (5C..5F,68..6F,78..7F) /r imm8	On AMD Zen1, FMA4 instructions are present but undocumented (missing CPUID flag). The reason for leaving the feature undocumented may or may not have been due to a buggy implementation.	Removed from Zen2 onwards.
(unknown, multiple)	0F 0F /r ??	The whitepapers for SandSifter and UISFuzz report the detection of large numbers of undocumented instructions in the 3DNow! opcode range on several different AMD CPUs (at least Geode NX and C-50). Their operation is not known. On at least AMD K6-2, all of the unassigned 3DNow! opcodes (other than the undocumented PF2IW, PI2FW and PSWAPW instructions) are reported to execute as equivalents of POR (MMX bitwise-OR instruction).	Present on some AMD CPUs with 3DNow!.
MOVDB, GP2MEM	Un­known	Microprocessor Report's article "MediaGX Targets Low-Cost PCs" from 1997, covering the introduction of the Cyrix MediaGX processor, lists several new instructions that are said to have been added to this processor in order to support its new "Virtual System Architecture" features, including MOVDB and GP2MEM – and also mentions that Cyrix did not intend to publish specifications for these instructions.	Unknown. No specification known to have been published.
REP XSHA512	F3 0F A6 E0	Perform SHA-512 hashing. Supported by OpenSSL as part of its VIA PadLock support, and listed in a Zhaoxin-supplied Linux kernel patch, but not documented by the VIA PadLock Programming Guide.	Only available on some x86 processors made by VIA Technologies and Zhaoxin.
REP XMODEXP	F3 0F A6 F8	Instructions to perform modular exponentiation and random number generation, respectively. Listed in a VIA-supplied patch to add support for VIA Nano-specific PadLock instructions to OpenSSL, but not documented by the VIA PadLock Programming Guide.
XRNG2	F3 0F A7 F8
Un­known mnemonic	0F A7 (C1..C7)	Detected by CPU fuzzing tools such as SandSifter and UISFuzz as executing without causing #UD on several different VIA and Zhaoxin CPUs. Unknown operation, may be related to the documented XSTORE (0F A7 C0) instruction.
Un­known mnemonic	F2 0F A6 C0	Zhaoxin SM2 instruction. CPUID flags listed in a Linux kernel patch for OpenEuler, description and opcode (but no instruction mnemonic) provided in a Zhaoxin patent application and a Zhaoxin-provided Linux kernel patch.	Present in Zhaoxin KX-6000G.
ZXPAUSE	F2 0F A6 D0	Pause the processor until the Time Stamp Counter reaches or exceeds the value specified in EDX:EAX. Low-power processor C-state can be requested in ECX. Listed in OpenEuler kernel patch.	Present in Zhaoxin KX-7000.
MONTMUL2	Un­known	Zhaoxin RSA/"xmodx" instructions. Mnemonics and CPUID flags are listed in a Linux kernel patch for OpenEuler, but opcodes and instruction descriptions are not available.	Unknown. Some Zhaoxin CPUs have the CPUID flags for these instructions set.

Undocumented x87 instructions

Mnemonics	Opcodes	Description	Status
FENI, FENI8087_NOP	DB E0	FPU Enable Interrupts (8087)	Documented for the Intel 80287. Present on all Intel x87 FPUs from 80287 onwards. For FPUs other than the ones where they were introduced on (8087 for FENI/FDISI and 80287 for FSETPM), they act as NOPs. These instructions and their operation on modern CPUs are commonly mentioned in later Intel documentation, but with opcodes omitted and opcode table entries left blank (e.g. Intel SDM 325462-077, April 2022 mentions them twice without opcodes). The opcodes are, however, recognized by Intel XED.
FDISI, FDISI8087_NOP	DB E1	FPU Disable Interrupts (8087)
FSETPM, FSETPM287_NOP	DB E4	FPU Set Protected Mode (80287)
(no mnemonic)	D9 D7,  D9 E2, D9 E7,  DD FC, DE D8,  DE DA, DE DC,  DE DD, DE DE,  DF FC	"Reserved by Cyrix" opcodes	These opcodes are listed as reserved opcodes that will produce "unpredictable results" without generating exceptions on at least Cyrix 6x86, 6x86MX, MII, MediaGX, and AMD Geode GX/LX. (The documentation for these CPUs all list the same ten opcodes.) Their actual operation is not known, nor is it known whether their operation is the same on all of these CPUs.

See also

• CLMUL
• RDRAND
• Advanced Vector Extensions 2
• AVX-512
• x86 Bit manipulation instruction set
• CPUID
• List of discontinued x86 instructions

References

• Intel Corporation (April 2022). "Intel 64 and IA-32 Architectures Software Developer's Manual, Combined Volumes: 1, 2A, 2B, 2C, 2D, 3A, 3B, 3C, 3D and 4". Intel. Retrieved 21 June 2022.

External links

• Free IA-32 and x86-64 documentation, provided by Intel
• AMD64 Architecture Programmer's Manual, Volumes 1-5, provided by AMD
• x86 Opcode and Instruction Reference
• x86 and amd64 instruction reference
• Instruction tables: Lists of instruction latencies, throughputs and micro-operation breakdowns for Intel, AMD and VIA CPUs
• Netwide Assembler Instruction List (from Netwide Assembler)