Maglev
This article has multiple issues. Please help improve it or discuss these issues on the talk page. (Learn how and when to remove these messages)
No issues specified. Please specify issues, or remove this template. |
A maglev, or magnetically levitating, train is a form of transportation that suspends, guides and propels vehicles (predominantly trains) using electromagnetic force. This method has the potential to be fast and quiet when compared to wheeled mass transit systems, potentially reaching velocities comparable to turboprop and jet aircraft (900 km/h, 600 mph). The highest recorded speed of a maglev train is 581 km/h (361 mph), achieved in Japan in 2003, 6 km/h higher than the conventional TGV speed record.
History
In the 1960s, Great Britain held the lead in maglev research;[1] however, research in the United States was short-lived.
In Britain, Eric Laithwaite, Professor of Heavy Electrical Engineering at Imperial College, developed a functional maglev passenger vehicle. It weighed 1 ton (1 tonne) and could carry four passengers.[1] Additional funding for his work was also provided by British Rail, the British Transport Commission, Manchester University, Surrey University and the Wolfson Foundation.[1] His maglev had one mile (1.6 km) of track and was thoroughly tested, but his research was cut off in 1973 due to lack of funding; and his progress was not sufficient. British Rail also set up a Maglev Experimental Centre at their Railway Technical Centre based at Derby.
In the 1970s, Germany and Japan also began research and after some failures both nations developed mature technologies in the 1990s.
However, superconductor related costs remain a barrier to widespread acceptance.[citation needed]
Commercial operation
The first commercial Maglev "people-mover" was officially opened in 1984 in Birmingham, England. It operated on an elevated 600 metres (1,969 ft) section of monorail track between Birmingham International Airport and Birmingham International railway station. It ran at 42 km/h (26 mph) until the system was eventually closed in 1995 due to reliability and design problems.
The best-known high-speed maglev currently operating commercially is the IOS (initial operating segment) demonstration line of the German built Transrapid train in Shanghai, China that transports people 30 km (18.6 miles) to the airport in just 7 minutes 20 seconds, achieving a top velocity of 431 km/h (268 mph), averaging 250 km/h (150 mph).
Other commercially operating lines exist in Japan, such as the Linimo line. Maglev projects worldwide are being studied for feasibility. In Japan at the Yamanashi test track, current maglev train technology is mature, but costs and problems remain a barrier to development, alternative technologies are being developed to address those issues.
Technology
All operational implementations of maglev technology have had minimal overlap with wheeled train technology and have not been compatible with conventional rail tracks. Because they cannot share existing infrastructure, maglevs must be designed as complete transportation systems. The term "maglev" refers not only to the vehicles, but to the railway system as well, specifically designed for magnetic levitation and propulsion.
- See also fundamental technology elements in the JR-Maglev article, Technology in the Transrapid article, Magnetic levitation
There are two primary types of maglev technology:
- electromagnetic suspension (EMS) uses the attractive magnetic force of a magnet beneath a rail to lift the train up.
- electrodynamic suspension (EDS) uses a repulsive force between two magnetic fields to push the train away from the rail.
Another experimental technology, which was designed, proven mathematically, peer reviewed, and patented, but is yet to be built, is the magnetodynamic suspension (MDS), which uses the attractive magnetic force of a permanent magnet array near a steel track to lift the train and hold it in place.
Electromagnetic suspension
In current EMS systems, the train levitates above a steel rail while electromagnets, attached to the train, are oriented toward the rail from below. The electromagnets use feedback control to maintain a train at a constant distance from the track, at approximately Template:Mm to in.[2][3]
Electrodynamic suspension
In Electrodynamic suspension (EDS), both the rail and the train exert a magnetic field, and the train is levitated by the repulsive force between these magnetic fields. The magnetic field in the train is produced by either electromagnets (as in JR-Maglev) or by an array of permanent magnets (as in Inductrack). The repulsive force in the track is created by an induced magnetic field in wires or other conducting strips in the track.
At slow speeds, the current induced in these coils and the resultant magnetic flux is not large enough to support the weight of the train. For this reason the train must have wheels or some other form of landing gear to support the train until it reaches a speed that can sustain levitation.
Propulsion coils on the guideway are used to exert a force on the magnets in the train and make the train move forward. The propulsion coils that exert a force on the train are effectively a linear motor: An alternating current flowing through the coils generates a continuously varying magnetic field that moves forward along the track. The frequency of the alternating current is synchronized to match the speed of the train. The offset between the field exerted by magnets on the train and the applied field create a force moving the train forward.
Magnetodynamic suspension
Magnetodynamic suspension, invented by Dr. Oleg Tozoni, is similar to the EMS system in that it uses attractive forces, but differs in that the magnets used for suspension are permanent, and the stability is built into the system itself using physics/mechanical systems, as opposed to EMS's computer systems. MDS is based on the idea of using a minimum energy point to balance the train. A simple way to explain this is to compare EMS to a hill, with minimum energy points on the sides of it, and MDS to a valley with the minimum point in the center. The center of each would be the vehicle's suspended center point. If you put a ball on the top of the hill and apply any force to it, the ball will try to roll down, and you would need to apply a compensation force in the other direction to keep it centered. Once the ball gets to the top of the hill, it will try to keep rolling down the other side, and an opposite, compensating force is needed. This is what EMS does when it uses stabilising systems to increase or decrease the strength of the electromagnets holding the train suspended, and that system is inherently unstable, requiring a constant outside stabilising force. MDS, on the other hand, is more like a valley with the energy minimum in the center. It takes energy to move the ball away from the bottom, and the ball returns to the bottom on its own. This is possible because steel magnetic permeability is highly dependent on magnetic flux intensity in that steel. Basically, the more you magnetize steel, the more difficult it is to magnetize it even more. Once the steel becomes fully saturated, bringing a magnet closer to it will not increase the strength of the magnetic field between the magnet and the magnetically saturated steel. Dr. Tozoni figured out how to create what is essentially magnetic insulation, which would keep magnetic fields escaping from the steel rails into the surrounding air, thus concentrating the magnetic field in those rails and saturating them. MDS uses a series of magnets constructed in such a way that when the array is suspended within the steel rail, the lateral, side-to-side, forces pulling the train towards the steel rails become much weaker than the horizontal, up-down, force holding the magnets centered between the rails. When two such magnet arrays are arranged perpendicular to each other, the stronger forces cancel out the weaker forces, forcing the train to stay centered between the rails automatically, thus holding it in the minimum energy point; any outside force that moves the train away from the center line of travel is countered by a force wanting to bring the train back to the center minimum. AMLEVTrans
Pros and cons of different technologies
Each implementation of the magnetic levitation principle for train-type travel involves advantages and disadvantages. Time will tell us which principle, and whose implementation, wins out commercially.
Technology | Pros | Cons | ||
EMS (Electromagnetic) | Magnetic fields inside and outside the vehicle are insignificant; proven, commercially available technology that can attain very high speeds (500 km/h); no wheels or secondary propulsion system needed |
The separation between the vehicle and the guideway must be constantly monitored and corrected by computer systems to avoid collision due to the unstable nature of electromagnetic attraction; due to the system's inherent instability and the required constant corrections by outside systems, vibration issues may occur. | ||
EDS (Electrodynamic) | Onboard magnets and large margin between rail and train enable highest recorded train speeds (581 km/h) and heavy load capacity; has recently demonstrated (December 2005) successful operations using high temperature superconductors in its onboard magnets, cooled with inexpensive liquid nitrogen |
Strong magnetic fields onboard the train would make the train inaccessible to passengers with pacemakers or magnetic data storage media such as hard drives and credit cards, necessitating the use of magnetic shielding; limitations on guideway inductivity limit the maximum speed of the vehicle; vehicle must be wheeled for travel at low speeds; system per mile cost still considered prohibitive; the system is not yet out of prototype phase. | ||
Inductrack System (Permanent Magnet EDS) | Failsafe Suspension - no power required to activate magnets; Magnetic field is localized below the car; can generate enough force at low speeds (around 5 km/h) to levitate maglev train; in case of power failure cars slow down on their own safely; Halbach arrays of permanent magnets may prove more cost-effective than electromagnets |
Requires either wheels or track segments that move for when the vehicle is stopped. New technology that is still under development (as of 2007) and has as yet no commercial version or full scale system prototype. | ||
MDS (Magnetodynamic) |
Failsafe Suspension - no power required to activate magnets; separation between vehicle and guideway is automatic, requiring no outside control or monitoring; attractive force of permanent magnets is far greater than the repulsive or Halbach array force, thus smaller, cheaper magnets can be used; magnetic fields inside and outside vehicle are insignificant; in case of power failure, cars safely slow down on their own; entire system is designed using physics and mathematic calculations, and all aspects of it, including resulting forces, can be calculated, designed, and improved upon on paper or computers before construction, thus not requiring costly experiments with test models; because permanent magnets and steel is used, there is no limit, within the system itself, on the speed the train can achieve while still being able to stay suspended. |
Because guideway insulation works via vehicle-generated eddy currents, the vehicle must be wheeled to travel at low speeds; guideway construction requires laminated steel encased in aluminum cores, all of which must be made to exact specifications, and thus may prove costly. Although tested via computer simulation, technology is still entirely theoretical. | ||
Neither Inductrack nor the Superconducting EDS nor the MDS are able to levitate vehicles at a standstill, although Inductrack provides levitation down to a much lower speed. Wheels are required for these systems. EMS systems are wheel-less. The German Transrapid, Japanese HSST (Linimo), and Korean Rotem EMS maglevs levitate at a standstill, with electricity extracted from guideway using power rails for the latter two, and wirelessly for Transrapid. If guideway power is lost on the move, the Transrapid is still able to generate levitation down to 10 km/h speed, using the power from onboard batteries. This is not the case with the HSST and Rotem systems. PropulsionAn EMS system can provide both levitation and propulsion using an onboard linear motor. EDS systems can only levitate the train using the magnets onboard, not propel it forward. As such, vehicles need some other technology for propulsion. A linear motor (propulsion coils) mounted in the track is one solution. Over long distances where the cost of propulsion coils could be prohibitive, a propeller or jet engine could be used. StabilityEarnshaw's theorem shows that any combination of static magnets cannot be in a stable equilibrium. However, the various levitation systems achieve stable levitation by violating the assumptions of Earnshaw's theorem. Earnshaw's theorem assumes that the magnets are static and unchanging in field strength and that permeability is constant everywhere. EMS systems rely on active electronic stabilization. Such systems constantly measure the bearing distance and adjust the electromagnet current accordingly. All EDS systems are moving systems (no EDS system can levitate the train unless it is in motion). MDS systems use materials with non-uniform permeability. Pros and cons of maglev vs. conventional trainsMaglev trains are not compatible with conventional track, and therefore require all new infrastructure for their entire route. By contrast conventional high speed trains such as the TGV are able to run at reduced speeds on existing rail infrastructure, thus reducing expenditure where new infrastructure would be particularly expensive (such as the final approaches to city terminals), or on extensions where traffic does not justify new infrastructure. Due to the lack of physical contact between the track and the vehicle, Maglev trains experience no rolling friction, leaving only air resistance and electromagnetic drag, potentially improving power efficiency.[4] The weight of the large electromagnets in EMS and EDS designs is a major design issue. A very strong magnetic field is required to levitate a massive train. For this reason one research path is using superconductors to improve the efficiency of the electromagnets. The high speed of some maglev trains translates to more sound due to air displacement, which gets louder as the trains go faster. A study found that high speed maglev trains are 5 dB noisier than traditional trains.[5] At low speeds, however, maglev trains are nearly silent. However, two trains passing at a combined 1,000 km/h has been successfully demonstrated without major problems in Japan. Braking issues and overhead wire wear are problems for the Fastech 360 railed Shinkansen. Maglev would eliminate these issues, but not the noise pollution issue. One advantage of maglev's higher speed would be extension of the serviceable area (3 hours radius) that can outcompete subsonic commercial aircraft. Issues relating to magnets are also a factor. See suspension types. As linear motors must fit within or straddle their track over the full length of the train, track design is challenging for anything other than point-to-point services. Curves must be gentle and avoid camber, while switches are very long and need care to avoid breaks in current. Maglev needs very fast-responding control systems to maintain a stable height above the track; this needs careful design in the event of a failure in order to avoid crashing into the track during a power fluctuation. EconomicsThe Shanghai maglev cost 9.93 billion yuan (US$1.2 billion) to build.[6] This total includes infrastructure capital costs such as manufacturing and construction facilities, and operational training. At 50 yuan per passenger[7] and the current 7,000 passengers per day, income from the system is incapable of recouping the capital costs (including interest on financing) over the expected lifetime of the system, even ignoring operating costs. China aims to limit the cost of future construction extending the maglev line to approximately 200 million yuan (US$24.6 million) per kilometer.[6] These costs compare competitively with airport construction (e.g., Hong Kong Airport cost US$20 billion to build in 1998) and eight-lane Interstate highway systems that cost around US$50 million per mile (US$31 million per kilometer) in the US. While high-speed maglevs are expensive to build, they are less expensive to operate and maintain than traditional high-speed trains, planes or intercity buses.[citation needed] Data from the Shanghai maglev project indicates that operation and maintenance costs are covered by the current relatively low volume of 7,000 passengers per day.[citation needed] Passenger volumes on the Pudong International Airport line are expected to rise dramatically once the line is extended from Longyang Road metro station all the way to Shanghai's downtown train depot. The proposed Chūō Shinkansen maglev in Japan is estimated to cost approximately US$82 billion to build, with a route blasting long tunnels through mountains. A Tokaido maglev route replacing current Shinkansen would cost some 1/10th the cost, as no new tunnel blasting would be needed, but noise pollution issues would make it infeasible. The only low-speed maglev (100 km/h) currently operational, the Japanese Linimo HSST, cost approximately US$100 million/km to build.[8] Besides offering improved operation and maintenance costs over other transit systems, these low-speed maglevs provide ultra-high levels of operational reliability and introduce little noise and zero air pollution into dense urban settings. As maglev systems are deployed around the world, experts expect construction costs to drop as new construction methods are perfected.[citation needed] Historical maglev systemsFirst patentsHigh speed transportation patents would be granted to various inventors throughout the world.[9] Early United States patents for a linear motor propelled train were awarded to the inventor, Alfred Zehden (German). The inventor would gain U.S. patent 782,312 (June 21, 1902) and U.S. patent RE12700 (August 21, 1907).[10] In 1907, another early electromagnetic transportation system was developed by F. S. Smith.[11] A series of German patents for magnetic levitation trains propelled by linear motors were awarded to Hermann Kemper between 1937 and 1941.[12] An early modern type of maglev train was described in U.S. patent 3,158,765, Magnetic system of transportation, by G. R. Polgreen (August 25, 1959). The first use of "maglev" in a United States patent was in "Magnetic levitation guidance"[13] by Canadian Patents and Development Limited. Hamburg, Germany 1979There is conflict in this information. Transrapid 05 was the first maglev train with longstator propulsion licensed for passenger transportation. In 1979 a 908 m track was open in Hamburg for the first International Transportation Exhibition (IVA 79). There was so much interest that operation had to be extended three months after exhibition finished, after carrying more than 50,000 passengers. It was reassembled in Kassel in 1980. Birmingham, England 1984–1995The world's first commercial automated system was a low-speed maglev shuttle that ran from the airport terminal of Birmingham International Airport to the nearby Birmingham International railway station from 1984 to 1995. Based on experimental work commissioned by the British government at the British Rail Research Division laboratory at Derby, the length of the track was Template:M to ft, and trains "flew" at an altitude of Template:Mm to in. It was in operation for nearly eleven years, but obsolescence problems with the electronic systems (lack of spare parts) made it unreliable in its later years and it has now been replaced with a cable-drawn system. One of the original cars now sits in part of the airport with most passers-by unaware of its existence. Several favourable conditions existed when the link was built:
Japan, 1980sMaglev speeds on the Miyazaki test track had regularly hit 517 km/h by 1979, but after an accident that destroyed the train, a new design was decided upon. Tests through the 1980s continued in Miyazaki before transferring a far larger and elaborate test track (20 km long) in Yamanashi in the late 1990s. In Tsukuba, Japan (1985), the HSST-03 (Linimo) wins popularity in spite of being 30 km/h and a run of low speed in Tsukuba World Exposition. In Okazaki, Japan (1987), the JR-Maglev took a test ride at holding Okazaki exhibition and runs. In Saitama, Japan (1988), the HSST-04-1 exhibited it at Saitama exhibition performed in Kumagaya, and runs. Best speed per hour 30 km/h. In Yokohama, Japan (1989), the HSST-05 acquires a business driver's license at Yokohama exhibition and carries out general test ride driving. Maximum speed 42 km/h. Vancouver, Canada & Hamburg, Germany 1986-1988In Vancouver, Canada (1986), the JR-Maglev took a test ride at holding Vancouver traffic exhibition and runs. In Hamburg, Germany (1988), the TR-07 in international traffic exhibition (IVA88) performed Hamburg. Berlin, Germany 1989–1991In West Berlin, the M-Bahn was built in the late 1980s. It was a driverless maglev system with a 1.6 km track connecting three stations. Testing in passenger traffic started in August 1989, and regular operation started in July 1991. Although the line largely followed a new elevated alignment, it terminated at the U-Bahn station Gleisdreieck, where it took over a platform that was then no longer in use; it was from a line that formerly ran to East Berlin. After the fall of the Berlin Wall, plans were set in motion to reconnect this line (today's U2). Deconstruction of the M-Bahn line began only two months after regular service began and was completed in February 1992. The history of maximum speed record by a trial run
Guinness authorization.
Existing maglev systemsEmsland, GermanyTransrapid, a German maglev company, has a test track in Emsland with a total length of 31.5 km (19.6 mi). The single track line runs between Dörpen and Lathen with turning loops at each end. The trains regularly run at up to 420 km/h (261 mph). The construction of the test facility began in 1980 and finished in 1984. JR-Maglev, JapanJapan has a demonstration line in Yamanashi prefecture where test trains JR-Maglev MLX01 have reached 581 km/h (361 mph), slightly faster than any wheeled trains (the current TGV speed record is 574.8 km/h, 357.0 mph). These trains use superconducting magnets which allow for a larger gap, and repulsive-type Electro-Dynamic Suspension (EDS). In comparison Transrapid uses conventional electromagnets and attractive-type Electro-Magnetic Suspension (EMS). These "Superconducting Maglev Shinkansen", developed by the Central Japan Railway Company (JR Central) and Kawasaki Heavy Industries, are currently the fastest trains in the world, achieving a record speed of 581 km/h on December 2, 2003. Yamanashi Prefecture residents (and government officials) can sign up to ride this for free, and some 100,000 have done so already. Linimo (Tobu Kyuryo Line, Japan)The world's first commercial automated "Urban Maglev" system commenced operation in March 2005 in Aichi, Japan. This is the nine-station 8.9 km long Tobu-kyuryo Line, otherwise known as the Linimo. The line has a minimum operating radius of 75 m and a maximum gradient of 6%. The linear-motor magnetic-levitated train has a top speed of 100 km/h. The line serves the local community as well as the Expo 2005 fair site. The trains were designed by the Chubu HSST Development Corporation, which also operates a test track in Nagoya. Urban-type maglevs patterned after the HSST have been constructed and demonstrated in Korea, and a Korean commercial version Rotem is now under construction in Daejeon and projected to go into operation by April 2007. FTA's UMTD programIn the US, the Federal Transit Administration (FTA) Urban Maglev Technology Demonstration program has funded the design of several low-speed urban maglev demonstration projects. It has assessed HSST for the Maryland Department of Transportation and maglev technology for the Colorado Department of Transportation. The FTA has also funded work by General Atomics at California University of Pennsylvania to demonstrate new maglev designs, the MagneMotion M3 and of the Maglev2000 of Florida superconducting EDS system. Other US urban maglev demonstration projects of note are the LEVX in Washington State and the Massachusetts-based Magplane. Southwest Jiaotong University, ChinaOn December 31, 2000, the first crewed high-temperature superconducting maglev was tested successfully at Southwest Jiaotong University, Chengdu, China. This system is based on the principle that bulk high-temperature superconductors can be levitated or suspended stably above or below a permanent magnet. The load was over 530 kg (1166 lb) and the levitation gap over 20 mm (0.79 in). The system uses liquid nitrogen, which is very cheap, to cool the superconductor. Shanghai Maglev TrainTransrapid, in Germany, constructed the first operational high-speed conventional maglev railway in the world, the Shanghai Maglev Train from downtown Shanghai (Shanghai Metro) to the Pudong International Airport. It was inaugurated in 2002. The highest speed achieved on the Shanghai track has been 501 km/h (311 mph), over a track length of 30 km. The plan for the Shanghai-Hangzhou Maglev Train was approved by the central government in February 2006, with plans for completion by 2010. Under constructionOld Dominion UniversityA track of less than a mile in length has been constructed at Old Dominion University in Norfolk, Virginia. Although the system was initially built by AMT, problems caused the company to abandon the project and turn it over to the University.[14][15] The system is currently not operational, but research is ongoing to resolve stability issues with the system. This system uses a "smart train, dumb track" that involves most of the sensors, magnets, and computation occurring on the train rather than the track. This system will cost less to build per mile than existing systems. The $14 million originally planned did not allow for completion. AMT Test Track - Powder Springs, GAThe same principle is involved in the construction of a second prototype system in Powder Springs, Georgia, by American Maglev Technology, Inc., already under testing and set for completion in January 2007.[16] ProposalsMany maglev systems have been proposed in various nations of North America, Asia, and Europe. Many of the systems are still in the early planning stages, or, in the case of the transatlantic tunnel, mere speculation. However, a few of the following examples have progressed beyond that point. United KingdomLondon – Glasgow: A maglev line has recently been proposed in the United Kingdom from London to Glasgow with several route options through the Midlands, Northwest and Northeast of England and was reported to be under favourable consideration by the government; however the technology was rejected for future planning in the Government White Paper Delivering a Sustainable Railway published on July 24 2007.[17]. A further high speed link is also being planned between Glasgow and Edinburgh though there is no settled technology for this concept yet, ie (Maglev/Hi Speed Electric etc) [7] [8] [9] JapanIn April of 2007, JR Central President Masayuki Matsumoto said that JR Central would aim to begin commercial maglev service between Tokyo and Nagoya in the year 2025. VenezuelaCaracas – La Guaira: A maglev train is scheduled to be built this year connecting the capital city Caracas to the main port town of La Guaira and Simón Bolívar International Airport. Due to the extremely mountainous conditions which exist over this path, with traditional rail extensive use of tunnelling and bridging is required. Maglev systems can negotiate gradients of up to 10%, much steeper than those negotiable by standard rail systems, and as it may simply be able to climb over obstacles rather than be required to tunnel through or bridge over, this may make the maglev proposal more economically sound. The system is slated to be a stand-alone system of about 11 km. [10] ChinaShanghai – Hangzhou: China has decided to extend the world’s first commercial Transrapid line between Pudong airport and the city of Shanghai initially by some 35 kilometers to Hong Qiao airport before the World Expo 2010 and then, in an additional phase, by 200 kilometers to the city of Hangzhou (Shanghai-Hangzhou Maglev Train), becoming the first inter-city Maglev rail line in commercial service in the world. The line will be an extension of the Shanghai airport Maglev line. Talks with Germany and Transrapid Konsortium about the details of the construction contracts have started. On March 7 2006, the Chinese Minister of Transportation was quoted by several Chinese and Western newspapers as saying the line was approved. China also intends to build a factory which will mass-produce low-speed maglev trains for urban use. The location of the factory will be the Nanhui district. [11] IndiaMumbai – Delhi:A maglev line project was presented to the India transportation minister Lalu Prasad by an American company, this line if approved would serve between the cities of Mumbai and Delhi, the Prime Minister Manmohan Singh said that if the line project is successful Indian government would build lines between other cities and also between Mumbai centre and Chattrapati Shivaji International Airport. Mumbai maglev train United StatesCalifornia-Nevada Interstate Maglev: High-speed maglev lines between major cities of southern California and Las Vegas are also being studied via the California-Nevada Interstate Maglev Project. This plan was originally supposed to be part of an I-5 or I-15 expansion plan, but the federal government has ruled it must be separated from interstate public work projects. Since the federal government decision, private groups from Nevada have proposed a line running from Las Vegas to Los Angeles with stops in Primm, Nevada; Baker, California; and points throughout San Bernardino County into Los Angeles. Southern California politicians have not been receptive to these proposals; many are concerned that a high speed rail line out of state would drive out dollars that would be spent in state "on a rail" to Nevada. Baltimore-Washington D.C. Maglev: A 64 km project has been proposed linking Camden Yards in Baltimore and Baltimore-Washington International (BWI) Airport to Union Station in Washington, D.C. It is in demand for the area due to its current traffic/congestion problems. The Pennsylvania Project: The Pennsylvania High-Speed Maglev Project corridor extends from the Pittsburgh International Airport to Greensburg, with intermediate stops in downtown Pittsburgh and Monroeville. This initial project will serve a population of approximately 2.4 million people in the Pittsburgh metropolitan area. The Baltimore proposal is competing with the Pittsburgh proposal for a $90 million federal grant.The point of the project is to see if the Maglev system can function properly in a U.S. city environment.[18] GermanyOn September 25, 2007, Bavaria announced it will build the high-speed maglev - rail service from Munich city to its airport. The Bavarian government signed contract with Deutsche Bahn and Transrapid with Siemens and ThyssenKrupp for the 1.85 billion euro ($2.6 billion) project.[19] The NetherlandsA high-speed link has been proposed between Schiphol airport, Amsterdam and the city of Almere. The proposal comes from a consortium including Siemens, and is the third attempt to persuade the Dutch government to give a green light to a maglev project. The consortium says it can build the project with no government funding, if it is given a 50-year contract to operate the train.[12] Most significant accidents and incidentsOctober 1991 fireThe MLU002 (Japan) test train was completely consumed in a fire in Miyazaki. As a result, the political opposition claimed maglev was a waste of public money. New designs were made. August 2006 fireOn August 11, 2006 a fire broke out on the Shanghai commercial Transrapid, shortly after leaving the terminal in Longyang.
September 2006 crashOn September 22, 2006 an elevated Transrapid train collided with a maintenance vehicle on a test run in Lathen (Lower Saxony / north-western Germany). Twenty-three people were killed and ten were injured. These were the first fatalities resulting from a Maglev train accident. Note though, this accident was caused by human error.[20] Shanghai Protests and Government ResponseIn January and February 2008, hundreds of residents from a community in south Shanghai, China, peacefully demonstrated in downtown Shanghai to protest against the Shanghai-Hangzhou Maglev line to be built close to their homes. To avoid a government crack down, the residents described the demonstration as "going shopping". The residents are concerned with potential health hazards and loss of property value. There has been rumours that some residents living next to the Maglev line currently connecting the Pudong District and the airport have become sick due to the exposure to strong magnetic field. They also claim that since the planned line will sometimes be as close as 30 metres to their home, the property value would be substantially damaged. On 19 February 2008, the representatives of the residents filed a formal request to demonstrate with the Shanghai Public Security Bureau (PSB - the police). Reportedly, the PSB staff threatened the representatives with violence and retaliation against their families, including making reference to the Tiananmen MassacreChinese-language news report on the police threat. On 27 February 2008, the PSB issued a decision rejecting the requestChinese-language news report on the rejection. The PSB stated that the purpose of the demonstration was unclear and traffic would be disrupted. The Constitution of the People's Republic of China states that citizens have the right to freedom of speech and to demonstrate. However, no Chinese court recognizes a claim purely based on a constitutional provision. See also
Notes
Further reading
External linksWikimedia Commons has media related to Magnetic levitation train. Look up maglev in Wiktionary, the free dictionary.
|